SOYO SY 7IWB QSG 7iwb10 User Manual To The 4d3e6533 4489 4716 9e6d 90f29b1280d6

User Manual: SOYO SY-7IWB to the manual

Open the PDF directly: View PDF .
Page Count: 22

SY-7IWB

Motherboard

Quick Start Guide

Hardware

Installation

Quick BIOS

Setup

Introduction

The SOYO CD

Crystal Audio

Driver

Installation

SOYO™

SY-7IWB Motherboard

Socket 370 for Intel Celeron

processors

Intel FW82810 AGP/PCI/AMR Motherboard

100 & 66 MHz Front Side Bus supported

Baby AT Form Factor

Trademarks:

Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of

their owners.

Product Rights:

All names of the product and corporate mentioned in this publication are used for identification

purposes only. The registered trademarks and copyrights belong to their respective companies.

manual may be reproduced, transmitted, transcribed, translated into any other language, or

stored in a retrieval system, in any form or by any means, such as by electronic, mechanical,

magnetic, optical, chemical, manual or otherwise, without permission in writing from Soyo

Computer Inc.

Disclaimer:

Soyo Computer Inc. makes no representations or warranties regarding the contents of this

manual. We reserve the right to amend the manual or revise the specifications of the product

described in it from time to time without obligation to notify any person of such revision or

amend. The information contained in this manual is provided to our customers for general use.

Customers should be aware that the personal computer field is subject to many patents. All of

our customers should ensure that their use of our products does not infringe upon any patents. It

is the policy of Soyo Computer Inc. to respect the valid patent rights of third parties and not to

infringe upon or to cause others to infringe upon such rights.

Restricted Rights Legend:

Use, duplication, or disclosure by the Government is subject to restrictions set forth in

subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at

252.277-7013.

About This Guide:

This Quick Start Guide can help system manufacturers and end users in setting up and installing

the Motherboard. Information in this guide has been carefully checked for reliability; however,

to the correctness of the contents there is no guarantee given. The information in this document

is subject to amend without notice.

For further information, please visit our Web Site on the Internet. The address is

"http://www.soyo.com.tw".

7IWB Serial - Version 1.0 - Edition: July 1999

* These specifications are subject to amend without notice

SY-7IWB

Quick Start Guide

Introduction

Congratulate on your purchase of the

SY-7IWB

Motherboard. This Quick Start Guide

illustrates the steps for installing and setting up your new Motherboard.

This guide provides all users with the basic steps of Motherboard setting and operation. For

further information, please refer to SY-7IWB Motherboard Uses’ Guide and Technical

Reference online manual enclosed in the CD-ROM package with your Motherboard.

Unpacking

When unpacking the Motherboard, check for the following items:

The SY-7IWB

FW82810

AGP/PCI/AMR

Motherboard

This Quick Start Guide

The Installation CD-

ROM

SOYO 3-in-1 Bonus

Pack CD-ROM (Norton

AntiVirus, Ghost and

Virtual Drive)

One IDE Device Flat

Cable

One Floppy Disk Drive

Flat Cable

One dual 25-pin parallel

with 25-pin flat cable

and 9-pin serial with 9-

pin flat cable external

connector

One dual 6-pin PS/2

mouse connector with

6-pin flat cable and 9-

pin serial connector with

9-pin flat cable

VGA port flat cable with a

15-pin connector bracket

One game port and

Audio connector

bracket with flat cables

LINE-IN

MIC

LINE-OUT

SY-7IWB Quick Start Guide

Introduction

SY-7IWB Motherboard Layout

AT Power

Lithium

Battery

Intel

FW82810

PCI Slot #2

PCI Slot #1

PCI Slot #3

USB1

Socket 370

DIMM 2

DIMM 1

DIMM 3

Intel

FW82801AB

Ac97

Codec

Speaker

Keylock

Power

LED

ACPI

LED

HDD

LED _

Reset

PWRBT

JP5

1 3 JP2

1 3

CMOS Clear

Jumper

JP10

FDC

IDE 1

IDE 2

J10

J11

JP44

WOL

Header

PRT 1

Connector

PS/2 Mouse

Connector

ATX Power

COM 2

COM 1

CPU FAN

JP1

JP15

1 3

Intel

82802AB

4MB

AMR1

IR1

Winbond

W83627HF

-AW

Audiuo Port

GAME Port

VGA Port

JP9

AU8810

SY-7IWB

Quick Start Guide

Introduction

Key Features

Supports Intel Celeron™ processors

(300A-500MHz)

