STEELMATE BSE0001 Tire Pressure Monitoring System User Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	1687933
Application ID	fShSu31GK4Jrx1X4dPOgOQ==
Document Description	User manual-2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	346.88kB (4336017 bits)
Date Submitted	2012-05-02 00:00:00
Date Available	2012-05-02 00:00:00
Creation Date	2012-05-02 14:19:23
Producing Software	Adobe Acrobat Pro 10.1.1
Document Lastmod	2012-05-02 14:19:58
Document Title	User manual-2
Document Creator	Adobe Acrobat Pro 10.1.1

Sensors programm ng f
The sensors ottnts system are programmed by
the display.
1) Remove the display trom the holder
2) Press ‘< , N 1A" buttons to choose the tire
which you went to progmm The corresponding tire
icon "I" will flash
Flash
3). Place the display close to the sensor (The distance
should be: 10—30 cm), then press and hold the “SET"
button tor more urah 2 secorids, the roon “LF” will be
showed on the display to indicate the programming
start
4) lh 1—2 seconds, it will indicate ure programmingrs
successful alter two beeps heard (lithe programming
is not sumsssful in 6~8 seconds the display will give
a short beep to indicate) The programmed tire icon
1" will stop flashing, and the corresponding tire
pressure and temperature will be showed on the
display
5) Repeat the steps 2—4 tor other sensors
6) When all the sensors are programmed successful,
reconnect the drspley to the holder
Note.-
1. The sensors in this unit have been rndruidually preset
tor each tire in the tactory Once the labeled sensors
are installed in the correspondrng tires, there will be no
need to program the sensors
2 When programmrng, the drsplay should be placed
to the sensor as close as posslble Make sure there
is not another sensor wrthin 30 cm
3 One sensorcan only be programmed to onetire lt
a sensor is programmed to a wrong posrtion ottire, you
need to reconnect the drspley to the holder tor resale
and then reprogram the sensor
How does the system work
Self-test function of the display
Once ACC is turned on the display wrll turn on wrth
backlight on, and perform self-test All icons and
symbols will be checked and the system enters the
standby mode. The display will show the intormation
oteaoh tire which has been programmed one by one
(4 seconds tor each tire)
Alarm warning for abnormal tire conditions
1) When the trre pressure is hrgher than High P5 or
Lower than Low PS and/or the tire is leaking fast, the
corresponding tire icon tire pressure r ading and
alarm symbol 1: will llash The drsplay will send out
“bihibi' tor warning (once per 5 seoonds) and stay at
the image or the warning tire Press any button to
pause the alarm Then the display will send out “hibisbi'
tor warning once per 1 mrnute lt there are more than
two abnomtal tires are warning, the display will showed
the informafion olsadw firs drujlany (one peril seconds)
Flash
2) When the tire temperature exceeds the High
Temperature, the corresponding tire icon “I tire
temperature reading and alarm symbol W will
flash The display will send out “bi ' r"torwamrng
(once per 1 minute) and stay at the image oi the
warning tire it there are more than two abnormal
tires are weming. the display will showed the inf-
ormation or each tire circularly (one per4 seconds)
Flash
Low sensor battery warning
When the battery ofthe sensor is low. the correspo-
nding tlre icon “I battery icon "(E'will flash.the
system will beep 5 times and repeat twrce, then stop.
Am that, the system will not send out warning for the
low battery tire until the ACC turn on again and the
display performs sellslest (When there are several
tires are low battery the system will warn for them
simultaneously)
Abnormal sensor
if there is no tire intonrration received trom a specific
tire ln an mrnutes, the sensor which was rnstalled in
this tire is considered as abnormal sensor The corre
sponding tire icon ‘|' wrll flash, the “FF‘ icon will be
showed on the display The tire ioorr 1 will disappear
afler 5 beeps heard The system will stop warning and
restore to circularly show information of other tires
The tlrs lnformalion which installed abnormal sensor
will not be showed and warning again until the ACC
mm on again and the display performs sertoest lflhe
system detects a specific tire with abnormal sensor
when not: turns onto times continuously, the system
will not alarm tor this tire nexttlme when ace turn on
egarn
Nple- Product compo s
a ll them 978 several warnings lar tires al ms sams
lirne (High Ps, low Ps, high Temperalure, lire
pressure leaking fasr and so on), llre system will
give priorily re pressure warning (lasl leaking)
- wnen ACC rum on («he display is connecreu re
rne holder), all corresponding abnormal rire icon 1"
will flash 3~s seconds anne sarne rime And then
me display will slay al the image or lire wnicn is
warned lor abnormal pressure or pressure leaking
fasl. The syslsnr will beep 3 Ilmss per 5 ssepnds
Press user bunon. Ihe syslem wlIl lurn Io beep 3
rimes perl minule, and Ihen snow the rniormalren
ofabnormal rires circularly.
