SWISHER Mower Deck Manual LR708249
User Manual: SWISHER SWISHER Mower Deck Manual SWISHER Mower Deck Owner's Manual, SWISHER Mower Deck installation guides
Open the PDF directly: View PDF 
.
Page Count: 16
www. swisherinc.com
OWNER'S
MANUAL
STARTING SERIAL #:
L106-038001
MODEL NO.
T1360B1
T1360T
T1360H
T1360K
T13560
RK1360
T14560
T17560
T18560
_ IMPORTANT
Read and follow all
Safety Precautions
and Instructions
before operating this
equipment.
Rev 07-151 j
60" FINISH CUT
TRAILMOWER
!ATRADITION OF QUALITY SINCE 1945 f
Assembly
Operation
Service and Adjustment
Repair Parts
P.O. BOX 67, WARRENSBURG, MISSOURI 64093 PHONE 660-747-8183 FAX 660-747-8650
Manufacturing quality lawn care equipment since 1945
3lade h_ The 1
J
USA
10809
LIMITED WARRANTY
The manufacturer's warranty to the original consumer purchaser is: This product
is free from defects in materials and workmanship for a period of one (1) year
from the date of purchase by the original consumer purchaser. We will repair or
replace, at our discretion, parts found to be defective due to materials or
workmanship. This warranty is subject to the following limitations and
exclusions:
l) Engine Warranty All engines utilized on our products have a separate
warranty extended to them by the individual engine
manufacturer. Any engine service difficulty is the
responsibility of the engine manufacturer and in no
way is Swisher Mower Co., Inc. or its agents
responsible for the engine warranty. The Briggs &
Stratton Engine Service Hot-Line is 1-800-233-
3723. The Tecumseh Engine Service Hot-Line is 1-
800-558-5402.
2) Commercial Use The warranty period for this product used for
commercial or rental is limited to ninety (90) days
from the date of original purchase.
3) Limitations This warranty applies only to products which have
been properly assembled, adjusted, and operated in
accordance with the instructions contained within
this manual. This warranty does not apply to any
product of Swisher Mower Co., Inc., that has been
subject to alteration, misuse, abuse, improper
assembly or installation, shipping damage, or to
normal wear of the product.
4) Exclusions Excluded from this warranty are normal wear,
normal adjustments, and normal maintenance.
In the event you have a claim under this warranty, you must return the product to
an authorized service dealer. All transportation charges, damage, or loss incurred
during transportation of parts submitted for replacement or repair under this
warranty shall be borne by the purchaser. Should you have any questions
concerning this warranty, please contact us toll-free at 1-800-222-8183. The
model number, serial number, date of purchase, and the name of the authorized
Swisher dealer from whom you purchased the mower will be needed before any
warranty claim can be processed.
SAFETY PRECAUTIONS
This Safety Alert Symbol indicates important messages in this /
manual. When you see this symbol, carefully read the message that I
follows and be alert to the possibility of personal injury. |
J
Read this manual completely. This machine can amputate hands, feet, and throw
objects. Failure to observe the following safety instructions could result in serious
injury or death.
• Read the manual. Learn to operate this machine safely.
• Always disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to
prevent accidental starting the engine when setting up, transporting, adjusting or making repairs.
• Keep all shields and guards in place.
• Understand the speed, steering and stability of this machine. Know the positions and operations of all
controls before you operate this machine. Check all of the controls in a sate area before starting to work
with this machine.
• Allow only responsible adults who are familiar with these instructions to operate this machine. Never
allow children to operate this machine.
• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and thrown by the blade.
• Be sure the area is clear of other people before mowing. Be aware of the mower discharge direction and
do not point at anyone. Stop the machine if anyone enters the mowing area. Children are often attracted
to the machine and the mowing activity. Never assume that children will remain where you last saw
them. Keep children under the watchful care of another responsible adult.
• No riders!
• Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
• Do not mow in reverse. Always look down and behind before and while backing.
• Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the
engine.
• Watch for traffic when operating near or crossing roadways.
• Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates
excessively. Excessive vibration is an indication of damage. Repair mower as necessary.
• Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid
shoes with good traction when mowing.
• Do not operate the machine while under the influence of alcohol or drugs.
• Operate self-propelled machines up and down slopes. There is significant risk of overturns when
operating across slopes. Operate walk-behind machines across slopes. There is a significant risk of
slipping under a walk-behind machine when operating up and down slopes. Do not operate on slopes
greater than 15 degrees.
• Never tamper with safety devices. Check their proper operation regularly.
• Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.
• Never make adjustments or repairs with the engine running.
• Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra caution when
servicing them.
WARRANTY RIGHTS AND OBLIGATIONS
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The California Air Resources Board and Swisher Mower, is pleased to explain the
evaporative emission control system (EECS) on your model year 2006 and later Swisher Product. In California, new Outdoor Power Equipment,
nmst be designed, built and equipped to meet the State's stringent anti-smog standards. Swisher Mower must warrant the EECS on your Power
Equipment, for the period of time listed below provided there has been no abuse, neglect, or improper maintenance. For model year 2006 the
EECS on your mower includes the liquid libel lines, libel line connectors, and libel line clamps. Where a wan'antable condition exists, Swisher
Mower will repair at no cost to you. Expenses covered under warranty include diagnosis, parts, and labor.
MANUFACTURER'S WARRANTY COVERAGE: For a period of two years, any evaporative emission-related part included in the
list of EECS parts for your mower is defective, the part will be repaired or replaced by Swisher Mower.
OWNER'S WARRANTY RESPONSIBILITIES: As the owner of this Power Equipment, you are responsible for performance of the
required maintenance listed in your owner's manual. Swisher Mower recommends that you retain all receipts covering maintenance
on your Power Equipment, but Swisher Mower cannot deny warranty solely for the lack of receipts. As the Power Equipment owner,
you should be aware that Swisher Mower, may deny you warranty coverage if your Power Equipment, or a covered part has failed
due to abuse, neglect, or improper maintenance, unapproved modifications, or the use of parts not made or approved by the
equipment manufacturer. You are responsible for presenting your Power Equipment to an authorized Swisher Service center as
soon as the problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you
have a question regarding your warranty rights and responsibilities, you should contact the Swisher Mower Service representative at
1-800-222-8183.
WARRANTY COMMENCEMENT DATE: The warranty period begins on the date the Power Equipment Is purchased.
LENGTH OF COVERAGE: This warranty shall be for a period of two (2) years from the initial date of purchase.
WHAT IS COVERED: Warranted parts include the Liquid fuel line, fuel line connectors, and fuel line clamps.
REPAIR OR REPLACEMENT OF PARTS: Repair or replacement of any evaporative warranted part will be performed at no charge
to the owner at an authorized Swisher Mower Service Center. If you have a question regarding your warranty rights and
responsibilities, you should contact your nearest authorized service center or call the Swisher Mower Service representative at 1-
800-222-8183.
WARRANTY PERIOD: Any warranted part is not scheduled for replacement as required maintenance, or which is scheduled only
for regular inspection to the effect of "repair or replace as necessary" shall be warranted for two (2) years. Any warranted part that
is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled
replacement point for that part.
DIAGNOSIS: The owner shall not be charged for diagnostic labor that leads to the determination that a warranted part is defective if
the diagnostic work is performed at an authorized Swisher Service Center.
CONSEQUENTIAL DAMAGE: Swisher Mower, may be liable for damages to other engine or equipment components caused by the
failure of a warranted part still under warranty.
WHAT IS NOT COVERED: All failures caused by abuse, neglect, or improper maintenance is not covered.
ADD-ON OR MODIFIED PARTS: The use of add-on or modified parts may be grounds for disallowing a warranty claim. Swisher
Mower is not liable to cover failures of warranted parts caused by the use of an add-on or modified part.
HOW TO FILE A CLAIM: If you have a question regarding your warranty rights and responsibilities, you should contact your nearest
authorized service center or call Swisher Mower Service representative at 1-800-222-8183.
