SEIKAKU TECHNICAL GROUP MODAU-800R Wireless Microphone Receiver User Manual AU 800R 800P 800H ALTO FCC
SEIKAKU TECHNICAL GROUP LIMITED Wireless Microphone Receiver AU 800R 800P 800H ALTO FCC
Contents
- 1. User Manual I
- 2. User Manual II
User Manual I
![](/img.php?id=926719&img=bg1.png)
WIRELESS MICROPHONE SYSTEM
AU-800R
AU-800H/AU-800P/AU-800LV/AU-800HS/AU-800G
OWNER'S MANUAL
www.altoproaudio.com
Version 1.4 DEC. 2007
LTO
RR
c
All rights reserved to ALTO. All features and content might be changed
without prior notice. Any photocopy, translation, or reproduction of part of this
manual without written permission is forbidden. Copyright 2007 Seikaku Group
SEIKAKU TECHNICAL GROUP LIMITED
NO. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwan
http://www.altoproaudio.com Tel: 886-4-22313737
email: alto@altoproaudio.com Fax: 886-4-22346757
HM-38
LTO
R
NF02566-1.4
![](/img.php?id=926719&img=bg2.png)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
PLEASE DO NOT REMOVE THE COVER OR
THE BACK PANEL OF THIS EQUIPMENT.
THERE ARE NO PARTS NEEDED BY USER
INSIDE THE EQUIPMENT. FOR SERVICE,
PLEASE CONTACT QUALIFIED SERVICE
CENTERS.
WARNING
To reduce the risk of electric shock
and fire, do not expose this equipment
to moisture or rain.
Dispose of this product should
not be placed in municipal waste
and should be separate collection.
Move this Equipment only with a cart,
stand, tripod, or bracket,
specified by the
manufacturer, or
sold with the
Equipment. When
a cart is used, use
caution when
moving the cart /
equipment
combination to
avoid possible
injury from tip-over.
Permanent hearing loss may be caused by
exposure to \ extremely high noise levels.
The US. Government's Occupational Safety
and Health Administration (OSHA) has
specified the permissible exposure to noise
level.
These are shown in the following chart:
This symbol, wherever used, alerts you to th e
presence of un-insulated and dangerous voltages
within the product enclosure. These are voltages that
may be sufficient to constitute the risk of electric
shock or death.
This symbol, wherever used, alerts you to
important operating and maintenance instructions.
Please read.
Protective Ground Terminal
AC mains (Alternating Current)
Hazardous Live Terminal
ON: Denotes the product is turned o n.
OFF: Denotes the product is turned off.
The apparatus shall be connected to a mains
socket outlet with a protective earthing
connection.
The mains plug or an appliance coupler is used
as the disconnect device, the disconnect device
shall remain readily operable.
CAUTION
Describes precautions that should be observed to
prevent damage to the product.
Read this Manual carefully before operation.
Keep this Manual in a safe place.
Be aware of all warnings reported
with this symbol.
Keep this Equipment away from water and
moisture.
Clean it only with dry cloth. Do not use
solvent or other chemicals.
Do not damp or cover any cooling opening.
Install the equipment only in accordance with
the Manufacturer's instructions.
Power Cords are designed for your safety. Do
not remove Ground connections! If the plug
does not fit your AC outlet, seek advice from
a qualified electrician. Protect the power
cord and plug from any physical stress to
avoid risk of electric shock. Do not place
heavy objects on the power cord. This could
cause electric shock or fire.
Unplug this equipment when unused for long
periods of time or during a storm.
Refer all service to qualified service personnel
only. Do not perform any servicing other than
those instructions contained within the
User's Manual.
To prevent fire and damage to the product,
use only the recommended fuse type as
indicated in this manual. Do not short-circuit
the fuse holder. Before replacing the fuse,
make sure that the product is OFF and
disconnected from the AC outlet.
7. WARRANTY
To obtain Warranty Service, the buyer should first fill out and return the enclosed
Warranty Registration Card within 10 days of the Purchase Date.
All the information presented in this Warranty Registration Card gives the
manufacturer a better understanding of the sales status, so as to provide a
more effective and efficient after-sales warranty service. Please fill out all the
information carefully and genuinely, miswriting or absence of this card will void
your warranty service.
2.1 In case of return for any warranty service, please make sure that the
product is well packed in its original shipping carton, and it can protect your
unit from any other extra damage.
2.2 Please provide a copy of your sales receipt or other proof of purchase with
the returned machine, and give detail information about your return address
and contact telephone number.
