SKYRC Technology WIFIMODULE WiFi Module User Manual Addendum

SKYRC Technology Co., Ltd. WiFi Module Addendum

Addendum

Download: SKYRC Technology WIFIMODULE WiFi Module User Manual Addendum
Mirror Download [FCC.gov]SKYRC Technology WIFIMODULE WiFi Module User Manual Addendum
Document ID2302138
Application IDnPWy27axkzqRCmRONUgkAA==
Document DescriptionAddendum
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize3.85kB (48063 bits)
Date Submitted2014-06-20 00:00:00
Date Available2014-06-20 00:00:00
Creation Date2014-06-16 18:54:41
Producing SoftwareLibreOffice 3.5
Document Lastmod0000-00-00 00:00:00
Document TitleAddendum
Document CreatorWriter
Document Author: Adam

Federal Communication Commission Statement (FCC, U.S.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
IMPORTANT NOTES
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Co-location warning:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Limited Channels fixed for use in the US:
IEEE 802.11b or 802.11g or 802.11n(HT20) operation of this product in the U.S. is firmware-limited to
Channel 1 through 11, whereas IEEE 802.11n(HT40) operation limited to Channel 3 through 9.
Integrating this module in a host device / OEM integration instructions:
This device is intended only for OEM integrators under the following conditions:
1). The antenna must be installed such that 20 cm is maintained between the antenna and users, and the
transmitter module may not be co-located with any other transmitter or antenna. The module shall be only
used with the integrated on-board antenna as originally tested and certified with this module.
As long as these two integration instructions are met, further tests on this modular transmitter will not be
required. However, the OEM integrator is still responsible for testing the end-product for any additional
compliance requirements required with this module installed (for example, rule part 15B digital device
emissions, PC peripheral requirements, RF exposure requirements on host level when located with other
transmitters in the same device, etc.)
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location
with another transmitter), then the FCC authorization for this module in combination with the host equipment
is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a additional FCC authorization.
End product labeling:
This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users. The final end product must be labeled in a visible
area with the following: “Contains FCC ID: REY-WIFIMODULE”.
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user's manual of the end product which integrates this module. The end user
manual shall include all required regulatory information/warnings as show in this manual.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 1
Language                        : en-US
Author                          : Adam
Creator                         : Writer
Producer                        : LibreOffice 3.5
Create Date                     : 2014:06:16 18:54:41+02:00
EXIF Metadata provided by EXIF.tools
FCC ID Filing: REY-WIFIMODULE

Navigation menu