User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2139281 |
| Application ID | P2FzCKXG7lbArhU1FWvg+Q== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 95.67kB (1195907 bits) |
| Date Submitted | 2013-12-11 00:00:00 |
| Date Available | 2013-12-11 00:00:00 |
| Creation Date | 2013-10-31 11:49:39 |
| Producing Software | Acrobat Distiller 9.5.5 (Windows) |
| Document Lastmod | 2013-12-04 11:06:32 |
| Document Title | User_s Guide (Repeater)_ENG_ì¸ì¦ìš©.indd |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | in |
Supplies Per Models Repeater Installation Deck (Screw 2pcs) Repeater User's Guide SOLTREPEATER Adaptor Specification Model SOLTPEPEATER Frequency(MHz) 433.0500 ~ 434.7900 Freq Stability ±5 ppm Data Rate 1800 bps Channel space 12.5 KHz Modulation FSK (±3KHz) Output Power 10mW (Max) - Conducted Power Sensitivity -118dBm (at 12dB) Power Supply DC 12V/1A Adapter Dimension(mm) 146W × 90L x 32H Battery Life cycle External Power Antenna Tilt base snap-in_dipole (External) Repeater Repeater Name of each section Front ① Retractable antenna ① Folding antenna : 180 degrees pivot ② Bell number indicator : activated led number varies by different models. PWR Red led indicates power is on RX Blinking Red led indicates bell model TX Blinking Green led indicates pager model ③ Wall mount holes : Refer to item 4 of Installation Guide in page 53. ② Status indicator [Wall mount bracket installation] ③ Holes for wall mount MENU / ESC Back .&/6 &4$ ⶸ ⶼ ⶾ ⶺ 4&5 183 ·Menu button in setting mode · alphabetic and numeric changing button ▲ ▼ ·up /down ◀ ▶ ·left / right buttons SET / PWR /P3FDFJWF ④ Setting buttons ④ Setting buttons ·Storing button for set value ·Dower button ⑤ Display Missed call icon /P3FDFJWF ⑤ Call number Display ⑥ Adapter input: DC12V 1A (Use the supplied adapter) ⑥ Adapter input (DC 12V 1A) Limited accessary warranty: malfunctioning of supplied adapter during its use is not covered by manufactures' warranty. Purchasing an adapter with AC110~22OV input, DC12V 1A output is recommended. [Back cover] Input : AC110~220V Output : DC12V 1A Repeater Repeater Installation guide To assure the finest performance, please read this manual carefully. ② Bracket Installation ① Location ※ Transmitter must be installed with in 100% reception area. Install at roof like picture above, it is better if antenna direction go downward. In the case of cannot be installed to the roof install rear the roof. Once decided where to install, fix the mount. ③ Power Cord (Use the adapter provided in the package.) Transmitter (Main or Bell) Location. 100% Reception Area. It is most appropriate to install A location which is located within 100% reception area. (See map a picture above) ④ Wall Mounting (Pull down the unit until clicking sound is heard. ) ※ This product is needed to avoid moisture and water (It can be cause of breakdown) Recommend to install away from water. If needed to install outside of building, install where does net get wet. Repeater Repeater Repeater selection mode (Cbr / CPr) ·Sets the repeater as call bell repeater or pager repeater. Repeater setting modes ⑴ Press and hold (MENU) button for 3 seconds. Listed items below can be set by using user setting buttons. MENU ESC E1 Repeater selection mode Sets the repeater as call bell repeater or pager repeater. E2 Download mode Downloads registered call numbers from main transceiver. ▲ ▼ ◀ ▶ SET PWR ▶ SET PWR ·Entering setting mode as [E1 Rsel] is