SKYPINE ELECTRONICS SD9614SV CAR DVD ENTERTAINMENT CENTER (BLUETOOTH PORTION ONLY) User Manual SD 9614 SV

Download:
Mirror Download [FCC.gov]
Document ID	939327
Application ID	+vwBdIkl9Z8mAVNb3IqQbw==
Document Description	USERS MANUAL 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	242.87kB (3035869 bits)
Date Submitted	2008-05-09 00:00:00
Date Available	2008-05-09 00:00:00
Creation Date	2008-01-24 14:21:28
Producing Software	Corel PDF Engine Version 1.0.0.458
Document Lastmod	0000-00-00 00:00:00
Document Title	SD-9614-SV.cdr
Document Creator	CorelDRAW 版本 12.0
Document Author:	JUJUMAO

In Car Audio，
ʹ
[ek-san-ik]means
Sonic Excellence by
Mobile Entertainment
EXONIC Mobile Entertainment
Buena Park,CA. 90621 U. S. A .
www.exonicmobile.com
INSTRUCTION MANUAL
EXD 7090
Motorized 7"Touch Screen In-Dash Multimedia Disc Player
EXD7090
General information
Precautions
Installation instructions
Making the electrical connections
Installing the main unit
After installation and connections
10
Operation instructions
11
Detaching the front panel
11
Resetting the unit
11
Control elements
12
Main unit
12
Remote
15
Main Access Menu
17
Touch Screen
17
AM/FM Tuner Operation
20
DVD Operation
22
CD Operation
24
MP3 Operation
26
iPod Operation
27
SD Card Operation
30
JPEG Operation
31
Bluetooth Operation
31
Settings
Manufactured under license from Dolby Laboratories.
''Dolby''and the double-D symbol are trademarks of Dolby laboratories.
Features
34
System GENERAL Setup Menu
34
General Setup Menu
34
Adjusting RADIO Frequency
35
Adjusting the Clock
36
Audio Signal Processing (ASP)
37
System SCREEN Setup Menu
38
Screen Setup Menu
38
Setting TFT Brightness
39
Setting TFT Angle
40
Touch Screen Calibration
41
DVD setup menu
42
DVD Setup Menu - Language
42
DVD Setup Menu - Video
43
DVD Setup Menu- Ratings
44
Troubleshooting
46
IR Remote Preparation
49
General information
Specifications
Caution
50
51
Features
Thank you purchasing this EXONIC Multimedia Disc Player. Please read this information carefully and
follow all the instructions outlined below. This will ensure reliable operation and durability of your unit.
Keep the packaging and operating instructions in a safe place in order to pass them on to a subsequent
owner in the event of selling the unit at a later date.
Motorized 7" Touch Screen In-dash Multimedia Disc Player
Innovative in-dash monitor design allows the unit to be mounted in a single DIN slot. At the touch of a
button, a 7-inch wide-aspect-radio screen slides out, for comfortable DVD viewing.
High brightness and wide viewing angle monitor.
Touch panel user interface.
DVD, CD, VCD playback compatibility
Compatible with various disc formats, such as DVD-R/-RW, DVD+R/+RW, etc.
iPod
Control and command of most iPods via touch screen displays all information play lists.
Bluetooth
Hands-free phoning with cellular phones featuring Bluetooth technology
Answer and place calls via touch screen
One-touch dialing from phone book
On-screen caller ID
AM/FM Tuner
Auto/Manual search for radio station and preset station memory.
30 preset radio stations (12AM+18FM)
Distance/Local radio station seeking
Radio station scan playing.
Integrated SD card reader
4.1 Audio outputs, 1 Audio/video input, 1 Rear camera input, 1 Multi-zone A/V output and 1Composite
video output provided.
Precautions
To avoid the risk of injury or accident, read the following precautions before installing and operating the
unit.
On safety
Comply with your local traffic rules and regulations.