Supports 100 & 66 MHz Front Side Bus

Frequency

Auto detect CPU bus Frequency (66/100)

Auto-detect CPU voltage

Adjustable CPU Core Voltage (Normal,

5%)

Chipset integrated 3D AGP Accelerator

Easy CPU settings in BIOS with the

“SOYO COMBO Setup”

Software Audio AC97 Version 2.1

Compliant

PC98, ACPI, Ultra DMA33

Supports Wake-On-LAN (WOL) when

use ATX-Power supply

Supports ACPI Suspend Indicator

Power-on by modem, alarm, PS/2

Keyboard, Mouse and USB Win98

Keyboard

Power failure resume

Supports onboard hardware monitoring

and includes Hardware Doctor™ utility

Fan speed control

Battery Low voltage Detect

Support 7 sets of voltage monitoring

Supports multiple-boot function

Y2K Compliant

Supports Audio Modem Riser slot (AMR

1.0 compliant) *

3 x 32-bit bus mastering PCI slots

2 x USB ports onboard

1 x IrDA port

AT power connector

ATX power connector

Hardware Random Number Generator

(RNG) for enabling enhanced platform

security

RTC hardware to handle Y2K Century

Rollover

* If the user wants to use a Modem Riser card (MR) make sure to use a

Secondary

mode MR,

PRIMARY

mode MRs are

NOT

Supported.

SY-7IWB Quick Start Guide

Hardware

Installation

To avoid damage to your Motherboard, please follow these simple rules while

handling this equipment:

Before handling the Motherboard, ground yourself by holding on to an unpainted

portion of the system's metal chassis.

Remove the Motherboard from its anti-static packaging. Hold the motherboard by the

edges and avoid touching its components.

Check the Motherboard for damage. If any chip appears to be loosened, press

carefully to seat it firmly in its socket.

Follow the directions in this section which is designed to guide you through a quick and

correct method to install your new

SY-7IWB

Motherboard. For detailed information, please

refer to SY-7IWB Motherboard User's guide and Technical Reference online manual

enclosed in the CD-ROM package with your Motherboard.

Gather and prepare all necessary hardware equipment to complete the installation

successfully:

Celeron

processor with built-in CPU cooling fan (boxed type)

SDRAM module

Computer case and chassis with adequate power supply unit

Monitor

Keyboard

Pointing Device (Mouse)

Speaker(s) (optional)

Disk Drives: HDD, CD-ROM, Floppy drive…

External Peripherals: Printer, Plotter(optional)

Internal Peripherals: MR and LAN cards (optional)

Note: 1.

This Motherboard features one built-in VGA port and three built-in audio-stereo

ports. Therefor you do not need to install neither a VGA card nor a sound card.

If you want to use an external speaker connected to "Line-out" port, please make

sure to use an "amplified speaker" that can generate proper output sound volume.

SY-7IWB

Quick Start Guide

Hardware

Installation

Install the Motherboard

To perform the installation of your new

SY-7IWB

Motherboard, follow the steps below

Step 1. CPU Installation

Mark your CPU Frequency:

Record the working frequency of your CPU

that should be clearly marked on the CPU cover.

300MHz (66 x 4.5) 333MHz (66 x 5.0) 366MHz (66 x 5.5) 400MHz (66 x 6.0)

433MHz (66 x 6.5) 466MHz (66 x7..0) 500MHz (66 x7.5)

This Motherboard is designed to support processors with 100MHz FSB. However, Socket

370 processors with 100MHz FSB are not available at present.

CPU Mount Procedure:

To mount the Celeron

processor that you have

purchased separately, follow these instructions.

Lift the socket handle up to a vertical position.

