ST Engineering Telematics Wireless T210A RF module for RF mesh network User Manual User manual 28384x

Download:
Mirror Download [FCC.gov]
Document ID	3156507
Application ID	dyCV4185T/vxGlPli6reLg==
Document Description	Users Manual revised
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	35.73kB (446582 bits)
Date Submitted	2016-10-06 00:00:00
Date Available	2016-10-06 00:00:00
Creation Date	2017-12-15 19:47:58
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-15 19:47:58
Document Title	Microsoft Word - User_ manual_28384.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Marina

Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
17 JULY 2016
Model: TNET210
User Manual
Rev 1.0
Page 1 of 8
Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
Module description
The TNET210A is a RF module to be inserted in Telematics Wireless streetlight
control products. The TNET210A can be configured to be a gateway or a node in
Telematics Wireless propriety mesh network.
LED indicators
Tx mode
D2 red LED is lit when transmitting data.
Rx mode
D1 green LED is lit when receiving mode is enable.
RF Specification
Frequency band
902‐928MHz
Modulation
2GFSK
Output power
27dBm max
Bit Rate
110kbps
Page 2 of 8
Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
Power consumption
Tx mode
420mA, 3.6V
Rx mode
40mA, 3.6V
Physical description
Dimension LxWxH
52.5x28.3x8.6 mm
Weight
10 gram
Environment
Operating Temperature
‐40 to +85deg.C
Certifications
Radio
47CFR FCC Part 15 subpart C section 15.247/RSS‐247
EMC
47CFR FCC Part 15 subpart B / RSS‐Gen issue 4, ICES‐003 Issue 6
Antenna Specification
Frequency range
902‐928MHz
Gain
+2dBi
Polarization
Vertical
Impedance
50 ohm
VSWR
2:1
Radiation
omni directional
Page 3 of 8
Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
Regulatory Information
FCC Part 15 Regulation Class B device
The digital circuit of this device has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Class B Notice
This device complies with Industry Canada’s licence‐exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
Page 4 of 8
Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
FCC interference Notice
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
FCC and Industry Canada Radiation Hazard Warning
The antenna used for this transmitter must be installed to normally provide
minimum separation distance of at least 20 cm from all persons.
Le dispositif doit être placé à une distance d'au moins 20 cm à partir de toutes les
personnes au cours de son fonctionnement normal. Les antennes utilisées pour ce
produit ne doivent pas être situés ou exploités conjointement avec une autre
antenne ou transmetteur.
Requirements for the antenna with regards to FCC/IC compliance
This radio transmitter (IC:4732A‐T210A) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC:4732A‐T210A) a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci‐dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain
est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation
de l'émetteur.
Antenna manufacturer
V.torch
Model no.
VTGSMA‐70
Gain
2dBi
Page 5 of 8
Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
OEM Integrators Notices
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co‐located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end‐product for any
additional compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions cannot be met (for example
certain laptop configurations or co‐location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible for re‐
evaluating the end product (including the transmitter) and obtaining a separate FCC
or authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users (for
example: wireless AP, wireless Router).
The final end product must be labeled in a visible area with the following: “Contains
TX FCC ID:NTAT210A; IC:4732A‐T210A”.
OEM Manual Information That Must be Included
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the users manual of the end
product which integrate this module.
The users manual for OEM integrators must include the following information in a
prominent location:
“IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the
antenna used for this transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co‐located or operating in
conjunction with any other antenna or transmitter."
Page 6 of 8
Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
Installation Instruction
Warning: The user and Installer should be aware that changes or modifications to
this equipment not expressly approved by Telematics Wireless could void warranty
and the user’s authority to operate the equipment.
Professionally trained personnel should install the equipment.
Installation in DCU2 PRO E host
1. Connect the TNET 210 module on board
2. Connect the SOM on board.
Page 7 of 8
Telematics Wireless Proprietary
FCC ID:NTAT210A
IC: 4732A‐T210A
3. Close the internal cover of the DCU2 PRO E.
4. Close the external cover of the DCU2 PRO E.
5. The DCU2 must be equipped with a permanently affixed label showing the module
identification as follows:
Contains:
FCC ID:NTAT210A
IC:4732A‐T210A
Page 8 of 8

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : Marina
Create Date                     : 2016:09:29 09:04:07+03:00
Modify Date                     : 2016:09:29 09:04:41+03:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 10.1.16 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2016:09:29 09:04:41+03:00
Format                          : application/pdf
Title                           : Microsoft Word - User_ manual_28384.docx
Creator                         : Marina
Document ID                     : uuid:b8fe7e67-4f89-4988-8e87-c7ca42b2823b
Instance ID                     : uuid:10877fad-e7a4-459d-bf36-8121837fbfb1
Page Count                      : 8

EXIF Metadata provided by EXIF.tools