SAGEMCOM BROANDS SE680 WIMAX Terminal Station User Manual SE680 WiMAX

Download:
Mirror Download [FCC.gov]
Document ID	1586767
Application ID	Bax38FLrF0LS/eDrvVOX1w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	85.21kB (1065089 bits)
Date Submitted	2011-11-23 00:00:00
Date Available	2011-11-23 00:00:00
Creation Date	2017-11-03 05:09:33
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-03 05:09:33
Document Title	SE680 WiMAX
Document Creator	FrameMaker 7.1
Document Author:	© Sagemcom Broadband SAS

SE680 WiMAX
User Guide
This device works in a frequency band for which a general licence might have to be
obtained. Please contact your service provider or your National Authority for Frequency
Management about licensing before putting this device into service.
Contents
Contents
For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information on Specific Absorption Rate (SAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes on the user guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The SE680 WiMAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
What is WiMAX? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The SE680 WiMAX modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the SE680 WiMAX modem . . . . . . . . . . . . . . . . . 10
Choosing the location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wall mounting (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the SE680 WiMAX modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the outdoor modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a PC or switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching on the devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
11
12
12
12
14
Configuration with the Web browser . . . . . . . . . . . . . . . . . 15
User interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Launching the user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User interface elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Home page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
18
18
18
19
Basic Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Starting the Basic Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering access data for the WiMAX network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up Internet access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Establishing a radio connection with a WiMAX network . . . . . . . . . . . . . . . . . . . . .
Precisely aligning the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
20
21
21
22
Contents
Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setting the operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Internet access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up the Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up DNS servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling or disabling the firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the firewall for a selected PC (Exposed Host) . . . . . . . . . . . . . . . . . .
LAN configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WiMAX configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
25
25
26
26
27
28
29
30
Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
System password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
32
33
33
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local network LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
36
36
37
Using the SE680 WiMAX . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other faults and problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before contacting customer service or your provider . . . . . . . . . . . . . . . . . . . .
Checking the connection to the SE680 WiMAX . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Web browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up an HTTP proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Allowing pop-up windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Putting into service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CE declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open Source Software used in the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty regarding further use of the Open Source Software . . . . . . . . . . . . .
Open Source Software used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open Source Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
42
42
43
44
44
45
46
46
47
47
48
48
49
49
50
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
For your safety
For your safety
 Please read the safety instructions carefully before putting into service.
Safety precautions
General safety instructions
 Only pass on the SE680 WiMAX modem to third parties with this user guide and the
assembly instructions.
 The SE680 WiMAX modem must only be installed and put into use by a qualified
electrician in accordance with the supplied installation instructions.
 National laws and regulations must be considered before putting the device into
service.
 These devices are professional IT equipment. Keep the devices beyond the reach
of children.
Safety instructions for connection
 Only use undamaged original accessories.
 The outdoor modem must only be installed by qualified electricians in accordance
with the assembly instructions.
Safety precautions for the SE680 WiMAX modem
 The operation of medical appliances may be affected. Be aware of the technical
conditions in your particular environment, e.g. doctor's surgery.
 The SE680 WiMAX modem can interfere with the functioning of medical devices
such as pacemakers. Keep at least 20 cm between the devices and the pacemaker.
For more information consult your doctor.
 Do not operate the indoor unit under the influence of direct heat sources (e.g.
directly in the sun).
 The SE680 WiMAX modem complies with the regulations on limiting the effect of
electromagnetic fields on the general population.
 Do not use the devices in environments with a potential explosion hazard, e.g. auto
paint shops or in a humid environment (bathroom etc.).
 Only clean the SE680 WiMAX modem with a soft anti-static cloth.
Trademarks
 Microsoft Windows 2000, Windows XP, Windows Vista and Internet Explorer are
registered trademarks of the Microsoft Corporation.
 Mozilla Firefox is a registered trademark of the Mozilla Organization.
Notes on the user guide
Information on Specific Absorption Rate (SAR)
This device meets the limits for protecting the health of the public from the effecs of
exposure to electromagnetic fields when it is operated in connection with the designated antenna(s) like described in the user manual.
Your device is a radio transmitter and receiver. It is designed and manufactured not to
exceed the limits for exposure to emission from electromagnetic fields recommended
by international guidelines from the International Commission on Non-Ionizing Radiation Protection (ICNIRP). These limits are part of comprehensive guidelines for the protection of the public and establish permitted levels of exposure to electromagnetic radiation for the population. The guidelines were confirmed by independent scientific
organisations through periodic and thorough evaluation of scientific studies. The limits
include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.
The exposure limit employs a unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit stated in the international guidelines is 2.0 W/kg. Tests for
SAR are conducted in all frequency bands with the device transmitting at its highest
power level with minimum possible distance to the body. The actual SAR level of the
device during operation with the designated antenna(s) is below the maximum value
and is additionally decreased by a distance to the device. This is because the device is
designed to operate at multiple power levels so as to use only the power required to
enable seamless network connection.
Notes on the user guide
This user guide describes how to set up and configure the SE680 WiMAX modem.
Installation of the individual components is dealt with in the assembly instructions,
which you received together with the SE680 WiMAX modem.
 Please read the user guide carefully before using the devices for the first time.
 Also note the product information on the Internet at www.sagemcom.com
The SE680 WiMAX
The SE680 WiMAX
What is WiMAX?
WiMAX stands for "Worldwide Interoperability for Microwave Access", a modern wireless network technology that enables fast Internet connection even in remote areas.
With WiMAX technology you are no longer dependent on a DSL infrastructure in your
home or place of work. Instead, you connect your PC or network wirelessly to radio
stations operated in your region by your provider. As a result, WiMAX gives you fast,
economical broadband Internet access, even in places that are not connected to the
DSL cable network.
The WiMAX standard IEEE 802.16 generally defines WiMAX technology. Your SE680
WiMAX modem already meets the latest IEEE 802.16e-2005 standard, a mobile
WiMAX standard that offers many extra possibilities.
The SE680 WiMAX modem
With your SE680 WiMAX modem, you can make use of everything the Internet has to
offer:
 Downloads




– Even large files download quickly to your PC.
– Complex Website designs are no longer characterised by the time they take to
download – you can enjoy flash animation and high-resolution graphics immediately after clicking on a link.
Audio
– Play back audio files straight from the Internet.
– Listen to the radio via the Internet in superb digital quality.
Video
– View short or longer films you find on the Internet without tedious waiting times.
– Watch television via the Internet (IPTV).
– Use "Video on Demand" and order films that are transmitted to you via the
Internet.
Real time
– Take part in video conferences and feel as if you are sitting in the same room as
the people you are talking to.
– Speak to and see your chat partners.
VoIP
– Benefit from the economical telephone rates for Internet telephony (Voice over
IP, VoIP). Your PC does not even need to be switched on.
Scope of delivery
Product features
 Wireless high-speed Internet access with a transmission rate of up to 20Mbps
(14 Mbps downlink, 6 Mbps uplink)
 Standards compliant: IEEE 802.16e-2005
 Compatible with all usual operating systems
 Suitable for home and business facilities
 Multi-protocol support: TCP/IP, FTP, HTTP and other Internet related protocols
 Compact design and easy installation
 DHCP server and routing functions
 High performance and Quality of Service
Scope of delivery
 1 SE680 WiMAX modem, comprising:




– 1 Outdoor modem (to be installed by an electrician)
– 1 Indoor unit
1 power lead (two-pin)
1 Ethernet cable (length 1.8 m)
1 Set of assembly material, incl. assembly instructions
1 User guide
Scope of delivery
Connectors and LEDs
Connector for the two-pin power lead, see "Switching on the
devices" on page 14.
CONNECT
The LED shows whether or not the indoor unit is properly connected with the outdoor modem.
 Green: The indoor unit is properly connected with the out-
door modem.
FAULT
The LED shows whether or not the indoor unit is properly connected with the outdoor modem.
 Red: The connection between the indoor unit and the out-
door modem is faulty.
ON
The LED shows that power is being supplied.
IN
Ethernet connector for data exchange with a PC or network
(RJ45, 10/100 Base T), see "Connecting a PC or switch" on
page 12.
OUT
Ethernet connector for connection with the outdoor modem
(RJ45, power supply and data transmission), see "Connecting
the outdoor modem" on page 12.
 Green: The SE680 WiMAX modem is powered correctly.
Clips for wall mounting
Installing the SE680 WiMAX modem
Installing the SE680 WiMAX modem
The SE680 WiMAX modem essentially comprises three components:
 Outdoor modem with integrated antennas (X-pol)
 Indoor unit
The SE680 WiMAX modem must be assembled and put into service by
a qualified electrician.
The information in the enclosed assembly instructions must be noted.
This user guide assumes that the work required for outside installation has already
been carried out.
Therefore, installation is described below starting with how to put the indoor unit into
service.
PC with SE680 WiMAX modem
10
Base station
System requirements
Choosing the location
 Choose the location so that you can easily establish the following connections:
– Ethernet cable socket, which, for example, establishes the connection to the outdoor modem through a wall duct.
– Ethernet cable socket for connection with a PC or network.
– Connection of the power lead with a mains socket.
 First choose the location for the indoor unit:
– Consider the stated temperature range for the indoor unit when choosing the
location (see "Specifications" on page 46).
 The indoor unit can be operated either on a horizontal surface or mounted on a wall.
Make sure the connections cannot become loose and that the LEDs are clearly visible.
 Lay the cables in such a way that nobody can tread on or trip over them.
System requirements
To install and get started with the indoor unit, the following requirements must be fulfilled:
 The outdoor modem has been properly installed and is ready for use. The associ-
ated Ethernet cable is fitted with an RJ45 plug and ends close to the indoor unit.
 PC with a LAN interface 10/100BaseT or an Ethernet network
10/100BaseT. The network adapter must support one of the following modes:
10BaseT Half Duplex, 10BaseT Full Duplex, 100BaseT Half Duplex,
100BaseT Full Duplex.
 The TCP/IP protocol has to be set up on the PC (standard installation for Windows
XP and Windows Vista; if you are using a different Windows operating system, read
the separate instructions on network configuration on the product CD, if necessary).
Wall mounting (optional)
The indoor unit is fitted with two clips for wall mounting. Wall mounting is not absolutely
necessary, but is recommended to make the cable connections mechanically secure.
 Use screws, anchor fittings and cable clamps to mount the indoor unit on a wall.
Make sure the LEDs are easily visible.
11
Wall mounting (optional)
Connecting the SE680 WiMAX modem
Set up the connections on the indoor unit in the following order:
1. Connect the outdoor modem.
2. Connect the PC or the switch/hub.
3. Connect the indoor unit to the mains power supply and switch all the devices on.
Connecting the outdoor modem
After the outdoor modem has been installed correctly, the associated Ethernet cable
(with RJ45 plug) is available close to the indoor unit.
 Insert the Ethernet cable plug into the OUT socket on the indoor unit. You should
be able to hear the clips on the RJ45 plug click into place.
Connecting a PC or switch
Use either the Ethernet cable that is supplied or a standard network cable
(CAT-5) for the connection to the PC or switch. It does not matter if the
Ethernet cable has straight or crossed wiring.
You must use a shielded Ethernet cable.
12
Wall mounting (optional)
Connecting the indoor unit to a PC
 Connect an Ethernet cable plug to the IN socket on the indoor unit.