4
SAFETY DECALS
Replace decals immediately if damaged.Order by part nmnber from Swisher Mowers
OD45- Warning Decal
OD 1l- No step Decal
OD55- Triangle Danger Decal
OD43- Flying Debris Decal
OD33- Speed Decal
OD29- Danger Decal
REQUIRED ASSEMBLY
FRONT WHEEL CASTER ASSEMBLY
1. Remove single nut and washers from caster shaft.
2. Place one washer on the shaft of the caster/wheel sub-assembly.
3. Slide same shaft through the bearing/frame with wheel towards the ground.
4. Place the other washer on the shaft; it should be resting on the top bearing.
5. Thread nyloc jam nut onto shaft.
6. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut. Over-
tightening of this nut will bind caster.
7. Repeat process tbr other front side.
REAR WHEEL ASSEMBLY
1. Remove cotter pin from axle.
2. Slide washer [ NB149 ] if necessary and wheel[ valve stem out] onto axle and replace
cotter pin.
3. Bend cotter pin so it will not Ihll out.
4. Repeat process tbr other wheel.
OFFSET & CENTER TOW HITCH BAR ASSEMBLY
1. Lay out parts according to the diagram.
2. Insert part 661A into part 662 and pin with the hitch pin (H11).
3. Insert part 661 into part 661A. Choose from the 3 holes to set the desired hitch length.
Pin with a hitch pin.
4. Part 662 slides into the front tube of the frame. Again, choose from the 3 holes to arrange
desired oft;et. Pin with a hitch pin (H11).
5. Eliminate step 3 tbr hitching from the center bracket. Only one method can be used at a
time.
\
OFFSET TOWING
POSITION
CENTER TOWING
POSITION
ATV or Utility
Vehicle Attachment
Instructions
Existing Rear Hitch. Bent Pin, Hair Pin
and Receiver
supplied by others.
OPERATING YOUR TRAILMOWER
The operation of any mower can produce foreign objects to be thrown into the
eyes, resulting in severe eye damage. Always wear certified safety glasses or
wide-vision safety goggles over spectacles before staring any cutting machine and
while operating such a machine.
The operation of any cutter produces sound waves that are damaging to the
human ear. Ear protection is recommended.
CAUTION!
Tragic accidents can occur if the operator is not alert to the presence of
children. Children are often attracted to the machine and the mowing
activity. Never assume that ehihlren will remain u,here you last san, them.
INTENDED USE
This TrailMower is designed to produce a quality finish cut on lawns, golf courses, etc.
It is not designed to clear brush or cut saplings. Your TrailMower should be towed
behind an ATV, a golf cart, lawn tractor, or similar approved vehicle. It is not meant for
speeds exceeding 5 MPH.
ATTACHING TRAILMOWER TO TOW VEHICLE
• Place mower behind vehicle and back vehicle up to desired attaching position.
• When offsetting TrailMower do so to side opposite the discharge of the tow
vehicle.
• Bolt swivel hitch (H10) to vehicle tow receiver.
• Attach tow hitch (661) to the swivel hitch with hitch pin (H 11). Make certain
hitch pin goes completely through each piece and is clipped to prevent accidental
separation.
• Attach red safety tether (H9C) to both the towing vehicle and to the TrailMower
toggle switch (685SP), located on the throttle housing (6013). Its purpose is to
manually stop mower engine or to stop mower engine in case the two machines
become separated. (See Motor Base Detail #22).
•It is extremely important the safety tether is secured properly to both the
toggle switch and the towing vehicle.
STARTING THE ENGINE
See engine manufacturer's instructions for the type and amount ofoil and fuel used.
TrailMowers with electric start engines will need a battery (sold separately). Swisher
recomlnends using a standard "U 1 R" lawn & garden battery.
• Engine must be level to accurately check and fill oil. Do not overfill.
• Makesurethetow vehicleparkingbrakeis set,mowerislevel, andbladesare
disengaged.