- lf inere is no warning for rire pressure, lne display
will no! sray ar the image of any lire when ACC turn
on (lire display is connecled lo the holder)
TPM 3 Wire lie
Installation Manual
ul Valve cap
1, e , ,-l,\l§u§,
Valve stem
10
Repeater nstalla
Place the alsplay m a goud vlew posmon (see lhree rewmmended pesmens
in (he dlagram) Having a 90 vlew angle with lhe display supplles the best
vlslblllly.
Fuse
0 ACC +12DC
G Baltery+lzbc
Q3 GND
Blue
Cunnecl lhe msplay lo the 12 Vell power
12
a Repealer position
(Repeater)
Repealer should be inelalled ellhe poslerler unhe car ll can‘t be irlslalled lronl or lhe rear enhe car
Please let lhe antenna away from melal lo Evold affeclrng me slgnal.
Install me sensor:
Remove lhe onglnal valve lram lhe wheel ane replace wllh
lheTPMS sensors On each sensor. there ls asnrkerslwng
NOTE' The haw recummended lemue range hr whrch hre me senear should be lnslallec Hand llgmen the
2 sensnr o erl hlenn canca se lean or ma break the
TPMS valve ls 2 3~2 9 NM 0r23 45-29 57kchm sense,“ " ‘9 ‘ 9 U y
Remove the mes from the vemcle
System installa gram
Balance the wheels:
The wheels need in be blanced aner TPMS sensors are installed
After installation, turn an engine and perform a test.
III \ IE.
(I; [I {I3- I. IE.
“ II “ III II
n E m
5 sensor lnsLaHallon poslllon 10 sensor lnsLaHallon poslllon
I: If!“ n- “-
(a II film {I}! I3.- B“
B In E- u “Ill “-
an j -a “B
1A sensor inslallanan posmon
22 sensor inslal latlon position
we sensor lnstallallnn posmcn
ble
1.Atlerlhe installation, lhere is no tire inlonnation
on the display?
1) The sensors are not programmed to the display.
please reprogramm the sensors
2) The display is not turned on
2. When ace is turned on, there is tire
information on the display but the tire symbol
is flashing slowly.
The display shows the prevrous tire information.
Once the new tire information is received. the tire
symbol Wlll stop flashing
3.There is no tiro invormation for a specilic
tirs.
1). There is a problem With the sensor.
2). The sensor is not programmed to the display.
The unit is warranted for A Iimiled period Df
iime fmm the date a purchase. In the unlikely
event ola defect ari ng in this product when
used in accordance with the manufacturer's
instructions, the parts would be repaired or
replaced tree or charge.
a) it is required to show warranty card when
Warranty terms
maklng any warranty claims.
bl The model and the unit‘s serial number must
be the same as the inlormation on the warranty
card
This wananty is mn-banslembh and isautomatically
void il:
3) The original purchaser has not completed the
warranty card.
bl The unll‘s serial number is defaced, missing
or altered.
c) The unit has been mudilled or used in a manner
contrary to its intended purpose
d) The unit has been damaged by accident,
unreasonable use, neglect, improper installation
or service
The warranty does not covlr:
a) Damage caused by incorrect or poor installation
problems which may be caused by anomalies
in the vehicle‘s electrical system or originating
lrom the environment in which the system is
operated
to) Damage to the system caused by accident or
improper use in any manner whatsoever not
the fault. including but not limited to damage
by water or as a result or excess voltage applied
to the system or it misused or repaired or
altered in any way otherthan or ll‘s authorized
agent
c) False inlonnation displayed in the panel olthe
dash board that is caused by carvvith CAN bus
system.
Warranty Card
Dear user:
Thank you lor choosing this product
Please fill the form below and retain it
User's in'ormaiion:
User
Tel
Vehicle license No.
Product model No-
Serial Nd.
Date of installation.
Name of the retailer-
signed by distributor-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2012:05:02 14:19:23+08:00
Creator                         : Adobe Acrobat Pro 10.1.1
Modify Date                     : 2012:05:02 14:19:58+08:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2012:05:02 14:19:58+08:00
Creator Tool                    : Adobe Acrobat Pro 10.1.1
Format                          : application/pdf
Document ID                     : uuid:06aa815b-b63e-4e06-af8f-ac3d9b815b57
Instance ID                     : uuid:8b044e33-281f-46f1-af46-ee1e309bfa41
Producer                        : Adobe Acrobat Pro 10.1.1
Page Count                      : 5

EXIF Metadata provided by EXIF.tools