Align the blunt edge of the CPU with the matching pinhole distinctive edge on the

socket.

Seat the processor in the socket completely and without forcing.

Then close the socket handle to secure the CPU in place.

Remember to connect the CPU Cooling Fan to the appropriate power

connector on the Motherboard. The fan is a key component that stabilize the

system. It prevents the equipment from overheating and prolongs the life of

your CPU.

3 4

cket 3

SY-7IWB Quick Start Guide

Hardware

Installation

Step 2. Connections to the Motherboard

This section tells how to connect internal peripherals and the power supply to the

Motherboard.

Internal peripheral is composed of IDE devices (HDD, CD-ROM), Floppy Disk Drive,

Chassis Fan, Front Panel Devices (ACPI LED, Internal Speaker, Reset Button, IDE LED,

and KeyLock Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.

For more details on connecting internal and external peripherals to your new SY-7IWB

Motherboard, please refer to SY-7IWB Motherboard User's Guide and Technical Reference

online manual on CD-ROM.

Connectors and Plug-ins

Wake-On-LAN Header: JP44 CPU Cooling Fan: CPUFAN Chassis Fan: CHAFAN

Pin1 Pin2 Pin3 Pin1 Pin2 Pin3 Pin1 Pin2 Pin3

5VSB GND MP-Wakeup GND 12V SENSOR GND 12V SENSOR

IrDA (Infrared Device Header): IR1 Game Port Connector : J5

Pin1 Pin2 Pin3 Pin4 Pin5

VCC None IRRX GND IRTX Connect the game port flat cable from the

game port/ Audio bracket to J5.

CD Line-in: J10,J11 Pin1 Pin2 Pin3 Pin4

J10 RGLG

Connect the CD Line-in cord from the CR-ROM

device to the matching connector CDIN J11

RG G L

Power LED Keylock

Pin1 Pin2 Pin3

Pin1 Pin2

5V NC GND

Control Pin GND

Speaker

Pin1 Pin2 Pin3 Pin4

5V NC NC Speaker out

HDD LED ACPI LED PWRBT RESET

Pin1 Pin2 Pin1 Pin2 Pin1 Pin2 Pin1 Pin2

LED Anode LED Cathode LED Anode LED Cathode Power On/Off GND Power Good GND

AT Power Cable ATX Power On/Off: PWRBT

Connect the AT Power cable

to this connector.

Connect your power switch to this header (momentary switch type).

To turn off the system, press this switch and hold down for longer than

4 seconds.

ATX Power Supply: ATX PW

Attach the ATX Power cable to this connector.

When using the Power-On by PS/2 Keyboard function, please make sure the ATX power supply is able to be

loaded at least 720mA on the 5V Standby lead (5VSB) in order to meet the standard ATX specifications.

Note: Use only ONE type of power supply. If an AT power supply is used, do not attach an ATX power

supply.

Power LED

Key Lock

Speaker

Reset

PWRBT

ACPI LED

HDD LED

SY-7IWB

Quick Start Guide

Hardware

Installation

Step 3. Configure Memory

Your board comes with three DIMM sockets, and provides support up to 512MB main

memory using PC100 DIMM modules from 8MB to 256MB.

Memory Configuration Table

Number of

Memory Modules DIMM 1 DIMM 2 DIMM 3

1Double-sided/

Single-sided Double-sided/

Single-sided

2Double-sided/

Single-sided Single-sided Single-sided²

RAM Type SDRAM¹

Memory Module Size (MB) 8/16/32/64/256 Mbytes

Note: 1. PC100 Compliant DIMM module is required regardless of 66 or 100

MHz FSB speed.

2. If you want to use DIMM3, DIMM2 must be used as well to let the

system work properly. Just plugging a memory module into DIMM3

with DIMM2 left empty, will make the system not working.

Step 4. Set J6 &JP2 to configure CPU FSB Frequency

If the user wants to use the CPU at its standard FSB (Front Side Bus) Frequency, J6 has to

be closed. This will make sure the system will provide the CPU with the FSB Frequency it

was specified to run at. Make sure that JP2 is open when using this setting.