• Checksparkplugwire, oil, andfuel.
• Checkall electricalconnections(SeeSchematics).
• Makesuretoggleswitchis turned"ON" andtheredtetherisproperlyattached.
• Setengineidle to "CHOKE" position.
• With feetclearof mowerdeck,turnkey switchto the"START" position;[ if unit is
equippedwith 12volt system] releasewhenenginebeginsto run.
• ForunitsNOT equippedwith electricstartturnkeyto "ON" positionandpull starter
Ropeuntil enginestarts.
• Setengineidle atdesiredRPM.
BREAKING IN YOUR MOWER
• Setvehicleparkingbrakeor chockwheelsto preventaccidentalrolling.
• Startengineproperly.
• Slowly, engagebladecontrol.
• In asafeenvironment,i.e.nochildren,allowbladesto rotateandengineto idle for 5
minutes.Thisbreaksin thebeltsandtheengine.
• Stopmowerproperly.
I& CAUTION! 1
SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM
SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS TO THE MOWER.
MOWER HEIGHT ADJUSTMENT
• Adjust while mower is not running.
• The cutting range is approximately 1.5" to 4.5". The height has been measured from the
ground to the blade tip without the engine running.
• Rotate height adjust crank handles (HTN) in a clockwise direction to lift the mower deck.
A counter-clockwise direction is used to lower the mower deck.
• Make sure the height adjustment is the same at side crank handles. For best results, see
"SUGGESTED PRACTICE" section. Graduated scales are for reference only, not the
actual cutter height.
• Place crank handle in a retracted position to maintain height adjustment.
STARTING TO MOW
• Adjust the cutting height.
• Double check vehicle to mower attachment.
• Start mower engine properly.
• Slowly, activate the blade engage lever (6008) by rotating it forward and left until the
lever locks into place.
• Carefully mount tow vehicle and start mowing slowly.
ALTERNATIVE STOPPINGMETHOD
•Bring vehicle to complete stop, shut off engine, and set parking brake.
• Disengage blade engage lever (6008).
• Manually shut toggle and key switches to their "OFF" positions.
• Always remember to remove keys to avoid irresponsible usage.
TRANSPORTING MOWER
• Stop mower properly.
• Place mower deck in its highest position.
• If transporting unattached from tow vehicle, then remove spark plug wire and
place where it cannot contact the spark plug.
SUGGESTED MOWING PRACTICES
• Operate mower engine at full throttle to assure the best cutting performance and
maximum material discharge.
• Allow wet grass to dry. Clumps of wet grass will collect under the mowing deck.
• Mowing should be started with tow vehicle in low gear and increased only as safe
mowing conditions permit. This speed should not exceed 5 MPH.
• The average lawn should be cut to approximately 2.5" during the cool season and
to over 3" during the hot months.
• For a healthier lawn and better aesthetics, your lawn should be mowed often and
after moderate growth.
• When cutting high or dense grass areas go slowly. Some areas may need to be
mowed twice. The second cut should be at 90 degrees to the first, if possible.
• Mowing thick or high grass. Raise rear height crank handles to .5"-.75" above
the other two handles.
• Creating a manicured lawn. Lower rear height crank handle to .25"-.5" below
front of deck. This allows grass blades to be cut twice. It also continually cuts
clippings to produce a mulching effect.
GENERAL TROUBLE SHOOTING
• The mower is not cutting level.
oLevel deck, making sure the side crank-handles are equal.
oCheck air pressure of all tires; make sure they are equal, and to
manufactures specifications.
oExamine blades for damage, while mower engine is not running.
• The engine will not start.
oDisengage blades, turn toggle switch to "ON" position, check battery and
all other electrical connections, and inspect spark plug and wire.
oCheck for fuel in the engine.
• Engine runs poorly.
oSee engine manual.
oCheck throttle adjuster.
oReplace fuel, clean fuel filter and fuel line.
IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE
MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU ARE
NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER PROBLEMS.
