SZ DJI TECHNOLOGY 60TX1604 SRW-60G User Manual Rev
SZ DJI TECHNOLOGY CO., LTD SRW-60G Rev
User Manual Rev
DJI SRW-60G User Manual 2016.06 V1.0 Disclaimer and Warning Congratulations on purchasing your new DJITM product. The information in this document affects your safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper coniguration before use. Failure to read and follow instructions and warnings in this document may result in serious injury to yourself or others, or damage to your DJI product or damage to other objects in the vicinity. This User Manual and all other collateral documents are subject to change at the sole discretion of DJI. For up-to-date product information, visit http://www.dji.com and click on the product page for this product. By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand and agree to abide by the terms and conditions herein. You agree that you are solely responsible for your own conduct while using this product, and for any consequences thereof. You agree to use this product only for purposes that are proper and in accordance with all applicable laws, rules, and regulations, and all terms, precautions, practices, policies and guidelines DJI has made and may make available. DJI accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly from the use of this product. The user shall observe safe and lawful practices including, but not limited to, those set forth in this User Manual. DJI is a trademark of SZ DJI Technology Co., Ltd. (abbreviated as “DJI”) and its ailiated companies. Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies. Using this Manual Legend WARNING CAUTION NOTICE TIPS Warning: Failure to properly follow procedures may result in property damage, collateral damage, and serious or supericial injury. Caution: Failure to properly follow procedures may result in property damage and serious injury. Notice: Failure to properly follow procedures may result in property damage, a small possiblity of injury, or no possibility of injury. Tips © 2016 DJI All Rights Reserved. Before You Begin Make sure all the parts listed in the In the Box section below are included in the package. Read this entire User Manual and watch the informational and tutorial videos on the product page of DJI’s oicial website (http://www.dji.com). Read the disclaimers and warnings above to understand your legal rights and responsibilities. If you have any questions or problems during the installation, maintenance or use of this product, please contact DJI or a DJI authorized dealer. In the Box Transmitter ×1 Receiver ×1 Power Cable for Transmitter ×1 Power Cable for Receiver ×1 USB Cable ×2 Screw (M3×5.5) ×4 Introduction The DJI SRW-60G is a short range wireless video link, which can transmit real time HD video or images for up to 10 meters. Containing both a transmitter and a receiver, it can also be used with the Ronin series of handheld gimbals. Convenient video transmission in a meeting room or at home are also a breeze with the SRW-60G. © 2016 DJI All Rights Reserved. SRW-60G Diagram Transmitter 1. HDMI Port For connecting to the HDMI output for HDMI transmission. 2. Gimbal Mounting Adapter For mounting to a Ronin-MX or Ronin-M. The adapter can be removed when not used with the Ronin-MX or Ronin-M. 3. Cable Slot For fastening the cable in position. 4. Link Button For linking to the Receiver. 6. Power Port For power supply. 5. Micro USB Port For irmware upgrades and power supply. 7. Status LED Indicates the communication status with the Receiver. Receiver 1. Micro USB Port For irmware upgrades and power supply. 2. Power Port For power supply. 3. HDMI Port For connecting to HDMI input for HDMI transmission. 4. Mounting Adapter The adapter can be removed. © 2016 DJI All Rights Reserved. 5. Status LED Indicates the communication status with the Transmitter. Usage Using the SRW-60G with a Ronin Series Gimbal 1. Loosen the screw of the clamp on the gimbal mounting adapter of the Transmitter. Then attach the Transmitter to the arm of the Ronin-MX or Ronin-M and tighten the screw. 2. Link the HDMI Ports of the Transmitter and the camera by using a soft and lexible HDMI cable (not provided). 