SES imagotag AP0002 digital network controller transceiver User Manual My

Download:
Mirror Download [FCC.gov]
Document ID	3356456
Application ID	LsHxl0N9BM1q/s4PnMJP1w==
Document Description	Product range description
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	158.91kB (1986352 bits)
Date Submitted	2017-04-13 00:00:00
Date Available	2017-04-13 00:00:00
Creation Date	2017-03-27 09:05:56
Producing Software	madbuild
Document Lastmod	2017-03-27 09:05:56
Document Title	My Document
Document Author:	map

Product
Specification
AP-2010
Last change: 27.03.2017
Product Specification AP-2010
Introduction
1.1 Key Features
1.2 Destination countries
1.3 Scope of delivery
Barcode Information
2.1 Serial Number
Mechanical Characteristics
3.1 Mechanical Dimensions
3.2 Front, Side and Top View
3.3 Upper Surface
3.4 Side View
3.5 Rear View
Mounting
10
4.1 Audience
10
4.2 General Instructions
10
4.3 Instructions for the Mounting Location
10
4.4 Approachability
11
4.5 Screw of the Antenna
11
4.6 Metal Bracket for Mounting on Wall, Ceiling or T-Mounting Rail
12
4.7 Mounting on Wall or Ceiling
12
15
Electrical Specifications
5.1 Used Channels
15
5.2 Difference WiFi and ESL protocol
15
5.3 Cabel Specifications
15
5.4 Power Supply Specifications
16
5.5 Pinout RJ45 Ethernet
16
Electrical & RF Characteristics
17
6.1 General Technical characteristics
17
6.2 Power and Current Consumption
17
6.3 General Specifications
17
19
Environmental
7.1 Humidity and Operating Conditions
19
Page 2 of 27
Product Specification AP-2010
7.2 Storage Conditions
19
7.3 Cleaning Instructions
19
20
Packing
8.1 Packing Dimensions
20
8.2 Illustrations
20
8.3 Palletization
21
22
Certifications
9.1 Types
22
9.2 Overview
22
9.3 Applied Standards
22
9.4 Declaration
22
10 Problems which requiring maintenance or replacement of the AP-2010
24
11 Intended Use
25
12 Improper Use
26
13 Warranty
27
Page 3 of 27
Product Specification AP-2010
Introduction
The Access Point AP-2010 by imagotag is a network device similar to WLAN access points that
is required for communication with the imagotag electronic shelf labels (transmits price
information to the labels).
Up to 10 000 labels can be managed per access point and the self-organizing network allows
automatic roaming of labels without manual handling. The high transmission rate of the 2.4
GHz wireless technology and the intelligent task scheduling enables fast and secure updates
on imago G1 labels of all sizes.
This document is the technical specification of the Access Point AP-2010.
In the USA and Canada the AP-2010 usa/canada bundle incl. antenna with limited data
efficiency is required according to the FCC/IC regulations. This bundle has a reduced data
efficiency for label/updates/hour, for more details see label product specification.
1.1
Key Features
1.2
Manages up to 10 000 imago G1 labels of all sizes
Covers up to 1 950 m² (depending on shop layout)
Low power consumption – powered by PoE (Power over Ethernet) or with low power plug
Easy configuration and monitoring
Optimized scheduling of tasks and self-managed roaming of labels
Destination countries
The imagotag AP-2010 is currently intended for use in Europe, Canada and USA. More countries
will follow.
1.3
Scope of delivery
1 pcs imagotag AP-2010
1 pcs 2.4-2.5GHz 5dBi antenna
1 pcs metal mounting
1 pcs “caddy® clips 4G16M11“ from Erico®
2 pcs self-locking nuts M6
May vary depending on configuration
Page 4 of 27
Product Specification AP-2010
Barcode Information
The AP-2010 comes with an AP-ID, P/N, MAC and S/N. The AP-ID consists of 5 decimal digits
(0-9).