 Connect the other plug of the Ethernet cable to the LAN interface on the PC.
Connecting the indoor unit to a switch
 Connect an Ethernet cable plug to the IN socket on the indoor unit.
 Connect the other Ethernet cable plug to the switch or hub.
 For configuration, please refer to the user guide of your switch or hub.
13
Wall mounting (optional)
Switching on the devices
Only use the SE680 WiMAX modem with the supplied mains cable.
Refernece number: C39280-Z4-C584
Manufacturer: PhiHong
Type: POE30U-560(G)-S
Input: 100-240V, 0.95A AC
Output: 56V, 0,55A DC
 Connect the power lead to the indoor unit.
 Connect the power lead of the indoor unit to the mains power supply. The outdoor
modem is powered via the Ethernet cable and does not require its own mains connection.
The system starts booting and performs a self-test.
After the self-test, the SE680 WiMAX modem continually attempts to register with
a base station. Registration with the base station may be successful immediately;
otherwise, registration will take place when your SE680 WiMAX modem is being
configured.
 Check the LEDs during startup:
LEDs during startup:
– The ON power supply LED lights up green, and the SE680 WiMAX modem
starts a self-test.
– The FAULT LED (red) and the CONNECT LED (green) light up for approximately
1 second and then go out. If the connection to the outdoor modem is then found
to be free from errors, the CONNECT LED is continuously lit up green. If an error
occurs, the FAULT and CONNECT LEDs start to flash alternately at regular intervals.
14
Configuration with the Web browser
Configuration with the Web browser
You do not need to install any software on your PC to configure your SE680 WiMAX
modem; the configuration program is stored on the device. Open this software in the
same way as an Internet page in the Web browser and make the required settings. Your
settings are then stored directly on the device.
On startup, the Basic Setup Wizard helps you set up a connection to the WiMAX network and configure your Internet access.
For experienced users:
– IP address: 192.168.2.1
– Subnet mask: 255.255.255.0
Presentation of the configuration program
To configure your SE680 WiMAX modem, we recommend the Microsoft Internet
Explorer version 7.0, Mozilla Firefox version 2.0 or their higher versions. However, you
can also use most other or older Web browsers.
Number and amount of functions and settings provided by the configuration program may differ specific to a project.
User interface
Launching the user interface
 Open your Web browser.
 Enter the IP address of your SE680 WiMAX modem in the address field of your Web
browser:
http://192.168.2.1
 Press Enter (Return).
If a system password has been set up on your SE680 WiMAX, the login screen will now
open.
Enter the system password supplied by your provider in the text box and click Ok.The
start page (Home) of the user interface opens, in which you can change the language
if necessary ( page 18).
Change the system password later to one of your own (see "System password" on
page 31).
If no system password has been set up on your SE680 WiMAX, a security warning will
appear first. You should then assign a system password as soon as possible.
 Confirm the security warning with Ok.
The user interface start page opens.
15
User interface
If the login screen does not open:
 Check the connections; see "Connecting the SE680 WiMAX modem" on page 12.
 If you use a firewall on the PC, it must allow connection to the SE680 WiMAX. If
applicable, switch off the firewall for a test; if you can then open the login screen,
configure the firewall accordingly. For details, refer to the user guide for your firewall.
If you have changed the standard settings on your PC, you might not be able to open
the configuration pages.
 For details on how to find and rectify the fault, see "Troubleshooting" on page 40.
Saving the user interface address
 You can add the address of the registration page to your favourites/bookmarks so
that you will no longer need to enter the IP address manually in future:
– Internet Explorer: Add to Favorites button
– Firefox: Bookmarks > Add Bookmark
User interface elements
The user interface you open with the Web browser is divided into the following sections:
Basic Setup Wizard
Home
Status
Advanced Settings
Language
Logout
Operating Mode
Internet
...
...
...
16
Tab selection:
Open the Home, Basic Setup Wizard, Advanced Settings or Status tabs to
display the contents of each configuration area.
Language button:
Select your language. This button is only available on the Home screen.
Logout button:
The button is only displayed if a system password is set up.
Log off from your SE680 WiMAX modem.
User interface
Open Help window button:
Open the online Help relating to the menu item currently in the working area.
Menu area:
Click the menu items to display the respective pages of the currently open configuration area or a submenu.
Working area:
Check the settings on your SE680 WiMAX modem and change them as necessary.
Buttons
Open online Help.
Click on this button if you require information about the screen you currently have open. The corresponding Help topic is opened.
Logout
Button with which you end the connection between the PC and the SE680
WiMAX modem.
Back
Return to the previous screen in the Basic Setup Wizard.
Next
Move on to the next screen in the Basic Setup Wizard.
Cancel
Changed settings are not applied and you return to the highest level.
Ok
Save the settings and return to the highest level.
End
Save the settings and exit the Basic Setup Wizard.
You will see other buttons depending on the screen currently open. If you require further
information about these, open the online Help at the appropriate place using the question mark button.
Input fields
On the configuration screens, change the required settings using the following input
fields:
Option fields:
Two or more fields, of which one is activated. As soon as you click in
another option field, it is activated and the one previously selected is
reset. You will find option buttons wherever there is a choice between
several possibilities.
Text field:
Enter text or digits. Click in the field to activate input mode. You will find
text fields at points where you can specify text or numbers as required,
e.g. a new system password.
17
User interface
Setting the language
The user interface is initially displayed in the language that has been set by your operator. Other languages may be available.
 If you wish to change the preset language, click on the Language button at the top
right. This opens the page for setting the language.
 Click on the arrow next to the selection field to open it and select your language.
 Click on Ok to change the language.
Opening online Help
There is an online Help for each screen of the configuration program, which you can
open directly on the screen.
 Click on the question mark button at the top right.
The online Help is shown in the right pane of the configuration program.
 If necessary, click on Open Help window to open the online Help in a separate
window.
Menu structure
The menu of the user interface on your SE680 WiMAX modem is split into the following
main areas: Home, Basic Setup Wizard, Advanced Settings and Status. Under
these menu options, you will find the following areas:
Menu
Description
Home
Brief description of all the menus in your SE680 WiMAX modem,
as well as the connection status and the language change feature;
see "User interface" on page 15.
Establish a connection to the WiMAX network, optimise the
antenna direction and set up your Internet connection, see "Basic
Setup Wizard" on page 20.
Configure your Internet access and your local network and perform administration tasks. For example, you can enter a system
password for access to your SE680 WiMAX or change it, see
"Configuration with the Web browser" on page 15.
Obtain information about the operating status of your SE680
WiMAX modem and read off the device and version numbers as
well as IP addresses; see "Status" on page 34.
Internet
See "Internet" on page 35.
Basic Setup Wizard
Advanced Settings
Status
18
Local Network
See "Local network LAN" on page 36.
Device Status
See "Device status" on page 36.
Radio Status
See "Radio status" on page 37.
The Home page
The Home page
Once you have logged in successfully to the SE680 WiMAX modem, you will see the
Home page for the device software. The start screen offers an overview of all areas of
the configuration program:
Menu
Description
Basic Setup Wizard
Perform the basic configuration and set up the radio
connection to the WiMAX network ( page 20).
Perform advanced configuration and administration
tasks ( page 23).
Obtain information on the status of your SE680 WiMAX
( page 34).
Advanced Settings
Status
In the area to the right of the start screen, you will see the connection status of your
SE680 WiMAX modem:
 connected = The SE680 WiMAX modem has established a radio connection with
a WiMAX network. You will see the connection duration in brackets and in the format ddd:hh:mm:ss (d=days, h=hours, m=minutes, s=seconds).
 disconnected = The SE680 WiMAX modem is trying to establish a connection with
a WiMAX network.
To configure your SE680 WiMAX modem, use the Basic Setup Wizard, which will help
you establish a radio connection.
Connecting to the Internet manually
Once you have configured your Internet access (see page 20 and page 25), you can
establish a manual connection to the Internet on the start screen if you have selected
Connect on demand as the Connection mode.
To establish or end an Internet connection manually:
 Open the start screen of the SE680 WiMAX as described on page 15.
 If you have already started the user interface, click the Home tab at the top left of
the window.
 Click Connect to establish a connection to the Internet.
 Click Disconnect if you no longer require the connection.
19
Basic Setup Wizard
Basic Setup Wizard
The Basic Setup Wizard helps you start up your device and guides you step by step
through the configuration process with the most important settings.
The Basic Setup Wizard comprises the following steps:
 Entering the access data for the WiMAX network
 Configuring the Internet access
 Positioning the device
 Scanning the frequencies to establish a radio connection with a WiMAX network
 Exact alignment of the antenna to optimise the quality of the connection
You can check all the configuration settings that you make with the Basic
Setup Wizard later via the Advanced Settings menus and, if necessary,
change them, see "Advanced Settings" on page 23.
Depending on the pre-configuration of your device some of the menu
entries and configuration possibilities might be missing in your device.
Starting the Basic Setup Wizard
 To start the Basic Setup Wizard, click the Basic Setup Wizard tab.
 Click Next.
Entering access data for the WiMAX network
On this page you enter the data for authentication of your device on the WiMAX base
station. You will need the access data supplied by your WiMAX operator for this.
 Activate the Authentication option, if this is required by your WiMAX operator.
 Enter the access data and click Next.
Setting up Internet access
To allow users in your local network access to the Internet, set up the Internet connection of your device using the information supplied by your Internet provider.
 Enter the access data and click Next.
20
Your SE680 WiMAX can be used as an Internet router or bridge. For
more on this see "Setting the operating mode" on page 24.
Establishing a radio connection with a WiMAX network
Adjusting the antenna
 Adjust your SE680 WiMAX modem facing towards the base station.
 Click Next.
Establishing a radio connection with a WiMAX network
The Basic Setup Wizard will now scan the frequencies to establish an initial radio connection to a WiMAX network.
The frequency scan begins automatically. A progress bar indicates how far the scan
has progressed. In addition, you will see in the Remaining time area roughly how
much time is still needed for the complete scan. Depending on how your SE680 WiMAX
modem has been preconfigured by your provider, the scan can last several minutes
before the first radio connection is established.
During the scan, the SE680 WiMAX modem must not be moved; this is
the only way to guarantee a complete scan with the current antenna
alignment.
As soon as a radio connection has been established with a WiMAX network, the scan
will end. The progress bar is fully filled in and the display in the Remaining time area
jumps to 0 seconds.
 If the scan has been successful, read on in Chapter "Precisely aligning the antenna"
on page 22.
If the scan has not been successful:
The integrated antenna is a directional antenna this means that it must at least be pointing roughly in the direction of a WiMAX network base station in order to establish a
radio connection. The access data must also have been entered correctly.
If the scan was not successful:
 First check your access data by going back to the WiMAX configuration page
( page 20).
 If you have entered your access data correctly, adjust the SE680 WiMAX modem.
 Turn your SE680 WiMAX modem by approx. 20°. Turn or move the device a little at
a time and note the signal strength display. Use this to move the antenna to the
position with the best signal strength.
21
Establishing a radio connection with a WiMAX network
Precisely aligning the antenna
Once you have established a wireless connection to a WiMAX network, align your
SE680 WiMAX modem precisely using the Basic Setup Wizard.
Take extra care to align the SE680 WiMAX modem precisely. The better
the connection quality, the faster your Internet connection will be in the
future.
