ST Electronics HB190 Microwave Motion Sensor User Manual

ST Electronics (Satcom & Sensor Systems) Pte Ltd Microwave Motion Sensor Users Manual

Users Manual

Download: ST Electronics HB190 Microwave Motion Sensor User Manual
Mirror Download [FCC.gov]ST Electronics HB190 Microwave Motion Sensor User Manual
Document ID1017251
Application ID3R3NdE3B6wIvkCMhzEpixQ==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize40.8kB (509999 bits)
Date Submitted2008-10-17 00:00:00
Date Available2008-10-17 00:00:00
Creation Date0000-00-00 00:00:00
Document Lastmod0000-00-00 00:00:00
Document TitleUsers Manual
Document CreatorHewlett Packard MFP

Satcom & Sensor Systems HB190
ST Electronics (Saicnmnmnrsvmmsiere Ltd X-Band Microwave Motion Sensor Module
lllflJumng EastSoeetZl. SYElectmvnchumnq EastEuiIding Level 4, Singapore 1mm User Manual
Tet-lsspssmmr Fax-mmwrm Ema lsense@stee.stennqcom
Webstte.mv\v.agt’:>.uv”it to,” you?»
V1.00
Intrutlt on
HBIOO microwave motion sensor is a X-Band Bi-Static Doppler transceiver module that
makes use of Doppler Effect Principle to detect motion. These modules are designed for
movement detection, like intruder alarms, occupancy modules and other innovative ideas
“(0
fissiluw'
The module consists of Dielectric Resonator Oscillator (DRO), microwave mixer and
Dipole antenna (see Diagram A).
This User Manual highlights some imponant points when designing-in HBl90 module.
Diagram A: Block Diagram
Terminal Pins can be used to connect the terminals (+5V, IF, GND) to amplifier circuits as well as mounting support. Other
mounting methods may be used.
Wave-soldering the module onto PCBA is possible but processes have to be evaluated to prevent deterioration. No-cleaning
process is recommended.
Caution must be taken to avoid applying pressure or stresses to the chassis of the module as it may cause performance
deterioration.
1. Power Su lv&Connection
The module operates at +5Vdc for Continious wave (CW) operation.
The connections are shown in the diagram on the right.
4. Radiation Pattern
The module is to be mounted with the patch antennas facing the desired
detection zone. ,/
The user may adjust the orientation ofthe module to get the best coverage. ,.
The radiation patterns ofthe antenna are shown in the diagram on the right. §\
Doppler shift - Doppler shifi is the output from H“ terminal when movement is detected. The magnitude ofthe Doppler Shift
is proportional to reflection of transmitted energy and is in the range of microvolts (pV). A high gain low frequency
amplifier is usually connected to the IF terminal in order to amplify the Doppler shift to a process able level. Frequency of
Doppler shitt is proportional to velocity ofmotion. Typical human walking generates Doppler shifi below 100 Hz.
«M .
ems ST Electromcs
A company of ST Engineering
| A4“)
Satcom 8: Sensor Systems HB190
ST Electronics iSaIcnmESensor Systems] Pte Ltd X.Band Microwave Motion Sensor Module
lWJuvong EastSlreelZl. st Eieurmicstumnq East Building LeveN Singapore storm User Manual
Tel .165l6567 57m Fax1l65755€76370 Email 1 aqrisenseixstee stengg com
Website .thw agllsense can. I Reg") 997mm”
V] .00
6. Reference
notion
srnsun
cno
Microwave radiation from the module is well below established safety standards for general public environment, like ANSI
C95.1-19910fUSA and NRPB-Gll ofUnited Kingdomr
Handlm'
The module has been fully tested to specifications Upon opening, tighten or loosen the chassis will cause performance
deterioration.
The module is an electrostatic sensitive device (ESD). Precautions shall be observed for handling and assembly.
Please contact our product support engineers in the factory for technical assistance whenever necessary.
Product Support (Microwave Sensors)
Tel: (65) 6568 7414
Fax: (65) 6567 6370
E-mail: agilseme@stee.stengg.com
This device complies with part 15 ofthe FCC Rules.
Operation is subject to the following two conditi 1) This device may not cause harmful interference. and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications to ST Electronics equipment not expressly approved by ST Electronics could void
the user authority to operate the equipment.
$2“; ST Electronics
Acumpany aisr Engmeermg
’7 rd”?

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Creator                         : Hewlett Packard MFP
Create Date                     : 0000:01:01 00:00:00
Author                          : 
Producer                        : 
Title                           : 
Subject                         : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: VECHB190

Navigation menu