Product Code: A1A001xxx
2.1
Serial Number
Depends on Producer (A)
2.1.1
Producer is 01
Part
Description Format Example Comment
Source
Specified by
imagotag once for
each fab
Producer
01
alpha
Product
family
G1B
alpha
Product
version
301
alpha
Product
revision
001
alpha
Separator
“-“
Internal
alpha
Internal
Year
1 dec 4
4=2014, 5=2015,...
Week
2 dec 10
Calendar week in current Calculated during
year (01-53)
production
Weekday
1 dec 3
Internal
5 dec 00060
Incremented on every
change of product
specification
Specified by
imagotag in the
product specification
document
Fixed
Continuous Serial
Number (Counter)
Page 5 of 27
Product Specification AP-2010
2.1.2 Producer is not 01
Part
Description Format Example Comment
Source
Specified by
imagotag once for
each fab
Producer
02
alpha
Product
family
R22
alpha
Product
version
N01
alpha
N = with NFC
Product
revision
001
alpha
Incremented on every
change of product
specification
Separator
“-“
Year
alpha
Week
2 dec 13
Internal
6 dec 000065
Specified by
imagotag in the
product specification
document
Fixed
E=2014, A=2010,
B=2011,..
Continuous Serial
Number (Counter)
Format:
AABBBCCCDDD-EFFGGGGGG
Example:
02G1B302001-E13000065
Calculated during
production
Note:
Calendar week date is calculated according to ISO 8601 (see http://en.wikipedia.org/wiki/ISO_week_date
Page 6 of 27
Product Specification AP-2010
Mechanical Characteristics
3.1
Mechanical Dimensions
3.2
With antenna:
o Outline (mm): 226 x 135 x 45
o Weight: 350 g
Without antenna:
o Outline (mm): 196 x 135 x 45
o Weight: 320 g
Front, Side and Top View
FIGURE 1-1: Front, side and top view of the AP-2010
1 Mounting plate fixation screwhole
3 Antenna socket
2 LED
4 Antenna
Page 7 of 27
Product Specification AP-2010
3.3
Upper Surface
FIGURE 1-2: Top view of the imagotag AP-2010
5 Connection for the Power Supply
8 Restart
6 LAN/PoE
9 Reset to Factory Settings
7 Console
3.4
Side View
FIGURE 1-3: Side view of the imagotag AP-2010
10 Antenna Connector (unused)
12 Snap Connector Housing
11 Warranty Seal
Page 8 of 27
Product Specification AP-2010
3.5
Rear View
FIGURE 1-4: Rear view of the imagotag AP-2010
13 Mounting Tab
17 Snap Connector Housing
14 Mounting Rail
18 Housing Screw
15 Locking Tab
19 Mounting Profile
16 Label
Page 9 of 27
Product Specification AP-2010
Mounting
4.1
Audience
The installation instructions are intended for trained electricians who can exhibit the following
qualifications:
4.2
Knowledge of the use of tools and work instructions.
Knowledge of the usable condition of the tool.
Knowledge of the electrical safety instructions.
Knowledge of the electrical building regulations.
Knowledge of the relevant standards.
Knowledge of assembly schedule.
General Instructions
Read these installation instruction carefully before you connect the access point to the
power source.
The company imagotag GmbH assumes no liability for injury to persons or damage to the
Access Point or damage to the environment caused by improper installation or misapplication.
Remove jewellery such as rings, necklaces, and watches before working on the device.
Make sure that the access point is not connected to the power source during assembly.
Don’t work on the access point during a thunderstorm and don’t connect a cable at this
time.
Use appropriate and tested climbing aid if you work above body height.
Complete the installation and use the ERICO products just according the
ERICO® instruction. If necessary, you will find the desired data sheets at
www.erico.com and at every ERICO customer service.
4.3
Instructions for the Mounting Location
The Access Point could be mounted on a:
Concrete wall
Mortar wall
T-Mounting Rail
Select the installation location for the access point carefully. Pay particular attention to the
following requirements:
Install the access point only in areas where the permissible environmental conditions
(see ) can be observed.