While driving
You must not watch or operate the monitor. It may lead to distraction and cause an accident. Park your car
in a safe place to watch the monitor and operate the unit.
While operating
Do not insert your hands, fingers or foreign object into the unit while the monitor is functioning. It may
cause injury or damage to the unit.
Keep small articles out of the reach of children. If your car was parked in direct sunlight resulting in a
considerable rise in temperature inside the car, allow the unit to cool off before operating it.
Preventing accidents
The video pictures appear only after you park the car and set the parking brake.
When the car starts moving, the video pictures automatically disappear for safety reasons, after
displaying the following caution.
Do not watch the monitor while driving. You may cause a traffic accident if your attention is distracted by
When installing, be sure not to damage any car parts such as pipes, tubes, fuel tank or wiring by using a
drill. It can cause a fire or an accident.
Do not attempt to open or repair the device yourself. This work should be performed by an authorized
service agent.
the monitor.
Installing location
CAUTION
Do not install this unit where:
IT'S UNLAWFUL TO OPERATE A VEHICLE WHILE VIDEO IS DISPLAYED IN THE
The driver’s view will be obstructed when the monitor is in either open or close position.
DRIVERS VIEWING AREA.
The operation of the car or the airbag system will be obstructed.
ENGAGE EMERGENCY BRAKE TO ENJOY VIDEO
It will obstruct the operation of the vehicle, especially the steering wheel, shift lever or brake pedal.
Do not use the System Setup feature while driving, or perform any other function which could divert your
Notes:
attention from the road.
If you experience problems during installation, contact your nearest EXONIC dealer.
When you connect the back camera:
If the unit malfunctions, reset the unit as described on page 11 first. If the problem still persists,
When you drive, watch the surroundings carefully for your safety. Do not depend on the back camera
contact your nearest EXONIC dealer.
exclusively.
When backing up you car, be sure to look back for your safety.
Do not touch the liquid crystal fluid if the LCD is damaged or broken. The liquid crystal fluid may be
hazardous to your health or fatal. If the liquid crystal fluid from the LCD contacts your body or clothing,
wash it off with soap immediately.
On installation
Due to its technical nature, it is highly recommended that your EXONIC EXD 7090 is installed by a
Moisture condensation
When the temperature of the unit falls (as in winter), the liquid crystal inside the screen will become darker
than usual. Normal brightness will return after using the monitor for a while.
To maintain high sound quality
Be careful not to splash juice or other soft drinks onto the unit or discs.
professional installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative
Playable discs
ground only.
The following types of discs/files are compatible:
If you try to install this unit by yourself, refer to the supplied “Installation/Connections” manual and read it
CD-ROM (ISO), CD-R, CD-RW, DVD+R/RW, DVD-R/RW
carefully. Make sure to install this unit properly.
CD-DA, DVD Video
Improper installation may cause a short circuit.
MP3 data
If the unit does not work properly, check the connections first （refer to the supplied “
JPG images
Installation/Connections” manual）. If everything in order, check the fuse.
Replacing the fuse
When replacing the fuse, be sure to use only a fuse of the same rating (ampere rating).
Using a different fuse or bridging the contacts with wire is highly dangerous and can lead to serious
The following types of discs/files are not compatible:
WMA files that are protected by DRM (Digital Rights Management)
WMA lossless format
Discs recorded with Track At Once or packet writing
MP3 PRO format
damage.
MP3 playlists
To prevent short circuits when replacing a fuse, disconnect the wiring harness first.
WAV format
Protect unit surface from damage
Do not expose the unit surface to chemicals such as insecticide, hair spray, insect repellent, etc.
Do not leave rubber or plastic materials in contact with the unit for along tine. Otherwise the finish of the
unit may be impaired, or deformation may occur.
When installing, be sure to turn the ignition key to the off position. Installing the unit while the ignition is on
may cause battery drain or short circuit.