MOWER MAINTENANCE
GENERAL RECOMMENDATIONS
The warranty on this Trailmower does not cover items that have been subjected to operator abuse or negligence.
To receive lull value from the warranty, operator must maintain unit as instructed in this manual.
Some adjustments will need to be made periodically to maintain your unit properly.
All adjustments in this manual should be checked at least once each season.
BEFORE EACH USE
• Check engine oil level on a level surface. (Check twice to insure an accurate reading.)
• Check condition of air filter; clean and replace as necessary.
• Check blade operation; keep blades in good condition.
• Check for loose fasteners and tighten them as needed.
AFTER EACH USE
• Keep blades sharp.
• Remove fresh grass clippings with garden hose.
• Grass clippings can harden to the underside should be scraped out with a putty knife.
• Keep fluids at proper levels.
• Cover unit to prevent rain or other debris build-up. Definitely cover the engine.
BEFORE AND/OR AFTER EACH SEASON
• Replace the spark plug.
• Clean or replace the air filter.
• A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and
last longer.
• Check blades and belts for wear. Replace as necessary.
STORAGE RECOMMENDATIONS
,_ItCAUTION! Do not store engine indoors or other poorly ventilated area. Keep engine away from gas
appliances where fumes could contact open flame, pilot lights, or sparks.
,,If engine is to be stored for 30 or more days, prepare unit as follows:
• Drain fuel outside into an approved container.
• Start engine properly and run until unit is out of fuel.
• Let engine cool.
• Remove remaining gasoline from carburetor and fuel tank to prevent gum deposits from forming
within the engine. Gum deposits can cause malfunction in the engine.
• Store mower with blades disengaged to prevent belts from being permanently stretched.
BLADE CARE AND SERVICE
For best results cutter blades must be kept sharp. The blades can be sharpened with a few strokes of a file or
grinding wheel. Do not attempt to sharpen blades while they are on the cutter. Disconnect sparkplug wire
before servicing unit.
Important: Replace blades that have been damaged or deeply nicked.
Important: Check blade and spindle hardware on a regular basis to make sure nuts are tight.
I_ Only a qualified mechanic should be used for any 1
adjustments, disassembly or other kind of repairs. J
10
Detail
19
14 H10
15 12513*
16 B98
17 NB126
18 6034
19 H7N
20 H7N1TK
21 NB276
22 H7K
23 ES214
24 NB 149
25 NB 178
26 10038
NS OD41
EX:6014TC
Description
Swivel Hitch
Frame
Bearing
Cotter Pin
Rear Axle
Height Adjustment Handle
Housing Tube
5/16 PAL Nut
Plastic Knob
Crank Arm
5/8 IDX 10D 14 Ga Washer
5/8 IDX10D 10 Ga Washer
Eye Bolt
Height Indicator Decal
USE PAINT CODE: TC=R_), TK=BLACK
tem No, Description Part #
1 Tongue Hitch 66!*