2.3 A brief description of the defect will be appreciated.
2.4 Please prepay all the costs involved in the return shipping, handling and
insurance.
3.1 warrants that this product will be free from any defects in materialsLTO
and/or workmanship for a period of 1 year from the purchase date if you
have completed the Warranty Registration Card in time.
3.2 The warranty service is only available to the original consumer, who purchased
this product directly from the retail dealer, and it can not be transferred.
3.3 During the warranty service, may repair or replace this product at itsLTO
own option at no charge to you for parts or for labor in accordance with the
right side of this limited warranty.
3.4 This warranty does not apply to the damages to this product that occurred
as the following conditions:
Instead of operating in accordance with the user's manual thoroughly, any abuse
or misuse of this product.
Normal tear and wear.
The product has been altered or modified in any way.
Damage which may have been caused either directly or indirectly by another
product / force / etc.
Abnormal service or repairing by anyone other than the qualified personnel or
technician.
And in such cases, all the expenses will be charged to the buyer.
3.5 In no event shall be liable for any incidental or consequential damages. LTO
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion or limitation may not apply to
you.
3.6 This warranty gives you the specific rights, and these rights are compatible
with the state laws, you may also have other statutory rights that may vary
from state to state.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
![](/img.php?id=926719&img=bg3.png)
IN THIS MANUAL:
1. INTRODUCTION...............................................................................1
2. FEATURES......................................................................................3
3. CONTROL ELEMENTS.....................................................................4
4. OPERATION ...................................................................................8
5. ANNEX ..........................................................................................13
6. TECHNICAL SPECIFICATIONS..........................................................18
7. WARRANTY..................................................................................19
1. INTRODUCTION
Enjoy your AU-800 and make sure to read this Manual carefully before operation!
Thank you for your purchasing the AU-800 LTO wireless system.
Your AU-800 is based on a new revolutionary UHF PLL (phase loop locked) circuit
which allows the simultaneous use of more than 144 channels (depending on your
country regulations). The Receiver is provided with 2 antennas that constantly
monitor the incoming RF (radio frequency) signal and send only the stronger RF
signal to the AU-800R Receiver. Your AU-800 system is full of key features such
as AUTO-SCAN function, battery level monitoring and others.
AU-800H: It is a handheld transmitter with rubberised finished and level
hi-fi microphone capsule.
Depending on the options available your AU-800 system consists of:
ANT B
GROUP CHANNEL
AF
RF
MHz
AU-800R
ANT-A ANT-BPOWER
R
LTO
PLL UHF DIVERSITY WIRELESS RECEIVER
UP MENU
DOWN MEM
AU-800H
R
LTO
MHz
6. TECHNICAL SPECIFICATION
Model
Channel
Frequency band
Receiver type
Frequency response
Frequency stability
T.H.D.
Modulation mode
S/N Ratio
Dynamic
RF sensitivity
Audio output
Balance output
Power supply
Dimensions (WDH)
Weight
Multi-channels, up to 144 frequency presets for each frequency band
UHF 470-900 MHz (Dependent on applicable country regulations)
PLL UHF SYNTHESIZED
50 Hz-15 kHz ( 3 dB)
0.005% (-10 -50 )
1 kHz 0.8%
FM (F3E)
90 dB
100 dB
-100 dBm/30 dB SINAD
Unbalanced 6.3mm phone jack 550mV; 20KHz deviation
1.1 V, 20 kHz deviation
DC 15V/ 500mA (AC 115V/230V 50/60Hz adaptor)
210 155 44 mm; (8.2" 6.1" 1.7")
1.10 Kg
Model
Oscillation mode
Carrier Frequency Band
Frequency Response
Frequency Stability
T.H.D.
Modulation Mode
RF Output Power
Dynamic
Tone Trequency
Current Drain
Max. Deviation
Battery
Optional
Mic. Capsule(Optional)
Dimensions
Weight
PLL UHF SYNTHESIZED
UHF 470-900 MHz Dependent on applicable country regulations
50 Hz-15 kHz ( 3 dB)
0.005% (-10 ~ 50 )
FM (F3E)
5-50mW(adjustable 3 bands)
100 dB
30-33 kHz
100 mA
35 kHz
"AA" type 2
Nickel hydrogen battery+charger
Condenser or Dynamic Capsule
277 36.5mm (10.9" 1.44")
0.246 Kg
1 kHz<0.8%
Model
Oscillation mode
Carrier Frequency Band
Frequency Response
Frequency Stability
T.H.D.