WMV format
AVI format
Some recordable DVDs and CDs may be incompatible with this unit, depending on media type and
recording method.
I nstallation instructions
DVD Region Management
IMPORTANT INFORMATION
Some DVD discs can be played only in certain playback modes according to the intentions of the software.
Unit is designed for negative ground 12V DC systems only. The unit cannot be used in trucks or other cars
As the EXD 7090 plays discs according to their intentions, some functions may not work as intended.
with 24V systems.Otherwise, there is a risk of fire and damage.
Please be sure to read the instructions provided with each disc. This player has been designed to play
Do not disassemble or remodel the unit. This can cause electric shock, personal injury or fire. Do not
back DVD software that has been encoded for specific region areas. It cannot play back DVD software
connect any other system’s power supply cord directly. If you are in any doubt about the safe installation of
encoded for other region areas than the region areas for which it has been designed.
this unit, please consult your nearest EXONIC dealer.
The EXD 7090 will play discs labeled “Region 1” or “All”.
Do not install in locations which interfere with airbag operation. Otherwise there is a risk of accidents and
DVD region codes:
injury.
1 - USA, Canada 2 - Japan, Europe, South Africa, Middle East
Use only the specified fuse. When replacing the fuse, be sure to use only a fuse of the same rating
3 - Rep. of Korea, Taiwan, Hong Kong, Parts of Southeast Asia
(ampere rating). Otherwise there is a risk of fire.
4 - Australia, New Zealand, Mexico, South America
Do not ger the wires under a screw, or caught in moving parts (e.g.seat railing).
5 - Eastern Europe, Russia, India, Africa
Before making connections, turn the car ignition off to avoid short circuits.
6 – China
Connect the power input leads only after all other leads have been connected.
Copyrights
Be sure to insulate any loose unconnected wires with electrical tape for safety.
Run all ground wires to a common ground point.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
Parts supplied
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
The pack you have bought contains:
intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
EXONIC EXD 7090 Multimedia Disc Player
Corporation. Reverse engineering or disassembly is prohibited.
Power cord
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation
RCA connector
in the United States and or other countries.
Operation manual
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
Remote
All other trademarks are property of their respective owners.
IPod connector
Inport Adaptor
Making the electrical connections
Install all cables with care. For wiring, refer to the connection diagram.
To prevent the risk og accidents caused of short-circuits, connect the power supply leads, only after all
other wiring has been completed, and only with the ignition key in the OFF position. Otherwise, accidental
short-circuiting can lead to electric shock and to serious damage.
Subwoofer output
The SUBWOOFER audio output (Blue RCA) is active in all audio modes and must be connected to an
external amplifier.
Rear view camera
A rear view camera (not included) can be connected to the CAMERA input.
NEED HELP??
Contact nearest EXONIC dealer.
Expanded Wiring Diagram -Inputs/Outputs
REARVIEW CAMERA
Note:
Wiring Diagram - Optional A/V Connections
The remote control uses one 3 volt Lithium CR2025 battery. For best performance, replace only with
CR2025 or equivalent.
Installing the main unit
After all connections are made, install the main unit to the dashboard.
Before installation
This unit is designed to be completely safe, but if not installed correctly, it can cause accidents. Be sure to
verify the following points before installation.
Install the unit so that the monitor when opened up will not block access to the hazard switch or other
important controls.
Do not install the unit (monitor) in locations which maybe subject to excessively low or high temperatures.
(Otherwise the unit may be deformed and the LCD may be damaged.)
Exposure to direct sunlight can also lead to high temperatures and should be avoided.
Optional Backup
Camera
Selecting the installation location
1.Set the ignition key to OFF or remove it.
2.Place the units in their intended mounting locations to check the cable length and monitor installation
conditions.
Installation procedure precautions
Headrest Monitor
Perform the installation carefully. Dropping the unit or otherwise subjecting it to strong impact or force
may deform the chassis, resulting in failure of the monitor loading mechanism or other defects.
