SISTEMATICA S p A RTXTREND Professional Remote Control suitable for Industrial and/or Vehicle Applications User Manual Transmitter EASYRTX TRENDRTX REV 3a

SISTEMATICA S.p.A. Professional Remote Control suitable for Industrial and/or Vehicle Applications Transmitter EASYRTX TRENDRTX REV 3a

manual

SISTEMATICA S.p.A.  REV.3a Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. +39 0175 255.711 r.a. – Fax +39 0175 255.715 http://www.sistematica.it          e-mail: info@sistematica.it   28/03/2012        EASYRTX - TRENDRTX    RADIO REMOTE CONTROL TRANSMITTER  USER AND MAINTENANCE MANUAL           WARNINGS  This  manual  is  an  essential  part  of  the  device  and  it  should  be  thoroughly  kept  for  later  consultation. Carefully read the warnings contained in this manual, concerning safety and a proper preservation of the product.  These warnings  are  ALWAYS to  be  carefully read  before  using  the  device. SISTEMATICA  S.p.A. declines all responsibility  for any trouble  arising from the non-compliance with these warnings.  • AVOID  ATTEMPTING  TO  REPAIR  THE  DEVICE  BY  YOURSELF.  REPAIRS  PERFORMED  BY UNSKILLED  PEOPLE  CAN  CAUSE  SERIOUS  DAMAGES  OR  FAILURES.  FOR  ASSISTANCE, APPLY TO YOUR LOCAL AUTHORIZED SERVICE CENTRE. USE ONLY ORIGINAL SPARE PARTS. • ALWAYS KEEP AT A SAFE DISTANCE FROM THE MOVING PARTS. • KEEP THE RADIO CONTROL OUT OF THE CHILDREN’S REACH.
 SISTEMATICA S.p.A.  Pag. 2/4 Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. +39 0175 255.711 r.a. – Fax +39 0175 255.715 http://www.sistematica.it          e-mail: info@sistematica.it   TECHNICAL FEATURES  EASYRTX •  Manufacturer: SISTEMATICA S.p.A. •  Number of commands: da 2 a 6 •  Dimension (in mm): 109 x 56 x 30  •  IP protection: IP67 •  Operating temperature: -20°C ÷ +70°C •  Battery supply: n°2 AAA Alkaline 1,5V cell •  Quiescent absorption: 1 µA •  Back lighted keypad •  Safetypoint •  Tilting-hand •  Buzzer •  Working distance: 100÷150 m in free fiel condition TRENDRTX •  Manufacturer: SISTEMATICA S.p.A. •  Number of commands: da 4 a 24 •  Dimension (in mm): 165 x 80 x 40 •  IP protection: IP67 •  Operating temprature: -20°C ÷ +70°C •  Battery supply: n°2 AA Alkaline 1,5V cell •  Quiescent absorption: 5 µA •  Back lighted keypad •  Active Safetypoint •  Tilting-hand •  Buzzer •  Working distance: 100÷150 m in free fiel condition  INSTRUCTIONS FOR USE  RADIO REMOTE CONTROL 6÷14 FUNZIONI (EASYRTX E TRENDRTX)  RADIO REMOTE CONTROL UP TO 24 FUNZIONI (ONLY TRENDRTX) 1.  Switch on the receiver; 2.  Wait for a few second (self testing); 3.  Press START key to allow the system to receive the transmission (the system stay active for n.2 minutes after  the  last  control  has  been  given,  after  wich  it reset.. Then press  START key again to restart the system); 4.  Press the required key on the trasmitter to activate the related output on the receiver EXAMPLE: KEY 1 → OUT1 + M.O. + EM. ↓ EXAMPLE: KEY 6 → OUT6 + M.O. + EM. ↓ EXAMPLE: KEY 14 → OUT14 + M.O. + EM. 5.  Press  the  STOP  key  to  inhibit  the  controls reception. In this phase all the controls are reset. To activate again the system press START. EASYRTX  TRENDRTX   1.  Switch on the receiver; 2.  Wait for a few second (self testing); 3.  Press  START  key  and  key  1  at  the  same  time  to enable the output on the receiver unit from 1 to 12 (I° page); press the required key on the transmitte r to activate the related output on the receiver: EXAMPLE: KEY 1 → OUT1 + M.O. + EM. ↓ EXAMPLE: KEY 12 → OUT12 + M.O. + EM. 4.  Press  START  key  and  key  2  at  the  same  time  to enable the output on the receiver unit from 13 to 24 (II° page); press the required key on the transmitt er to activate the related output on the receiver: EXAMPLE: KEY 13 → OUT13 + M.O. + EM. ↓ EXAMPLE: KEY 24 → OUT24 + M.O. + EM. 5.  Press  the  STOP  key  to  inhibit  the  controls reception. In this phase all the controls are reset. To activate again the system  press START and key 1 or key 2 depend on output want activate. NOTE:  The  24  function  transmitter  is  composed  by  2 pages. First page enable first 12 outputs (OUT 1 ÷ OUT 12);  second  page  enable  last  12  outputs  (OUT  13  ÷ OUT 24).