Modulation Mode
RF Output Power
Dynamic
Tone Trequency
Current Drain
Max. Deviation
Battery
Optional
Mic. Capsule(Optional)
Dimensions
Weight
PLL UHF SYNTHESIZED
UHF 470-900 MHz Dependent on applicable country regulations
50 Hz-15 kHz ( 3 dB)
0.005% (-10 ~ 50 )
FM (F3E)
5-50mW(adjustable 3 bands)
100 dB
30-33 kHz
100 mA
35 kHz
"AA" type 2
Nickel hydrogen battery +charger
Condenser or Dynamic Capsule
1 kHz<0.8%
0.090 Kg
97 68 22 mm (3.82" 2.68" 0.87")
![](/img.php?id=926719&img=bg4.png)
Group 1-1: 850.125 Group 1-10: 851.925
Group 2-2: 852.725 Group 2-5: 859.925
Group 3-4: 857.725 Group 2-6: 862.325
Group 5-8: 867.725 Group 4-11: 874.725
Group 8-6: 863.525 Group 8-8: 868.325
: Dynamic Mic.
: 50 Hz~16 kHz( 3 dB)
: 300 20% at 1kHz
: -71 dB 3 dB
: Omni-directional
1. INTRODUCTION
AU-800P/800LV/800HS/800G
A bodypack transmitter with belt clip. The bodypack transmitter will
come with either:
(1). A cable to be connected to an electric guitar or bass (AU-800G).
(2). A Lavalier Microphone. This is the little "bug" to be clipped on ties, shirts,
nipples, etc.(AU-800LV)
(3). A Headset Microphone that is fit like a pair of sunglasses so that the Player
has both hands free to play an instrument, dance, shot the Audience, etc.(AU-800HS)
AU-800P
SELECT CH/ON
LTO
MHz
(1)
X:1000 Hz
Y:-50.9 dBv/Pa
Y:-48.6 dBm/Pa
D:0.0 dB
Y:-77.5 dBv/Pa
Y:-75.3 dBm/Pa
D:0.0 dB
D:-26.6 dB
-40
-90
-80
-70
-60
-50
20 50 100 200 500 1K 2K 5K 10K 20K
5. ANNEX
850.125 850.325 850.525 850.725 850.925 851.125 851.325 851.525 851.725 851.925 852.125 852.325
852.525 852.725 852.925 853.125 853.325 853.525 853.725 853.925 854.125 854.325 854.525 854.725
854.925 855.125 855.325 855.525 855.725 855.925 856.125 856.325 856.525 856.725 856.925 857.125
857.325 857.525 857.725 857.925 858.125 858.325 858.525 858.725 858.925 859.125 859.325 859.525
859.725 859.925 860.125 860.325 860.525 860.725 860.925 861.125 861.325 861.525 861.725 861.925
862.125 862.325 862.525 862.725 862.925 863.125 863.325 863.525 863.725 863.925 864.125 864.325
864.525 864.725 864.925 865.125 865.325 865.525 865.725 865.925 866.125 866.325 866.525 866.725
866.925 867.125 867.325 867.525 867.725 867.925 868.125 868.325 868.525 868.725 868.925 869.125
869.325 869.525 869.725 869.925 870.125 870.325 870.525 870.725 870.925 871.125 871.325 871.525
871.725 871.925 872.125 872.325 872.525 872.725 872.925 873.125 873.325 873.525 873.725 873.925
874.125 874.325 874.525 874.725 874.925 875.125 875.325 875.525 875.725 875.925 876.125 876.325
876.525 876.725 876.925 877.125 877.325 877.525 877.725 877.925 878.125 878.325 878.525 878.725