To allow for proper opening and closing of the monitor, there must be a clearance of at least 170 mm
between the closest position of the shift lever and the mounting surface for the unit.
In some cases, the shift lever may touch the monitor when moved to a certain position. Make sure that
there is no obstruction to driving operations.
The unit should be installed within an angle of 30 degrees from horizontal. If this angle is exceeded, the
monitor may not open up or retract properly.
Installation procedure
When installing this unit, be sure to close the monitor of the unit.
If the monitor is opened while installing and given too much force, it may cause a malfunction.
Front Amplifier
Remove the four #1 phillips head screws from each corner, and slide the unit out of the mounting sleeve.
Install mounting sleeve into opening, bending tabs to secure.
Connect wiring harness and antenna as shown on pages 9-10. Consult a qualified technician if you are
Sub Amplifier
unsure.
Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
Test for correct operation and slide unit into mounting sleeve, secure with #1 phillips screws as removed in
step 1.
Snap trim ring into place.
Rear Amplifier
Operation instructions
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
Detaching the front panel
You can detach the front panel of this unit.
1. Press
POWER
The unit is turned off.
2. Press
RELEASE
POWER
RELEAASE
Notes:Do not drop the front panel or put excessive pressure on them.
Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car
or on a dashboard/rear tray.
Resetting the unit
Before operating the unit for the first time, or after replacing the car battery or changing the connections,
you must reset the unit.
Detach the front panel by pressing RELEASE and pull it off towards you .
Use a pointed object such as a mechanical pencil to push the Reset button. To avoid the possibility of
damage, you should not use a needle or push the button too strongly.
Push Reset
Reset button
Notes:When the Reset button is pushed, the time and all stored settings are lost and will have to be
reprogrammed.
After installation and connections
1.Start the car’s engine.
2.Verify that the brake lights, other lights, horn, turn indicators, and all other electrical parts operate
normally.
3.Use a mechanical-pencil or similar to push the Reset button on the unit.
The reset procedure takes about 3 seconds after the Reset button is pushed.
When the reset procedure is completed, press OPEN/CLOSE an verify that the monitor oper, close
the monitor once. Otherwise, it may not operate properly.
Control elements
4. Disp
Press the DISP button to display CLOCK information on the secondary LCD screen when the monitor is
Main unit
Monitor closed
closed.
5. Open/Close Monitor
Press OPEN to open or close the monitor. The unit will emit 1 confirmation beep upon opening, 3 beeps
when closing. Be careful not to not touch or obstruct the monitor movement during the open/close
sequence, or permanent damage could occur.
17
Notes:The unit will stop automatically during open/close if an obstacle is detected. If this occurs,
remove the obstacle and press OPEN again to resume the monitor open/close sequence.
Audio can be heard while the monitor is closed.
6. Release
Press RELEASE, pull it off towards you, then the front panel is detached.
15
16
14
13
12
11
10
7. Rotary Encoder / Enter
Press to access MAIN menu, rotate clockwise/counter clockwise to select desired item and press once to
Monitor Notes:
ENTER.
This model incorporates a motorized moving monitor. Before final installation, make sure the monitor will
8. Microphone
not obstruct the dash, shifter or any other controls.
Microphone for the Bluetooth hands-free unit
Upon installation, do not attempt to move the monitor up/down by hand. Use the ANGLE ▲/▼and OPEN
9. IR
buttons on the front panel only.
Infrared receiver
10. SRC (Mode conversion)
The unit will stop if it encounters any obstacles during the open/close sequence. If this occurs, remove the
Press once to incrementally select desired source. Press MODE to select between TUNER, DVD, XM,
obstacle and press OPEN again to resume the monitor open/close sequence.
iPod, CAMERA and AV1 inputs. Modes of operation are indicated in the OSD (On Screen Display) and
secondary LCD.
