SABINE DS80C TABLETOP BOUNDARY MICROPHONE User Manual Quick Start Guide 1

Download:
Mirror Download [FCC.gov]
Document ID	1997018
Application ID	o/UAoZc3pGleK503BD8Cpw==
Document Description	Quick Start Guide 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	308.6kB (3857497 bits)
Date Submitted	2013-06-20 00:00:00
Date Available	2013-06-20 00:00:00
Creation Date	2013-06-20 16:28:40
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2013-06-20 16:28:58
Document Title	Quick Start Guide 1
Document Creator	Adobe InDesign CS3 (5.0.4)

Digital Wireless Microphone Systems
Quick Start Guide
Setting Up Pre-Engineered SACOM Systems for Optimal Performance
On site, remote commissioning of SACOM Systems is available at no additional cost.
For support please call USA (+1) (386) 418-2000 between the hours of 9 - 5 EST., Monday thru Friday.
Note: SACOM offers free pre-engineering so that the systems arrive at your job site ready to plug and play.
Open the Cartons: Confirm everything on the packing slip is enclosed.
1.
Set up the Docking Station: SACOM transmitters are shipped with rechargeable batteries. Plug
in the charging dock, put the batteries in the transmitters, then place the transmitters in the dock
while you set up the rest of the system.
2.
Mount the Receivers in the Rack and connect them to power. Confirm the displays light up.
3.
Pre-engineered Antenna Design: If you provided SACOM with a floor plan, you will find a marked
up version in the box (or, in your Email in-box) showing the antenna design along with the
antennas and pre-made cables. Place the antennas according to the drawings.
A. Your Own Design: If you did not request an antenna design, place the antennas according
to the enclosed Antenna Applications Guide or download it from www.SacomUSA.com >
Downloads. Improper antenna placement is the main cause of poor RF performance.
B.
4.
5.
6.
Dipole Antennas: Dipole antennas mounted to the rack equipment can easily be locked
away in a closet/rack cabinet. This results in poor RF performance because there is no line
of sight between the transmitter and receiver antenna. Therefore, remote antennas are
preferred. See the Antenna Application Guide for details.
Connect the Antennas: The receiver that connects to the antennas should be set as the
Antenna Master receiver. Master is the factory default. If your system daisy-chains antennas
together, the downstream receivers should be set as Slaves. Terminators are used on the
last system in the daisy-chain. Use SACOM Remote’s Antenna Setup Wizard, which opens
automatically the first time you connect. You can also find the wizard under the SETTINGS tab
of the main page. If connecting Sacom active remote antennas, make sure the red LED lights up.
If not, check the receiver’s antenna phantom power setting using the Sacom Remote Control
Software.
Connect the analog outputs to the mixer: The system is shipped with either XLR or Euro block
connectors. The default output level is set to +4 dBu. Note that factory default for the front panel
headphone jack is set for mixed line-level out. Use SACOM Remote>Settings>Headphone, to reset
for headphones.
CAUTION! Turn off phantom power from the mixer. Phantom power distorts the audio quality
of your microphones.									
System Test: In most cases, the system is now ready to use. Confirm all channels pass audio
perfectly.
Master
Slave
Terminators
Modifications (FCC 15.21)
Changes or modifications to this equipment not expressly approved by Sabine, INC may void the user’s authority to operate this equipment.
Applies to DS80-T:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
This radio transmitter (DS80-T) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for
each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Monopole antenna, 0dbi gain, 50 ohm impedance.
Le présent émetteur radio (DS80-T) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance
requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de
l’émetteur.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
SABINE INC. l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001 l www.SacomUSA.com
For Full Control
Digital Wireless Microphone Systems
Using the SACOM remote software:
Editing Transmitter Parameters:
The easiest and most intuitive way to set the parameters of SACOM™ transmitters and receivers is with SACOM™ Remote
software. Load SACOM™ Remote (from disk or download from www.SacomUSA.com) onto a computer running Windows
XP or Windows 7 (32 or 64-bit) and connect to the receiver via USB or RS232. Then open SACOM™ Remote and select
ONLINE.