2 Solid Stock Hitch 661A*
3 Bushing 10579
4 Safety Hitch Pin H11
5 Caster/Wheel Assembly 6774*
6 3/4 - 16 Nyloc Nut NB122
7 Caster Fork 665TC
8 Was her NB 195
9 Wheel Spacer 663L
10 5/8- !1 2 Way Lock Nut NB595
11 Wheel/Tire/Bearing F4157W
12 5/8 - ! 1 X 7 Bolt
13 Extension Hitch
Outer Blade
Driver
2onfiguration
Center Blade
Driver
Configuration
Item No. Description Part #
1 Center Shaft 9054
2 Blade Bearing B98
3 Bearing Housing 9057TK
4 Pulley Spacer 6065PM
5 Blade Mount P)ate 9008
6 20 I/2 "Blade 9004
7 Blade Pulley- 5.5" 6114
9 SP Washer Belly1. PLN .413 X .945 X .118 NB-607
10 3/4 ID X 1 1/40D I8 GA Washer NB-179
11 3/4-16 Jam Nut NB-175
12 3/8-24 X 1 I/4 HCC GR5 ZP NB-238
13 3/8-24 X 1 Engine Bolt Locktite NB-238N
14 1/4-20 X I"- Bolt NB-250
15 I/4-20 Serr.Flange Nut NB-524
16 3/8-24 2-Way Lock Nut NB-216
17 Housing Blade Bearing Short B99EC
18 L&R Shaft 9076
19 Bellevilte Washer AS 155
20 Fiat Washer B98W
Recommended Torque Specifications
item No Torque (ft-lbs)
11 90
I3 35
15 20
16 35 11
MOWER DECK DETAIL
Description
Belt Cover
Grass Chute
Chute Bracket
Anti-Scalp Roller
Deck
Chute Spring
Gas Cap
Gas Tank
Tank Bracket
Hitch Pin
Tank Stand
Sway Bar Left
Sway Bar Right
Deck Idler
3/8 - 16 X1 1/4 Bolt
Spacer
Idler Arm
Bushing
3/8 - 16 Nyloc Nut
Idler Pulley
3/8- 16 2 Way Lock Nut
3/8 Washer
5/16 - 18 Nyloc Nut
5/16 - 18 Eye Bolt
Spring
5/16 - 18 Nut
5/16 - 18 X 1 Bolt
3/8 - 16 X1 1/2 Bolt
5/16 - 18 Serr Flange Nut
Battery Box
Bolt/Nut for Battery Box
*USE PAINT CODE: TC=RED, TK = BLACK
Part#
6025TK
6039TK
6O30TK
AS001
6027*
9100
6102NC
6102T
6078TK
Hll
6044TK
3665
3664
6055
NB618
6040
6054TK
6037
NB182
B527
NB280
NB272
NB181
NB315
TZ2.S
NB173
NB501
NB107
NB170
6112TK
NB154Z/NB180
EX: 6060TC, 6060TK
GAS TANK ASSEMBLY
ELNIT MODELTANK ASSEMBLY
PART#
-- POL14560B
POL14560C
RK1360
T13560
T13560B1
T1360T
T17560
-- T1360B1
#6059H-- T1360H
"-12 #6080 T1360K
BELT TENSION
IDLER DETAIL
BELT CONFIGURATION
5058 (Long) 6046
(Short)
12
Slide plastic tube snug
against toggle switch.
MOTOR BASE DETAIL
HEAT SHIELD 6052TK
NOT USED ON HONDA
U_NITS DETAIL
@
SEE IDLEr
DETAIL
MOTOR BASE DETAIL
Item No Description Part #
1 Heat Shield 6052TK
2 Throttle 686N
3 Toggle Switch 685SP
4 Control Console 10737*
5 Ignition Switch 3623
6 Base - Motor, Painted 6003*
7 Belt Guide 6066
8 Belt Guide 6000
9 Top Idler Assembly 10735
10 5/16 - 18 Nyloc Nut NB181
11 Plastic Knob B19BLACK
12 Engage Lever 10727TK
13 Engage Rod Assembly 4422110636YZ
14 3/8 - 16 X 1 1/2 Bolt NB107
15 Washer NB272
16 Idler Pulley B527
17 3/8 - 16 2 Way Lock Nut NB280
18 Top Idler Weldment 6009TK
19 5/16 - 18 X 1 Bolt NB501
20 Safety Tether H9C
21 Return Spring T2SM
22 Nut - Jam 5/16-18 ZY NB173
23 Washer - SAE 5116 ZY NB275
24 Nut - Serrated Flange 5/16-18 ZY NB170
25 Nut - Flange, 1/4-20 NB524
26 Nut - HX 1/4-20 ZY NB139
27 Bolt - Serr Flng, 5/16-18 X3/4 NB596