If the user wants to run the CPU at another (higher) FSB frequency however, J6 has to be

open. In this case use JP2 to set the FSB frequency.

Auto Mode Description

J6 JP2

Short J6

Must

open

Run the CPU at its specified FSB frequency.

For 66MHz FSB CPUs 66/75/83 MHz can be

selected in the BIOS.

For 100MHz FSB CPUs 100~133MHz can be

selected in the BIOS.

Note

: Don’t put any jumper on JP2 when J6 is set to short.

SY-7IWB Quick Start Guide

Hardware

Installation

Manual Mode

Description

J6 JP2

Open J6 Short pin

1-2

Set power up FSB frequency to 66MHz if the user

wants to run the CPU at a FSB frequency of

66MHz. Only 66~83MHz FSB can be set in the

BIOS.

J6 JP2

Open J6 Short pin

2-3

Set Power up FSB frequency to 100MHz if the user

wants to run the CPU at an FSB frequency of

100MHz or higher. This setting will allow the user to

run the CPU at a higher FSB frequency, especially

when the user wants to urn a 66MHz FSB CPU at

100MHz and higher FSB frequencies.

Note

: The “Manual” mode setting facilitates FSB over-clocking. Doing so will however force

your CPU to operate out of its specifications, and therefore SOYO can not guarantee the

proper function of your system.

Step 5. Set the CPU Frequency

This Motherboard does not use any jumpers to set the CPU operating frequency; theCPU

settings can be changed through the BIOS [SOYO COMBO SETUP]. Please refer to

Chapter 3 “Quick BIOS Setup” for details on setting the

Celeron

processor frequency.

Step 6. Set for JP9 FWH Boot Block Write-Protect

Setting this jumper to open will prevent the boot block area of the FWH (FirmWare Hub) chip

from being written data into such that it is write-protected from unwanted or abnormal write

activity.

Note

: In some rare cases, the boot block area will need to be flashed to complete the BIOS

upgrade procedure. Setting JP9 to open will cause incomplete BIOS update in that case.

The FWH Boot Block

Write-Protect Locked Unlocked

JP9 Setting open JP9 short JP9

SY-7IWB

Quick Start Guide

Hardware

Installation

Step 7. Enable/Disable Power-On by Keyboard (JP1)

You may choose to enable the Power-On through Keyboard function by shorting pin 1-2 on

jumper JP1; or short pin 2-3 to disable this function.

Power-On by

Keyboard Enable Disable

JP1 Setting

Short pin 1-2 to

enable the Power-

On by Keyboard

function.

Short pin 2-3 and

the Power-On by

Keyboard function is

disabled.

Important: When using the Power-On by Keyboard function, please make sure the

ATX power supply is able to provide at least 720mA on the 5V Standby lead (5VSB)

in order to meet the standard ATX specification.

Step 8. PC speaker redirection (JP10)

Through this jumper the case speaker output can be redirected to the external (amplified)

speakers (if connected) through the on-board Audio-Codec.

PC speaker

redirection Redirect to external speaker Use case speaker

JP10 Setting Short pin 1-2 Short pin 2-3

Step 9. CPU Core Voltage Adjust (JP15)

In case your CPU is running on a frequency higher then it is specified for, increasing its core

voltage can enhance its stability. Over-clocking your CPU does however force your system

to operate outside of its specifications, and therefore SOYO can not guarantee system

stability.

CPU Core Voltage

Adjust JP15 Setting

Default Vcore

short pin 1-2

5% higher

short pin 2-3

SY-7IWB Quick Start Guide

Hardware

Installation

Step 10. CMOS Clear (JP5)

After you have turned off your computer, clear the CMOS memory by momentarily shorting

pins 2-3 on jumper JP5, for a few seconds. Then restore JP5 to the initial 1-2 jumper setting

in order to recover and retain the default settings.

Jumper JP5 can be easily identified by its white colored cap.

CMOS Clearing Clear CMOS Data Retain CMOS Data

JP5 Setting Short pin 2-3 for

at least 5 seconds to

clear the CMOS

Short pin 1-2 to

retain new settings

Note: You must unplug the ATX power cable from the ATX power connector when

performing the CMOS Clear operation.

