SES imagotag AP0002 digital network controller transceiver User Manual My

SES-imagotag GmbH digital network controller transceiver My

Contents

Product range description

ProductSpecificationAP-2010Last change: 27.03.2017
Product Specification AP-2010Page 2 of 271 Introduction 41.1 Key Features 41.2 Destination countries 41.3 Scope of delivery 42 Barcode Information 52.1 Serial Number 53 Mechanical Characteristics 73.1 Mechanical Dimensions 73.2 Front, Side and Top View 73.3 Upper Surface 83.4 Side View 83.5 Rear View 94 Mounting 104.1 Audience 104.2 General Instructions 104.3 Instructions for the Mounting Location 104.4 Approachability 114.5 Screw of the Antenna 114.6 Metal Bracket for Mounting on Wall, Ceiling or T-Mounting Rail 124.7 Mounting on Wall or Ceiling 125 Electrical Specifications 155.1 Used Channels 155.2 Difference WiFi and ESL protocol 155.3 Cabel Specifications 155.4 Power Supply Specifications 165.5 Pinout RJ45 Ethernet 166 Electrical & RF Characteristics 176.1 General Technical characteristics 176.2 Power and Current Consumption 176.3 General Specifications 177 Environmental 197.1 Humidity and Operating Conditions 19
Product Specification AP-2010Page 3 of 277.2 Storage Conditions 197.3 Cleaning Instructions 198 Packing 208.1 Packing Dimensions 208.2 Illustrations 208.3 Palletization 219 Certifications 229.1 Types 229.2 Overview 229.3 Applied Standards 229.4 Declaration 2210 Problems which requiring maintenance or replacement of the AP-2010 2411 Intended Use 2512 Improper Use 2613 Warranty 27
Product Specification AP-2010Page 4 of 271 IntroductionThe Access Point AP-2010 by imagotag is a network device similar to WLAN access points thatis required for communication with the imagotag electronic shelf labels (transmits priceinformation to the labels).Up to 10 000 labels can be managed per access point and the self-organizing network allowsautomatic roaming of labels without manual handling. The high transmission rate of the 2.4GHz wireless technology and the intelligent task scheduling enables fast and secure updateson imago G1 labels of all sizes.This document is the technical specification of the Access Point AP-2010.In the USA and Canada the AP-2010 usa/canada bundle incl. antenna with limited dataefficiency is required according to the FCC/IC regulations. This bundle has a reduced dataefficiency for label/updates/hour, for more details see label product specification.1.1 Key FeatureslManages up to 10 000 imago G1 labels of all sizeslCovers up to 1 950 m² (depending on shop layout)lLow power consumption – powered by PoE (Power over Ethernet) or with low power pluglEasy configuration and monitoringlOptimized scheduling of tasks and self-managed roaming of labels1.2 Destination countriesThe imagotag AP-2010 is currently intended for use in Europe, Canada and USA. More countrieswill follow.1.3 Scope of deliveryl1 pcs imagotag AP-2010l1 pcs 2.4-2.5GHz 5dBi antennal1 pcs metal mountingl1 pcs “caddy® clips 4G16M11“ from Erico®l2 pcs self-locking nuts M6May vary depending on configuration
Product Specification AP-2010Page 5 of 272 Barcode InformationThe AP-2010 comes with an AP-ID, P/N, MAC and S/N. The AP-ID consists of 5 decimal digits(0-9).Product Code: A1A001xxx2.1 Serial NumberDepends on Producer (A)2.1.1 Producer is 01Part Description Format Example Comment SourceA Producer 2alpha 01Specified byimagotag once foreach fabBProductfamily3alpha G1BSpecified byimagotag in theproduct specificationdocumentCProductversion3alpha 301DProductrevision3alpha 001Incremented on everychange of productspecification- Separator “-“ - FixedE Internal 1alpha B InternalCalculated duringproductionF Year 1 dec 4 4=2014, 5=2015,...G Week 2 dec 10 Calendar week in currentyear (01-53)H Weekday 1 dec 3I Internal 5 dec 00060 Continuous SerialNumber (Counter)
Product Specification AP-2010Page 6 of 272.1.2 Producer is not 01Part Description Format Example Comment SourceA Producer 2alpha 02Specified byimagotag once foreach fabBProductfamily3alpha R22Specified byimagotag in theproduct specificationdocumentCProductversion3alpha N01 N = with NFCDProductrevision3alpha 001Incremented on everychange of productspecification- Separator “-“ - FixedE Year 1alpha EE=2014, A=2010,B=2011,.. Calculated duringproductionF Week 2 dec 13G Internal 6 dec 000065 Continuous SerialNumber (Counter)Format: AABBBCCCDDD-EFFGGGGGGExample: 02G1B302001-E13000065Note:lCalendar week date is calculated according to ISO 8601 (see http://en.wiki-pedia.org/wiki/ISO_week_date
