SDI Technologies B20 Bluetooth Noise Isolating Metal Earbuds User Manual B20 QSG v10

SDI Technologies Inc. Bluetooth Noise Isolating Metal Earbuds B20 QSG v10

User Manual

Front Cover
Back CoverInside page Inside page
Model: Li-B20
Quick Start Guide
Li-B20 earbuds
Silicon Ear Cushions USB Charging Cable
What’s Included:
CHARGE BEFORE USE
BC
Questions? Visit www.ekids.com or call 1-800-288-2792 Toll Free
B20 - QSG
(English )
Size: 390 x 160 mm (unfold), 130 x 160 mm (folded)
Color: 1C + 1C
Material: white Art paper
Dec 6, 2017
B20 - QSG
(English)
GETTING STARTED BLUETOOTH
EAR CUSHIONS
Basic Controls
Charging your earbuds
Earbuds must be charged before use.
• Connect small plug of USB charging cable to USB port and
connect the other end to a powered USB port.
• Indicator will glow red while charging and turn glow blue once charged.
• Earbuds should provide about 4 hours of audio when fully charged.
NOTE: While charging, the earbud power will turn off to conserve battery power and minimize
charging time.
Multi-Function
(MF) Button
Plus Button
Minus Button
Press and hold 3 seconds
power earbuds ON
Press and hold 7 seconds
power ON and enter pairing
mode (blue and red LEDs flash)
Short press
play/pause/resume audio
Short press
answer/end calls
Press and hold 2 seconds
access Siri/Google Now
Press and hold 5 seconds
power earbuds OFF
Short press
next track
Press and hold
increase volume
Press and hold
for 5 seconds to
reset while in
pairing mode
Short press
restart track
Short press
previous track
Press and hold
lower volume
iHome iB39
3s
7s
Note: Noise isolation ear buds like the B20 are designed to provide a good seal in your ears and
block outside sounds. You should not use noise isolation ear buds in situations that require you to
hear outside warning sounds.
TIP: on some iOS (Apple) devices; you can view the B20 battery status on your device's screen.
when device is paired and connected; look for a vertical battery icon next to the Bluetooth icon on
the upper right corner of the device's screen.
Pairing establishes a unique communication connection between your Bluetooth device and the
earbuds. Once paired, you will be able to stream audio wirelessly to your B20 earbuds.
Bluetooth Noise Isolating Metal Earbuds
1.
The FIRST TIME EARBUDS ARE POWERED ON they enter auto-pairing
mode. The indicator on the dongle will flash blue and red and a voice
prompt will announce “power on”, then “pairing”.
The B20 comes with 3 sets of ear cushions to ensure a satisfying fit. If the
current ear cushions do not suit you, remove them and replace with
smaller or larger ear cushions.
2. Turn on Bluetooth mode on your device (under Settings, Connections
or similar)
3. Select “iHome B20” on your device’s menu of Bluetooth devices. When
pairing is successful, a voice prompt will announce “your device is
connected”. If prompted for a password, enter “0000” on your device.
You can now begin to stream audio and calls from your device.
4. For manual pairing or to pair other devices, press and hold the
Multi-Function Button for 7 seconds. The earbuds will power on,
attempt to autolink to a previously paired device, then enter pairing
mode. Pair your device per step 3 above.
Carrying Case
Limited One-Year Warranty Information
eKids, LLC warrants this product to be free from defects in workmanship and materials, under normal
use and conditions, for a period of one (1) year from the date of original purchase. Should this product
fail to function in a satisfactory manner, it is best to first return it to the store where it was originally
purchased. Should this fail to resolve the matter and service still be required by reason of any defect
or malfunction during the warranty period, eKids will repair or, at its discretion, replace this product
without charge. This decision is subject to verification of the defect or malfunction upon delivery of this
product to the Factory Service Center authorized by Customer Service. If service is required, please
call Customer Service at 1-800-288-2792 to obtain a Return Authorization Number and shipping
instructions. A copy of the sales receipt is required to validate in-warranty coverage.
Disclaimer of Warranty - NOTE: This warranty is valid only if the product is used for the purpose for
which it was designed. It does not cover (i) products which have been damaged by negligence or willful
actions, misuse or accident, or which have been modified or repaired by unauthorized persons; (ii)
cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players,
CD’s or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center
and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product
other than to the original purchaser. In no event will eKids or any of its
affiliates, contractors, resellers, their officers, directors,shareholders, members or agents be liable to
you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary
or punitive damages. (Some states do not allow limitations on implied warranties or exclusion of
consequential damages, so these restrictions may not apply to you.) This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by the above
mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency
(moneyorder, cashier's check, or credit card) for purchase of your eKids product.
Questions? Visit www.ekids.com
For any other questions: 1-800-288-2792 Toll Free
B20-110717-A (EN)
FCC ID: EMOB20
IC: 986B-B20
FCC/ Information
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
• Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B)/NMB-3(B)
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Microphone
Power/Charging
LED Indicators
Bluetooth is a registered trademark of Bluetooth SIG Inc. Bluetooth technology is incorporated
under license from Bluetooth SIG Inc.
Note: Voice prompts confirm the following functions: ‘Power On’, ‘Pairing’, ‘Your Device is
Connected’, ‘Maximum Volume’, and ‘Power Off’.
Declaración IC
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de
RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information
canadienne sur l'exposition et la conformité de rf.

Navigation menu