Note on Over-clocking Capability

The SY-7IWB provides over-clocking capability. Due to the over-clocking setting your system

may fail to boot up or hang during run time. Please perform the following steps to recover

your system from the abnormal situation :

Turn off system power (If you use an ATX power supply, and depending on your system,

you may have to press the power button for more than 4 seconds to shut down the

system.)

Set the J6 to open and set the JP2 pin 1-2 if you use a FSB 66MHz CPU.

Press and hold down the <Insert> key while turning on the system power. Keep holding

down the <Insert> key until you see the message of the CPU type and frequency shown

on the screen.

Press the <Del> key during the system diagnostic checks to enter the Award BIOS Setup

program.

Select [Soyo Combo Feature] and move the cursor to the [CPU Frequency] field to set the

proper working frequency.

Select [Save & Exit SETUP] and press <Enter> to save the new configuration to the

CMOS memory, and continue the boot sequence.

Note: SOYO does not guarantee system stability if the user over clocks the system.

Any malfunctions due to over-clocking are not covered by the warranty.

SY-7IWB

Quick Start Guide

Quick BIOS

Setup

Quick BIOS Setup

This Motherboard does not require any hardware jumpers to set the CPU operating

frequency. Instead, CPU settings are software configurable with the BIOS

[Soyo Combo

Feature].

The [Soyo Combo Feature] menu combines the main parameters that you need

to configure. They are all in one menu to enable a quick setup in BIOS.

After completion of hardware installation, turn the power switch on, then press the

<DEL>

key

while the system diagnostic is checking to enter the Award BIOS Setup program. The CMOS

SETUP UTILITY will display on screen. Then follow these steps to configure the CPU settings.

Step 1. Select [Standard CMOS Features]

Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.

Step 2. Select [Load Optimized Defaults]

Select the “Load Optimized Defaults” menu and type “Y” at the prompt to load the BIOS

optimal setup.

Step 3. Select [Soyo Combo Feature]

Move the cursor to the

[CPU Frequency]

field to set the CPU frequency.

The following table shows all available [CPU Frequency] settings on your SY-7IWB

Motherboard . If you set this field to [Manual], then you will be required to fill in the next two

consecutive fields: (1) the CPU Host/PCI Clock, and (2) the CPU Ratio.

CPU Frequency

300MHz (66 x 4.5)

333MHz (66 x 5.0)

366MHz (66 x 5.5)

400MHz (66 x 6.0)

433MHz (66 x 6.5)

466MHz (66 x 7.0)

500MHz (66 x 7.5)

Select the working frequency of your Celeron TM

processor among these preset values.

Note: Mark the checkbox that corresponds to

the working frequency of your Celeron TM processor

if the CMOS configuration is lost.

Note:

if you use Bus Frequencies of 75 MHz, make sure that your PCI cards are compatible

with the higher PCI clock.

Step 4. Select [SAVE & EXIT SETUP]

Press

<Enter>

to save the new configuration to the CMOS memory, and continue with the

boot sequence.

SY-7IWB

Quick Start Guide

The SOYO CD

The SOYO-CD will NOT autorun if you use it on an Operating System other

than Windows 9x or NT.

Your SY-7IWB Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD

contains (1) the user's manual file for your new Motherboard, (2) the drivers software

available for installation, and (3) a database in HTML format with information on SOYO

Motherboards and other products.

Step 1. Insert the SOYO CD into the CD-ROM drive

The SOYO CD will auto-run, and the SOYO CD Start Up Menu will be shown as below.

(SOYO CD Start Up Program Menu)

If you use Windows 95/98, the SOYO CD Start Up Program automatically detects which

SOYO Motherboard you own and displays the corresponding model name.

Step 2. Read SOYO [7IWB] Manual

Click the

Read Manual

button to open the user's manual file of your Motherboard.

SY-7IWB

Quick Start Guide

The SOYO CD

Please note that if the Start Up program was unable to determine which SOYO

Motherboard you own, the manual selection menu will pop up, as shown below. Then

select the user's manual file that corresponds to your Motherboard model name and click

OK.

