SIGFOX SNT114 sigfox demonstrator User Manual SNT1 1 quick start guide v3

Download:
Mirror Download [FCC.gov]
Document ID	3463021
Application ID	wjbYIKx6Ylf6N+uR5BeMew==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	42.7kB (533775 bits)
Date Submitted	2017-07-13 00:00:00
Date Available	2017-07-13 00:00:00
Creation Date	2017-07-13 09:41:09
Producing Software	PDFCreator 2.3.2.6
Document Lastmod	2017-07-13 09:41:09
Document Title	SNT1.1 quick start guide_v3
Document Creator	PDFCreator 2.3.2.6
Document Author:	HeleneArdiller

GEN-PMT-GUI03-SNT_user_guide_quick
SNT 1.1
User Guide
February 2017
Revision history:
Rev.
Date
Author
Change description
0.1
08/02/2017
A. Trombetta
Preliminary version
0.2
13/02/17
A. Trombetta
Tables of command and LED
0.3
16/02/2017
A. Trombetta
SNT photo
0.4
20/02/17
A. Trombetta
Added command to table
0.5
22/02/17
A. Trombetta
Clarify display type in backend
1.0
16/05/17
A. Trombetta
SNT 1.1
Contents
I.
INTRODUCTION ....................................................................................................................................... 4
II.
REQUIREMENTS ...................................................................................................................................... 5
1.
2.
3.
4.
III.
RADIO CONSIDERATIONS .................................................................................................................................. 5
CABLE CONNECTION ....................................................................................................................................... 5
SOFTWARE REQUIREMENTS .............................................................................................................................. 5
REGISTRATION IN THE BACKEND ........................................................................................................................ 6
SNT OPERATIONAL MODES ..................................................................................................................... 6
1.
A.
B.
C.
2.
3.
IV.
STANDALONE ................................................................................................................................................ 6
Uplink sequence ................................................................................................................................... 7
Bidirectional sequence ......................................................................................................................... 7
Uplink frame format ............................................................................................................................. 8
SERIAL AT COMMANDS OPERATION ................................................................................................................... 8
LED RECAPITULATIVE TABLE ............................................................................................................................. 9
WARNING STATEMENTS ........................................................................................................................ 10
1.
2.
3.
FCC: ......................................................................................................................................................... 10
IC ............................................................................................................................................................. 10
CE ............................................................................................................................................................ 11
I. Introduction
Sigfox Network Tester (SNT), is a Sigfox device provided exclusively for
technology evaluation and network coverage reference measurements.
Its primary functionality consists in periodic transmission of Sigfox radio messages
meant for reception at any Sigfox Access Points. Each SNT has a unique network
identity, printed on a sticker at the back and stored into its memory. With this ID, full
retrieval of the device activity is possible through the OSS portal.
SNT 1.1 is available in 4 versions to cover worldwide RF requirements:
SNT1.1-1, SNT1.1-2, SNT1.1-3, SNT1.1-4
Antenna
LED
ON/OFF button
Micro USB port
II. Requirements
1. Radio considerations
SNT serves as reference device. It is equipped with a 1⁄2 wave antenna. For reference
performance level, classical radio precautions have to be observed during operation:
antenna vicinity has to be cleared of any metallic object, and antenna shall be kept in
vertical position.
Note that Sigfox Network optimal performance is obtained in stationary operation.
2. Cable connection
SNT comes with a micro USB to USB cable.
SNT is equipped with a rechargeable battery. When the device is connected to a USB
charger or a USB socket of a computer, it will start to charge automatically (blue
LED). The device can be used while charging.
The battery takes about 3 hours to fully charge.
SNT can be used and controlled by computer using the same USB cable. In this case,
check the Software requirements (below).
3. Software requirements
SNT is controlled by AT commands and works with Windows, Linux and Mac. Just
make sure you to have:
• FTDI drivers installed on your computer
• Any soft to open serial port like Putty for Windows, Screen or Cutecom on
Linux
See SNT drivers installation guide for detailed information.
4. Registration in the Backend
Each device needs to be registered in the OSS Portal (Backend interface).
In Device type configuration, you can configure the display type.
Depending on how you will use your SNT, you can configure it like this:
•
To have GPS location displayed in the Backend, select in Type: Geolocation
and Default [Root] :
•
To get information about battery and frame counter, select Type : Custom
and Custom configuration with :
Vdd::uint:16 NA::uint:16 NA1::uint:16 NA2::uint:16 CounterDL::uint:16
CounterUL::uint:16
III. SNT operational modes
SNT has two operational modes: standalone and serial communication.
The device shall be used hand-held in upright position only. Alternatively the device
may be used when put on the desk or an supporting structure.
The device is not designed and must not be used nearby body like belt-worn, lanyard
around the neck or put into pocket.
1. Standalone
Pressing the button for a few seconds will activate the device. The LED lights blue as
the device turns on. Then the device will execute the sequences described below.
SNT has two main options: monodirectional (uplink only) and bidirectional sequences
(uplink and downlink).
By default, SNT is set to Uplink mode. These modes can be set by AT commands
(see next chapter).
These sequences are looped 10 times, then device shuts down automatically.
A. Uplink sequence
Just after powering up, SNT sends a SIGFOX message every 10 minutes by default.
This option can be set by AT commands. This message contains GPS information if
available.
When SNT is sending, green led is blinking.
Between two messages, SNT led can be of one of these two colours:
• Green if internal GPS is fixed
• Orange if it is not the case
B. Bidirectional sequence
In this mode the device is sending and receiving frames. The LED colour is pink.
The sequence is:
1. TX :
device sending an uplink message.
2. IDLE:
device in wait state (20 seconds)
3. RX:
device in receive mode (timeout after 25 seconds)
Depending on the reception result, there are two possible cases:
> case 1: sequence completion by successful downlink frame reception
4. Led blinking in green, indicating successful message reception and send an
OOB message
5. Link quality indication is displayed for 10sec (details below)
Or
> case 2: sequence completion timeout after 25 secs (NO frame received)
4. LEDs blinking in RED 3 times (~6seconds)
Link quality indication:
Providing the Backend direct callback is used and includes uplink RSSI, the link quality
is flashed using a LED code:
•
LINK QUALITY = VERY GOOD
→ Blinks 3 times (WHITE)
•
LINK QUALITY = GOOD
→ Blinks 2 times (WHITE)
•
LINK QUALITY = AVERAGE
→ Blinks 1 time (WHITE)
Note: The white LED may appear slightly pink.
C. Uplink frame format
SIGFOX payload is composed of 12 bytes. The format of payload is available in the
following table.
Note: Vdd in mV
2. Serial AT commands operation
AT commands can be sent to the device by connecting the USB cable to a computer
and opening a serial interface.
All the basics available commands are listed here:
Commands
Responses
Descriptions and comments
Default
values
AT
OK
Attention command. Just to be sure that all
works fine!
AT?