To obtain precise alignment of the SE680 WiMAX modem, turn it a little at a time.
 When a connection to a WiMAX network has been established, click on Next to
make fine adjustments to the antenna.
The quality of the radio connection is represented graphically by the Signal quality bar.
The longer the bar is, the better the radio connection. Try to obtain the best possible
radio connection setting.
 If you are unable to check the display of the signal quality on the screen while align-
ing the antenna:
Activate the Audible feedback option to obtain information about the signal quality
by means of beeps. The closer together the sequence of beeps, the better the connection quality.
 Turn or move the SE680 WiMAX modem a little at a time and note the signal quality
display. Use this to move the antenna to the position with the best signal quality.
If you have turned your SE680 WiMAX modem too far, the connection might break. You
should then return to the alignment that provided a connection and repeat the procedure for establishing a connection to the WiMAX network. Then make any fine adjustments step by step.
The connection quality can be detected in two different ways:
 CINR (Carrier to Interference and Noise Ratio) measures the signal
quality.
 RSSI (Received Signal Strength Indication) measures the signal
strength.
The bar indicates either RSSI or CINR values. The used method is preconfigured by your operator. If RSSI is used the bar is labeled Signal
strength.
When your SE680 WiMAX modem is optimally aligned:
 Click End to close the Basic Setup Wizard and apply the settings you have made.
Make sure that in future your SE680 WiMAX modem is always in the set position.
22
Advanced Settings
Advanced Settings
In the Advanced Settings menu, you can configure all the options for the SE680
WiMAX. If required, you can also change the settings you made using the Basic Setup
Wizard. The following table contains the options available in this menu.
Menu
Description
Operating Mode
Here you can define whether your SE680 WiMAX will be
used as a router or a bridge for the Internet access
(page 24).
Internet
Here you can configure your Internet access. This menu
covers all setting options for the Internet (page 25).
Here you can configure your local network, e.g. change the
private IP address of the SE680 WiMAX or make settings
for the DHCP server (page 29).
Here you can change the access data for your WiMAX
access (page 30).
Here you can do various administration tasks, e.g. assign a
system password (page 31) or reset the configuration to the
factory defaults (page 32). You can also load new firmware
(page 33)
Local Network
WiMAX configuration
Administration
All Advanced Settings pages contain Ok and Cancel buttons.
 Click Ok to confirm your entries.
 Click Cancel to close a page without applying the changes.
Depending on the pre-configuration of your device some of the menu
entries and configuration possibilities might be missing in your device.
23
Advanced Settings
Setting the operating mode
Via the operating mode, you define the role your SE680 WiMAX will play when establishing and administering Internet connections.
You can run your SE680 WiMAX in the following operating modes:
Router
Your SE680 WiMAX serves as an Internet router for the network components connected to the indoor unit LAN port, i.e. it establishes the connection to the Internet and ensures the transfer of the communication data to
and from the Internet (default).
Bridge
The network components initiate and control their Internet connection themselves. Your SE680 WiMAX only allows the communication data to and
from the Internet to pass through.
 To change the operating mode, open the Advanced Settings tab and select Oper-
ating Mode from the menu.
When you change the operating mode, your device is restarted.
In Bridge mode, the following functions are no longer available:
 The DHCP server of the SE680 WiMAX is deactivated ( page 29) because the
network components receive IP addresses in the public network.
If you want to access the configuration program of the SE680 WiMAX via your PC,
you must connect the PC directly to the indoor unit LAN port. You must also temporarily assign it a static IP address in the address range of the SE680 WiMAX. If you
want to use the Internet again after this, reset your PC to “automatic IP address”.
For details see the document “Configuring the local area network” on the product
CD.
 The firewall of your SE680 WiMAX is disabled and cannot be enabled ( page 26).
 The NAT function of your SE680 WiMAX is disabled. This means that the functions
Port Forwarding ( page 27) and Exposed Host ( page 28) are not available.
If necessary you may have to protect your network components against unwelcome
access from the Internet by appropriate means (e.g. firewall software).
24
Advanced Settings
Configuring Internet access
If you have configured the SE680 WiMAX using the Basic Setup Wizard, you have also
configured your Internet access. You can check or change these settings in the Internet menu.
This menu also offers you a wide range of possibilities for setting up security settings
and limiting access to the Internet as well as for providing your own services on the
Internet.
You can carry out the following via the Internet menu:
Internet Connection
Check and edit the Internet connection of the SE680
WiMAX (for further information see below),
DNS Servers
Make DNS server settings (page 26),
Firewall
Protect the network against hacker attacks ( page 26),
Port Forwarding
Provide your own services on the Internet (page 27),
Exposed Host
Opening the firewall for a selected PC (page 28).
Setting up the Internet Connection
You can set up or change the configuration of your Internet connection in this screen.
All the settings you make here must coincide with the features your Internet service provider makes available to you. Incorrect information can lead to problems with your Internet connection.
 Open the Advanced Settings tab and on the Internet menu select Internet Con-
nection.
 Enter the data you have been given by your service provider.
 Select the Protocol used for Internet access.
– PPPoE
– Static
– Obtain automatically
 Apply the default settings for the other parameters unless your service provider has
given you other data.
Connection mode
For a PPPoE connection (Point-to-Point over Ethernet), specify the Connection
mode:
Always on
This gives the users in your network a constantly active Internet connection.
Only choose this setting if your Internet tariff is not time-dependent.
If necessary you can terminate the Internet connection manually ( page 19).
25
Advanced Settings
Connect on demand
The Internet connection is only established if an application, e.g. an Internet
browser or an e-mail program, requests it.
PPPoE pass-through
If you activate the PPPoE pass-through function, a PC in the network can connect to
the Internet via its own connection ID. The router puts this connection through.
Setting up DNS servers
DNS (Domain Name System) is a decentralised database on the Internet which allocates clearly understandable Internet names (domains) to the actual addresses of PCs
and services (e.g. IP addresses). The DNS servers required for access to this database
are normally provided by your provider and do not have to be set up specially. But if
necessary you can change them here.
 Open the Advanced Settings tab and on the Internet menu select DNS Servers.
 Activate the Use custom DNS servers function and enter the IP addresses for your
Preferred DNS server and the Alternate DNS server.
Enabling or disabling the firewall
Your SE680 WiMAX comes with an integrated firewall, which protects your device and
network against unauthorised access from the Internet. If the firewall is enabled, your
device can identify certain events, e.g. suspicious incoming data packets from the Internet, as attacks and avert them (hacker defence). Your device’s firewall is enabled by
default.
We urgently recommend that you leave the firewall of your SE680
WiMAX enabled, otherwise your network will no longer be protected
against hacker attacks from the Internet.
If you still want to disable the firewall:
 Open the Advanced Settings tab and on the Internet menu select Firewall.
 Disable the firewall.
This function is not available in Bridge operating mode, see "Configuring
Internet access" on page 25.
26
PCs in your network should be protected by a separate firewall. You can
set up protection against DoS (Denial of Service) attacks in Bridge mode
via the local network configuration, see "LAN configuration" on page 29.
Advanced Settings
Port Forwarding
The SE680 WiMAX comes with the NAT (Network Address Translation) function, which
is always activated in Router operating mode. With address mapping, multiple users in
the local network can access the Internet via the public IP address. All the local IP
addresses are assigned to the router's public IP address by default. All IP addresses
of PCs in the local network are converted to the router's public IP address when
accessing the Internet.
Most Internet applications can be executed behind the NAT firewall without any problems. However, some applications - such as Internet games - require users in the Internet to send requests to users in the local network so that the players can communicate
with each other. Sometimes these applications also require several ports to communicate through. Such applications do not work if NAT is active.
Using port forwarding (the forwarding of requests to particular ports) the router is forced
to send requests from the Internet for a certain service, for example a game, to the
appropriate port(s) on the PC on which the game is running. If you configure Port Forwarding, the SE680 WiMAX outwardly assumes the role of the server. It receives
requests from remote users under its public IP address and automatically redirects
them to local PCs. The private IP addresses of the servers on the local network remain
protected.
Internet services are addressed via defined port numbers. The SE680 WiMAX needs
a mapping table of the port numbers to redirect the service requests to the servers that
actually provide the service. Port Forwarding has to be configured for this purpose.
 Open the Advanced Settings tab and on the Internet menu select Port Forward-
ing.
 Define the list of services for which you want requests from the Internet to be for-
warded.
Important services are already included in the Predefined applications selection field.
The list can hold up to 16 entries.
The IP addresses of the PCs for which you set up port forwarding must
remain unchanged. If the IP addresses of the PCs are assigned via the
DHCP server of the SE680 WiMAX, you must select the option Never
expires as the Lease time when configuring the DHCP server or assign
static IP addresses to the PCs, see "Configuring the DHCP server" on
page 29.
This function is not available in Bridge operating mode, see "Configuring
Internet access" on page 25.
27
Advanced Settings
Opening the firewall for a selected PC (Exposed Host)
You can set up a client in your local network to be a so-called "exposed host". Your
device will then forward all incoming requests from the Internet to this client, with the
exception of requests to the port numbers already defined via port forwarding. You can
then, for example, operate your own Web server on one of the clients in your local network and make it accessible to Internet users.
As the exposed host, the local client is directly visible to the Internet and therefore particularly vulnerable to attacks (e.g. hacker attacks). Only activate this function if it is
absolutely necessary (e.g. to operate a Web server) and other functions (e.g. port forwarding) are not adequate. In this case you should take appropriate measures for the
clients concerned.
 Open the Advanced Settings tab and on the Internet menu select Exposed Host.
 Define the list of PCs you want to set up as exposed hosts.
 Activate a PC which you want to function as the current exposed host. Only one PC
at a time can be selected.
28
The IP addresses of the PCs you want to set up as exposed hosts must
remain unchanged. If the IP addresses of the PCs are assigned via the
DHCP server of the SE680 WiMAX, you must select the option Never
expires as the Lease time when configuring the DHCP server or assign
static IP addresses to the PCs, see "Configuring the DHCP server" on
page 29.
This function is not available in Bridge operating mode, see "Configuring
Internet access" on page 25.
Advanced Settings
LAN configuration
With the help of the LAN configuration you can change the preset values for the computer name and the private IP address for your SE680 WiMAX and configure the integrated DHCP server.
 Open the Advanced Settings tab and select Local Network.
The preset IP address is 192.168.2.1. This is the private IP address of the SE680
WiMAX. This is the address under which the device can be reached in the local network. It can be freely assigned from the block of available addresses. The IP address
under which the SE680 WiMAX can be reached from outside is assigned by the Internet service provider. The default Subnet mask for the local network administered by the
SE680 WiMAX is 255.255.255.0.
Please note which subnet mask is set when assigning the IP address. The preset subnet mask defines the first three parts of the IP address which must be identical for all
network components (including routers).
We recommend that you use an address from a block that is reserved for private use.
This address block is 192.168.1.1 to 192.168.255.254.
Configuring the DHCP server
The SE680 WiMAX has a DHCP server for which the factory setting is active. Consequently, the IP addresses of the PCs are automatically assigned by the SE680 WiMAX.
 If the DHCP server for the SE680 WiMAX is activated, you can con-
figure the network setting on the PC so that the option Obtain an IP
address automatically is set up.
 If you deactivate the DHCP server, you will have to assign a static IP
address for the PCs that use the network settings.