3. Connect the Power Port on the Transmitter to the CAN1 Port (or the USB port) of the Ronin-MX by using the provided transmitter power cable. CAN1 Port USB Port NOTICE In order to avoid obstructing any gimbal movements, the cables can be attached in the cable slot. © 2016 DJI All Rights Reserved. 4. If using a Ronin, remove the gimbal mounting adapter and stick the Transmitter onto the Ronin or your camera. Antenna Position 5. Remove the mounting adapter and mount the Receiver in place. Antenna Position NOTICE Ensure both the Transmitter and Receiver are not obstructed during use. Using the SRW-60G in a Meeting Room or at Home 1. Remove the mounting adapters. 2. Connect the HDMI output and input to the Transmitter and Receiver separately. 3. Connect the USB ports on both the Transmitter and Receiver to an external power supply. NOTICE The USB port operation voltage is 5 V (DC). © 2016 DJI All Rights Reserved. Linking The Transmitter is linked to the Receiver before delivery. Linking is only required when using a new Transmitter or Receiver. Ensure the Transmitter and Receiver are properly connected to the HDMI device before linking to avoid failure. How to link Press the Link button on the Transmitter once. The linking process will complete in approximately 10 seconds. Status LED Descriptions Transmitter Status LED Receiver Status LED ...... Blinks red ...... Blinks green slowly slowly Blinks red ...... ...... Blinks green quickly quickly Blinks green ...... ...... Blinks green quickly quickly — TIPS Solid green — Solid green Description The device is not linked and not connected to the HDMI device. Linking but the Transmitter is not connected to the HDMI device. Linking in progress Linking successful and working normally If the linking process does not complete after 15 seconds, check the HDMI connection on both the Transmitter and Receiver. © 2016 DJI All Rights Reserved. Speciications General Max Transmission Distance 10 m (unobstructed) Max Transmitter Power (EIRP) Transmitter: 17 dBm, Receiver: 30 dBm Receiver Sensitivity -72 dBm Operating Frequency 57 GHz to 64 GHz Video Output Port HDMI Video Resolution From 480 i / 576 i to 1080p 60Hz Latency < 1 ms Transmitter Dimensions 78 mm (L) × 33 mm (W) × 16 mm (H) Weight 46 g Antenna Gain LRP Mode: 5 dBi; MRP Mode: 9 dBi Operating Voltage (DC) 7.4-12 V (CAN Port) or 5 V (USB Port) Max Consumption 1.5 W Operating Temperature 32° to 104° F (0° to 40° C) Antenna Type Built-in Antenna Receiver Dimensions 65 mm (L) × 46 mm (W) × 14 mm (H) Weight 47 g Antenna Gain 16 dBi Operating Voltage (DC) 7.4-18 V (CAN Port) or 5 V (USB Port) Max Consumption 2.5 W Operating Temperature 32° to 104° F (0° to 40° C) Antenna Type Built-in Antenna © 2016 DJI All Rights Reserved. FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. IC RSS Warning This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. © 2016 DJI All Rights Reserved. IC Radiation Exposure Statement: This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. KCC Warning Message “해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .” “해당 무선설비는 운용 중 전파혼신 가능성이 있음” EU Compliance Statement SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany 10 © 2016 DJI All Rights Reserved. DJI Support http://www.dji.com/support The content is subject to change. Download the latest version from http://www.dji.com/product/ronin-mx If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. RONINTM is a trademark of DJI. Copyright © 2016 DJI All Rights Reserved. Printed in China. © 2016 DJI All Rights Reserved. 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2016:09:22 15:07:18+08:00 Creator : Adobe InDesign CC (Macintosh) Modify Date : 2016:10:05 17:57:48-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2016:10:05 17:57:48-07:00 Creator Tool : Adobe InDesign CC (Macintosh) Instance ID : uuid:f7a93fc7-a37d-454a-a750-59ed65007158 Original Document ID : xmp.did:76d5adc3-bba9-40e8-9c51-97e7422a4e8b Document ID : xmp.id:d994639f-d38f-4188-90ee-4a7c48d74e8d Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:fb7e3f40-5a93-496f-b5d4-dc789cb2e9ce Derived From Document ID : xmp.did:a7ff4aa0-38fa-4132-822b-5c1700389d69 Derived From Original Document ID: xmp.did:76d5adc3-bba9-40e8-9c51-97e7422a4e8b Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC (Macintosh) History Changed : / History When : 2016:09:22 15:07:18+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 11EXIF Metadata provided by EXIF.tools