SAGEMCOM BROANDS DCIW387 Set up box User Manual Safety FCC Instructions DCIW387 ATN v2
SAGEMCOM BROADBAND SAS Set up box Safety FCC Instructions DCIW387 ATN v2
User manual_Safety_FCC Instructions DCIW387 ATN v2
Safety Information.
Important Safety Compliance Instructions
•Read and retain instructions from the manufacturer of your equipment.
• Place the electronic equipment in a location that is easily accessible and close enough to an
electrical outlet to accommodate the length of the power cord and unplugged quickly in case of
a problem.
•Place the electronic equipment on a stable surface. The surface must support the size and
weight of the electronic equipment.
•Do not place other equipment, lamps, books, vases with liquid, or any other object on the top
of the electronic equipment.
•Do not place in any of the following locations: - Outdoors - On a bed, sofa, rug, or similar
surface - Over a radiator or a heat register - In an enclosure, such as a bookcase or equipment
rack, unless the installation provides proper ventilation
• Before cleaning the electronic equipment, unplug it from the electrical outlet. Use a damp cloth
to clean. Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static
cleaning device (dust remover) to clean the electronic equipment.
• Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
• Do not expose the electronic equipment to liquid or moisture.
• Do not place on a wet surface. Do not spill liquids on or near the electronic equipment.
• Do not use accessories with the electronic equipment unless recommended by your cable
service provider.
• Do not overload electrical outlets, extension cords, or integral convenience receptacles, as this
can result in a risk of fire or electric shock.
• Ground (earth) your cable system to provide some protection against voltage surges and built-
up static charges. Plug your electronic equipment into a surge protector to reduce the risk of
damage from lightning strikes and power surges. If you have questions, call your cable service
provider.
• Arrange all power cords so that people can’t walk on the cords, place objects on the cords, or
place objects against the cords, which can damage them. Give particular attention to the cords
at the point at which the cord connects to the plug, at electrical outlets, and at the places where
the cords exit the electronic equipment.
• A label on the electronic equipment indicates the correct power source. Operate only from an
electrical outlet that has the voltage and frequency that the label indicates. If you are unsure of
the type of power supply to your residence, consult your local power company.
•The electronic equipment has a two-prong plug. If this plug is polarized, it has one wide prong
and one narrow prong. This plug fits only one way. If you are unable to insert this plug fully into
the outlet, contact an electrician to replace your obsolete outlet.
•Do not open the cover of the electronic equipment. Refer all servicing to qualified personnel
only.
• For damage that requires service, unplug the electronic equipment from the electrical outlet.
Refer to qualified personnel when any of the following occurs:
There is damage to the power plug
Liquid enters the electronic equipment
There is exposure to rain or water
Operation is not normal
If you drop or damage the electronic equipment
If the electronic equipment exhibits a distinct change in performance.
Upon completion of any service or repairs to the electronic equipment, the service technician
will perform safety checks to determine that the equipment is in proper operating condition.
FCC ID : VW3DCIW387
• The electronic equipment was qualified under test conditions that included the use of the
supplied cables between system components. Use only the provided power and interface
cables and install them properly.
• Installation of electronic equipment must be in accordance with national wiring codes and
conform to local regulations.
• Connect the manufacturer supplied AC to DC power adapter. Only use a manufacturer
supplied and approved power adapter. The Sagemcom DCIW387 ATN device requires the use
of a 12 VDC, 2 A power adapter in compliance with LPS of clause 2.5 of IEC /UL 60950-1
Edition. Always first plug the mains adapter lead into the DCIW387 ATN then the mains lead
into the mains adapter, and finally the mains lead into the mains socket. If you do not follow this
order of connections you may get an electric shock. Make sure that the mains lead is properly
inserted into the power supply unit, and that it is correctly pushed into the recess. It is very
important to push the mains lead until the recess bottom. If it is incorrectly connected this may
cause a risk of fire or electric shock.
• The coaxial connector “cable” of this product is intended to be connected to a system outlet
whose shielding of the coaxial cable is imperatively earthed, in accordance with clause 7.3 of
IEC /UL 60950- 1 Edition 2.
Important: The information shown in the FCC Declaration of Conformity paragraph below is a
requirement of the FCC and is intended to supply you with information regarding the FCC
approval of this device.
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause
undesired operation.
Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The device produces radio frequency energy in the 2.4 GHz and 5 GHz spectrum. The device
should be positioned to keep a minimum distance of 30 cm (0.98ft) from the radiating element to
any nearby person.
Modifications
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
FCC Responsible Party for DCIW387 ATN:
Sagemcom USA
14651 N. Dallas Parkway
Suite 900
Dallas, TX 75254
Phone: 972-674-4100