For more information see the document “Configuring the local area network” on the CD.
 If the DHCP server is active, you can define a Lease time. The lease time indicates
how long the client may use the allocated IP configuration.
Note:
If you select Never expires, the IP addresses are never changed. Activate this
option if you want to make NAT or firewall settings using the IP addresses of the
PCs; otherwise you have to assign static IP addresses to these PCs.
 Define the range of IP addresses the SE680 WiMAX should use to automatically
assign IP addresses to the PCs. Define the Start IP and the End IP.
29
WiMAX configuration
Assigning static IP addresses to individual PCs
Even if you have activated the DHCP server, you can still assign a static IP address to
individual PCs (e.g. when setting up these PCs for NAT functions).
 Enter the MAC address of the PC to which you want to assign a static IP address
and the IP address you wish to assign to the PC.
Configuring the local network in Bridge operating mode
In Bridge operating mode ( page 24) the SE680 WiMAX DHCP server is deactivated.
The network components get their IP addresses from a DHCP server in the public network.
Ageing time for When a PC in the network is accessed, your SE680 WiMAX writes the
MAC table
MAC address and port number in a MAC table to speed up further
accesses. The entry in the MAC table is deleted after a fixed time. If
necessary you can change this value via the MAC table ageing time
parameter.
Protection
against DoS
attacks
DoS (Denial of Service) attacks are attacks on a system in the network to make its services unusable. This is basically done by overloading the system by constantly sending requests. In Bridge mode,
the SE680 WiMAX provides protection against DoS attacks, which
you can enable or disable via the activate DOS protection parameter.
WiMAX configuration
On this page you enter the data for authentication of your device on the WiMAX base
station. You will need the access data supplied by your WiMAX operator for this.
If you have executed the Basic Setup Wizard, you will already have entered these
details there. If necessary you can change them here.
 Open the Advanced Settings tab and select WiMAX configuration from the
menu.
 Select Authentication, if authentication is required by your WiMAX operator and
enter or change the required access data.
30
Administration
Administration
The user interface Administration menu includes several helpful functions for administering your SE680 WiMAX.
System Password
Changes the system password (page 31)
Factory Reset
Reset the SE680 WiMAX to the factory settings (page 32)
Restart
Reboots the device (page 33)
Firmware Update
Updates firmware (page 33)
Depending on the pre-configuration of your device some of the menu
entries and configuration possibilities might be missing in your device.
System password
The system password is the password for configuring your SE680 WiMAX and is
requested when you open the configuration pages, see "Launching the user interface"
on page 15.
If the device came from your provider with a preset system password, you can change
this password here.
The system password protects your SE680 WiMAX and your local network from unauthorised access. For this reason, it is important to set up
a password and change the default password.
 Open the Advanced Settings tab and on the Administration menu select System
Password.
Features of a secure password
A password should be difficult for unauthorised users to work out. Note the following
points when choosing a password:
 The more characters a password has, the more secure it is.
 Choose a series of characters that is as varied as possible (not AAAA, 0000) and





alternate between letters and numbers.
Do not use any term that could be found in a dictionary.
Do not use sequential characters (not 123456, abcd) and no recognisable system
(not 1a2b3c).
Never use a password several times for different applications.
Never save a password on the PC. Instead, make a note of it and store it in a secure
place.
Change your passwords regularly.
31
Restoring factory settings
Changing the password
 Enter the current password in the Current password field. If no default system
password has been set, leave this field empty.
 Enter a new password in the New password field.
– Select any series of characters with a minimum length of 4 and a maximum
length of 20 characters. You can use the following characters: A–Z, a–z, 0–9 as
well as the following special characters: ! “ # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \
] ^ _ { | } ~.
– Note down your new password on a sheet of paper and store it in secure place.
 Enter your new password in the Confirm new password field again. This entry is
case-sensitive.
The new password can only be activated if both entries match. This detects typing
errors when the password is entered.
 Finally, click Ok to accept your change and to activate the new password.
The new password is valid immediately for each instance the configuration is called
up.
The configuration of the SE680 WiMAX cannot be accessed if you
do not enter a valid password. In this case, you must restore all the factory settings of the SE680 WiMAX modem.
Restoring factory settings
You can reset the SE680 WiMAX to the factory settings. You should do this before making the device available to others or exchanging it through the dealer. Otherwise unauthorised users may use the Internet access data at your expense.
 Open the Advanced Settings tab and on the Administration menu select Factory
reset.
 Click Ok.
A window will appear prompting you to confirm the procedure.
32
Please remember that when the device is fully reset, all the configuration
settings are returned to the factory settings. This means that you will
have to completely reconfigure the SE680 WiMAX.
Updating the firmware
Restart
If the SE680 WiMAX is not operating properly, you can reboot it. It should then be ready
for use again.
 Open the Advanced Settings tab and on the Administration menu select
Restart.
 Click Ok to reboot the device.
A window will appear prompting you to confirm the procedure.
Updating the firmware
If your WiMAX provider provides a new downloadable firmware version for your SE680
WiMAX with new functions or to fix errors, you can update your device quickly and easily.
 First download the relevant firmware file from the Internet and save it on your PC.
Read the information provided carefully.
Only update the firmware if there is a new version of the firmware that is
currently installed on your device on the Internet. The firmware version
currently installed is shown under Active image version.
 Open the Advanced Settings tab and on the Administration menu select
Firmware Update.
 Enter the path and file name of the firmware file to be installed or click Browse to
select a file on your PC.
 Click Ok to start the firmware update.
Do not disconnect your SE680 WiMAX from the PC or the power supply
during the firmware update, as this could damage the device. It may take
up to five minutes before the device is ready for use again.
33
Status
Status
You can check the status of your SE680 WiMAX with the pages in the Status menu.
The menu is divided into several individual pages opened by clicking the entries in the
menu area. To help with orientation, in the following sections the path is placed first so
that you can quickly find the status messages described.
For example, with the following address you can open the settings of your LAN:
Status > Local Network.
If you have problems, before contacting your provider or customer
service, check the status of your SE680 WiMAX.
When looking for the fault, your provider or customer service will need
some details that you will find on the status pages.
You will find the most important status information summarised on the homepage.
For detailed information, click an entry in the submenu.
Information on the Status homepage
Connection status
The status of the radio connection with the WiMAX network is
displayed as follows:
 connected = The SE680 WiMAX has established a radio
connection with a WiMAX network. You will see the connection duration in brackets and in the format ddd:hh:mm:ss
(d=days, h=hours, m=minutes, s=seconds).
 disconnected = The SE680 WiMAX is trying to establish a
connection with a WiMAX network.
IP address
For an existing Internet connection only:
Displays the IP address used by the SE680 WiMAX on the Internet.
IP address
IP address used by the SE680 WiMAX in your local network.
DHCP server
Displays whether the DHCP server of your SE680 WiMAX is
activated. As DHCP server, your SE680 WiMAX assigns an IP
address to all the PCs in the network. DHCP must be activated
on a PC for the PC to receive an IP address from the DHCP
server. For more information see the document "Configuring the
local area network" on the product CD.
System time
Displays the current date and time. The date and time are
transmitted to your SE680 WiMAX from the WiMAX network.
Operating mode
Role played by your SE680 WiMAX during connection setup to
the Internet (Router or Bridge).
Firmware version
Version number of the currently installed device software. You
will also need to give your provider this number.
 If necessary, click the Refresh button to refresh the data in the status display.
34
Internet
Internet
Status > Internet
The connection settings for your SE680 WiMAX are displayed in the Internet submenu.
Connection status
The status of the radio connection with the WiMAX network
is displayed as follows:
 connected = The SE680 WiMAX has established a
radio connection with a WiMAX network. You will see the
connection duration in brackets and in the format
ddd:hh:mm:ss (d=days, h=hours, m=minutes, s=seconds).
 disconnected = The SE680 WiMAX is trying to establish a connection with a WiMAX network.
IP address
Subnet mask
For an existing Internet connection only:
Displays the public IP address and subnet mask via which
your SE680 WiMAX establishes the connection with the
Internet.
MAC address
The MAC address uniquely identifies a network component
within a network, in this case the public MAC address of
your SE680 WiMAX within the WiMAX network you use.
Default gateway
For an existing Internet connection only:
Displays the gateway the SE680 WiMAX uses for connecting to the Internet.
DHCP server
IP address of the DHCP server with which the SE680
WiMAX is connected. While the SE680 WiMAX has not
been assigned an IP address by the WiMAX network, the
field stays empty.
Preferred DNS server
Alternate DNS server
For an existing Internet connection only:
Displays the domain name server the SE680 WiMAX uses
to convert names to IP addresses.
Address Translation
(NAT)
Displays whether NAT mode is activated on your SE680
WiMAX. NAT converts the internal IP addresses of the PCs
in your network to public IP addresses. This maintains the
confidentiality of your internal IP addresses.
 If necessary, click the Refresh button to refresh the data in the status display.
35
Device status
Local network LAN
Status > Local Network
The configuration of the local network is displayed in the Local Network submenu.
IP address
IP address used by the SE680 WiMAX in your local network.
Default: 192.168.2.1
Subnet mask
Subnet mask of your local network. Default: 255.255.255.0
MAC address
The MAC address uniquely identifies a network component
within a network, in this case the local MAC address of your
SE680 WiMAX within your local network.
DHCP server
Displays whether the DHCP server of your SE680 WiMAX is
activated. As DHCP server, your SE680 WiMAX assigns an IP
address to all the PCs in the network. If the DHCP server is
activated, you will see the network subscribers that have
received your IP address from the DHCP server in the DHCP
clients field. DHCP must be activated on a PC for the PC to
receive an IP address from the DHCP server. For more information see the document "Configuring the local area network"
on the product CD.
 If necessary, click the Refresh button to refresh the data in the status display.
Device status
Status > Device Status
The device status of your SE680 WiMAX is displayed in the Device Status submenu.
System uptime
Operating time of your SE680 WiMAX since it was last
restarted. The operating time is given in the format
ddd:hh:mm:ss (d=days, h=hours, m=minutes, s=seconds).
System time
Displays the current date and time. This information is transmitted to your SE680 WiMAX by the WiMAX network.
Operating Mode
Role played by your SE680 WiMAX during connection setup to
the Internet (Router or Bridge).
Device temperature
Current device temperature inside your SE680 WiMAX. In the
event of overheating, the SE680 WiMAX switches off.
System Log
Error protocol in which you will find information about problems.
 If necessary, click the Refresh button to refresh the data in the status display.
36
Device status
Radio status
Status > Radio Status
Information about the radio connection to the WiMAX network is displayed in the Radio
Status submenu.
Connected to a base station
Indicates whether or not your SE680 WiMAX is connected to a base station.
Base station ID
ID number of the base station to which the device is connected.
MAC state
Status of the connection setup to the base station. The information shown here is
only intended for technically experienced users. Under Connected to a base station is shown whether a connection to a base station exists.
Authentication
Indicates whether an authentication method is used for the WiMAX connection.
Protocol
Protocol used for authentication.
Received power level
Receive level from the WiMAX base station. Values in the range -70 dBm to 10 dBm are considered optimum. You can ensure this by optimising the antenna
direction.
Transmitted power level
Current transmission power.
Carrier to interference and noise ratio
Measurement of the reception quality of the base station. The higher the value, the
better the quality of the data transfer to the base station.