(Manual Selection Menu)

The user's manual files included on the SOYO CD can be read in PDF (Postscript

Document) format. In order to read a PDF file, the appropriate Acrobat Reader software

must be installed in your system.

Note:

The Start Up program automatically detects if the Acrobat Reader utility is already

present in your system, and otherwise prompts you on whether or not you want to install it.

You must install the Acrobat Reader utility to be able to read the user's manual file. Follow

the instructions on your screen during installation, then once the installation is completed,

restart your system and re-run the SOYO CD.

Step 3. Install Drivers

Click the

Install Drivers

button to display the list of drivers software that can be installed

with your Motherboard. The Start Up program displays the drivers available for the

particular model of Motherboard you own. We recommend that you only install those

drivers. If you use Windows NT, only select the drivers listed here.

However, to display the list of all drivers software available with SOYO Motherboards, click

the

Display all drivers on the SOYO CD

button. Please make sure to install only the

drivers adapted to your system, or otherwise this may cause system malfunctions.

SOYO CD Manuals

Please select your manual in the box below

and click OK.

686 boards:586 boards:

OKBack

7IWB

SY-7IWB

Quick Start Guide

The SOYO CD

(Driver Installation Menu)

A short description of all available drivers follows:

Ø INTEL Whitney VGA Drivers for Win 9x

In order to be able to make use of the integrated VGA function in your Whitney

chipset, you will need to install this driver first. For Windows 95/98 only.

Ø INTEL Whitney .inf utility for Win 9x

Windows 95 and 98 will not recognize the new INTEL Whitney chipset properly. To

update the necessary .inf files that will help Windows recognize the Whitney chipset,

please run this utility.

Ø INTEL Whitney security utility for Win 9x/NT

This utility makes use of the random number generator in the FWH of your 810/820

chipset. for Win 95/98/NT.

Ø 7IWB Winbond hardware Doctor for Win 95/98

Your motherboard comes with a hardware monitoring IC. By installing this utility

Temperature, Fan speed and Voltages can be monitored. It is also possible to set alarms

when current system values exceed or fall below pre-set values.

Select which driver you want to install and click

OK,

or click

Cancel

to abort the driver

installation and return to the main menu.

Please select the driver you want to install and click OK, You will have to

restart your system after installation. Only the drivers that are relevant

to your board are displayed initially.

Intel Whitney VGA Drivers for Win 9x

Intel .inf utility for Win 9x

Intel Whitney security utility for Win 9x/NT

7IWB Winbond hardware Doctor for Win 95/98

CancelDisplay all drivers

on the SOYO CDOK

Driver Installation

SY-7IWB

Quick Start Guide

The SOYO CD

Note:

Once you have selected a driver, the system will automatically exit the SOYO CD to

begin the driver installation program. When the installation is complete, most drivers

require to restart your system before they can become active.

Step 4. Check the Latest Releases

Click the 'Check the latest Releases' button to go the SOYO Website to automatically find

the latest BIOS, manual and driver releases for your motherboard. This button will only

work if your computer is connected to the internet through a network or modem

connection. Make sure to get your modem connection up before clicking this button.

Step 5. Enter the SOYO CD

Click the

Enter SOYO CD

button to enter the SOYO HTML database. The Start Up

program will activate the default HTML browser installed on your system (for example,

Internet Explorer or Netscape) to display the contents of the SOYO CD.

The SOYO CD contains useful information about your Motherboard and other SOYO

products available. For your convenience, this information is available in HTML format,

similar to the format widely used on the Internet.

Note:

If no HTML browser is installed on your system, the Start Up program will prompt

you on whether or not you would like to install the Internet Explorer* browser. Click YES to

install the HTML browser. After the installation is complete, please restart your system.

Then re-run the SOYO CD and you will be able to browse the SOYO HTML database.