1. Band
Note:
Press BAND to increment from FM1, FM2, FM3, AM10FM1.
iPod must be connected to appear in the MODE selection string.
2. AS/PS (Auto Store/Preset Scan)
11. Fast Forward
Press AS/PS for 1 second to start station PRESET SCAN function.
Fast forward the disc content.
Press AS/PS for 2 seconds to start AUTO STORE station preset function in current BAND.
12. Fast Reverse
3. Secondary LCD
Fast reverse the disc content.
Additional LCD for system information while monitor is closed
13. Stop
Stop playback of DVD / CD / MP3 / iPod.
14. Play/Pause
Press once for PAUSE, press again for PLAY.
15. Mute
1)LOC
Press once to MUTE audio, press again to return audio, an icon indicator will flash on the TFT monitor.
LOCAL indicator, icon will be off when DISTANT (DX) is selected
16. Power On/Off
2)ST
Press Volume knob for 1sec to turn the unit on, the unit will beep 2 times. Press and hold POWER for more
STEREO radio station indicator
than 2secs, unit will beep 3 time, then turn off. NOTE: EJECT will still function even if POWER is off.
3)TIME
Volume
Displays TRACK time, TUNING frequency, MP3 ID3 info, & CLOCK, etc
Rotate clockwise/counter clockwise for desired VOLUME level.
4)LOUD
17. Eject
LOUDNESS selection indicator
Press once for DISC ejection.
Monitor Open
After detaching the front panel
Reset button
Remote
10
Disc-In Indicator
Blue = No disc
Red = Disc inserted
Monitor Angle
Press ANGLE
to increase the monitor view angle.
Press ANGLE
to decrease the monitor view angle.
Notes:Do not attempt to move the monitor up/down by hand - severe damage will occur. Use the
front panel buttons or the remote control only.
The color of the LCD monitor varies between viewing angles. Select the angle with the most
optimum view for your location.
The last position of the monitor will be saved in memory. The monitor will return to its last position
automatically the next time it is opened.
4.Info/Pic
Press INFO button for 1 sec to display DVD disc information.
Press and hold INFO for 2 seconds to change TFT LCD BRIGHTNESS:
Press ANGLE to increase, ANGLE to decrease or use VOLUME rotary to adjust the brightness level up
or down (0 minimum / 20 maximum), 10 is default.
SD Card Slot
Main Access Menu
There are three methods to access the MAIN menu
Press the ENTER button on the right ROTARY knob.
Press the MENU button on the IR Remote control.
Touch the A area (upper left hand side) on the touch screen.
Touch Access Buttons
①Touch to access AM/FM TUNER mode.
②Touch to access CD/DVD mode, CD/DVD must be inserted.
③Touch to access SD card MODE, SD card must be inserted.
④Touch to access iPOD mode, iPod must be connected to activate.
⑤Touch to STANDBY screen, touch screen again or any button to resume display.
⑥Touch to access BLUETOOTH mode.
⑦Touch to access AUXILIARY A/V INPUT mode.
⑧Touch to access CAMERA mode, if optional camera isn't connected then "No Video Signal" will be
displayed.
Notes:
VOLUME level can be controlled without interrupting STANDBY.
Touch Screen
Hidden Touch Screen area while in TUNER mode
There are several hidden TOUCH SCREEN areas outlined below, "A" area can be used in any mode to
access MAIN menu
AREA FDVD Search
AREA C Selects PREVIOUS Track
DVD Transport Control OSD
Hidden Touch Screen area while in DVD mode
"A-F" areas can be used in DVD mode to access:
A - MAIN menu access
B - Displays DVD track information
C - Selects PREVIOUS chapter
D - Select NEXT chapter
E - Displays the full DVD transport controls
F - GOTO search menu
Touch Screen Controls
Using the Hidden Touch Screen Controls
Notes:
①Touch the
A DVD disc must be inserted to access these functions and features.