Centre frequency of current uplink channel
Currently used uplink frequency. The reading changes frequently during the measurement.
Centre frequency of current downlink channel
Currently used downlink frequency.
Current channel bandwidth
Currently used bandwidth.
Radio port uplink current average throughput
Average approximate uplink throughput in one second, moving average
(5 samples).
Radio port downlink current average throughput
Average approximate downlink throughput in one second, moving average
(5 samples).
37
Device status
Current uplink modulation scheme
Currently used uplink modulation type.
Current downlink modulation scheme
Currently used downlink modulation type.
 If necessary, click the Refresh button to refresh the data in the status display.
38
Using the SE680 WiMAX
Using the SE680 WiMAX
When you have finished configuring your SE680 WiMAX modem, use it to surf the
Internet, send e-mails etc.
As soon as you attempt to access the Internet with a PC connected to the SE680
WiMAX modem (for example, by opening the Web browser and calling up an Internet
site, or by starting your e-mail program and retrieving e-mails), your SE680 WiMAX
modem automatically establishes a connection to the Internet or uses the permanent
Internet connection. Whether the connection needs to be established or is permanently
available depends on your provider's default settings.
39
Appendix
Appendix
Troubleshooting
In the case of network problems troubleshooting may be difficult, as miscellaneous network parameters may be affected. This section only describes problems which are
associated with the SE680 WiMAX modem.
Symptom
Possible cause and solutions
No LED does light up.
The SE680 WiMAX modem is not connected to the
mains.
 Check if the indoor unit is connected correctly.
The CONNECT LED does
not light up.
 Check if the power socket is live.
The SE680 WiMAX modem is not registered to a base
station.
 Check the cable connections. If necessary, charge
The SE680 WiMAX modem
switches itself off.
a qualified electrician to check the installation.
The SE680 WiMAX modem is not ready for use.
The device may be too hot. In this case, the integrated
overheating protector prevents the SE680 WiMAX
modem from being damaged. If the temperature rises,
the SE680 WiMAX automatically reduces data transfer
to a minimum. When the temperature exceeds the critical value, the SE680 WiMAX modem switches itself
off.
 Wait until the SE680 WiMAX modem has cooled
down.
 Check the device status of your SE680 WiMAX
modem, see chapter "Device status" on page 36.
 If the SE680 WiMAX modem does not work after
the device has been restarted, please contact your
provider/service technician.
40
Troubleshooting
Symptom
Possible cause and solutions
The SE680 WiMAX modem
can not be reached via LAN
(Ethernet).
 If you operate the SE680 WiMAX modem in bridge
mode, first check the following:
1. In bridge mode the PC must be connected directly
to the SE680 WiMAX indoor unit LAN port.
2. To configure the SE680 WiMAX modem the PC
must have a static IP address assigned.
 If you operate the SE680 WiMAX modem in router
mode, precede as follows:
1. Check all cable connections.
2. Enter a ping command to your own computer using ping 127.0.0.1, see "Checking the connection to the SE680 WiMAX" on page 43. If an error
is reported, reinstall the TCP/IP network protocol.
3. Enter a ping command to the SE680 WiMAX modem using ping 192.168.2.1 (if you did not
change the IP address). If errors are reported, ensure that the digits in the first three address parts
of the PCs IP address are the same as in the IP address of the SE680 WiMAX modem. If not all test
packets sent will be reported as faulty, change the
Ethernet cables. They may be faulty.
4. Read the document "Configuring the local area
network" on product CD.
You forgot the system pass-  Reset the SE680 WiMAX to the factory settings.
word.
No connection to the config-  Check the connection to your SE680 WiMAX
uration environment is posmodem, see page 43.
sible.
41
Troubleshooting
Other faults and problems
You are using a firewall on the PC that prevents access to the SE680 WiMAX
modem
Test this, if necessary, by briefly switching off the firewall. If access is possible, configure the firewall. For details, refer to the user guide for your firewall.
You have forgotten the system password
If you have assigned your own system password or changed and forgotten it, you need
to return your SE680 WiMAX modem to the factory settings.
Power failure
No data will be lost.
Before contacting customer service or your provider
 First exclude all the faults listed in this section.
 Have the documentation supplied by your provider ready.
 If you can open the configuration program in the Web browser, click on the Status
tab.
 Note the number in the Firmware version field. This is the number of the currently
installed device software.
 Open the Local Network submenu and note the entry consisting of numbers and
letters in the MAC address field. The MAC address is used for the globally unique
identification of your device.
 Leave the PC switched on and the configuration program open when you phone
customer service or your provider. They might need still more information, which
you will find on the status pages.
42
Troubleshooting
Checking the connection to the SE680 WiMAX
You can check whether the PC is correctly connected to the SE680 WiMAX modem.
This can be done as follows:
 Open the command prompt on the PC:
– Click on Start > Run.
– Enter cmd in the input field and click on OK.
The Command prompt window opens.
 Check whether the SE680 WiMAX modem responds with the ping command. Enter
ping 192.168.2.1 and press Enter.
The PC now sends some test packets via this connection and checks whether the connection partner responds. The connection partner may respond in the following ways:
 Reply from the IP address of your SE680 WiMAX modem; statistics about the
connection are presented. If you receive these statistics, the connection to the
device is OK.
 The request exceeds the time limit; it was not possible either to send or receive
any packets. There is no physical connection between the PC and your SE680
WiMAX modem. Check the following points:
– Are the Ethernet cables both between the SE680 WiMAX modem and the indoor
unit as well as between the indoor unit and the PC properly connected?
The OUT and IN LEDs on the indoor unit must light up ( page 9).
– Has TCP/IP been properly configured on your PC?
If the SE680 WiMAX modem has the IP address 192.168.2.1, your PC's IP
address must be between 192.168.2.2 and 192.168.2.254. The subnet mask
must be 255.255.255.0.
To find out the IP address of your PC, enter ipconfig in the command prompt.
If the SE680 WiMAX modem has not responded successfully to the ping command,
you need to adjust the network settings on the PC. To find out how to do this, please
read the document "Configuring the local area network" on the product CD.
If the SE680 WiMAX modem has responded successfully to the ping command, the
network is configured correctly. If it is not possible to access the configuration program
of your SE680 WiMAX modem, check and change the settings in your Web browser.
To find out how to do this, please read the next chapter.
43
Troubleshooting
Configuring the Web browser
If you are using a current Web browser but cannot open the configuration program in
it, check the Web browser settings.
We recommend Microsoft Internet Explorer Version 7.0 or Mozilla
Firefox 3.0 as the Web browser.
 Do not use an HTTP proxy for accessing your SE680 WiMAX modem.
 Popup windows must be enabled for your SE680 WiMAX modem.
The following descriptions relate to Internet Explorer Version 7.0 and Mozilla Firefox
Version 3.0.
Setting up an HTTP proxy
An HTTP proxy is a buffer for Internet pages that have been called up. For example,
once called up, a page can continue to be shown even if you are currently offline. However, this buffer would prevent the configuration pages being read again when you call
up the configuration for your SE680 WiMAX modem; for this reason, your SE680
WiMAX modem can only be configured if the HTTP proxy is not being used for local
pages.
Check the HTTP proxy in the Web browser you wish to use for the configuration.
Internet Explorer 7.0:
 Open Internet Explorer.
 Click on Tools and then on Internet Options.
 Open the Connections tab.
 Click on LAN settings.
 If the option Use proxy server for LAN is activated in the Proxy server area, acti-
vate the selection field Circumvent proxy server for local addresses. If the
option Use proxy server for LAN is not activated, you do not need to make any
settings.
 Click on OK and then OK again to close the Internet Options window.
Firefox 3.0:
 Open Firefox.
 Click on Tools and then on Settings.
 Click on Advanced.
 Open the Network tab and click on Settings in the Connection area.
 Select either No proxy or Manual proxy configuration. If you have chosen Man-
ual proxy configuration, in the No proxy for: field, enter the IP block in which the
IP address of your SE680 WiMAX modem is found: 192.168.2.0/24
 Click on OK and then OK again to close the Settings window.
44
Troubleshooting
Allowing pop-up windows
Pop-up windows are small windows that are opened either as the result of an action or
automatically. The device software for your SE680 WiMAX modem uses pop-up windows to display the online Help, for example.
Many Internet sites, however, call up distracting pop-up windows for effective advertisement placement, for example, without detracting from the layout of the site itself. To prevent these pop-up windows from opening, current Web browsers offer pop-up blockers.
If necessary, you can configure the pop-up blocker to display desirable pop-up windows
and to block undesirable windows.
If you are using a different pop-up blocker, configure it to allow pop-up
windows for the IP address 192.168.2.1.
Internet Explorer 7.0:
 Open Internet Explorer.
 Click on Tools and then on Pop-up Blocker and choose Pop-up Blocker Set-
tings.
 Enter the IP address of your SE680 WiMAX modem as the Website address:
192.168.2.1
 Click on the Add button.
 Click on Close to apply the settings.
Firefox 3.0:
 Open Firefox.
 Click on Tools and then on Settings.
 Click on Content.
 If the Block pop-up windows check box is activated, click to its right on Excep-
tions.
 Enter the IP address of your SE680 WiMAX modem as the Website address:
192.168.2.1
 Click on the Allow button.
 Click on Close and on OK to apply the settings.
45
Troubleshooting
Specifications
Model
SE680 WiMAX
Dimensions
Outdoor Modem:
approx. 228.5 x 208 x 101 mm
Indoor unit:
approx. 140 x 65 x 36 mm
Operating temperature
Outdoor Modem:
Indoor unit:
Network interface
–40 °C to +60 °C
0 °C to +40 °C
1 Ethernet 10/100BaseT (RJ45, LAN)
Frequency
2.3–2.4 / 2.5–2.7 / 3.4–3.6 GHz
Output power
up to 26 dBm at QAM-16
Power consumption
3-6 W on DC input depending on operational state
Bandwidth
optional: 3.5 / 5.0 / 7.0 / 8,75 or 10.0 MHz
Type of transmission
TDD
Modulation technique
SOFDMA 512/1024
Subcarrier modulation
QPSK, 16/64 QAM in up- and downlink
Antenna type
2 internal antennas (2xRX, 1xTX) for MIMO Matrix
A & B; Type DN1 (EN 302 326-3 V1.2.2)
Antenna gain
10 / 11 dBi (2.6 / 3.5 GHz)
Mains adapter
Input: 100–240 V AC, Power over Ethernet (PoE)
Putting into service
This device is intended for use in the country indicated on the device's label.
The device is operated under a single licence, which is held by your service provider.
Contact your service provider regarding licensing before you put the device into
service.
Please observe the legal provisions and local restrictions when putting the
device into service. Please ask your service provider for further information.
46
WEEE
CE declaration
This device is intended for use with WiMAX base stations.
We, Sagemcom Broadband SAS, declare that this device meets the essential requirements and other relevant regulations laid down in Directive 1999/5/EC. National laws
and regulations must be considered before putting the device into service.
A copy of the 1999/5/EC declaration of conformity is available at this Internet address:
http://support.sagemcom.com
WEEE
All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
This crossed-out wheeled bin symbol on the product means the product is
covered by the European Directive 2002/96/EC.
The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health.
It is a precondition for reuse and recycling of used electrical and electronic
equipment.
For more detailed information about disposal of your old appliance, please
contact your local council refuse centre or the original supplier of the product.