Product Specification AP-2010Page 7 of 273 Mechanical Characteristics3.1 Mechanical DimensionslWith antenna:oOutline (mm): 226 x 135 x 45oWeight: 350 glWithout antenna:oOutline (mm): 196 x 135 x 45oWeight: 320 g3.2 Front, Side and Top ViewFIGURE 1-1: Front, side and top view of the AP-20101Mounting plate fixation screw-hole3Antenna socket2LED 4Antenna
Product Specification AP-2010Page 8 of 273.3 Upper SurfaceFIGURE 1-2: Top view of the imagotag AP-20105Connection for the Power Supply 8Restart6LAN/PoE 9Reset to Factory Settings7Console3.4 Side ViewFIGURE 1-3: Side view of the imagotag AP-201010 Antenna Connector (unused) 12 Snap Connector Housing11 Warranty Seal
Product Specification AP-2010Page 9 of 273.5 Rear ViewFIGURE 1-4: Rear view of the imagotag AP-201013 Mounting Tab 17 Snap Connector Housing14 Mounting Rail 18 Housing Screw15 Locking Tab 19 Mounting Profile16 Label
Product Specification AP-2010Page 10 of 274 Mounting4.1 AudienceThe installation instructions are intended for trained electricians who can exhibit the followingqualifications:lKnowledge of the use of tools and work instructions.lKnowledge of the usable condition of the tool.lKnowledge of the electrical safety instructions.lKnowledge of the electrical building regulations.lKnowledge of the relevant standards.lKnowledge of assembly schedule.4.2 General InstructionslRead these installation instruction carefully before you connect the access point to thepower source.lThe company imagotag GmbH assumes no liability for injury to persons or damage to theAccess Point or damage to the environment caused by improper installation or mis-application.lRemove jewellery such as rings, necklaces, and watches before working on the device.lMake sure that the access point is not connected to the power source during assembly.lDon’t work on the access point during a thunderstorm and don’t connect a cable at thistime.lUse appropriate and tested climbing aid if you work above body height.Complete the installation and use the ERICO products just according theERICO® instruction. If necessary, you will find the desired data sheets atwww.erico.com and at every ERICO customer service.4.3 Instructions for the Mounting LocationThe Access Point could be mounted on a:lConcrete walllMortar walllT-Mounting RailSelect the installation location for the access point carefully. Pay particular attention to thefollowing requirements:lInstall the access point only in areas where the permissible environmental conditions(see ) can be observed.lDon’t install the access point in environmental with direct sunlight or heat source.lMount the metal bracket for the access point on dry surfaces only.
Product Specification AP-2010Page 11 of 27lDon’t mount the access point on any flammable material.lThe minimum bearing capacity of the substrate should be 5 kg.lThe LAN cable manufacturer must be complied with the default specifications (e.g. min-imum bend radius)4.4 ApproachabilitylMount the metal bracket that the access point can easily be pushed into the metalbracketlMake sure that the LAN socket is easily accessible after installation.lAfter installation the LED should be clearly visible.lIt is important that the inner surface of the access point have sufficient air circulation.The vents must be free to ensure good ventilation and prevent overheating.The mounting material (e.g. screws or pegs) for securing the metal bracket onconcrete wall is not part of the scope of delivery. It must be selected by theinstaller depending on the substrate itself.4.5 Screw of the AntennaFIGURE 1-5: Figure 3 - Screw of the Antenna1Front Part 3Direction of Rotation2Connection Socket 4Rear Part (Swivelling)Note: Screw the antenna with only the front part (1)
Product Specification AP-2010Page 12 of 274.6 Metal Bracket for Mounting on Wall, Ceiling or T-Mounting RailOnce the metal bracket is mounted, the AP-2010 will be mechanical connected and fixed with afixing screw.FIGURE 1-6: Figure 4 - Metal Bracket for imagotag AP-20104.7 Mounting on Wall or CeilingFIGURE 1-7: Figure 5 - Wall or Ceiling Mounting (Scheme)0Mounting Surface 3imagotag AP-20101Metal Bracket 4Fixation Screw2Mounting Screwa. Install the metal bracket to the wall or ceiling with the help of dowels and mountingscrews.