Don’t install the access point in environmental with direct sunlight or heat source.
Mount the metal bracket for the access point on dry surfaces only.
Page 10 of 27
Product Specification AP-2010
4.4
Don’t mount the access point on any flammable material.
The minimum bearing capacity of the substrate should be 5 kg.
The LAN cable manufacturer must be complied with the default specifications (e.g. minimum bend radius)
Approachability
Mount the metal bracket that the access point can easily be pushed into the metal
bracket
Make sure that the LAN socket is easily accessible after installation.
After installation the LED should be clearly visible.
It is important that the inner surface of the access point have sufficient air circulation.
The vents must be free to ensure good ventilation and prevent overheating.
The mounting material (e.g. screws or pegs) for securing the metal bracket on
concrete wall is not part of the scope of delivery. It must be selected by the
installer depending on the substrate itself.
4.5
Screw of the Antenna
FIGURE 1-5: Figure 3 - Screw of the Antenna
1 Front Part
3 Direction of Rotation
2 Connection Socket
4 Rear Part (Swivelling)
Note: Screw the antenna with only the front part (1)
Page 11 of 27
Product Specification AP-2010
4.6
Metal Bracket for Mounting on Wall, Ceiling or T-Mounting Rail
Once the metal bracket is mounted, the AP-2010 will be mechanical connected and fixed with a
fixing screw.
FIGURE 1-6: Figure 4 - Metal Bracket for imagotag AP-2010
4.7
Mounting on Wall or Ceiling
FIGURE 1-7: Figure 5 - Wall or Ceiling Mounting (Scheme)
0 Mounting Surface
3 imagotag AP-2010
1 Metal Bracket
4 Fixation Screw
2 Mounting Screw
a. Install the metal bracket to the wall or ceiling with the help of dowels and mounting
screws.
Page 12 of 27
Product Specification AP-2010
FIGURE 1-8: Figure 6 - imagotag AP-2010 Locking Tabs
b. Slide the access point to the mechanical lock of the locking tabs
c. Attach the AP-2010 with the enclosed fixation screw to the metal bracket
4.7.1 Mounting on a T-Mounting Rail
Attach the metal bracket using the included “caddy® clips” from Erico® and the enclosed, selflocking screw nuts M6.
FIGURE 1-9: Figure 7 - Mounting an AP-2010 on a T-Mounting Rail
0 T-Mounting Rail
3 imagotag AP-2010
1 Metal Bracket
4 Fixation Screw
2 Self-locking Screw Nuts M6
5 ERICO® „caddy® clips“
a. Place 2 pieces of “caddy® clips” with the right distance on the T-Mounting Rail and fix it
(twist)
Page 13 of 27
Product Specification AP-2010
b.
c.
d.
e.
Place the metal bracket
Fix the Metal Bracket with 2 pieces of the self-locking screw nuts M6
Slide the access point to the mechanical lock of the locking tabs
Attach the AP-2010 with the enclosed fixation screw to the metal bracket
Page 14 of 27
Product Specification AP-2010
Electrical Specifications
5.1
Used Channels
Although WIFI and ESL use the same frequency band (2.4 Ghz ISM Band), there are channels
that do not overlap (not interfering - recommended channels).
Kanal Frequenz WLAN Kanal (802.11b/g)
10
2404 MHz
2010 MHz
2422 MHz
2425 MHz
2442 MHz
2445 MHz
2462 MHz
2470 MHz
2474 MHz
2477 MHz
2480 MHz
WLAN 1 (2402 – 2422 MHz)
not interfering
WLAN 6 (2427 – 2447 MHz)
not interfering
WLAN 11 (2452 – 2472 MHz)
not interfering
not interfering
not interfering
FIGURE 1-10: Overview of used channels of the imagotag AP-2010
5.2
Difference WiFi and ESL protocol
In contrast to the proprietary developed time based imagotag ESL protocol the WiFi protocol
applies to the IEEE 802.11 standard.