1. The values with underlines should be scanned manually by adjusting the UP/DOWN key.
2. The following channels can be used simultaneously without any interference.
918.325
918.525
919.925 920.125
920.325
920.525
920.725
920.925
922.325 922.525 922.725 922.925
923.125
923.325
924.725 924.925
925.125
925.325
925.525
925.725
927.125 927.325 927.525 927.725
927.925
928.125
929.525 929.725 929.925 930.125
930.325
930.525
931.925 932.125 932.325 932.525
932.725
932.925
934.325 934.525 934.725 934.925
935.125
935.325
936.725 936.925 937.125 937.325
937.525
937.725
939.125 939.325 939.525 939.725
939.925
940.125
941.525 941.725 941.925 942.125
942.325
942.525
915.125 915.325 915.525 915.725 915.925 916.125
917.525 917.725 917.925 918.125
918.725
918.925
921.125
923.525
923.725
925.925
926.125
928.325
928.525
930.725
930.925
933.125
933.325
935.525
935.725
937.925
938.125
940.325
940.525
942.725
942.925
916.325 916.525
921.325
919.125
919.325
919.525
921.525
921.725
921.925 922.125
923.925
924.125
924.325 924.525
926.325
926.525
926.725 926.925
928.725
928.925
929.125 929.325
931.125
931.325
931.525 931.725
933.525
933.725
933.925 934.125
935.925
936.125
936.325 936.525
938.325
938.525
938.725 938.925
940.725
940.925
941.125 941.325
943.125
943.325
943.525 943.725
916.725 916.925 917.125 917.325
919.725
![](/img.php?id=926719&img=bg5.png)
Group 1-1: 798.125 Group 1-10: 819.725
Group 2-2: 800.725 Group 2-5: 807.925
Group 3-4: 805.725 Group 2-6: 810.325
Group 5-8: 815.725 Group 4-11: 822.725
Group 8-6: 811.525 Group 8-8: 816.325
2. FEATURES
User Friendly interface including a large blue back lighted display and an
intuitive MENU system for easy operation.
Auto Scan Function
2 Antennas and switching diversity circuit
Selector for three different audio output levels depending of kind of mixer used
Squelch control to minimize RF interferences
Soft touch rubberised painting to avoid handling noise
Rechargeable battery design
Selector for three different output levels depending of kind of receiver used
LCD display
Battery status display
Mute function (this function is very welcomed by Politicians...)
Lock function to avoid miss action during a live performance
Each AU-800 System complies with E MC regulations and includes 144 different channels.
(Not all channels may be av ailable in certa in Countries depending on loc al regulations).
They are manufactured under ISO9000:2000, ISO/TS 16949:2002 quality
management system.
1. INTRODUCTION
680 ohm
50-12 kHz;
-65 dB 3 dB at 1kHz
12 180 mm( 0.47" 7.1")
22g(0.049Ib)
600 ohm
: 80-12 kHz;
-68 dB+/-3 dB at 1kHz;
Uni-directional;
52g (0.12Ib)
(2) (3)
798.125 798.325 798.525 798.725 798.925 799.125 799.325 799.525 799.725 799.925 800.125 800.325
800.525 800.725 800.925 801.125 801.325 801.525 801.725 801.925 802.125 802.325 802.525 802.725
802.925 803.125 803.325 803.525 803.725 803.925 804.125 804.325 804.525 804.725 804.925 805.125
805.325 805.525 805.725 805.925 806.125 806.325 806.525 806.725 806.925 807.125 807.325 807.525
807.725 807.925 808.125 808.325 808.525 808.725 808.925 809.125 809.325 809.525 809.725 809.925
810.125 810.325 810.525 810.725 810.925 811.125 811.325 811.525 811.725 811.925 812.125 812.325
812.525 812.725 812.925 813.125 813.325 813.525 813.725 813.925 814.125 814.325 814.525 814.725
814.925 815.125 815.325 815.525 815.725 815.925 816.125 816.325 816.525 816.725 816.925 817.125
817.325 817.525 817.725 817.925 818.125 818.325 818.525 818.725 818.925 819.125 819.325 819.525
819.725 819.925 820.125 820.325 820.525 820.725 820.925 821.125 821.325 821.525 821.725 821.925
822.125 822.325 822.525 822.725 822.925 823.125 823.325 823.525 823.725 823.925 824.125 824.325
824.525 824.725 824.925 825.125 825.325 825.525 825.725 825.925 826.125 826.325 826.525 826.725
1. The values with underlines should be scanned manually by adjusting the UP/DOWN key.
2. The following channels can be used simultaneously without any interference.
5. ANNEX
![](/img.php?id=926719&img=bg6.png)
Ok, enough with numbers. Let's start to fam iliarize with your AU-800 System.
First of all, the AU-800R Receiver:
It switches your AU-800R ON and OFF.
3. CONTROL ELEMENTS
SPOTLIGHT
Via this key you can activate the desired function.
You can enter the selected frequency via this key, moreover you can also
activate the AUTO-SCAN function via the same key.
You can adjust the right values through these two keys once the MENU is
activated.
All the key functions of your AU-800 Receiver are monitored through this
big, amazing, blue back lighted display such as: Ra dio Signal, Audio Signal,
Battery life (absolutely with some little magic you ca n see the battery life of
the transmitter directly on the receiver!), group va lue, channel value and the
selected frequency.