Product Specification AP-2010Page 13 of 27FIGURE 1-8: Figure 6 - imagotag AP-2010 Locking Tabsb. Slide the access point to the mechanical lock of the locking tabsc. Attach the AP-2010 with the enclosed fixation screw to the metal bracket4.7.1 Mounting on a T-Mounting RailAttach the metal bracket using the included “caddy® clips” from Erico® and the enclosed, self-locking screw nuts M6.FIGURE 1-9: Figure 7 - Mounting an AP-2010 on a T-Mounting Rail0T-Mounting Rail 3imagotag AP-20101Metal Bracket 4Fixation Screw2Self-locking Screw Nuts M6 5ERICO® „caddy® clips“a. Place 2 pieces of “caddy® clips” with the right distance on the T-Mounting Rail and fix it(twist)
Product Specification AP-2010Page 14 of 27b. Place the metal bracketc. Fix the Metal Bracket with 2 pieces of the self-locking screw nuts M6d. Slide the access point to the mechanical lock of the locking tabse. Attach the AP-2010 with the enclosed fixation screw to the metal bracket
Product Specification AP-2010Page 15 of 275 Electrical Specifications5.1 Used ChannelsAlthough WIFI and ESL use the same frequency band (2.4 Ghz ISM Band), there are channelsthat do not overlap (not interfering - recommended channels).Kanal Frequenz WLAN Kanal (802.11b/g)0 2404 MHzWLAN 1 (2402 – 2422 MHz)1 2010 MHz2 2422 MHz3 2425 MHz not interfering4 2442 MHz WLAN 6 (2427 – 2447 MHz)5 2445 MHz not interfering6 2462 MHz WLAN 11 (2452 – 2472 MHz)7 2470 MHz8 2474 MHz not interfering9 2477 MHz not interfering10 2480 MHz not interferingFIGURE 1-10: Overview of used channels of the imagotag AP-20105.2 Difference WiFi and ESL protocolIn contrast to the proprietary developed time based imagotag ESL protocol the WiFi protocolapplies to the IEEE 802.11 standard.FIGURE 1-11: WiFi and ESL frequencies and channels (22 Mhz bandwidth)5.3 Cabel SpecificationsYou can use a commercially available LAN cable (CAT-5 or higher) for data connection and thepower supply (if PoE is used) of the imagotag AP-2010.
Product Specification AP-2010Page 16 of 275.4 Power Supply SpecificationsSunny Computer Technology Europe s.r.o.lModel: SYS1541-1505-WxxlInput: 100-240 V ~ 1.0 A MAX, 50-60HzlOutput: 5V 3AlOutput Power: 15W MAXlOperating Temperature: 0° C to + 40° ClMTBF: 50.000 hours full rated load operation at 40 ℃, according to the MIL-HDBK-217F5.5 Pinout RJ45 EthernetlPin 3 – TX (AP to PC)lPin 6 – RX (PC to AP)lPin 4/5 – Ground5.5.1 Pinout
Product Specification AP-2010Page 17 of 276 Electrical & RF Characteristics6.1 General Technical characteristicsPower:lExternal Power Supply: 5 VDC / 3AlPower Supply via PoE: IEEE 802.3af, IEEE 802.3atlPower consumption: 15W MAX, typical 3WTechnology:lRadio technology: proprietarylOperating frequency: 2.4 GHz (ISM-Band) – 2.4835 GHzlTransmitted power: ≤ 10 dBmlNumber of Channels: 11lAccess protocol: proprietaryOther:lMTBF: >300.000h at 40°C according to SN295006.2 Power and Current ConsumptionPower consumption measurements indicate that the AP-2010 has the following patterns:lOperating Current: ≤ 60 mA (max. current)lOperating Power: ≤ 280 mWlSupply Voltage: 5V ± 10%6.3 General Specifications6.3.1 Hardwarel600 MHz ARM Cortex-A8lMemory - 512MB DDR2 memorylSD/MMC card connectoro512 MB card with imagotag software preinstalledlPower over Ethernet (PoE IEEE 802.3af / IEEE 802.3at)oThe original IEEE 802.3af-2003 PoE standard provides up to 15.4 W of DC power(minimum 44 V DC and 350 mA to each device). Only 12.95 W is assured to be avail-able at the powered device as some power is dissipated in the cable.lOther InterfacesoSerial RS232 Interfaceo10/100 Ethernet InterfacelPoweroPower source options (DC, PoE)o3.3 V I/O operationoDC supply 5V ± 10%, 3A Max
Product Specification AP-2010Page 18 of 276.3.2 Software PackagelOS: Embedded LinuxlAP-2010 application softwarelRF Firmware
Product Specification AP-2010Page 19 of 277 Environmental7.1 Humidity and Operating ConditionslTemperature: 0° C to + 40° ClHumidity: 10% to 80% (non-condensing)7.2 Storage ConditionslTemperature: -20 °C to + 70 °ClHumidity: 10% to 85% (non-condensing)7.3 Cleaning InstructionsSteps:1. Shutdown Access Point2. Plug Out Power Supply (AC or PoE)3. Clean the Access Point with the help of a damp clothNote: Do not use liquid or aerosol cleaners.
