SEGI RED301-1WSS2 Keyless Entry System (Remote Controller) User Manual 20180504 v1 VA5RED301 1WSS2

Download:
Mirror Download [FCC.gov]
Document ID	3840302
Application ID	8vX/8xaAd4eqTE+kmsE8kQ==
Document Description	User Manual_20180504_v1 - VA5RED301-1WSS2_User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	49.4kB (617560 bits)
Date Submitted	2018-05-05 00:00:00
Date Available	2018-05-08 00:00:00
Creation Date	2018-05-04 17:43:04
Producing Software	Microsoft® Word 2016
Document Lastmod	2018-05-04 17:43:04
Document Title	User Manual_20180504_v1 - VA5RED301-1WSS2_User Manual
Document Creator	Microsoft® Word 2016
Document Author:	Yosep

2-WAY REMOTE & Antenna STARTING SYSTEM
WITH 1 BUTTONS
FOR AUTOMATIC TRANSMISSION
RED301-1WAY / MA1000-2WAY3
User Guide
Using the remote control
Description of Remote Appearance
Lock, Unlock and Remote
Lock, Unlock and Remote
Starting icon is displaying with
Starting icon is displaying with
One LED color.
Two LED color.
Lock/Unlock
Note: Press the button 1 time on the
remote control transmitter to lock the
vehicle. Press the button 2 times to
START/STOP:
unlock the driver’s door, 2 additional
Note : Remote Engine Start -
times to unlock all doors.
Press the button 1 time and then,
within 3 seconds, press and hold
the button for 2 seconds
2Way Remote
Remote Engine Stop - Press
the button for 2 seconds
Button Functions
Button
Press buttons for
LED
Function
Press 1time
Lock
Press 2 times
Unlock driver’s door
Press 2times x 2
Unlock all doors
2 seconds
Remote start/stop
Note: You make sure press button only after LED lighting ends to activate each feature properly.
1Way Remote
Vehicle Presets
Heater
When leaving the vehicle it is recommended to preset the accessory controls in preparation for the Next remote start. Settings for the blower motor(fan),front and rear (if
equipped),should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM instead.
Windshield Wipers, Headlights
Certain vehicles require the windshield wipers and headlights circuits to become energized while running under remote start. When leaving the vehicle you must ensure that
the windshield wipers and headlights switches are OFF. Leaving the headlights switch ON on certain types of vehicles could cause them to remain ON even after remote
starter shutdown, resulting in a dead battery.
Leave Windshield Wipers off to avoid damage wipers/motor with remote start.
Changing the Remote Control Transmitter Battery
Remote transmitter should be provided with two 3-volt lithium battery (Model: CR-2025).
Please pay attention that with low battery LED in the remote might not work and the remote start distance might get shorter.
Batteries can be purchased at any electronic device stores.
Following the instructions below to change the remote control battery
1. You may use a coin to pry the remote control halves apart
2. Remove the old battery and replace with a new one
3. Be sure to observe the (+) sign when inserting the new battery.
4. Before assembling transmitter case, you should test the remote control.
Note: LED icon of 2way transmitter indicates firstly blue color and then change to “RED” color when you press any button. In this case, it’s time to change CR2025 battery
newly
Description of Antenna Appearance
2Way Antenna
Antenna Harness
<< Installation of Antenna >>
Note: Use the power of the antenna car battery 12volts.
The Antennas have been calibrated for horizontal installation at the left-top corner of the windshield.
Remote-Starting your Vehicle
Remote-Starting
For the 2-way remote:
1. Press the
button one time. The remote will beep once and display the Lock icon. Then, press the
button within 2 seconds. The remote will beep once and
display the KEY icon.
2. 5 seconds later, the remote will activate starter. The Key icon will be shown with 3 different tones of beeping then the LED Icon will be scrolled..
For the 1-way remote:
1. Press
button one time and Lock LED will be displayed. Then press
button for 2 seconds within 3 seconds.
2. Remote Stop - Press button for 2 seconds.
If your vehicle does not start at the first attempt, the system will shut down, wait a few seconds and try to start the engine again. There will be 3 start attempts before the
system gives up.
Note: Please make sure press to button only after LED lighting ends to activate each feature properly.
Driving Off (Steps from Remote Start to Driving)
With the vehicle running remotely, press
button 2 times to disarm the OEM Starter Kill and/or the OEM alarm and unlock the doors. Enter the vehicle and do the
following:
1. Turn the ignition key to the IGNITION ON (RUN) position.
(Do not turn the key to the CRANK position while the engine is running. This would cause the starter motor to reengage. Disarm the remote starter mode by pressing the foot
brake)
2. Press the brake pedal to disengage the remote starter unit. With the vehicle key is in the IGNITION ON position, press the brake pedal or wait 30 seconds for the vehicle to
turn to ready status to drive.
Note: In remote engine start status, engine will be deactivated according to following conditions.
- Open the door and 30 seconds is passed.
- Press brake pedal without key is in IGNITION ON position.
Engine Run Time
Your Remote Car Starter can be programmed to run the engine for 10 or 5 minutes (10 minutes by default).
Note : Run time is set by installer.
To check the amount of runtime remaining (2-way only):
After pressing
button once, if you press
button 2 times within 3 seconds, remote starter will be operated. Once remote starter is succeeded and the
engine is turned on, the remote will receive signal and shows the remaining remote starter time as a START LED icon.
Remote Starter Features
Remote Start Error Diagnostic
If remote engine starter fails, the vehicle will not be started and the horn will sound accordingly to the table below.
Number of Horn times
Remote Start Error
Hood open
KEY IN or IG1 ON
Valet mode
Brake press
Trunk open
Door open
Valet/Service Mode
For REMOTE Start KEY Fob
Valet/Service mode is used to prevent the system from unexpectedly starting the engine while being serviced.
When your vehicle is in Valet Mode, the remote starter functionalities are disabled. If the vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the
engine from being remote-started accidentally.
Any of the following features will put your remote car starter into Valet Mode :
Remote Valet:

This feature allows you to put your system into Valet Mode by using the transmitter.
To Engage Valet Mode/Service Mode: (Approaching to Function stop mode)
1) Insert the vehicle’s key to the IGNITION, turn to the ON position.
2) Press and hold the vehicle brake.
3) Press and hold the remote
button for 2 seconds, the key LED will flash and the vehicle’s indicator will flash 1 time. Valet mode is engaged.
To take the system out of Valet Mode (Return the system to its normal operating mode): (Disarming “Function Stop Mode”)
1) Insert the vehicle’s key to the IGNITION, turn to the ON position.
2) Press and hold the vehicle brake.
3) Press and hold the remote
button for 2 seconds, the key LED will flash and the vehicle’s indicator will flash 2 times, Valet mode is cancelled.
To verify whether the system is in Valet Mode using the 2-way remote:
If system is in Valet mode, buzzer sounds shortly when lock or unlock button is pressed.
Advanced Features: Installation-programmable Options
The Remote Car Starter was designed with flexibility and OEM integration in mind. With its programmable options, this unit can virtually control nearly any electrical system in
your vehicle.
Caution: The programming of your system should be left to a professional.
Changing any one of the settings may affect the operation of your Remote Car Starter.
Engine Run Time setting
Option Setting Condition
Disarm the vehicle with remote control transmitter.(Unlock)
Driver s door must be physically Open, Engine Stop, Ignition ON, Trunk Open and Hood Open.
Option Setting Instruction
- Under option setting condition, press button for 2 seconds.
Light and Horn of vehicle will activate according to Engine Run Time option.
Number of Indicator+ Horn
Settings
1 Time
10 Mins (Default)
2 Times
5 Mins
Light Blinking during remote engine start
Option Setting Condition
Disarm the vehicle with remote control transmitter.(Unlock)
Driver s door must be physically Open, Engine Stop, Ignition ON, Trunk Open and Hood Open.
Option Setting Instruction
- Under option setting condition, press button for 2 seconds.
Light and Horn of vehicle will activate according to Light Blinking during remote engine start.
Number of Indicator+ Horn
Status
1 Time
Blink OFF (Default)
2 Times
Blick ON
Pairing Remote Start Fob
The Remote Start Fobs in Remote Start Kit are already paired with the main module at the time of production.
There is no need to pair the Fobs at the time of the first installation.
1. When a new registration is needed
- When replacing a remote due to loss or malfunction of a remote.
- When replacing the main controller installed in the vehicle.
- When adding or changing the remote upon user’s need.
2. Pairing procedure
RS Fob X1
5X
1) Open driver’s door and trunk.
2) Insert the key into the ignition. Turn the key from OFF to ON position 5 times within 5 seconds.
3) After step 2), within 5 seconds, Press button on the 1st Remote Start Fob 1 time.
4) After registering the 1st Remote Start Fob, within another 5 seconds, Press button on the next 2nd Remote Start Fob 1 time.
5) Verify that all Fobs are functioning correctly by performing Lock / Unlock function.
NOTE:
1) A system can recognize up to 3 remotes maximum.
2) If a new Fob, or additional Fob, is needed later, the Fob pairing process should be done with the original Fob or oldest available Fob.
Troubleshooting Poor Transmitting Range
Many factors may affect the operating range of the transmitter. Some of these are:
-The condition of the batteries in the transmitter.
-The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers, etc).
-Metal in the area of the vehicle of transmitter. This includes the vehicle itself.
-The shape of the vehicle can affect range as well. Vans in general have greater interference.
The shape of the roof and A-pillars causes considerable radio-frequency interference.
Demonstrate to users that the best range is facing the vehicle's front.
The worst range is facing the vehicles right or left side.
Please inform the users that facing the vehicle’s front offers the best range.
The worst range is experienced facing the R or L side.
-The amount of other vehicles in the area of the target vehicle.
-The method of using the transmitter. Always hold the transmitter high, approximately at shoulder height.
Automatic Engine Start Repeat
Remote Start is programmed to repeat the engine start sequence two (2) more times after ten (10) seconds if the engine start fails because of low vehicle battery.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 11
Language                        : ko-KR
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Creator                         : Yosep
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2018:05:04 17:43:04+09:00
Modify Date                     : 2018:05:04 17:43:04+09:00
Document ID                     : uuid:FD6D1504-44CC-42DC-AA25-0BD3D18DE011
Instance ID                     : uuid:FD6D1504-44CC-42DC-AA25-0BD3D18DE011
Author                          : Yosep

EXIF Metadata provided by EXIF.tools