SPX Service Solutions J-50079-6 Wireless Inspection Camera and Receiver User Manual 8807AL

SPX Service Solutions Wireless Inspection Camera and Receiver 8807AL

Users Manual

Version 1.1Please read this user manual carefully before using this product. Failure to understand operation procedures may result in injury.Model: 8807ALModel: 8807ALEU Environmental ProtectionWaste electrical products shouldnot be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer forrecycling advice.Wireless Inspection Camera with Recordable MonitorINSPECTION TOOLTMTMINSPECTION TOOL
CONTENTS* 8807AL = GB8807(camera) + GB7307(monitor)0201SAVE THESE INSTRUCTIONS!※ Prevent object and liquid entry. Never spill liquid of any kind on the video display unit. Liquid increases the risk of electrical shock and damage to the product.※ The unit is not shock-resistant. Do not use Explorer Standard as a hammer and avoid high impact resultant from things such as dropping the unit from height※ Do not immerse camera handle or monitor in water. Avoid moisture, and store product in a dry place. Such measures reduce the risk of electric shock and damage. The lens and the tube are water resistant when the unit is fully assembled, but the monitor and handle are not.※ Do not use the camera if condensation forms inside the lens. Let the water evaporate before using again.※ Turn off the system if it is not in use.※ This product can only be completely disconnected for from its power source by unplugging the power adapter.※ Do not cut the DC power cable of provided with this product to fit with another power source.※ Attention should be given to the environmental aspects of battery disposal.※ Remove the batteries when cleaning the unit.※ Remove the batteries before storing the unit for a long time.※ When necessary, REPLACE ALL FOUR (4) BATTERIES in this unit with new ones, not one (1) or two (2) batteries at a time.※ Use only the size and type of battery specified.※ Be sure to install the battery with the correct polarity as indicated in the battery compartment.※ Properly dispose of batteries. Exposure to high temperatures can cause batteries to explode, so do not dispose of in a fire. Place tape over the terminals to prevent direct contact with other objects. ※ Some countries have regulations concerning battery disposal. Please follow all applicable regulations.GENERAL SAFETY INFORMATIONWARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. General Safety InformationWelcomeFeaturesPacking ListStructureInstallationOperation Basic Operation Recording Video Taking Photos Playback Video/picture Deleting Video/picture Deleting Folder How to Enter the Setting Mode Language Setting Video System Setting Formatting Default Setup View Version Information Frame Rate Setting Time Stamp Setting Recording Type Date/time Setting Event PlaybackSpecificationsTroubleshootingFCC Information020303040405080809090910101111111111121212121212131414
● Allows for easy surveying of small, hard-to-reach places.● Mini 4.5mm waterproof LED lens, 1 or 2 meter flexible tube.● Manufactured and tested to IP67 waterproof standard.● 3.5"TFT-LCD detachable/mountable monitor, built-in rechargeable Li-battery.● Video recording capability, supports up to 32GB micro SD card.● Adjustable brightness on lens-mounted LED light. ● Lightweight, handheld design, flexible and convenient to use.● Multi-language support.FEATURES0403STRUCTUREWELCOMECameraPower IndicatorPower SwitchSignal OutputBattery SlotFlexible Tube InterfaceCongratulations on your purchase of our inspection video camera with recordable color LCDmonitor, the EXPLORER PREMIUM. Please read the user manual carefully before using this product.This product is designed as a remote inspection device, capable of recording video/taking pictures. Appropriate for use in surveying pipes or other hard-to-reach places, equipment or furnishing installation, car repair, etc. Features include waterproof LED lens, real-time recording, and micro SD card storage.PACKING LISTFlexible TubeMini 4.5mm Waterproof LED LensVideo cable x 1Magnetic Bracket(Optional)Micro SD CardLCD Monitor x 1Handle x 1Power Adapter x 1USB cable x 1Flexible Tubex 11 meter 2 meterNote: only one of the two flexible tubes included in the package.
0605INSTALLATIONTo Install Batteries (Dry your hands before installation or replacing batteries.)1. Using a Philips head screwdriver, remove screw and cover as illustrated below:2. Remove battery compartment and insert four (4) AA batteries into their appropriate slots, with proper orientation, as indicated on the battery compartment.3. Reinstall battery compartment and replace battery cover and screwTo Attach Flexible Tube with HandleTo connect the flexible tube camera with control handle, first make sure that the keyed end of the tube is aligned with the slot in the handle, then use slight force to push them together. Once properly aligned, twist the treaded knob clockwise until the connection is securely in place.Fasten the treaded knobKeyed end plugs into socketTo Install Monitor for Wired UseEXPLORER PREMIUM supports wired use by connecting the monitor to the camera handle.Slide the monitor downwardInstalled successfullyMonitorVideo OutputPower JackMenuToggle DownConfirm Monitor Docking StationReset ButtonUSB PortMicroSD Card SlotToggle Up Power IndicatorPower SwitchTo Install Monitor Mounting BracketAttach the magnetic mounting bracket to the monitor using the same method used to attach the monitor to the camera handle.To Insert SD CardSD cardCD driver( G )3.5 Floppy Disk( A )Mobile Disk( H )After SD card is inserted into SD card slot successfully, an SD card icon will appear on the monitor screen; otherwise, the ‘no SD card’ icon will show.To Connect USB Cable Use the provided USB cable to connect the monitor to any PC with a USB slot. Your computer should automatically recognize the new hardware, which you may browse by double-clicking on the My Computer icon on your desktop, and then navigating into the Mobile Disk directory.