Product Specification AP-2010Page 20 of 278 Packing8.1 Packing DimensionsDIMENSIONS STACKING QUANTITYLENGTH WIDTH HEIGHTBOX 520 350 260 LAYER / UNIT 3 SETS / BOX 10PALLET 1200 800 140 BOXES / LAYER 4 SETS / LAYER 40UNIT 1200 800 960 BOXES / UNIT 12 SETS / UNIT 120Imagotag AP-2010 / Box: 108.2 Illustrations
Product Specification AP-2010Page 21 of 278.3 Palletization
Product Specification AP-2010Page 22 of 279 Certifications9.1 TypesHousing, board and the display are conform with the ROHS DirectiveThe product meets the EU safety, health and environmental protectionrequirements and has the approval of CE markingThis device complies with part 15 of the FCC Rules.9.2 OverviewCaption RoHS FoodContact CE FCC/ICAP-2010 • •2•51FCC/IC certified since calendar week 9 / year 2015 (the FCClogo must be printed on the nameplate)2R&TTE EN 300328 V1.8.13R&TTE EN 300328 V1.9.15There are two different versions of the AP available. One CE and one FCC version.9.3 Applied StandardsInformation Technology EquipmentEN 60950-1/A2:2013UL 60950-1/A2:2014CSA CAN/CSA-C22.2 NO.60950-1-07EMVEN 301489-17 V2.2.1R&TTEEN 300328 V1.8.1 / EN 300328 V1.9.1Human Exposure to Electromagnetic FieldsEN 62479:2010Radio internationalFCC:47 CFR Part 15 (USA)RSS-210 Issue 8 (Canada)9.4 DeclarationThe company imagotag GmbH declares on his own responsibility that the AP-2010 correspondsto the standards mentioned above.9.4.1 FCCThis device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept
Product Specification AP-2010Page 23 of 27any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance couldvoid the authority to operate the equipment.9.4.2 ICThis device complies with Industry Canada licence-exempt RSS standard(s). Operation issubject to the following two conditions: (1) this device may not cause interference, and (2) thisdevice must accept any interference, including interference that may cause undesiredoperation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareilne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectriquesubi, même si le brouillage est susceptible d'en compromettre le fonctionnement.9.4.3 NCC 警語:經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Product Specification AP-2010Page 24 of 2710 Problems which requiring maintenance or replacement ofthe AP-2010Plug out the power supply and contact the imagotag GmbH when it comes to the followingcases:lThe AP-2010 was strewn with liquid.lThe AP-2010 has been dropped or damaged.lThe LAN port of the AP-2010 is damaged.lThe antenna connection thread is damaged.lThe LED of the AP-2010 no longer lights up.Contact the manufacturer if despite intended purpose the device is not working and none of thementioned cases occurred.
Product Specification AP-2010Page 25 of 2711 Intended UseThe imagotag AP 2010 is exclusively designed to connect to electronic labels of the companyimagotag GmbH via radio.The device may only be used in areas where the environmental conditions be the same asdescripted in the chapter (see Environmental on page 19).Intended use includes the observance of all information in this system manual.
Product Specification AP-2010Page 26 of 2712 Improper UseAny use that is not mentioned in Section Intended Use, shall be deemed to be improper. Anydamage which result from improper use, the operator will assumes liability.The following usage is not allowed:lNever dismantle the electronic device because except battery there is no com-ponent which could be changed by someone who is not qualified.lDon't drop it.lKeep it away from water.lStrictly avoid direct contact with groceries.lDon’t use the electronic device with defective parts.lDon’t use the electronic device with spare parts and accessories which arenot examined and approved by the imagotag GmbH.lUnauthorized changes or modifications to the electronic device and their com-ponents without the consent of imagotag GmbH are not allowed.lDon't heat, recharge or bend battery.lWe take no responsibility for stolen ESLs without encryption.lKeep away batteries from children.lDon't throw defective batteries into the dustbin. Give them to a reprocessingcompany.lDon't throw electronic device into the dustbin. Give them to a reprocessingcompany.lContact imagotag GmbH for more details about this process.
Product Specification AP-2010Page 27 of 2713 WarrantyThe device is provided with a warranty seal. Is this warranty seal destroyed, expire at the sametime, all warranty claims.

Navigation menu