47
WEEE
Open Source Software used in the product
The SE680 WiMAX contains, among other things, Open Source Software, licensed
under an Open Source Software License and developed by third parties. These Open
Source Software files are protected by copyright. Your rights to use the Open Source
Software beyond the mere execution of the Sagemcom Broadband SAS program, is
governed by the relevant Open Source Software license conditions.
Your compliance with those license conditions will entitle you to use the Open Source
Software as foreseen in the relevant license. In the event of conflicts between Sagemcom Broadband SAS license conditions and the Open Source Software license conditions, the Open Source Software conditions shall prevail with respect to the Open
Source Software portions of the software. The Open Source Software is licensed royalty-free (i.e., no fees are charged for exercising the licensed rights, whereas fees may
be charged for reimbursement of costs incurred by Sagemcom Broadband SAS).The
license conditions can be found in the following chapters. In addition some of the
license texts can be downloaded from:
 The BSD License is available on the Internet at:
http://www.freebsd.org/copyright/license.html
 The OpenSSL license is available on the Internet at:
http://www.openssl.org/source/license.html
 The zlib license is available on the Internet at:
http://www.zlib.net/zlib_license.html
 Boost Software License
http://www.boost.org/LICENSE_1_0.txt
Warranty regarding further use of the Open Source Software
Sagemcom Broadband SAS provides no warranty for the Open Source Software programs contained in this device, if such programs are used in any manner other than the
program execution intended by Sagemcom Broadband SAS. The licenses listed below
define the warranty, if any, from the authors or licensors of the Open Source Software.
Sagemcom Broadband SAS specifically disclaims any warranties for defects caused
by altering any Open Source Software program or the product's configuration. You
have no warranty claims against Sagemcom Broadband SAS in the event that the
Open Source Software infringes the intellectual property rights of a third party.
48
WEEE
Open Source Software used
Open Source Software Component
wpa_supplicant
djbbns
zlib
boost lib
expat
openSSL
sybyx
AES and combined encryption /
authentication modes
License
BSD-license
public domain
Zlib license
Boost Software License
expat license
OpenSSL License, SSLeay License
proprietary
proprietary
Acknowledgements
WPA Supplicant:
Copyright (c) 2003-2007, Jouni Malinen  and contributors
All Rights Reserved.
OpenSSL:
This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)
This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com)
Zlib:
This product includes software developed by Jean-loup Gailly and Mark Adler
sybyx:
This product uses Streaming WBXML Parser developed by MediaSite Inc Research
and Development Group.
49
WEEE
Open Source Software Licenses
WPA-Supplicant
License: BSD
WPA Supplicant
==============
Copyright (c) 2003-2007, Jouni Malinen  and contributors
All Rights Reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name(s) of the above-listed copyright holder(s) nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
OpenSSL
This is a copy of the current LICENSE file inside the CVS repository.
LICENSE ISSUES
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the
OpenSSL License and the original SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both licenses are BSD-style Open
Source licenses. In case of any license issues related to openSSL please contact
openssl-core@openssl.org.
50
WEEE
OpenSSL License
Copyright (c) 1998-2005 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display
the following acknowledgment: "This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse
or promote products derived from this software without prior written permission. For
written permission, please contact openssl-core@openssl.org.
5. Products derived from this software may not be called "OpenSSL"nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment:
This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit (http://www.openssl.org/)
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY
EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
================================================================
This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com). This product includes software written by Tim Hudson
(tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).
The implementation was written so as to conform with Netscapes SSL.
51
WEEE
This library is free for commercial and non-commercial use as long as the following
conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL
documentation included with this distribution is covered by the same copyright terms
except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young's, and as such any Copyright notices in the code are not
to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual
message at program startup or in documentation (online or textual) provided with the
package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display
the following acknowledgement: "This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)" The word 'cryptographic' can be left out if
the rouines from the library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: "This product includes software written by Tim Hudson (tjh@cryptsoft.com)"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically available version or derivative of
this code cannot be changed. i.e. this code cannot simply be copied and put under
another distribution licence [including the GNU Public Licence.]
Zlib:
'zlib' general purpose compression library version 1.1.4, March 11th, 2002
Copyright (C) 1995-2002 Jean-loup Gailly and Mark Adler
This software is provided 'as-is', without any express or implied warranty. In no event
will the authors be held liable for any damages arising from the use of this software.
52
WEEE
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following
restrictions:
1. The origin of this software must not be misrepresented ; you must not claim that you
wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly
jloup@gzip.org
Mark Adler
madler@alumni.caltech.edu
The data format used by the zlib library is described by RFCs (Request for Comments)
1950 to 1952 in the files ftp://ds.internic.net/rfc/rfc1950.txt (zlib format), rfc1951.txt
(deflate format) and rfc1952.txt (gzip format).
This manual is converted from zlib.h by piaip
Visit http://ftp.cdrom.com/pub/infozip/zlib/ for the official zlib web page.
Boost lib
Boost Software License - Version 1.0 - August 17th, 2003
Permission is hereby granted, free of charge, to any person or organization obtaining
a copy of the software and accompanying documentation covered by this license (the
"Software") to use, reproduce, display, distribute,execute, and transmit the Software,
and to prepare derivative works of theSoftware, and to permit third-parties to whom the
Software is furnished todo so, all subject to the following:
The copyright notices in the Software and this entire statement, including the above
license grant, this restriction and the following disclaimer, must be included in all copies
of the Software, in whole or in part, and all derivative works of the Software, unless such
copies or derivative works are solely in the form of machine-executable object code
generated by a source language processor.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NONINFRINGEMENT. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR ANYONE
DISTRIBUTING THE SOFTWARE BE LIABLE FOR ANY DAMAGES OR OTHER LIABILITY, WHETHER IN CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT
OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
53
WEEE
expat
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark
Cooper
Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or
substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND ONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION
OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
sybyx
http://sourceforge.net/projects/sybyx/
Copyright (c) 2001 MediaSite Inc Research and Development Group.
All rights reserved.
Copyright (c) 2002 Interactive Intelligence, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The end-user documentation included with the redistribution, if any, must include
the following acknowledgment:
"This product uses Streaming WBXML Parser developed by MediaSite Inc Research and Development Group"
Alternately, this acknowledgment may appear in the software itself, if and wherever
such third-party acknowledgments normally appear.
THIS SOFTWARE IS PROVIDED "AS IS"' AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL MEDIASITE INC OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
54
WEEE
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
================================================================
Created by: Dima Skvortsov
Modified by: Chris Hubbard
AES and Combined Encryption/Authentication Modes
(http://gladman.plushost.co.uk/oldsite/AES/index.php)
http://gladman.plushost.co.uk/oldsite/AES/aes-src-29-04-09.zip
http://gladman.plushost.co.uk/oldsite/AES/aes-modes-src-23-07-09.zip
----------------------------------------------------------------------------------------------------------------Copyright (c) 1998-2008, Brian Gladman, Worcester, UK. All rights reserved.
LICENSE TERMS
The redistribution and use of this software (with or without changes) is allowed without
the payment of fees or royalties provided that:
1. source code distributions include the above copyright notice, this list of conditions
and the following disclaimer;
2. binary distributions include the above copyright notice, this list of conditions and the
following disclaimer in their documentation;
3. the name of the copyright holder is not used to endorse products built using this
software without specific written permission.
DISCLAIMER
This software is provided 'as is' with no explicit or implied warranties in respect of its
properties, including, but not limited to, correctness and/or fitness for purpose.
---------------------------------------------------------------------------------------------------------------Issue Date: 21/07/2009
55
Glossary
Glossary
Address Translation (NAT)
Network Address Translation. NAT is a method for converting IP addresses (mainly private IP addresses) in a network to one or more public IP addresses on the Internet.
With NAT, several network components in a LAN can share a public IP address to connect to the Internet. The network components of the local network are hidden behind
the IP address registered on the Internet. NAT is often used as part of the firewall in a
network because of this security function.
Bridge
A bridge connects several network segments to form a joint network, e.g. to make a
TCP/IP network. The segments can have different physical characteristics, e.g. different linking such as Ethernet and wireless LANs. Local networks can be expanded by
linking individual segments via bridges.
dB
Decibel (a tenth of a Bel). Logarithmic unit of measurement for ratios between two currents, voltages, sound levels or powers. In order to depict large value differences
clearly and graphically, these are given in dB; e.g. 60 dB corresponds to the factor 1000
relative to the voltage drops.
dBm
Decibel milliwatt. Power level in decibels relative to 1 milliwatt.
DHCP
Dynamic Host Configuration Protocol. DHCP handles the automatic assignment of IP
addresses to network components.
DHCP was developed because in large networks – especially the Internet – the defining of IP addresses is very complex as subscribers frequently move, drop out or new
ones join. A DHCP server automatically assigns the connected network components
(DHCP clients) dynamic IP addresses from a defined IP pool range, thus saving a great
deal of configuration work. In addition, the address blocks can be used more effectively:
since not all subscribers are on the network at the same time, the same IP address can
be assigned to different network components in succession as and when required.
DHCP server
There is a DHCP integrated into the SE680 WiMAX modem that automatically assigns
IP addresses to PCs in the local network.
56
Glossary
DNS
Domain Name System. DNS permits the assignment of IP addresses to PC or domain
names that are easier to remember. A DNS server must administer this information for
each local network with an Internet connection. As soon as a page on the Internet is
called up, the Web browser obtains the corresponding IP address from the DNS server
so that it can establish the connection.
On the Internet, the assignment of domain names to IP addresses follows a hierarchical
system. A local PC only knows the address of the local name server. This in turn knows
all the addresses of the PCs in the local network and the superordinated name servers,
which again know addresses and the next superordinated name servers.
Domain name
The domain name is the reference to one or more web servers on the Internet. The
domain name is mapped via the DNS service to the corresponding IP address.
Downlink
Files that your SE680 WiMAX modem receives and forwards to your local network.
DSL
Digital Subscriber Line. DSL is a technique whereby data is transmitted via the conventional phone line. To do this, you require suitable phone lines and special technology to
be set up by a Provider. As these preconditions are not satisfied in all areas, it is not
possible to use DSL in all locations. In order to make use of high-performance Internet
access in these areas as well, technologies such as WiMAX, Wi-Fi or satellite connections are implemented.
Ethernet
Ethernet is a network technology for local networks (LANs) defined by the IEEE as
standard IEEE 802.3. Depending on the network adapter used, the transmission speed
on the Ethernet varies between 10 Mbps and 1 Gbps.
Firewall
Firewalls are used by network operators as protection against unauthorised external
access. This involves a whole bundle of hardware and software actions and technologies that monitor and control the data flow between the private network to be protected
and an unprotected network such as the Internet.
Firmware
Device software. To correct errors or update the device, a new firmware version can be
loaded onto the device's memory (firmware update).
Flat rate
Flat rate is a particular billing system for Internet connections. The Provider charges a
set monthly fee for a certain service package.
57
Glossary
FTP
File Transfer Protocol. Protocol for exchanging files via the Internet. FTP is used, for
example, to make files available for download or to receive files from other users.
Full duplex
Data transmission operating mode in which data can be sent and received at the same
time.
FXS
Foreign Exchange Station. Phone port to which an analogue terminal (phone, fax or
answer machine) can be connected.