②Touch the
③Touch
④Touch the
PLAY button or on the front panel to resume disk playback.
PAUSE button again to suspend the disc playback.
button to STOP playback, touch
or OK on the remote to resume playback.
REVERSE button to FAST REVERSE on DVD, 2x, 4x, 8x to 20x.
⑤Touch the
FF button to FAST FORWARD on DVD, 2x, 4x, 8x to 20x.
⑥Touch the
Repeat to scroll through the following:
DVD: Repeat Title, Repeat Chapter, Repeat OFF
MP3: Repeat Single, Repeat Folder, Repeat OFF
A.Use the A-B function to define a specific area of disc to repeat. Press the Repeat A-B button to set a
start point of the (A) selection.
B.Press the A-B button again once you reach the desired end point (B) of the repeated section,
AREA A Access MAIN Menu
AREA D Selects NEXT Track
The selected portion of the DVD will now repeat continuously.
C.Press A-B button once again to cancel the A-B selection and stop repeat playback
⑦Touch to change Audio language playback
⑧Touch to change Sub-title of DVD
⑨Touch to return to DVD MAIN menu
Notes:Some DVD discs can be played only in certain playback modes according to the intentions of
the software. As the EXD 7090 plays discs according to their intentions, some functions may not
AREA B Displays DVD Track Information
AREA E Full DVD Transport Controls
work as intended. Please be sure to read the instructions provided with each disc.
Searching a DVD
13 AS/PS (AUTO STORE / PRESET SCAN)
Touch the search
button in AREA F.
14 BAND selection, FM1, FM2, FM3, AM
Searching by Time, Title or Chapter
15 VOLUME indicator
1 . Touch the in the TIME area.
2 . A touch keypad will now appear, enter your desired TIME to search.
16 LOUD indicator
3 . Enter OK.
17 Equalizer indicator, touch to access AUDIO Setup menu
18 Current radio frequency indicator
19 Current radio BAND indicator
Auto Seek Tuning
Press the
button to auto seeks up the next strongest station.
Press the
button to auto seeks down the next strongest station.
Manual Tuning
AM/FM Tuner Operation
Press the
button to manually tune up one step at a time.
AM/FM Tuner TFT Display
Press the
button to manually tune down one step at a time.
2 3
Auto Store (As)
Press and hold AS/PS for more than 2 seconds to automatically store the twelve strongest stations in the
current band. Automatic local tuning is activated during the initial band scan, repeat for other bands.
19
18
Notes:All presets within the current band will be overwritten.
Program Scan (PS)
17
16
Press AS/PS for less than 2 seconds to scan presets 1-12 on the current band, pausing for 5 seconds at
15
each. Press AS/PS again to cancel.
Scan
Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each station. Press
14
13 12
11
10
1 Current source MODE information, touch "A" area to return to MAIN source selection menu
2 Current PRESET station indicator
3 STEREO broadcast indicator
4 Clock
5 PRESET page up
6 LOCAL / DISTANCE selection
7 PRESET page down
8 Auto station SCAN button
9 MANUAL TUNE up
10 MANUAL TUNE down
11 SEEK TUNE up
12 SEEK TUNE down
SCAN again to cancel.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 13
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:4eab3213-98ef-45b4-b339-43579bb45c08
Mod Date--Text                  : ��
Creation Date--Text             : ��
Producer                        : Corel PDF Engine Version 1.0.0.458
Creator Tool                    : CorelDRAW 版本 12.0
Modify Date                     : 2008:05:07 17:07:40+08:00
Metadata Date                   : 2008:05:07 17:07:40+08:00
Document ID                     : uuid:79c1e2b0-67b0-438d-a44c-3d0b19d5cb4c
Format                          : application/pdf
Title                           : SD-9614-SV.cdr
Creator                         : JUJUMAO
Create Date                     : D:20080124142128
Author                          : JUJUMAO

EXIF Metadata provided by EXIF.tools