28 Nut - Jam Lock, 1/2-13 2-Way NB121
29 Pivot - Engage 4578TK
30 Bolt - HCC 1/4-20 X 1 GR5 ZY NBI02
31 Bolt - 1/4-20 X3/4 GR5 ZY NB250
32 Screw- Phil Truss 8-32 X 1/2 ZY NB197
33 Nut - Kep 8-32 ZY NB201
34 Nut - Key Switch 9087
35 Bolt - Shoulder, 1/2 X 1-9/16 NB220
36 Nut - Nyioc 3/8-16 ZY NB182
PARTS NOT SHOWN
WiRiNG HARNESS [BRIGGS] WHN60B2
BAqq-ERY [ U 1 R ] NA
BAKERY CABLE- RED BCSR
BAKERY CABLE- BLACK BCLB
SOLENOID 9043
BATTERY STRAP BHOLD
KEYS KSK
BAKERY CABLE BOOTS BCBT
* USEPAINTCODE:TC=RED, TK=BLACK EX:6003TK
13
ENGINE DETAIL
BRIGGS /TECUMSEH > DETAIL- 1
12
DETAIL- l
Item No. Description
I UPPER SPACER
2 5-1/2" ENGINE PULLY
3 1/4/X 1" KEY STOCK
4 LOWER SPACER
5 3/6 BELLEVILLE WASHER
6 FLAT WASHER
7 3/6-24 X 1BOLT [BRIGGS ]
7/16-20 X 1 BLOT [TECUMSEH ]
8 5/16-16 X I-3/4 BOLT
9 5/16u .........................................
....................................................................................................................................
11 BELT GUIDE
..........................................................5!!6-!8 X 1 1/4 FLG.BOL
13 5/16-18 NYLOCK NUT
........_gi% .......
............._o_
4 1 ENGINE DETAIL
KOHLER > DETAIL - 2
11 DETAIL - 2
Item No. Description
I4 sP WASHER BELLVL. PLN.
I5 M8-I.25 X25 FLG BOLT
I6 M8-I.25 X55 ZP. BOLT
ENGINE DETAIL HONDA>DETAIL-3 15_
14
DETAIL - 3
Description
5/16-24 X 1" BOLT
5/16-18 NYLOCK NUT
5/16-24 x 1-1/2" BOLT
14
WIRING SCHEMATICS
HONDA 12V
BATTERY
RED
RECTIFIER
RED
PLUGS
LARGE
RED
rHONDA
SOLENOID RED 5; AMP
The Honda
_: FUSE
_i_o the starter GREEN
i
t and comes w_h t
Ct_heengine. _ '
JIGIIITIOH
_&ITCH
TOGGLE
!
BLACK
TECUMSEH 12V
BATTERY LARGE
RED
SOLENOID RED 5AMP
FUSE
GREEN
IGI|ITIOII
TOGGLE
TCH BLACK DE HR_|
!WHITE
KOHLER 12V
BATTERY
i
SOLEHOID
TOGGLE
LARGE
RED
RED %
LARGE
RED
RED
GREEH
WHN6OB2
15
www.swisherinc.com
OWNER'S
MANUAL
MODEL NO.
T1360B1
T1360T
T1360H
T1360K
T13560
RK1360
T14560
T17560
T18560
f
60" FINISH CUT
TRAILMOWER
HOW TO ORDER
REPAIR PARTS:
Each mower has its own model number. Each engine has its
own model number. The model number for the mower will be
f\mnd on the right hand side of the fiame at the wheel bracket.
The model number f\3rthe engine will be found on the top of
the blower tan housing.
All mower parts listed herein may be ordered directly from
Swisher Mower & Machine Co. Inc. or your nearest Swisher
dealer.
All engine parts may be ordered fiom the nearest dealer of the
engine supplied with your mower.
Color cannot be guaranteed on service parts.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT T-60 TRAILMOWER
* SERIAL NUMBER -
* MODEL NUMBER -
* ENGINE MODEL NUMBER -
TYPE -
* PART NUMBER
* PART DESCRIPTION
TELEPHONE- 1-800-222-8183
FAX- 1-660-747-8650
SWISHER MOWER &MACHINE CO. INC.
1602 CORPORATE DRIVE
_._. WARRENSBURG, MO 64093 ..J
SWISHER MOWER & MACHINE CO. INC.
