SDI Technologies ISB01 WiFi Motion Sensor User Manual iSB01 Motion Sensor QSG v17

Download:
Mirror Download [FCC.gov]
Document ID	3537490
Application ID	6Hqnhxl+8G2P+3be1QKSPg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.08kB (263480 bits)
Date Submitted	2017-08-31 00:00:00
Date Available	2017-08-31 00:00:00
Creation Date	2017-08-16 17:06:59
Producing Software	Adobe PDF library 15.00
Document Lastmod	2017-08-16 17:06:59
Document Title	iSB01 Motion Sensor_QSG_v17
Document Creator	Adobe Illustrator CC 2017 (Macintosh)

Model: iSB04 QSG (English)
Size: 153mm x 98mm
Date : August 16,2017
Pages:
Version:
Accordian style
Quick Start Guide
Model: iSB01
Intelligent Home Solutions
Quick Start Guide
NOTE: Tape should be adhered to a clean/dry surface. We strongly recommend
wiping with rubbing alcohol or soapy water to allow for the strongest bond.
BACK
Make sure the sensor is mounted vertically with the iHome logo upright).
For corner placement,
For flat wall placement,
apply tape to both sides
apply tape to spine
of sensor as shown
of sensor as shown
Flashing Green:
Solid Green:
Status LED
Flashing Red:
www.ihome.com
Optional Wall Mounting Instructions
Once satisfied with the sensor location, peel back the adhesive strip and press
sensor against the wall for 20 seconds to ensure a good bond.
Wi-Fi Status Indicators
Action Button
NOTE: If you intend to use a mix of devices (iOS AND Android), please set up
the Sensor using your iOS device and then share to your Android device(s).
NOTE: We recommend performing setup in the same location you intend to
place your sensor.
Motion Sensor Lens
Apple device running iOS 9.3 or later or Android device running KitKat 4.4
or later connected to your preferred WiFi network
Wi-Fi Setup
• iSB01 Motion Sensor
Battery Access Tab
WiFi network transmitting at 2.4GHz; WPA2 security type
What’s in the Box
Sensor Overview
WHAT YOU’LL NEED
1.800.288.2792
Your sensor comes with 3 AA batteries which must be installed before use.
• 3 AA batteries (see page 2 for battery installation instructions)
Monitor your home from anywhere with your smartphone
Questions?
Installing Batteries
• 3 Adhesive Mounting Strips (see page 4 for optional mounting instructions)
Wi-Fi MOTION SENSOR
FRONT
Overview: About Your Motion Sensor
Sensor is ready to
connect to a Wi-Fi
network
Gently pull the front of the sensor forward using the battery
access tab on top of the sensor to release the front of the
main unit.
Place the batteries in the battery compartment as shown.
Make sure polarity (+/–) matches the markings in the
product. Keep the ribbon under the batteries.
iHome Control provides 24-7 remote home monitoring from anywhere. The free iHome
Control app keeps you aware of changes in your home environment even when you’re
not home. For information about compatible products and to purchase Sensors and
SmartPlugs, visit iHome.com.
Height
up to 15 ft
Press and hold the Action Button on your sensor for 5 seconds until green LED is
flashing, then release.
100°
up
to
15
ft
up to 15 ft
4’
Flat wall
0’
Below are a few considerations when placing/mounting your motion sensor:
Enter the following setup code when prompted in the app.
• We recommend placing the sensor 4 - 7 feet (1.25 -2 meters) off the ground.
• We suggest to keep the sensor away from direct sunlight and other IR devices (such as
remote controls) as that may increase the chance for false detection.
Press the front and back cabinet together.
• The sensor includes an Occupancy Duration setting to determine how long your room
is considered occupied after detecting motion. To maximize battery life, the default
setting is 30 minutes. Use the app to change this setting to suit your needs.
NOTE: If you see a solid or flashing RED LED, press and hold the Action Button
for 5 seconds and then repeat steps 2 and 3
Notices
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To assure continued FCC compliance:
1.
IC
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm between the radiator and your body.
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Cet appareil radio est conforme au CNR-247d’Industrie Canada. L’utilisation de ce dispositif est autorisée seulement aux
deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter
tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du
dispositif.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre
corps.
GENERAL BATTERY PRECAUTIONS
• Never use or charge a battery if it appears to be leaking,
discolored, deformed, or in any way abnormal.
• Do not mix old and new batteries
• Use onlynew batteries of the type recommended
• Avoid charging a rechargeable battery when the temperature is not within
5°C - 35°C (41° - 95° Fahrenheit).
• Never expose a battery to any liquid.
• Never expose a battery to excessive heat such as direct sunlight or fire. Never use a battery
pack in an unventilated vehicle
where excessive internal temperatures may be encountered.
• Always keep batteries out of the reach of infants and small children.
• Remove batteries if device will not be used for a prolonged period to avoid corrosion which
can damage the unit
• Dispose of batteries that are leaking
Dispose of batteries in accordance with local regulations
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
TAPE CANNOT BE EASILY ADJUSTED
PLEASE BE THOUGHTFUL WHEN PLACING THE SENSOR
11’
7’
sensors icon and then the Add Device Button.
Press
Sensor coverage
• The sensor has a range of 15 feet (5 meters) directly in front of it and 15 feet
(5 meters) to either side (100° of coverage).
Sensor failed setup,
please try setup again.
Meet the iHome Control family of
Intelligent Home solutions
Sensor range
Corner
NOTE: When typing, dashes are not required
Sensor is connected
to a Wi-Fi network
(appears briefly
after setup)
Sensor Placement
Download and open the
iHome Control app from the App Store or Google Play.
Login to or create an iHome account
CAN ICES-(B)/NMB-3(B)
For warranty information:
visit https://www.ihomeaudio.com/support/

---

Source Exif Data:

EXIF Metadata provided by EXIF.tools