(* Internet Explorer is a Microsoft Trademark)

SY-7IWB

Quick Start Guide

Crystal Audio

Driver

Installation

Crystal Audio Driver Installation

Installing Crystal Audio Drivers under windows 9x

1. Open Device Manager.

2. PCI Multimedia Device will have a yellow marker the first time the operating system is installed.

3. Select "Properties" on the yellow marker.

4. Select the "Driver" tab.

5. Click on "Update Driver"

6. Select the following directory:

D:\driv-all\crystal\window9x\image

and click OK. You will need the Windows Second Edition to complete the WDM installation.

7. The entry that will show up in the Sound, Video, and Game Controllers is: Crystal WDM Audio

Codec.

8. A little Sound Icon appears on the Task Bar upon completing the driver installation.

Uninstalling/Re-Installing Crystal Audio Drivers

1. Open Device Manager.

2. Remove Crystal WDM Audio Codec entry in the Sound, Video, and GameControllers section.

Crystal is not the owner of the game controller on this audio solution.

3. Delete Crystal INF in c:\windows\inf\other

4. Restart your PC for Plug and Play to reinitialize your system.

Known Limitations

1. Clicking the Stop button causes loud pops while playing Midi through Media Player, when

Headphone control is used.

2. Playing any wave using the Dsound application causes a loud pop when the Play button is clicked.

3. After Remove/Refresh, no software wavetable audio is available after a reboot.

4. The Play and Stop button cause loud pops while playing wave through the Media player.

5. There may be some feed back noise when Microphone boost is enabled.

6. A reboot may be required to play MIDI audio after the initial installation of the driver.

7. Panning Headphone and Wave balance in the Output mixer while playing a aWave/CD/Line-in

signal causes a pop.

SY-7IWB

Quick Start Guide

Crystal Audio

Driver

Installation

Special Design Considerations

1. The Headphone does not mute the audio when the headphone slider is adjusted to the minimum

value.

2. SW Synth slider jumps to max value, when Synth state is switched from Stop to Play or viceversa.

3. Master Volume levels are quite low when compared to Headphone volume levels.

4. Fastforward and Rewind Controls in the Media Player can not enabled.

5. When resuming from sw wavetable playback, midi is paused.

6. Digital CD Audio is recorded by loopback mux selection.

7. Mono Mix volume is low.

8. Some Dos games do not run in a Dos Box. This support is provided by the Microsoft legacy Audio

emulator.

Note: The above limitations list is as provided by the codec manufacturer, SOYO will provide customers

with new driver releases through the SOYO website as soon as they are released by the manufacturer.

Installing Crystal Audio Drivers for Windows NT

1. Double click the MULTIMEDIA icon in the control panel. The Multimedia Properties windows will

appear. Click on the Devices tab and press the Add button.

2. Select "Unlisted or Updated Drivers" from the list of drivers in the Add window by placing the mouse

pointer over it and clicking the left mouse button. Press the OK button.

3. The Install Driver dialog box will appear and request the path of the location of the drivers to be

installed. Enter D:\driv-all\crystal\NT (where D: is your CDROM drive) If the installation fails, first copy

all the files in the above directory to your harddisk and give that directory to NT.

4. The label "SoundFusion(tm)" is displayed on the dialog box. Press OK to continue with the

installation.

5. Windows NT will display a dialog box asking you to restart your system.

Press the Restart Now button to complete the installation.

Uninstalling or Updating Crystal Audio Drivers

1. Double click on the MULTIMEDIA icon in the control panel. Select the Devices tab from the

Multimedia properties window.

2. Double click on the Audio Devices entry from the Multimedia devices list. Select the driver by placing

the mouse pointer over the label "Audio for SoundFusion(tm)" and clicking the left mouse button.

3. Press the REMOVE button.

4. A question box will appear to verify your decision. Press the YES button.

5. WindowsNT will dislplay a dialog box asking you to restart your system. Press the Restart Now

button to complete the Un-installation.

SY-7IWB

Quick Start Guide

How to contact us:

n If you are interested in our products, please contact the SOYO sales

department in the region you live.

n If you require Technical Assistance, please contact our Technical Support in

the region you live.

SOYO prefers Email as communication medium, remember to always add to the

email the country that you live in.