You must connected the two cute antennas you found in the box if yo u want
to get proper RF transmission.
ANT B
GROUP CHANNEL
AF
RF
MHz
AU-800R
ANT-A ANT-BPOWER
R
LTO
PLL UHF DIVERSITY WIRELESS RECEIVER
UP MENU
DOWN MEM
2 13
4
5
6 6
740.125 740.325 740.525 740.725 740.925 741.125 741.325 741.525 741.725 741.925 742.125 742.325
742.525 742.725 742.925 743.125 743.325 743.525 743.725 743.925 744.125 744.325 744.525 744.725
744.925 745.125 745.325 745.525 745.725 745.925 746.125 746.325 746.525 746.725 746.925 747.125
747.325 747.525 747.725 747.925 748.125 748.325 748.525 748.725 748.925 749.125 749.325 749.525
749.725 749.925 750.125 750.325 750.525 750.725 750.925 751.125 751.325 751.525 751.725 751.925
752.125 752.325 752.525 752.725 752.925 753.125 753.325 753.525 753.725 753.925 754.125 754.325
754.525 754.725 754.925 755.125 755.325 755.525 755.725 755.925 756.125 756.325 756.525 756.725
756.925 757.125 757.325 757.525 757.725 757.925 758.125 758.325 758.525 758.725 758.925 759.125
759.325 759.525 759.725 759.925 760.125 760.325 760.525 760.725 760.925 761.125 761.325 761.525
761.725 761.925 762.125 762.325 762.525 762.725 762.925 763.125 763.325 763.525 763.725 763.925
764.125 764.325 764.525 764.725 764.925 765.125 765.325 765.525 765.725 765.925 766.125 766.325
766.525 766.725 766.925 767.125 767.325 767.525 767.725 767.925 768.125 768.325 768.525 768.725
5. ANNEX
702.125 702.325 702.525 702.725 702.925 703.125 703.325 703.525 703.725 703.925 704.125 704.325
704.525 704.725 704.925 705.125 705.325 705.525 705.725 705.925 706.125 706.325 706.525 706.725
706.925 707.125 707.325 707.525 707.725 707.925 708.125 708.325 708.525 708.725 708.925 709.125
709.325 709.525 709.725 709.925 710.125 710.325 710.525 710.725 710.925 711.125 711.325 711.525
711.725 711.925 712.125 712.325 712.525 712.725 712.925 713.125 713.325 713.525 713.725 713.925
714.125 714.325 714.525 714.725 714.925 715.125 715.325 715.525 715.725 715.925 716.125 716.325
716.525 716.725 716.925 717.125 717.325 717.525 717.725 717.925 718.125 718.325 718.525 718.725
718.925 719.125 719.325 719.525 719.725 719.925 720.125 720.325 720.525 720.725 720.925 721.125
721.325 721.525 721.725 721.925 722.125 722.325 722.525 722.725 722.925 723.125 723.325 723.525
723.725 723.925 724.125 724.325 724.525 724.725 724.925 725.125 725.325 725.525 725.725 725.925
726.125 726.325 726.525 726.725 726.925 727.125 727.325 727.525 727.725 727.925 728.125 728.325
728.525 728.725 728.925 729.125 729.325 729.525 729.725 729.925 730.125 730.325 730.525 730.725
![](/img.php?id=926719&img=bg7.png)
2 3
AF OUT
BALANCED
AF OUT
UNBALANCED
15-18V DC
500mA
To connect a balanced cable with XL R connector (we forgot to tell you that
although your AU-800 system is wireless, you will still need to connect the
receiver to your Mixing Desk and to a wall plug !)
To be used with an unbalanced cable and standard 1/4" mono jack.
You can connect the supplied AC Adapter to this socket.
3. CONTROL ELEMENTS
SPOTLIGHT
This spring steel mesh grill will protect the microphone capsule during a live
performance. Especially made for heavy metal players, alcohol, drugs, etc.
This nice blue LCD will indicate the current operation status.
If you press this key for a few seconds, your Transmitter will be switched ON
or OFF. Once you have switched the unit ON, just press this key again slightly
and you can edit various parameters, such as CHANNEL, GROUP, RF POWER
LEVEL and LOCK/UNLOCK. Once you are in the LOCK position, no further
operation is allowed. And in a few seconds, the display will show the current
selected frequency (In MHZ). Battery level will also be shown.