FIGURE 1-11: WiFi and ESL frequencies and channels (22 Mhz bandwidth)
5.3
Cabel Specifications
You can use a commercially available LAN cable (CAT-5 or higher) for data connection and the
power supply (if PoE is used) of the imagotag AP-2010.
Page 15 of 27
Product Specification AP-2010
5.4
Power Supply Specifications
Sunny Computer Technology Europe s.r.o.
5.5
Model: SYS1541-1505-Wxx
Input: 100-240 V ~ 1.0 A MAX, 50-60Hz
Output: 5V 3A
Output Power: 15W MAX
Operating Temperature: 0° C to + 40° C
MTBF: 50.000 hours full rated load operation at 40 ℃, according to the MIL-HDBK-217F
Pinout RJ45 Ethernet
Pin 3 – TX (AP to PC)
Pin 6 – RX (PC to AP)
Pin 4/5 – Ground
5.5.1 Pinout
Page 16 of 27
Product Specification AP-2010
Electrical & RF Characteristics
6.1
General Technical characteristics
Power:
l External Power Supply: 5 VDC / 3A
l Power Supply via PoE: IEEE 802.3af, IEEE 802.3at
l Power consumption: 15W MAX, typical 3W
Technology:
l Radio technology: proprietary
l Operating frequency: 2.4 GHz (ISM-Band) – 2.4835 GHz
l Transmitted power: ≤ 10 dBm
l Number of Channels: 11
l Access protocol: proprietary
Other:
6.2
MTBF: >300.000h at 40°C according to SN29500
Power and Current Consumption
Power consumption measurements indicate that the AP-2010 has the following patterns:
l Operating Current: ≤ 60 mA (max. current)
l Operating Power: ≤ 280 mW
l Supply Voltage: 5V ± 10%
6.3
General Specifications
6.3.1 Hardware
600 MHz ARM Cortex-A8
Memory - 512MB DDR2 memory
SD/MMC card connector
o 512 MB card with imagotag software preinstalled
Power over Ethernet (PoE IEEE 802.3af / IEEE 802.3at)
o The original IEEE 802.3af-2003 PoE standard provides up to 15.4 W of DC power
(minimum 44 V DC and 350 mA to each device). Only 12.95 W is assured to be available at the powered device as some power is dissipated in the cable.
Other Interfaces
o Serial RS232 Interface
o 10/100 Ethernet Interface
Power
o Power source options (DC, PoE)
o 3.3 V I/O operation
o DC supply 5V ± 10%, 3A Max
Page 17 of 27
Product Specification AP-2010
6.3.2 Software Package
OS: Embedded Linux
AP-2010 application software
RF Firmware
Page 18 of 27
Product Specification AP-2010
Environmental
7.1
Humidity and Operating Conditions
7.2
Storage Conditions
7.3
Temperature: 0° C to + 40° C
Humidity: 10% to 80% (non-condensing)
Temperature: -20 °C to + 70 °C
Humidity: 10% to 85% (non-condensing)
Cleaning Instructions
Steps:
1. Shutdown Access Point
2. Plug Out Power Supply (AC or PoE)
3. Clean the Access Point with the help of a damp cloth
Note: Do not use liquid or aerosol cleaners.
Page 19 of 27
Product Specification AP-2010
Packing
8.1
Packing Dimensions
DIMENSIONS
LENGTH
BOX
520
PALLET 1200
UNIT
1200
WIDTH
350
800
800
HEIGHT
260
140
960
STACKING
QUANTITY
LAYER / UNIT 3
BOXES / LAYER 4
BOXES / UNIT 12
SETS / BOX
10
SETS / LAYER 40
SETS / UNIT 120
Imagotag AP-2010 / Box: 10
8.2
Illustrations
Page 20 of 27
Product Specification AP-2010
8.3
Palletization
Page 21 of 27
Product Specification AP-2010
Certifications
9.1
Types
Housing, board and the display are conform with the ROHS Directive
The product meets the EU safety, health and environmental protection
requirements and has the approval of CE marking
This device complies with part 15 of the FCC Rules.