Open The Channel Edit Window:
1) The [Click to Edit] function opens the edit window of the channel you wish to edit.
2) Select the functions you want to edit and enter the parameter. (The various functions are described below.) Click [OK]
to save the changes and close the Channel Edit window.
3) You will notice that the [Needs to Sync] alert is lit. This indicates that one or more parameters are in queue in the receiver
ready to be downloaded and implemented with the next transmitter Sync of the channel.
1)
Click to Edit the channel’s parameters
2)
Select the new parameter values and click OK to
save changes to the receiver.
SACOM Remote provides the following functions:
3)
The “Need To Sync” alert is lit. Sync the transmitter to apply the selected
parameters.
1. File: Save a PDF image of the screen.
2. Settings:
A. Phantom Power: Turn antenna phantom power on or off. Default = ON.
B. Redundancy: Set adjacent pairs of receivers to redundancy mode. Default = OFF.
C. Headphone Mode: Toggles the mixed output jack from headphone mode to a balanced line output. Default = Balanced
line output.
3. Ethernet Settings: If using Ethernet, assign the proper IP address to the Sacom Receiver.
4. RF Scan - RF Plot: Shows the RF strength of each antenna in a SACOM system and shows if there is outside interference.
5. Presets: Save or load preset system parameters configurations. Default = As Ordered.
6. GPIO: Assign contact closure functions and setup for RS232 control. Default = RS232 - Output mutes.
7. Security: Password to prevent unauthorized changes: (Under construction). Default = none.
8. Alerts: Send alerts to authorized personal when preventive maintenance is required of if there is a fault. Default = none.
9. Update System: Checks to see if the system has the most current firmware and provides a wizard for updating the firmware.
10. Help:
A. Tutorials: Setting parameters, Antenna Application Guide, etc.
B. About: Shows vital statistics for each component of the system
Default Transmitter Preamp Gain Settings:
Transmitter + Last 4 digits of serial Number
Default Transmitter Preamp Gain
BLT XXXX
10 dB
HH XXXX
H18 = 0dB / H10 = 10dB
PDM XXXX
10dB
BDM XXXX
20dB
Key:
BLT = Beltpack
HH = Handheld Mic
PDM = Podium Mic
BDM = Boundary Mic
SABINE INC. l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001 l www.SacomUSA.com
Digital Wireless Microphone Systems
How to sync transmitters with the receiver:
1) Locate the IR (infrared) Sensor on the transmitter
IR
IR
IR
IR
IR
ON/OFF
USB
USB
IR
ON / OFF
2) Power on the transmitter.
3) Hold transmitter about 6 inches from the corresponding receiver module with the IR sensor aimed at the receiver module.
4) Simultaneously press the two buttons on the bottom of the corresponding receiver module to start sending the IR signal.
“SYNCING” shows on the receiver OLED when the IR signal starts. “SYNC OK” shows when the sync is successful. Repeat the
procedure if the receiver display shows “SYNC FAILED”. It is not necessary to press any buttons on the transmitter during the
procedure. Note: You may get a “Sync Failed” message if the receiver antennas are not in the same room as the receiver. In this
case verify that either the transmitter display shows “Sync Good” OR the green LED on the transmitter flashes. Also make sure to
dock each transmitter after syncing to avoid 2 transmitters being synced to the same receiver frequency.
NOTE: The transmitter and receiver are assigned a new, random AES 256-bit encryption key every time they are synced.