1
1
3
2
456
7
AU-800H
R
LTO
MHz
572.125 572.325 572.525 572.725 572.925 573.125
573.325 573.525 573.725 573.925 574.125 574.325
574.525 574.725 574.925 575.125 575.325 575.525
575.725 575.925 576.125 576.325 576.525 576.725
576.925 577.125 577.325 577.525 577.725 577.925
578.125 578.325 578.525 578.725 578.925 579.125
579.325 579.525 579.725 579.925 580.125 580.325
580.525 580.725 580.925 581.125 581.325 581.525
581.725 581.925 582.125 582.325 582.525 582.725
582.925 583.125 583.325 583.525 583.725 583.925
584.125 584.325 584.525 584.725 584.925 585.125
585.325 585.525 585.725 585.925 586.125 586.325
638.125 638.325 638.525 638.725 638.925 639.125
639.325 639.525 639.725 639.925 640.125 640.325
640.525 640.725 640.925 641.125 641.325 641.525
641.725 641.925 642.125 642.325 642.525 642.725
642.925 643.125 643.325 643.525 643.725 643.925
644.125 644.325 644.525 644.725 644.925 645.125
645.325 645.525 645.725 645.925 646.125 646.325
646.525 646.725 646.925 647.125 647.325 647.525
647.725 647.925 648.125 648.325 648.525 648.725
648.925 649.125 649.325 649.525 649.725 649.925
650.125 650.325 650.525 650.725 650.925 651.125
651.325 651.525 651.725 651.925 652.125 652.325
5. ANNEX
![](/img.php?id=926719&img=bg8.png)
++
++
--
--
8
AU-800P
SELECT CH/ON
LTO
RR
MHz
The Antenna of your AU-800H is integrated in the microphone body.
Please do not cover the antenna for optimal RF transmission. We also
include 7 different color antenna covers for multiple operation of frequency.
Once you are in operation mode, you can access this key to edit certain
parameters. Press this key for a few seconds and the unit will enter in
the MUTE mode. (In this way, you can tell your Bass Player what you
think about the Sound Engineer without anybody knowing that!). Press
it again for a few seconds and you will unmute the unit.
This unit may be powered from one pair of dry or rechargeable batteries,
um3 size AA 1.5V.
With the rechargeable batteries putting inside, use the charger supplied to
recharge the batteries.
Note: This charger is for buyer's option. You can buy it from your dealer.
3. CONTROL ELEMENTS
SPOTLIGHT
1
2
3
45
6
7
5. ANNEX
Most countries closely regulate the radio frequencies used in the transmission
of wireless information. These regulations state which devices can use which
frequencies, and help to limit the amount of RF(radio frequency)interference in all
wireless communications. To be flexible enough to operate worldwide, MOD-800R
Wireless receivers are available in a number of models, each with a unique
frequency range. Each frequency range, or band, spans up to 24 MHz of the
wireless broadcast spectrum. Available bands are:
F1:470.000-494.000(470-496)MHz F2:518.000-542.000(518-544)MHz
F3:572.000-596.000(572-598)MHz F4:638.000-662.000(638-664)MHz
F5:702.000-726.000(702-731)MHz F6:740.000-764.000(740-769)MHz
F7:798.000-822.000(798-827)MHz F8:850.000-874.000(850-879)MHz
F9:915.000-939.000(915-944)MHz
470.125 470.325 470.525 470.725 470.925 471.125
471.325 471.525 471.725 471.925 472.125 472.325
472.525 472.725 472.925 473.125 473.325 473.525
473.725 473.925 474.125 474.325 474.525 474.725
474.925 475.125 475.325 475.525 475.725 475.925
476.125 476.325 476.525 476.725 476.925 477.125
477.325 477.525 477.725 477.925 478.125 478.325
478.525 478.725 478.925 479.125 479.325 479.525
479.725 479.925 480.125 480.325 480.525 480.725
480.925 481.125 481.325 481.525 481.725 481.925
482.125 482.325 482.525 482.725 482.925 483.125
483.325 483.525 483.725 483.925 484.125 484.325
518.125 518.325 518.525 518.725 518.925 519.125
519.325 519.525 519.725 519.925 520.125 520.325
520.525 520.725 520.925 521.125 521.325 521.525
521.725 521.925 522.125 522.325 522.525 522.725
522.925 523.125 523.325 523.525 523.725 523.925
524.125 524.325 524.525 524.725 524.925 525.125
525.325 525.525 525.725 525.925 526.125 526.325
526.525 526.725 526.925 527.125 527.325 527.525
527.725 527.925 528.125 528.325 528.525 528.725
528.925 529.125 529.325 529.525 529.725 529.925
530.125 530.325 530.525 530.725 530.925 531.125
531.325 531.525 531.725 531.925 532.125 532.325
![](/img.php?id=926719&img=bg9.png)
If you press this key for a few seconds, your Transmitter will be switched
ON or OFF. Once you have switched the unit ON, just press this key again
slightly and you can edit various parameters such as CHANNEL, GROUP,
RF POWER LEVEL and LOCK/UNLOCK. Once you are in the LOCK position
no further operation is allowed. And in a few seconds, the display will show
the current selected frequency (in MHZ). Battery level will also be shown.