9.2
Overview
Caption
RoHS
AP-2010
Food
Contact
•
CE
FCC/IC
•2
•5
1FCC/IC certified since calendar week 9 / year 2015 (the FCC logo must be printed on the nameplate)
2R&TTE EN 300328 V1.8.1
3R&TTE EN 300328 V1.9.1
5There are two different versions of the AP available. One CE and one FCC version.
9.3
Applied Standards
Information Technology Equipment
EN 60950-1/A2:2013
UL 60950-1/A2:2014
CSA CAN/CSA-C22.2 NO.60950-1-07
EMV
EN 301489-17 V2.2.1
R&TTE
EN 300328 V1.8.1 / EN 300328 V1.9.1
Human Exposure to Electromagnetic Fields
EN 62479:2010
Radio international
FCC: 47 CFR Part 15 (USA)
RSS-210 Issue 8 (Canada)
9.4
Declaration
The company imagotag GmbH declares on his own responsibility that the AP-2010 corresponds
to the standards mentioned above.
9.4.1 FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
Page 22 of 27
Product Specification AP-2010
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the authority to operate the equipment.
9.4.2 IC
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
9.4.3 NCC 警 語 :
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停
用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工
業、科學及醫療用電波輻射性電機設備之干擾。
Page 23 of 27
Product Specification AP-2010
10
Problems which requiring maintenance or replacement of
the AP-2010
Plug out the power supply and contact the imagotag GmbH when it comes to the following
cases:
l The AP-2010 was strewn with liquid.
l The AP-2010 has been dropped or damaged.
l The LAN port of the AP-2010 is damaged.
l The antenna connection thread is damaged.
l The LED of the AP-2010 no longer lights up.
Contact the manufacturer if despite intended purpose the device is not working and none of the
mentioned cases occurred.
Page 24 of 27
Product Specification AP-2010
11
Intended Use
The imagotag AP 2010 is exclusively designed to connect to electronic labels of the company
imagotag GmbH via radio.
The device may only be used in areas where the environmental conditions be the same as
descripted in the chapter (see Environmental on page 19).
Intended use includes the observance of all information in this system manual.
Page 25 of 27
Product Specification AP-2010
12
Improper Use
Any use that is not mentioned in Section Intended Use, shall be deemed to be improper. Any
damage which result from improper use, the operator will assumes liability.
The following usage is not allowed:
Never dismantle the electronic device because except battery there is no component which could be changed by someone who is not qualified.
Don't drop it.
Keep it away from water.
Strictly avoid direct contact with groceries.
Don’t use the electronic device with defective parts.
Don’t use the electronic device with spare parts and accessories which are
not examined and approved by the imagotag GmbH.
Unauthorized changes or modifications to the electronic device and their components without the consent of imagotag GmbH are not allowed.
Don't heat, recharge or bend battery.
We take no responsibility for stolen ESLs without encryption.
Keep away batteries from children.
Don't throw defective batteries into the dustbin. Give them to a reprocessing
company.
Don't throw electronic device into the dustbin. Give them to a reprocessing
company.
Contact imagotag GmbH for more details about this process.
Page 26 of 27
Product Specification AP-2010
13
Warranty
The device is provided with a warranty seal. Is this warranty seal destroyed, expire at the same
time, all warranty claims.
Page 27 of 27

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 27
Page Mode                       : UseOutlines
Language                        : en-us
Producer                        : madbuild
Create Date                     : 2017:03:27 09:05:56+02:00
Modify Date                     : 2017:03:27 09:05:56+02:00
Title                           : My Document
Author                          : map
Subject                         : 

EXIF Metadata provided by EXIF.tools