displayed. ⑵ Press (SET) button. [TBD] MENU ESC E3 No receive call number setting mode Selects call numbers that are not desired to receive. E4 Call redundancy interval setting mode Sets interval for redundant calls. (default value is 3 seconds) ▲ ▼ ◀ · [Cbr or CPr] is displayed. ⑶ Press (▲▼) buttons. (Cbr / CPr) E5 Call number deleting mode Deletes registered call numbers. E6 Call number registering mode Registers new call numbers. MENU ESC ▲ ▼ ◀ ▶ SET PWR Cbr : Extends bell receiving range by relaying bell's data to main transceiver. CPr : Extends pager receiving range by relaying main transceiver data to pager. ⑷ Press (SET) button. MENU ESC E7 ▲ ▼ ◀ ▶ SET PWR ·[E1 Rsel] is displayed and returns to previous step. TX delay time setting mode Sets delay time for received call number from bell. ※ Press (▲▼) buttons to select different setting mode. ⑸ Press (MENU) button. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·[ST-r5] is displayed and ready for reception. Repeater ·Selects call numbers that are not desired to receive. ·Downloads registered call numbers from main transceiver. ⑴ Press and hold (MENU) button for 3 seconds. ⑴ Press and hold (MENU) button for 3 seconds. MENU ESC MENU ESC ▲ ▼ ◀ ▶ SET PWR Repeater No receive call number setting mode Download mode ▲ ▼ ◀ SET PWR ▶ ·Entering setting mode as [E1 Rsel] is displayed. ·Entering setting mode as [E1 Rsel] is displayed. ⑵ Press (▲) button twice. ⑵ Press (▲) button once. MENU ESC ▲ ▼ ◀ [TBD] ▶ SET PWR MENU ESC ▲ ▼ ◀ SET PWR ▶ ·[E3 Daof] is displayed. ·[E2 Down] is displayed. ⑶ Press (SET) button. MENU ESC ▲ ▼ ◀ SET PWR ▶ ·Registered call number is displayed. ⑶ Press (SET) button. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·[---] is displayed. ⑷ Press (▲▼) buttons to select a Call number don't want to receive. MENU ESC ⑷ Press (SET) button. MENU ESC ▲ ▼ ◀ ▲ ▼ ◀ SET PWR ▶ ·Selected call number is displayed. ⑸ Press (SET) button to select desired receiving mode. ▶ SET PWR ·[---] is displayed during downloading is in progress. ·[E2 Down] is displayed when downloading is completed and returns to previous step. MENU ESC ▲ ▼ ◀ SET PWR ▶ ·[No Receive] button toggles each time SET button is pressed. ※ To set another receiving mode, repeat steps (4) to (5). ※ Press (▲▼) buttons to select different setting mode. ⑹ Press (MENU) button. ⑸ Press (MENU) button. MENU ESC MENU ESC ▲ ▼ ◀ ▶ SET PWR ▲ ▼ ▶ SET PWR ·[ST-r5] is displayed and ready for reception. ·[ST-r5] is displayed and ready for reception. /P3FDFJWF 10 ◀ e.g.) Call number 200 is set to not receive when [No Receive] icon is displayed. 11 Repeater ·Deletes registered call numbers. ·Sets interval for redundant calls. ⑴ Press and hold (MENU) button for 3 seconds. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Entering setting mode as [E1 Rsel] is displayed. ▲ ▼ ◀ ▶ SET PWR ·[E4 Dupt] is displayed. ▲ ▼ ◀ MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Entering setting mode as [E1 Rsel] is displayed. MENU ESC ▲ ▼ ◀ ▶ SET PWR ▶ SET PWR ·[E5 Dele] is displayed. ⑶ Press (SET) button. ⑶ Press (SET) button. MENU ESC ⑴ Press and hold (MENU) button for 3 seconds. ⑵ Press (▲) button 4 times. ⑵ Press (▲) button 3 times. MENU ESC Repeater Call number deleting mode Repetition call setting mode ▶ SET PWR ·[3] is displayed. MENU ESC ▲ ▼ ◀ ·Registered call number is displayed. ※ 3 is set for default. (Unit : second) ⑷ Press (▲▼) buttons. Sets the desired number. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Selected number is displayed. ⑸ Press (SET) button. MENU ESC ▲ ▼ ◀ ⑷ Press (▲▼) button. Select the call number you want to delete. MENU ESC ▲ ▼ ◀ ▶ SET PWR ▶ SET PWR ·Selected call number is displayed. ⑸ Press (SET) button. ▶ SET PWR ·[E1 Rsel] is displayed and returns to previous step. MENU ESC ▲ ▼ ◀ ·" It has been deleted." is played. ·To delete another call number, repeat the processes from (4) to (5). ※ Press (▲▼) buttons to select different setting mode. ⑹ Press (MENU) button. ⑹ Press (MENU) button. MENU ESC 12 ▲ ▼ ◀ ▶ SET PWR ·[ST-r5] is displayed and ready for reception. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·[ST-r5] is displayed and ready for reception. 13 Repeater Repeater Call number registering mode ·Registers new call numbers. ⑴ Press and hold (MENU) button for 3 seconds. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Entering setting mode as [E1 Rsel] is displayed. ⑵ Press (▲) button 5 times. MENU ESC ▲ ▼ ◀ ▶ SET PWR ⑸ Press (SET) button. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Selected-number from (4)section is displayed on the screen and the number stop blinking. ⑹ Press the button to register. ·[E6 Breg] is displayed. ·Registration for selected call number is completed. ·The number of screen is again blinking. 䌫䌬䌅䌚䌍 ⑶ Press (SET) button. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Blinking [0] is displayed. ·To register another Bell, repeat the processes from (4) to (6). ⑷ Press (▲▼◀▶) buttons. sets desired to call number. MENU ESC ▲ ▼ ◀ ▶ SET PWR · Press (◀▶) buttons to move to different digits. · Press (MENU) button to toggle input mode from / to numeric and English modes. ⑺ Press and hold (SET) button for 3 seconds when registration is finished. MENU ESC Number mode ▲ ▼ ◀ ▶ SET PWR ·[ST-r5] is displayed and ready for reception. %ODQN English mode %ODQN 14 15 Repeater TX delay time setting mode ·Sets delay time for received call number from bell. ⑴ Press and hold (MENU) button for 3 seconds. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Entering setting mode as [E1 Rsel] is displayed. ⑵ Press (▲) button 6 times. MENU ESC ▲ ▼ ◀ ▶ SET PWR ▶ SET PWR ·[E7 Txdt] is displayed. ⑶ Press (SET) button. MENU ESC ▲ ▼ ◀ ·[0] is displayed. ·10(1Second), 20(2Second) ... 100(10Second) ※ '0' is default value : transmits as soon as receiving a call. ⑷ Press (▲▼) buttons. Sets the desired number. MENU ESC ▲ ▼ ◀ ▶ SET PWR ·Selected number is displayed. ⑸ Press (SET) button. MENU ESC ▲ ▼ ◀ ▶ SET PWR · [E1 Rsel] is displayed and returns to previous step. ※ Press (▲▼) buttons to select different setting mode. ⑹ Press (MENU) button. MENU ESC 16 ▲ ▼ ◀ ▶ SET PWR ·[ST-r5] is displayed and ready for reception. FCC compliance Information When used the This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. and (2) This device must accept any interference received, including interference that may cause undesired operation. Cautions Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-702 Format : application/pdf Title : User_s Guide (Repeater)_ENG_인증용.indd Creator : in Create Date : 2013:10:31 11:49:39+09:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2013:12:04 11:06:32+09:00 Metadata Date : 2013:12:04 11:06:32+09:00 Producer : Acrobat Distiller 9.5.5 (Windows) Document ID : uuid:6c0c538d-b91a-4816-b92e-95d8d0b5ad0b Instance ID : uuid:5ea12c0a-1e11-4f40-9049-b6d38c0603dc Has XFA : No Page Count : 8 Author : inEXIF Metadata provided by EXIF.tools