How to read the LED:
1. The Gooseneck or
Boundary Mic is in use:
RED = AUDIO MUTE
GREEN = AUDIO PASSES
BLINKING RED = BATTERY IS LOW
BLINKING GREEN = SYNC SUCCESSFUL
2. The Gooseneck Battery Cassette and
Boundary Mic are in the docking station:
RED = CHARGING
OFF/OR GREEN = FINISHED CHARGING
BLINKING RED = CHARGING ERROR (RE-SEAT THE
TRANSMITTER AND CHECK THE BATTERIES)
3. When the Hand-held Mic and the 		
Belt-pack are in the Docking Station:
The OLED shows
the battery status
NOTE: All transmitters placed in the charging dock will “RF MUTE”.
SABINE INC. l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001 l www.SacomUSA.com
Digital Wireless Microphone Systems
Receiver:
FRONT PANNEL:
SACOM™ receiver main-frames hold either four or eight, independent, 24-bit digital audio receiver modules. There is a front-panel
mixed audio output for headphones or direct recording. Each module shares the main-frame’s two antennas for full-diversity. Up to
eight receiver main-frames can be daisy-chained together into an antenna network that shares two antennas. This eliminates the
need for external antenna distribution amps. Main-frames can be connected to form an Ethernet network that monitor and control
the system via a computer. Main-frames also have USB and RS233 connections for serial monitor and control. AES/EBU digital
audio output and word clock sync is optional.
TM
DS8800
DIGITAL SPECTRUM SERIES
Made In USA
USB
POWER
PHONES
1.
2.
3.
4.
5.
6.
Antenna Front Mounting Hole: Use back-to-front TNC cables included.
Receiver Module. See details below
Mixed audio volume control.
USB Port. Connect to computer for SACOM™ Remote control. Run software to monitor/edit system parameters, scan for RF
interference and download firmware upgrades.
Mixed audio output, 1/4” (See headphone mode - Pg. 2) phone jack for monitoring individual channels or mixed channels.
Power Switch.
RECEIVER MODULE:
MODULE:
1. Select Next Function: Move the cursor to the next menu function on the display
Modules are designed for quick and easy
field replacement for added redundancy.
(Under construction)
2. IR Sync LED: Sends IR information to SYNC the receiver and transmitter (SYNC pg3)
3. Select Previous Function: Move the cursor to the previous menu function
(Under construction)
IR
SELECT
AUDIO
BATTERY
SLOT 3
CH 1
ON
AES256
FUNCTION
(SYNC)
STATUS
4. Soft Key Left: Select the choice displayed in the bottom left of the display
4 & 6 pressed at the same time: Sends SYNC signal from receiver to transmitter (SYNC pg3)
5. Status LED:
• Green --> The channel is ON and un-muted
• Red --> The channel is OFF
• Flashing Red --> Encryption key mismatch, Re-sync receiver with transmitter
• Amber --> The receiver is muted or GPIO is triggered
6. Soft Key Right: Select the choice displayed in the bottom right of the display
RF BARS
ANTENNA DIVERISITY
AUDIO LEVEL
BATTERY LEVEL
CHANNEL NAME
ENCRYPTION
STATUS: (Colored text indicates status)
ON = Green
OFF = Red
MUTE = Amber
KEY = Flashing Red (“KEY” = mismatched encryption key)
FREQUENCY
SABINE INC. l 13301 NW US Highway 441 l Alachua, Florida 32615-8544 USA l Phone: +USA (386) 418-2000 l Fax: +USA (386) 418-2001 l www.SacomUSA.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2013:06:20 16:28:40-04:00
Creator                         : Adobe InDesign CS3 (5.0.4)
Modify Date                     : 2013:06:20 16:28:58-04:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2013:06:20 16:28:58-04:00
Creator Tool                    : Adobe InDesign CS3 (5.0.4)
Format                          : application/pdf
Document ID                     : uuid:758b89d5-b7f9-4c39-84f1-3a7e342e1ffa
Instance ID                     : uuid:c313f542-fafb-4d79-8988-ecbe8381f25e
Producer                        : Adobe PDF Library 8.0
Page Count                      : 4

EXIF Metadata provided by EXIF.tools