Gateway
A gateway connects networks with one another. In contrast to a Router, a gateway is
not dependent on protocol, i.e. it is also able to establish connections between networks with a different architecture (protocols, application interfaces etc.).
Half duplex
Operating mode for data transfer. Only one party can receive or send data at a time.
HTTP
Hypertext Transfer Protocol. Network protocol for the transmission of data, which is
mainly used for transmitting and displaying Internet content.
HTTP proxy
An HTTP proxy is a server that network components use for their Internet traffic. All
requests are sent via the proxy.
Hub
A hub is a central distribution point in a network, to which PCs and other network
devices are connected. The hub forwards received data to all connected PCs. For this
reason, in large networks, a Switch is recommended to ensure that data is only sent to
the PC requesting it.
IEEE
Institute of Electrical and Electronics Engineers. The IEEE is an international body for
defining network standards, especially for standardising LAN technologies, transmission protocols and speeds, and wiring.
58
Glossary
IEEE 802.16
Standard defined by the IEEE for WiMAX. Similarly to other standards in the 802 series
(e.g. 802.3 Ethernet, 802.11 WLAN), the WiMAX standard is one of the standards for
networks. The standard has progressed in accordance with new developments; there
are currently two main versions:
 IEEE 802.16-2004: WiMAX, which specifies the secure location for connection part-
ners.
 IEEE 802.16e-2005: Mobile WiMAX, which enables wireless cells to be exchanged
during data transmission.
IP
Internet Protocol. The protocol is responsible for addressing of subscribers in a network
using IP addresses, and routes data from the sender to the recipient. In doing so, it
decides on the way in which data packets will be forwarded between sender and recipient.
IP address
An IP address is the unique network-wide address of a network component in a network based on the TCP/IP protocol (e.g. in a local network or on the Internet). The IP
address consists of four parts (each of up to three-figure strings of digits from 0–255)
that are separated from one another by full stops (e.g. 192.168.2.1). The IP address is
made up of the network number and the number of the network component. Depending
on the Subnet mask, one, two or three parts form the network number, the remainder
form the network component number. You can find out the IP address of your PC using
the ipconfig command.
There are two different types of IP address:
 Private IP address:
IP address of a network component within a local network.
 Public IP address:
IP address that uses a network component for accessing the Internet.
IP addresses can be assigned manually or automatically:
 Static IP address:
The IP address is manually assigned to a network component and never changes.
 Dynamic IP address:
The IP address is assigned to the network component by a DHCP server. The IP
address of this network component can change each time it registers with a network
or at specific time intervals.
On the Internet, domain names are normally used instead of the IP addresses. DNS is
used to assign domain names to IP addresses.
IPTV
Internet Protocol Television. You receive your provider's television service via the DSL
connection. To do this, you require an IPTV-capable set-top box and the configuration
data of your IPTV provider.
59
Glossary
ISP
Internet Service Provider. See Provider.
LAN
Local Area Network, local network. A local network links network components so that
they can exchange data and share resources. The physical range is restricted to a particular area (a site). A local network can be connected to other local networks or a widearea network (WAN) such as the Internet.
LED
Light Emitting Diode. An LED is an electronic component (semi-conductor) that generates light at low power consumption. LEDs are often used as signal lights for display
and UI elements.
Login
Access to a PC or a service, password e.g. for access to the Internet.
MAC address
Media Access Control. The MAC address is used for the globally unique identification
of a network adapter. It comprises six parts (hexadecimal numbers), e.g. 00-90-96-3400-1A. The MAC address is assigned by the network adapter manufacturer and cannot
be changed.
Mbps
Million bits per second. Specification of the transmission speed in a network.
Network
A network is a group of devices connected in wired or wireless mode so that they can
share resources such as data and peripherals. A general distinction is made between
local networks (LANs) and wide-area networks (WANs).
Network adapter
The network adapter is the hardware device that creates the connection between a network component and a local network. The connection can be wired or wireless. An Ethernet network card is an example of a wired network adapter. A network adapter has a
unique address, the MAC address.
60
Glossary
Network protocol
The network protocol is the standard via which different PCs exchange data in a network. A connection can only be established between PCs in a network if they all use
the same protocol. The TCP/IP network protocol is the most extensive network protocol, which is also used for connections to the Internet. This must be set up on each PC
from which a network connection is to be established.
Port
Data is exchanged between two applications in a network across a port. The port
number addresses an application within a network component. The combination of IP
address/port number uniquely identifies the recipient or sender of a data packet within
a network. Some applications (e.g. Internet services such as HTTP or FTP) work with
fixed port numbers; others are allocated a free port number whenever they need one.
Port forwarding
In port forwarding, the SE680 WiMAX directs data packets from the Internet that are
addressed to a particular Port to the corresponding port of the appropriate network
component. This enables servers within the local network to offer services on the Internet without them needing a public IP address. See also: Virtual server
Protocol
A protocol describes the agreements for communicating on a network. It contains rules
for opening, administering and closing a connection, as well as about data formats,
time frames and handling possible errors. Communications between two applications
require different protocols at various levels, e.g. the TCP/IP protocols for the Internet.
Provider
A provider (Internet Service Provider) offers access to the Internet for a fee.
RJ
Registered Jack. Standardised connection, also known as a modular jack.
Router
A router directs data packets from one local area network (LAN) to another via the fastest route. A router enables the connection between networks of different network technologies and this is performed on the basis of a common protocol. For example, it can
link a local network with WiMAX technology to the Internet.
RSSI
Received Signal Strength Indication. Characteristic value for the signal strength of
radio connections, used by communication devices for the automatic selection of a suitable channel.
Server
A server makes services available to other network components (clients). The term
"server" is often used to refer to a PC. However it can also mean an application that
provides a particular service such as DNS, DHCP or a Web service.
61
Glossary
SMTP
Simple Mail Transfer Protocol. The SMTP protocol is a TCP/IP protocol and regulates
the exchange of electronic post on the Internet. Your Provider provides you with access
to an SMTP server.
Subnet
A subnet divides a network into smaller units.
Subnet mask
The subnet mask determines how many parts of the IP addresses of a network represent the network number and how many parts represent the network component
number.
If the subnet mask in a network is 255.255.255.0, for example, this means that the first
three parts of the IP address make up the network number and only the last part can
be used to assign network component numbers. The first three parts of the IP address
of all network components are in this case always the same.
Switch
A switch is a central distributor in a wired network, which, unlike a hub, provides intelligent distribution of data transfer. The switch only ever forwards a data packet to the
subnet or network component the data packet is intended for. Unnecessary transfer of
data in the network thus avoided.
TAE
Telecommunications connecting unit (German: Telekommunikations-Anschlusseinheit). Connector for connecting analogue telecommunications devices. F for phone, N
for additional devices such as fax or answer machines.
TCP
Transmission Control Protocol. TCP is part of the TCP/IP protocol family. TCP handles
data transport between communication partners (applications). TCP is a sessionbased transmission protocol, i.e. it sets up, monitors and terminates a connection for
transporting data.
TCP/IP
Transmission Control Protocol/Internet Protocol. Protocol family on which the Internet
is based. IP forms the basis of each PC to PC connection. TCP provides applications
with a reliable transmission link in the form of a continuous data stream. TCP/IP is the
basis on which services such as WWW, Mail and News are built. There are other protocols as well. In order to access the Internet from a PC, TCP/IP must be set up on the
PC.
UDP
User Datagram Protocol. UDP is a Protocol of the TCP/IP protocol family that handles
data transport between two communication partners (applications). Unlike TCP, UDP
is a non-session based protocol. It does not establish a fixed connection. The recipient
62
Glossary
is responsible for making sure the data is received. The sender is not notified about
whether it is received or not.
Uplink
Data that your SE680 WiMAX modem forwards from your PC or local network to external sites (e.g. to the Internet).
URL
Universal Resource Locator. Globally unique address of a domain on the Internet, e.g.
http://www.sagemcom.com.
Virtual server
A virtual Server provides a service on the Internet that runs not on itself, but on another
network component. The SE680 WiMAX can be configured as a virtual server. It will
then direct incoming calls for a service via Port forwarding directly to the appropriate
Port of the network component in question.
WAN
Wide Area Network. A WAN is a network that is not restricted to one particular area,
such as the Internet. A WAN is run by one or more public providers to enable private
access. You access the Internet via a Provider.
WiMAX
Worldwide Interoperability for Microwave Access. WiMAX is a modern wireless network technology that enables fast Internet connection even in remote areas where no
other connection possibility (e. g. DSL) is available.
63
Index
Index
Connectors . . . . . . . . . . . . . . . . . . . . . 9
Address Translation . . . . . . . . . . . . .
Administration. . . . . . . . . . . . . . . . . .
system password . . . . . . . . . . . . . .
Advanced Settings
features. . . . . . . . . . . . . . . . . . . . .
Antenna
adjusting . . . . . . . . . . . . . . . . . . . .
aligning precisely . . . . . . . . . . . . . .
connecting . . . . . . . . . . . . . . . . . .
Appendix . . . . . . . . . . . . . . . . . . . . .
CE declaration. . . . . . . . . . . . . . . .
putting into service . . . . . . . . . . . .
specifications . . . . . . . . . . . . . . . .
troubleshooting . . . . . . . . . . . . . . .
56
31
31
23
21
22
12
40
47
46
46
40
dB . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
dBm . . . . . . . . . . . . . . . . . . . . . . . . . 56
Device status. . . . . . . . . . . . . . . . . . . 36
DHCP . . . . . . . . . . . . . . . . . . . . . . . . 56
DHCP server . . . . . . . . . . . . . . . . 29, 56
Disposal . . . . . . . . . . . . . . . . . . . . . . . 6
DNS . . . . . . . . . . . . . . . . . . . . . . . . . 57
DNS (Domain Name System) . . . . . . 26
DNS server . . . . . . . . . . . . . . . . . . . . 26
Domain name . . . . . . . . . . . . . . . . . . 57
DoS (Denial of Service) . . . . . . . . . . . 30
Downlink . . . . . . . . . . . . . . . . . . . . . . 57
DSL . . . . . . . . . . . . . . . . . . . . . . . . . 57
Base station ID . . . . . . . . . . . . . . . . .
Basic settings
setting up Internet access . . . . . . .
starting . . . . . . . . . . . . . . . . . . . . .
Basic Setup Wizard
starting . . . . . . . . . . . . . . . . . . . . .
Bridge . . . . . . . . . . . . . . . . . . . . . . .
Bridge mode
LAN configuration . . . . . . . . . . . . .
37
20
20
Establishing a radio connection . . . . . 21
Ethernet . . . . . . . . . . . . . . . . . . . . . . 57
Exposed host . . . . . . . . . . . . . . . . . . 28
20
56
30
Checking connection . . . . . . . . . . . .
Configuration . . . . . . . . . . . . . . . . . .
administration . . . . . . . . . . . . . . . .
aligning antenna precisely . . . . . . .
Home . . . . . . . . . . . . . . . . . . . . . .
menu structure . . . . . . . . . . . . . . .
opening online Help . . . . . . . . . . . .
resetting to factory setting . . . . . . .
setting the language . . . . . . . . . . .
status . . . . . . . . . . . . . . . . . . . . . .
Connecting . . . . . . . . . . . . . . . . . . . .
Connecting a PC or switch . . . . . . . .
Connection mode . . . . . . . . . . . . . . .
Connection wizard
establishing a radio connection . . .