Once you are in operation mode, you can access this key to edit certain
parameters. Press this key for a few seconds and the unit will enter in the
MUTE mode. (In this way, you can tell your Bass Player what you think about
the Sound Engineer without everybody knowing that!). Press it again for a few
seconds and you will unmute the unit.
This nice blue LCD will indicate the current operation status.
This connector is used to connect the unit with the clip microphones. for
example, HM-38 condenser microphone or LM-10 clip microphone.
With the rechargeable batteries put inside, use the charger supplied to
recharge the batteries.
This unit may be powered from one pair dry or rechargeable batteries,
Um3 size AA 1.5V.
,
, for Dynamic or Condenser microphone
, for Guitar, bass and keyboards
, GND
It is a flexible antenna. To get effective transmission, never cover the
antenna with hand, clothes, etc. during operation, and always position
the transmitter nearby the receiver.
It is the detachable belt clip for e asy carry during the live applications.
3. CONTROL ELEMENTS
SPOTLIGHT
Phantom power supply for Condenser microphone
You don't want accidental change of frequency or other setting in the middle of a
performance, do you? Any miss-operation during a live performance can be easily
avoided thanks to the LOCK function. With the LOCK function ON no further change
of setting is allowed until the Transmitter is unlocked. To access the LOCK Menu,
press the CH/ON key four times and then press the SELECT key to lock or unlock
the Transmitter Settings. Your choice of setting will automatically be saved into the
Transmitter in a few seconds. The blue display shows "lock" and "unlock" depending
on the operating mode.
Fig 10: LOCK
Fig 11: UNLOCK
Sometimes, there are things that you want to te ll to your Friends on stage or
your nearby Companion during a Meeting but not necessarily to the rest of the
world especially if you are ON LIVE on CNN... A smart feature on your Transmitter
allows you to easily MUTE the microphone so you are free to talk to the people
next to you without the rest of the world hearing what you say . To enter into
MUTE function simply press the SELECT key for a few seconds and the Transmitter
will mute any audio signal going to the Receiver. Press SELECT again for a few
seconds and you will UNMUTE the Transmitter.
3. CONTROL ELEMENTS
4. OPERATION
(1)
(4)
(3)
(2)
![](/img.php?id=926719&img=bga.png)
First of all, you should turn your Transmitter ON, then with your
AU-800R Receiver turned ON, press the MEM key at least for
one second. Your AU-800R will automatically look for the frequency
where your LTO Transmitter is operating. It will scan all the 12
Groups and Channels for a total of 144 frequencies available.
A.This indicates the Frequency Group. There are 12 Groups and each
Group includes 12 different channels (frequencies).
B.This indicates the Channel Number. There are 12 channels for each one
of the 12 Groups for a total of 144 channels.
C.MUTE: If the Display shows , the Mute function is disengaged. If the
display shows , the Mute function is engaged.
D.This shows the selected frequency.
E.This shows you the remaining life of the Battery of your Transmitter. 3
segments means full life, 1 segment means it is time to replace or
recharge the battery. If this icon disappeared, it means
that your transmitter is switched OFF.
F. This bar(AF) indicates the level of the audio signal coming into the Re ceiver.
G.This bar(RF) indicates the level of radio signal coming into the Receiver.
H.This indicates which of the 2 antennas is operating. Radio signal will
automatically switch from Ant 1 to Ant 2, indicating that the diversity
circuit is operating properly.
- And now, let's see the four keys in detail:
MEM key: The first function of this key is to activate the AUTO-SCAN
function. Suppose that you have more than one LTO transmitter in
front of you with your AU-800R Receiver and you want to start to
operate one of them with your AU-800 Receiver.
OK, if so far you remember all the functions and features of your AU-800
system you are ready to operate the Unit. Let's start from the Receiver:
3. CONTROL ELEMENTS
4. OPERATION
Note: Why LTO wireless systems come with 144 different frequencies?