 SISTEMATICA S.p.A.  Pag. 3/4 Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. +39 0175 255.711 r.a. – Fax +39 0175 255.715 http://www.sistematica.it          e-mail: info@sistematica.it   MEANING OF THE TRANSMITTER LED  The remote control has 3 leds used to indicate the operation of the system. The following table descrive the various meanings. LED  OPERATION  MEANING Flashes  Button pressed Flashes each 5 sec.  Link radio e START OK Flashes each 3 sec.  Button held down Flashes once per sec.  Link radio KO GREEN Flashes twice per sec.  Link radio loss Flash Transmitter out of the magnetic field SafetyPoint-Plate by pressing a button on safetypoint SAFETYPOINT Flash Transmitter  for  5  sec  in  the  magnetic  field Safetypoin-plate without pressure of any key Flashes once every 2,5 sec.  I° page selected YWLLOW CAMBIO PAGINA  Flashes twice every 2,5 sec.  II° page selected Flashes once per sec. if button held down  Low battery RED  On if button held down  Low battery (replace battery)  SYSTEM CODING  Coding the system is an operation that is only necessary when the receiver has to be replaced or you want to use it with a different SISTEMATICA radio remote control from the one it is coupled with at the time of purchase.  To recode the system, consult the user manual of the receiver coupled with the transmitter.  REPLACING THE BATTERIES IN THE TRANSMITTER  If the red LED on the handset flashes when the key is held down, it means that the batteries are almost flat (<2,5 V). In this situation, replace the batteries as soon as possible since the system performance may be impaired. When the voltage reaches values lower than 2,2 V, the red LED stays on when the key is pressed. In this situation, replace the batteries,  as  it  is  not  possible  to  give  commands  to  the  output  ports.  To  replace  the  batteries  follow  these instructions: 1.  Obtain n°2 “AA” 1.5V  alkaline batteries; 2.  Open the battery compartment by unscrewing the two screws; 3.  Remove the flat batteries from their holder; 4.  Insert the new batteries paying attention to the polarity shown on the end. Before going ahead with closing the battery compartment, made sure the green LED emits a flash each time a key is pressed; 5.  After checking that the transmitter is working properly, colse the container.   The  remote  control  contains  miniaturized  electronic  circuitry,  and  so  we  recommended  taking grat care when following the instructions for replacing the batteries, handling things delicately in a clean area.  The use of zinc-carbon batteries is not advised, as these suffer from greater self-discharge than alkaline batteries.  Do not use rechargeable batteries.
 SISTEMATICA S.p.A.  Pag. 4/4 Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. +39 0175 255.711 r.a. – Fax +39 0175 255.715 http://www.sistematica.it          e-mail: info@sistematica.it   PRODUCT IDENTIFYING LABELS  EASY RTX  TREND RTX EXTERNAL  INTERNAL  EXTERNAL    nnnnn: product model S/N: product serial number Cod.: product identification number  Product serial number  nnnnn: product model S/N: product serial number Cod.: product identification number  PROBLEM IDENTIFICATION AND SOLUTION  PROBLEM  POSSIBLE CAUSES  SOLUTIONS The  green  LED  on  the transmitter does not light when a key is pressed  Flat batteries Flat batteries -Replacement  of  the  remote  control  batteries (see  “REPLACING  THE  BATTERIES  IN  THE TRANSMITTER”) Incorrect replacement of the batteries -Check  that  the  batteries  have  been  inserted correctly;  if  necessary  replace  them  (see “REPLACING  THE  BATTERIES  IN  THE TRANSMITTER” The  system  does  not  respond to the control System not coded  -Re-code the system (see “SYSTEM CODING”)  CE MARK     Declaration of conformity for Sistematica S.p.A. products can be required at: info@sistematica.it   This product may be subjected to usage restriction. Please contact info@sistematica.it for any further questions.  FCC STATEMENTS  These devices complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) these devices may not cause harmful interference and (2) these devices must accept any interference received, including interference that may cause undesired operation.  NOTE: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to these equipment. Such modifications could void the user’s authority to operate the equipments.  SISTEMATICA S.p.A. Grantee Code: O8I   EASYRTX label example FCC ID: O8IRTXEASY  TRENDRTX label example FCC ID: O8IRTXTREND

Navigation menu