OK
Requests summary of available AT commands
AT&V

Display device version information (SNT type,
SW version, ID, PAC)
AT$SF=,
OK
Change number cycle before shutdown.
Value > 0. Or 0 for infinite
10
Current value
10
AT$NC?
AT$BI=
OK
AT$BI?
AT$ID=
OK
AT$ID?
AT$GPS=
OK
AT$GPS ?
AT$FSD=
Current value
Change inter-message delay in seconds.
0 < Value < 65536
Current value
Enable (1) or disable (0) GPS.
Value 0 improve SNT battery life
600
600
OK
Current value
Enable (1) or disable (0) OneTouch mode
(describe bellow)
Current value
OK
Enable (1) or disable (0) Factory reset. You
need restart after with “ATR\r” command
OK
AT$OT?
AT$FP=
Current value
Set Delay before first message (in second)
0 < Value < 65536
AT$FSD ?
AT$OT=
Enable (1) or disable (0) bidirectional mode
AT$FP?
Current value
ATR
Soft reset
AT$OT for OneTouch
When this command is at 1, the SNT send only one Sigfox message instantly after
having pushed the button.
This frame is: “HELLO WORLD!” in ASCII.
3. LED recapitulative table
Here is a recapitulative of the lights’ sequences and their meanings:
Mode
On
Uplink mode
sequence
LED colour
Meaning
Blue
Device turning on
Green
Sending 3 frames
Flashing orange
Searching GPS
Flashing green
GPS found
Green blinking x3
Sending 3 frames
Flashing pink
Waiting for Backend response
Green Flashing x1
flashing x3
Successful msg reception + send
OOB msg
Very good link quality
flashing x2
Good link quality
flashing x1
Limit link quality
Bidirectional mode
sequence
Red flashing x3
Failed to receive frame
Slow flashing pink
Idle time before new cycle
Off
Red
Device turning off
Connected
Fixed blue
Device charging or charged
IV. WARNING STATEMENTS
1. FCC:
This device complies with Part 15 of the FCC Rules.
• Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
• The radiated output power of the device is far below the FCC radio frequency
exposure limits. Nevertheless, the device shall be used in such a manner that
the potential for human contact during normal operation is minimized.
• Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
2. IC
English
This device complies with Part 15 of the FCC Rules and with Industry Canada licenseexempt RSS standard(s).
Operation is subject to the following two conditions:
this device may not cause harmful interference, and
this device must accept any interference received, including interference that may
cause undesired operation.
Français
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
10
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
3. CE
Do not throw away in the normal household waste. The device must be disposed of
in the same way as other electronic equipment following local procedures.
4. Japan
Japanese Radio Law and Japanese Telecommunications Business Law Compliance.
This device is granted pursuant to the Japanese Radio Law (電波法) .
This device should not be modified (otherwise the granted designation number will
become invalid).
sigfox
425 rue Jean Rostand, 31670 Labège, France
www.sigfox.com
The information presented is subject to change without notice. Sigfox assumes no responsibility for inaccuracies contained herein.
Sigfox and the sigfox logo are trademarks of Sigfox. All other trademarks are the property of their respective owners.
Copyright ©2017 sigfox. All right reserved
11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2017:07:13 09:41:09+02:00
Modify Date                     : 2017:07:13 09:41:09+02:00
Author                          : HeleneArdiller
Subject                         : 
Page Count                      : 11
Page Layout                     : SinglePage
Page Mode                       : UseNone
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:22a19214-69fa-11e7-0000-9b82dd44d1b3
Producer                        : PDFCreator 2.3.2.6
Keywords                        : 
Creator Tool                    : PDFCreator 2.3.2.6
Document ID                     : uuid:22a19214-69fa-11e7-0000-9b82dd44d1b3
Format                          : application/pdf
Title                           : SNT1.1 quick start guide_v3
Creator                         : HeleneArdiller
Description                     : 

EXIF Metadata provided by EXIF.tools