Not because you will need to use 144 different microphones at the same
time. It is unlikely that you will use more than 8 systems at the same
time so why 144 frequencies? This mainly depends on Countries regulations.
We offer frequencies from 470 to 900 MHZ. Some of these frequencies
are illegal in certain Countries and vice versa. Offering such a wide range of
frequencies we make sure that each single Country on the planet will
have more than enough choice of frequencies available. Not only: A
certain frequency is close to the frequency generated by lighting equipment,
a computer, a fax machine and so on. Therefore, thanks to the large
number of frequencies available you can easily switch to another frequency
that is interference-free.
In your Transmitter, there are 12 frequency bands or GROUPS. Each Group
contains 12 channels according to EMC regulations.
To select a Group you must first switch your Transmitter ON by pressing the
CH/ON key for a few seconds until you hear the beep and the blue display is
lighted. Then press the CH/ON key again slightly and you will access the GROUP
menu. At this point use the SELECT key to change the GROUP value from 1 to
12. Now, to access the CHANNEL menu, press again slightly the CH/ON key
two times and use the SELECT key to change frequency from 1 to 12. Your
setting will be automatically saved in a few seconds and the display will go back
to the main menu showing the operating frequency.
Once you have changed the operating frequency on your Transmitter,
you need to activate the SCAN function in your AU-800R Receiver. In this way,
the Receiver with synchronize automatically on the Transmitter frequency.
Your Transmitter can operate on three different levels of output power . These
are different from the Handheld Model and the Bodypack model.
For the Handheld model the levels are
- PL 0, the output power is 0 dBm
- PL 1, the output power is 5 dBm
- PL 2, the output power is 10 dBm
And for the Bodypack version the levels are
- PL 0, the output power is 0 dBm
- PL 1, the output power is 5 dBm
- PL 2, the output power is 10 dBm
position the transmitter nearby the receiver.
3. CONTROL ELEMENTS
4. OPERATION
![](/img.php?id=926719&img=bgb.png)
Fig 3 mute function on
Fig 2 mute function off
This key activates several functions:
Press this key slightly once and you will get into the MANUAL SELECT for
the 144 frequencies. When the GROUP indicator is flashing, you can press
the UP/DOWN keys to select manually the desired Group. Then you can press
the MEM key to store this setting.
Press the MENU key twice and the CHANNEL indicator will flash. Use the UP/DOWN
keys to selected the desired channel and then press MEM key to store this setting.
Press the MENU key three times and you can adjust the OUTPUT LEVEL. Using
the UP/DOWN keys you have the choice to select three different levels:
PL 0 indicates that the output level is 1.1V
PL 1 indicates that the output level is 575mV
PL 2 indicates that the output level is 250mV
: This function is only available when using the XLR balanced output.
Press the MENU key four times and you will get into the MUTE function. Use the
UP/DOWN keys to mute/unmute the Unit.
Press the MENU key five times and you will activate the SQUELCH function. To
squelch or not to squelch, this is the issue...
Squelch is a complicated name to express a simple conce pt: The threshold above
or below that a signal is made pass through the receiver or not.
Fig 1
During this process, the audio output will be muted and the display will show
you the Group Number scanned, the channel number scanned and the
frequency that is being scanned. Once the transmitter frequency has been
found, the display will flash and the RF bar indicator and Battery life icon will
appear. Press MEM again slightly and such frequency will be stored into your
AU-800R Receiver. Please note that frequencies can be scanned manually
using the UP/DOWN key. See the Annex for more details.
AF
RF
MHz
AF
RF
MHz
AF
RF
MHz
3. CONTROL ELEMENTS
4. OPERATION
Fig 4
Press the CH/ON key for a few seconds and the transmitter will be powered ON.
At this point the blue back lighted display will show:
Fig 5
Preset frequency Remaining battery life
With the Transmitter switching ON, you can slightly press the CH/ON key again
and you will access to the following parameters:
Preset Group Preset Channel
The frequency at which the unit is operating
The Battery Status
And now that you know how to operate your AU-800R Receiver, let's
learn how to use the AU-800 Transmitters. The following instructions
apply both to the handheld version and to the bodypack version.
There are 2 keys on the Transmitter labelled CH/ON and SELECT.
Fig 6 Fig 7
MHz
AF
RF
MHz
3. CONTROL ELEMENTS
4. OPERATION
1
2
3
4
5
6
7
8
9
10
-100 dB
-96 dB
-93 dB
-90 dB
-87 dB
-85 dB
-83 dB
-81 dB
-79 dB
-77 dB