0807Insert video cable into the video out socket of the monitor, insert the other end of the cable intothe video in jack of any compatible TV or display device. The LCD monitor is now capable of outputting high quality video to another display.Video Output Twin LEDs provide lighting3. When in use, the tube should easily maneuver itself into position. Do not apply excessive force.To Connect Monitor PoweradaptermonitorpowersourceOPERATIONConnect the monitor to an appropriate (100-240V ~ 50/60Hz) power sourcewith the provided adapter. The power indicator LED will illuminate red and the battery capacity icon on the LCD will flicker, indicating that the battery is charging.When the red indicator light disappears, the battery has been fully charged.OKSelect CH4 Select to record video or take pictures1. As you roll the power switch to turn on the camera, the power indicator on the camera handle will light. The rolling switch then acts as a dimmer for the twin LEDs that surround the camera on the end of the flexible tube.2. Press and hold the power switch for 2 seconds on the monitor until the power indicator illuminates green. Then press the button to select CH4 (channel 4), or until the picture from the lens is displayed on the monitor. To toggle between video recording and picture taking functions, press the button on the side of the monitor.Basic Operation1. In real-time monitoring mode, press the button to toggle to video recording mode.2. Press the ‘OK’ button to begin recording:3. Press again to stop recording.Recording Video* The video will be automatically saved as an individual file every 30 minutes.* The icon indicates that the SD card memory is full.CH4 [00:05:43]2009/02/1114:50:40 2009/02/11 14:50:40Time StampRecordingRecorded TimeBattery CapacityVideoIconCurrent ChannelSD Card IconCurrentDate/TimeNotice!
Playback Video/Picture1. In real-time monitoring mode, press the button to toggle to the video/picture folder.2. Press the and buttons to select your desired folder, and then the press ‘OK’ to toggle to the right interface: A double quotation marks ( ” ) next to a file name indicates that the file is a picture. No double quotation marks next to a file indicates that the file is a video. Notice!05:53:00 CH405:53:03 CH405:56:40 VID05:59:03 CH4"06:05:17 VID"05:53:00 CH4"2009-01-10 0002/0005Indicates video fileIndicates picture fileOK:2009/01/10 05:53:00 :3. for playback video: Press the or button to select your desired video, and then press ‘OK’ to playback. Pause: press the ‘OK’ button once to pause, press again to resume play; Fast Forward: press the button; Rewind: press the button; Stop/Exit: press the button. for view pictures: Press the or button to select your desired video, press ‘OK’ button to view and press again to exit. 2009-01-10 0002/000505:53:00 CH505:53:03 CH505:56:40 CH505:59:03 CH506:05:17 CH505:53:00 CH5DELETE CURRENT FILE?NOYESDeleting Video/Picture1. In real-time monitoring mode, press the button to toggle to the video/picture folder.2. Press the or button to select your desired folder, and then press ‘OK’ button. 3. Press the or button to select your desired file, and then press and hold the button for 2 seconds, or until the right interface appears:4. Press the or button to toggle between YES and NO, that is, to delete or cancel. Once you have highlighted your desired selection, press the ‘OK’ button.PLAYBACK 0001/00072009-01-102009-01-122009-02-052009-02-092009-02-112009-01-11FOLDER NOT EMPTYDeleting FolderDeleting a folder is done in the same way as deleting a single file, however, make sure that the folder is empty first, otherwise the following error message will appear:PhotoIconTaking photosThe icon indicates that the SD card memory is full.1. In real-time monitoring mode, press the button to toggle to photo capturing mode.2. Press the ‘OK’ button to take a photo.Notice!1009SYSTEM SETTINGHow to enter the Setting ModeIn real-time monitoring mode, press and hold the button for 1~2 seconds, or until the right interface appears:
OK: EnglishLanguage1. In the setting mode, press the or button to select ‘SYSTEM SETTING’, and then press ‘OK’ button.2. Press the or button to select ‘Language’, and then press ‘OK’ button, the following interface will appear: 3. Press the or button to select your desired language.4. Press ‘OK’ button to confirm and exit.Language SettingVideo System Setting 1. In the setting mode, press the or button to select ‘SYSTEM SETTING’, and then press ‘OK’ button.2. Press the or button to select ‘Video System’ and then press ‘OK’ button.3. Press the or button to toggle between NTSC and PAL. Once your desired system is selected, press ‘OK’ button to confirm and exit.Formating1. In the setting mode, press the or button to select ‘SYSTEM SETTING ’, and then press ‘OK’ button.2. Press the or button to select ‘Format’, and then press ‘OK’ button.3. Press the or button to toggle between YES and NO, that is, to format or cancel. Once you have highlighted your desired selection, press the ‘OK’ button.Default Setup1. In the setting mode, press the or button to select ‘SYSTEM SETTING ’, and then press ‘OK’ button.2. Press the or button to select ‘Default Setup’ and then press ‘OK’ button. 3. Press the or button to toggle between YES and NO, that is to restore default or cancel. Once you have highlighted your desired selection, press the ‘OK’ button.View Version Information1. In the setting mode, press the or button to select ‘SYSTEM SETTING’, and then press ‘OK’ button.2. Press the or button to select ‘Version’ and then press ‘OK’ button. You will now be able to view the version details of your product.Frame Rate Setting1. In the setting mode, press the or button to select ‘RECORDER SETTING’, and then press ‘OK’ button.2. Press the or button to select ‘Frame Rate’ and then press ‘OK’ button. 3. Press the or button to toggle between different frame rates. Once your desired rate is selected, press ‘OK’ button to confirm and exit.Time Stamp Setting1. In the setting mode, press the or button to select ‘RECORDER SETTING’, and then press ‘OK button’.2. Press the or button to select ‘Time Stamp’ and then press ‘OK’ button. 3. Press the and buttons to toggle between on and off. Once your desired selection is made, press ‘OK’ button to confirm and exit.Recording Type1. In the setting mode, press the or button to select ‘RECORDER SETTING’, and then press ‘OK’ button.2. Press the or button to select ‘Recording Type’ and then press ‘OK’ button. 3. Press the or button to toggle between ‘still’ and ‘video’. Once your desired selection is made, press ‘OK’ button to confirm and exit. Date/TimeOK:2009 / 02 / 13 09 : 51Date/Time Setting1. In the setting mode, press the or button to select ‘Date/Time’ and then press ‘OK’, The right interface will appear:2. Press ‘OK’ button to select Date or Time; Press the or button to adjust selection; Press the button to confirm and exit. Event Playback1. In the setting mode, press the or button to select ‘EVENT PLAYBACK’, and then press ‘OK’ button.2. Refer to user manual instructions on Playback of Video/Picture, Deleting Video/Picture, and Deleting Folder for guidance. 1211
1413FCC INFORMATIONThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference; (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.The graphics included in this user manual are subject to minor change without notice.SPECIFICATIONS* Actual transmission range of wireless monitoring may vary according to the weather, location, interference or building construction.* All specifications are subject to minor change without prior notice.0 Lux4 x AA batteriesCMOSPAL/NTSC3.5″TFT-LCD 960 x 240700mA5VDC100 x 70 x 25 (mm) 140g15~85%RH-10 ~40OOCCFM0.9-1.3VP-P@75ohm≤-85dBm2468MHz 18MHz10m (max.)186 x 145 x 41(mm) (Excluding Flexible Tube) IP67 (for lens/tube only)8807AL 63o320 240 x 231g4.5mmMinimum Illumination Horizontal Viewing Angle LCD Screen TypeEffective PixelsVideo SystemConsumption Current (Max.)Exterior Supply Voltage Dimensions (W x D x H)Approx. WeightImaging SensorEffective PixelsModulation TypePower SupplyApprox. WeightOperating TemperatureOperating Humidity (Max.)Video Output LevelWaterproof CapacityReceiving SensitivityTransmission FrequencyBandwidthUnobstructed Effective RangeModel No.Dimensions (W D H)x x Tube Diametercameramonitor2414MHz,2432MHz,2450MHz,2468MHz3 hoursCharging Time2 hoursWorking TimePicture/Video Pixels 640 x 480Video Size 27M byte/minuteFrame Rate 30 frame/secondProblem Possible Causes Likely SolutionsTool will not startMonitor will not chargeImage too dark or light1. charge monitor2. replace batteries in control handle1. make sure adapter cable is connected be t w e en mo n i t or an d a d apter.2. make sure adapter is securely plugged into wall socket.1. use dial on control handle to adjust brightness of LEDs.2. use contrast and brightness buttons on monitor to adjust image.1. monitor not charged. 2. batteries need charging.1. adapter cable not attached properly2. adapter not connected to power1. LEDs near camera need adjustment2. monitor display needs adjustmentTROUBLESHOOTINGFollow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service.!Receiving Frequency

Navigation menu