SDC INST 350 Narrow Line Magnetic Lock Installation Instructions
User Manual: SDC 350 Narrow Line Magnetic Lock Installation Instructions Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 3
| Download | |
| Open PDF In Browser | View PDF |
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com • E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS 350 NARROW LINE EMLOCK Retrofits Discontinued Locknetics 350+ Provides Superior Architectural Appearance 12-1/2” 2-1/4” 10” 1-1/2” 3/4” 2" Interlocking Mounting Plate Quick Mount Interlocking Mounting Assembly Frame Mounting Screws Armature Outswing Electrical Instructions: Electrical Specifications: Use properly fused U. L. Listed Power Supply Dual Voltage Do not install a diode in parallel with any magnetic lock. A diode will cause a delay when releasing the door and residual magnetism to occur. Power Consumption 12 or 24VDC 560mA@12VDC 309mA@24VDC DS Door Status Sensor SPDT, 250mA@24VDC LS Lock Status Sensor SPDT, 1A@24VDC Resistive Access controls and/or release contacts must be located in series with the positive (+) power lead of the EmLock. Supplied Mounting Hardware Any low voltage condition will cause erratic operation of the optional board sensor. Although SDC recommends the use of a Regulated DC power supply. A significant voltage drop will occur when using a full wave bridge rectifier. Installation Location – Indoor Dry SIGNALING C US PATENT NO. 5,376.910 LISTED P:\INSTALLATION INST\Electromagnetic Locks\INST-350.vsd REV -.1 03-16 Page 1 Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com 1. Fold template as indicated on dotted line. For single doors locate template against the door and header on the lock jamb side of the frame. 2. Mark and drill holes as indicated by the template. STEPS 1 & 2 3. Mount armature to door. STEP 3 STEEL WASHER 2X 5/16-18 SOC HD SCREW WITH 3/16 (5MM) ALLEN HEX ARMATURE REINFORCEMENT TUBE 1-3/4“ HOLLOW METAL DOOR 5/8“ DRILL 1/2” DRILL SEXNUT RUBBER WASHER HOLLOW METAL DOOR From Sexnut side of door, drill exactly 1/2” hole thru one metal thickness only. From Armature side of door, drill 5/8” hole to insert reinforcement tube. Press in sexnut and reinforcement tube all the way and mount armature to door using hardware provided. 4. Install magnet onto the header with the magnetic stripes towards the door side of the stop. Assure that the magnet and armature line up properly, then tighten down ALL mounting screws. STEP 4 P:\INSTALLATION INST\Electromagnetic Locks\INST-350.vsd REV -.1 03-16 Page 2 5. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the door. Tap with a soft hammer to ensure proper alignment and engagement. CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing STEP 5 6. Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock. SWITCH or ACCESS CONTROL 1 + 2 - + Power Supply 3 4 NO C A/C MAINS 5 NC Lock Status Switch (Relay) POWER SUPPLY - + 12VDC or 24VDC LED Status Indicator: RED – Energized and Unsecure - GREEN – Energized and Secure 24VDC DOOR POSITION SENSOR * N/C – RED COM – BLK N/O - GRN *Door Position Sensor (Reed switch) NC COM RED (open with door closed) BLACK GREEN (closed with door closed) NO Voltage Jumper 12VDC 7. Test operation. When all is operating properly, tighten all screws. To maintain surface plating from corrosion: Do not touch the lock face with your hands. Clean lock face with Scotch-Brite pad by 3M (do not use sandpaper). Apply a thin film of rust inhibitor (LPS-3) on lock face. Repeat application on armature plate. P:\INSTALLATION INST\Electromagnetic Locks\INST-350.vsd REV -.1 03-16 Page 3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2016:03:22 08:22:42-07:00 Modify Date : 2016:03:22 08:22:42-07:00 Author : sdc-36 Subject : Page Count : 3 Page Layout : SinglePage Page Mode : UseNone XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:6b773a69-f29d-11e5-0000-43ffd60428d4 Producer : PDFCreator 2.2.1.0 Keywords : Creator Tool : PDFCreator 2.2.1.0 Document ID : uuid:6b773a69-f29d-11e5-0000-43ffd60428d4 Format : application/pdf Title : INST-350 Creator : sdc-36 Description :EXIF Metadata provided by EXIF.tools