SOYO Taiwan

No. 21 Wu-Kung 5 Rd., Hsin Chuang

City, Taipei Hsien, Taiwan

Region Covered: Taiwan and Asia-

Pacific. (Including Australia).

Web Site: www.soyo.com.tw

Sales:

Tel: 886-2-22903300-318

Fax: 886-2-22983322

E-mail: salesap@mail.soyo.com.tw

Technical Support:

Fax: 886-2-22983322

E-mail: support@mail.soyo.com.tw

SOYO Europe BV

Signaalrood 19, 2718 SH Zoetermeer

The Netherlands

Region Covered: Europe except

Germany, Austria and Switserland

Web Site: www.soyo.nl, www.soyo-

europe.com

Sales:

Tel: +31-69-3637500

Fax: +31-79-3637575

Email: sales@soyo.nl

Technical Support:

Tel : +31-79-3637500

Fax: +31-79-3637575

Email: support@soyo.nl

SOYO USA

41484 Christy Street, Fremont, CA

94538

Region Covered: US and Canada

Web Site: www.soyousa.com,

www.soyo.com

Sales:

Tel: 510-226-7696

Fax: 510-226-9218

Email : sales@soyosua.com

Technical Support:

Tel: 510-226-7696

Fax: 510-226-9218

Email : support@soyousa.com

SOYO (U.K.) LTD.

Unit 7, Alice Way, Hounslow Business

Park,

Hanworth Road, Hounslow, TW3 3UD

Region Covered: United Kingdom and

Republic of Ireland

Web Site: www.soyo.co.uk

Sales:

Tel : +44 (0)181 569 4111

Fax: +44 (0)181 569 4134

E-mail: sales@soyo.co.uk

Technical Support:

Tel : +44 (0)181 569 4111

Fax: +44 (0)181 569 4134

SY-7IWB

Quick Start Guide

E-Mail: support@soyo.co.uk

SOYO Deutschland GmbH

August-Wilhelm-Kuhnholz-Str. 15

D-26135 Oldenburg

Region Covered: Germany, Austria

and Switzerland. (Zustandig fur

Deutschland, Osterreich, Schweiz)

Web Site: www.saat.de, www.soyo-

saat.com, www.soyo-saat.de

Vertrieb Mainboards, Notebooks und

SoyoCom Produkte:

E-Mail: sales@soyo.de

Fon: +49-(0)441/20910-31/33

Fax: +49-(0)441/203422

Technischer Support:

E-Mail: support@soyo.de

Fon: +49-(0)441/20910-40

Fax: +49-(0)441/203422

SOYO KOREA

Region Covered: Korea

Sales:

Tel : 82-2-716-2850

Fax : 82-2-704-2619

E-mail : soyo@soyo.co.kr

Technical Support:

tel : 82-2-717-4392

fax : 82-2-712-5853

e-mail : soyok@chollian.net

SOYO Hong Kong

Region Covered: Hong Kong

Web Site: www.soyo.com.hk

Sales:

tel: 852-27109810

fax: 852-27109078

E-mail: soyo@hkstar.com

Technical Support:

tel: 852-27109810

fax: 852-27109078

E-mail: soyo@hkstar.com

SOYO China (Gin Mei Jei)

Region Covered: All of China

Sales:

Tel: 86-10-62510089

fax: 86-10-62510388

E-mail: soyo@public.bta.net.cn

Technical Support:

Tel: 86-10-62510089

fax: 86-10-62510388

E-mail: soyo@public.bta.net.cn

SOYO Japan

Region Covered: Japan

Web site: www.soyo.co.jp

Sales:

Tel: 81-3-33682188

Fax: 81-3-33682199

E-mail: soyo-jpn@soyo.co.jp

Technical Support:

Tel: 81-3-33682188

Fax: 81-3-33682199

E-mail: support@soyo.co.jp

Edition: July 1999

Version 1.0

SY-7IWB

SERIAL

SOYO SY 7IWB QSG 7iwb10 User Manual To The 4d3e6533 4489 4716 9e6d 90f29b1280d6

Navigation menu

Versions of this User Manual:

Views

Navigation