64
43
15
31
22
19
18
18
32
18
34
12
12
25
21
Firewall . . . . . . . . . . . . . . . . . . . . 26, 57
Firmware . . . . . . . . . . . . . . . . . . . . . . 57
Firmware update . . . . . . . . . . . . . . . . 33
Flat rate . . . . . . . . . . . . . . . . . . . . . . 57
FTP. . . . . . . . . . . . . . . . . . . . . . . . . . 58
Full duplex . . . . . . . . . . . . . . . . . . . . 58
FXS . . . . . . . . . . . . . . . . . . . . . . . . . 58
Gateway . . . . . . . . . . . . . . . . . . . . . . 58
Hacker defence . . . . . . . . . . . . . . . . . 26
Half duplex . . . . . . . . . . . . . . . . . . . . 58
Home . . . . . . . . . . . . . . . . . . . . . . . . 19
HTTP . . . . . . . . . . . . . . . . . . . . . . . . 58
HTTP proxy . . . . . . . . . . . . . . . . . . . . 58
Firefox . . . . . . . . . . . . . . . . . . . . . . 44
Internet Explorer. . . . . . . . . . . . . . . 44
setting up . . . . . . . . . . . . . . . . . . . . 44
Index
Hub . . . . . . . . . . . . . . . . . . . . . . . . . 58
IEEE . . . . . . . . . . . . . . . . . . . . . . . . 58
IEEE 802.16 . . . . . . . . . . . . . . . . . . . 59
Installation . . . . . . . . . . . . . . . . . . . . 10
connecting . . . . . . . . . . . . . . . . . . 12
location . . . . . . . . . . . . . . . . . . . . . 11
outdoor modem . . . . . . . . . . . . . . . 12
PC . . . . . . . . . . . . . . . . . . . . . . . . 12
Switch . . . . . . . . . . . . . . . . . . . . . . 12
switching on . . . . . . . . . . . . . . . . . 14
system requirements . . . . . . . . . . . 11
Internet. . . . . . . . . . . . . . . . . . . . . . . 25
connection mode . . . . . . . . . . . . . . 25
menu . . . . . . . . . . . . . . . . . . . . . . 25
protocol . . . . . . . . . . . . . . . . . . . . . 25
Internet access
setting up . . . . . . . . . . . . . . . . . . . 20
Internet connection
changing configuration. . . . . . . . . . 25
closing manually . . . . . . . . . . . . . . 19
opening manually . . . . . . . . . . . . . 19
setting up . . . . . . . . . . . . . . . . . . . 25
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
IP address . . . . . . . . . . . . . . . . . 15, 59
assigning automatically . . . . . . . . . 29
assigning static . . . . . . . . . . . . 29, 30
dynamic . . . . . . . . . . . . . . . . . . . . 59
private . . . . . . . . . . . . . . . . . . . 29, 59
public . . . . . . . . . . . . . . . . . . . . . . 59
static . . . . . . . . . . . . . . . . . . . . . . . 59
IP address block for DHCP . . . . . . . . 29
IPTV. . . . . . . . . . . . . . . . . . . . . . . . . 59
ISP. . . . . . . . . . . . . . . . . . . . . . . . . . 60
Java
allowing. . . . . . . . . . . . . . . . . . . . .
Firefox . . . . . . . . . . . . . . . . . . . . .
Internet Explorer . . . . . . . . . . . . . .
JavaScript
allowing. . . . . . . . . . . . . . . . . . . . .
Firefox . . . . . . . . . . . . . . . . . . . . .
Internet Explorer . . . . . . . . . . . . . .
44
44
44
44
44
44
LAN . . . . . . . . . . . . . . . . . . . . . . . . . 60
configuration . . . . . . . . . . . . . . . . . 29
Lease time . . . . . . . . . . . . . . . . . . . . 29
LED . . . . . . . . . . . . . . . . . . . . . . . . . 60
LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . 9
startup . . . . . . . . . . . . . . . . . . . . . . 14
Local network
Bridge mode . . . . . . . . . . . . . . . . . 30
Location . . . . . . . . . . . . . . . . . . . . . . 11
Login . . . . . . . . . . . . . . . . . . . . . . . . . 60
MAC address . . . . . . . . . . . . . . . . . . 60
MAC table . . . . . . . . . . . . . . . . . . . . . 30
ageing time . . . . . . . . . . . . . . . . . . 30
Mbps . . . . . . . . . . . . . . . . . . . . . . . . . 60
Menu structure . . . . . . . . . . . . . . . . . 18
NAT . . . . . . . . . . . . . . . . . . . . . . 27, 56
port forwarding . . . . . . . . . . . . . . . . 27
Network . . . . . . . . . . . . . . . . . . . . . . 60
Network adapter . . . . . . . . . . . . . . . . 60
Network Address Translation . . . . . . . 27
Network protocol . . . . . . . . . . . . . . . . 61
Notes on user guide . . . . . . . . . . . . . . 6
Opening online Help . . . . . . . . . . . . . 18
Operating mode
Bridge . . . . . . . . . . . . . . . . . . . . . . 24
Router . . . . . . . . . . . . . . . . . . . . . . 24
Password
forgotten . . . . . . . . . . . . . . . . . . . . 42
ping command. . . . . . . . . . . . . . . . . . 43
Pop-up blocker
Firefox . . . . . . . . . . . . . . . . . . . . . . 45
Internet Explorer. . . . . . . . . . . . . . . 45
Pop-up window . . . . . . . . . . . . . . . . . 45
Firefox . . . . . . . . . . . . . . . . . . . . . . 45
Internet Explorer. . . . . . . . . . . . . . . 45
Port . . . . . . . . . . . . . . . . . . . . . . . . . . 61
65
Index
Port forwarding . . . . . . . . . . . . . . 27, 61
setting up . . . . . . . . . . . . . . . . . . . 27
Port number . . . . . . . . . . . . . . . . . . . 61
illustration . . . . . . . . . . . . . . . . . . . 27
PPPoE pass-through . . . . . . . . . . . . 26
Product features . . . . . . . . . . . . . . . . . 8
Protocol . . . . . . . . . . . . . . . . . . . . . . 61
Provider . . . . . . . . . . . . . . . . . . . . . . 61
Putting into service . . . . . . . . . . . . . . 39
System requirements . . . . . . . . . . . . . 11
TAE. . . . . . . . . . . . . . . . . . . . . . . . . . 62
TCP . . . . . . . . . . . . . . . . . . . . . . . . . 62
TCP/IP . . . . . . . . . . . . . . . . . . . . . . . 62
Trademarks . . . . . . . . . . . . . . . . . . . . . 5
Troubleshooting . . . . . . . . . . . . . . . . . 40
customer service . . . . . . . . . . . . . . 42
other faults . . . . . . . . . . . . . . . . . . . 42
Radio status . . . . . . . . . . . . . . . . . . .
Reboot . . . . . . . . . . . . . . . . . . . . . . .
Resetting . . . . . . . . . . . . . . . . . . . . .
RJ . . . . . . . . . . . . . . . . . . . . . . . . . .
Router . . . . . . . . . . . . . . . . . . . . . . .
RSSI . . . . . . . . . . . . . . . . . . . . . . . .
37
33
32
61
61
61
Safety precautions . . . . . . . . . . . . . . . 5
Scan . . . . . . . . . . . . . . . . . . . . . . . . 21
Scope of delivery . . . . . . . . . . . . . . . . 8
Security . . . . . . . . . . . . . . . . . . . . . . . 5
disposal . . . . . . . . . . . . . . . . . . . . . 6
notes on user guide . . . . . . . . . . . . . 6
safety precautions . . . . . . . . . . . . . . 5
Server . . . . . . . . . . . . . . . . . . . . . . . 61
virtual . . . . . . . . . . . . . . . . . . . . . . 63
Setting the language . . . . . . . . . . . . . 18
Setting up Internet access . . . . . . . . . 20
SMTP. . . . . . . . . . . . . . . . . . . . . . . . 62
Specifications . . . . . . . . . . . . . . . . . . 46
Start screen . . . . . . . . . . . . . . . . . . . 19
Status . . . . . . . . . . . . . . . . . . . . . . . . 34
device . . . . . . . . . . . . . . . . . . . . . . 36
Internet . . . . . . . . . . . . . . . . . . . . . 35
LAN . . . . . . . . . . . . . . . . . . . . . . . 36
local network . . . . . . . . . . . . . . . . . 36
radio status . . . . . . . . . . . . . . . . . . 37
Subnet . . . . . . . . . . . . . . . . . . . . . . . 62
Subnet mask . . . . . . . . . . . . . . . . . . 62
Switch . . . . . . . . . . . . . . . . . . . . . . . 62
Switching on the devices . . . . . . . . . . 14
System password . . . . . . . . . . . . . . . 31
forgotten . . . . . . . . . . . . . . . . . . . . 42
66
UDP . . . . . . . . . . . . . . . . . . . . . . . . . 62
Updating firmware . . . . . . . . . . . . . . . 33
Upgrading firmware . . . . . . . . . . . . . . 33
Uplink . . . . . . . . . . . . . . . . . . . . . . . . 63
URL . . . . . . . . . . . . . . . . . . . . . . . . . 63
User Datagram Protocol see UDP
User interface . . . . . . . . . . . . . . . . . . 16
Home . . . . . . . . . . . . . . . . . . . . . . . 19
menu structure . . . . . . . . . . . . . . . . 18
opening online Help . . . . . . . . . . . . 18
setting the language . . . . . . . . . . . . 18
Virtual server . . . . . . . . . . . . . . . . . . . 63
WAN . . . . . . . . . . . . . . . . . . . . . . . . . 63
Web browser
configuring . . . . . . . . . . . . . . . . . . . 44
HTTP proxy . . . . . . . . . . . . . . . . . . 44
Java. . . . . . . . . . . . . . . . . . . . . . . . 44
JavaScript . . . . . . . . . . . . . . . . . . . 44
launching user interface . . . . . . . . . 15
menu structure . . . . . . . . . . . . . . . . 18
pop-up window . . . . . . . . . . . . . . . . 45
user interface . . . . . . . . . . . . . . . . . 16
WiMAX . . . . . . . . . . . . . . . . . . . . . . . 63
WiMAX network
access data . . . . . . . . . . . . . . . . . . 20
establishing a connection . . . . . . . . 21
scan. . . . . . . . . . . . . . . . . . . . . . . . 21
Issued by Sagemcom Broadband SAS
Sagemcom Broadband SAS
250, route de l'Empereur - 92500 RUEIL MALMAISON
© Sagemcom Broadband SAS 2011
All rights reserved. Subject to availability.
Rights of modification reserved.
www.sagemcom.com
05.2011

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : © Sagemcom Broadband SAS
Create Date                     : 2011:05:13 14:51:08Z
Modify Date                     : 2011:05:13 15:24:39+02:00
Subject                         : Full User Guide English
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : SE680 WiMAX
Creator                         : © Sagemcom Broadband SAS
Description                     : Full User Guide English
Creator Tool                    : FrameMaker 7.1
Metadata Date                   : 2011:05:13 15:24:39+02:00
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Document ID                     : uuid:e191b192-c644-43ac-8f6e-41fe83f9309e
Instance ID                     : uuid:f0dfd923-2cf5-485c-a818-6e0224463dc1
Page Mode                       : UseOutlines
Page Count                      : 67

EXIF Metadata provided by EXIF.tools