SZ DJI TECHNOLOGY G1P1709 DJI Goggles Racing Edition User Manual DJI Goggles RE QSG

Download:
Mirror Download [FCC.gov]
Document ID	3632756
Application ID	jzz6cT0t8fbbEDvlewJ8RQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	54.82kB (685298 bits)
Date Submitted	2017-11-08 00:00:00
Date Available	2018-05-07 00:00:00
Creation Date	2017-10-18 18:14:07
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2017-11-07 17:00:36
Document Title	Microsoft Word - DJI Goggles RE QSG
Document Creator	PScript5.dll Version 5.2
Document Author:	DG06139

DJI GOGGLES
Racing Edition
Quick Start Guide
V1.0
DJI Goggles Racing Edition
DJI Goggles Racing Edition (hereafter abbreviated as “DJI Goggles”)are equipped
with high-performance displays and an ultra-low latency video downlink for use
with DJITM aircraft, giving you a real-time aerial First Person View (FPV) experience.
DJI Goggles can also be used to display HD videos, bringing you an immersive
high-definition viewing experience. DJI Goggles support head tracking, allowing
aircraft and gimbal to be controlled using head movements, introducing a new
style of flying.*
The
DJI
Goggles
Racing
Editionfeatures
the
advanced
OCUSYNCTMvideo
transmission, supporting both theAnalog Video Downlink and 2.4 / 5.8GHz
dual-band Digital Video Downlink, providing a high video downlink performance
with as low as 50ms latency and up to 2km transmission distance, a variety of
Antennas can be usedfor more application scenarios. For third-party racing aircraft,
DJI OcuSync Air Unit can be used directly with DJI Goggles to provide you with
acamera, video transmission, controls and displays integrated, high-quality racing
flight experience.
1. Touch Panel
2. Headband
3. Charging Status Indicator
4. Micro USB Port
5. Headband Knob
6. Speaker
7. Power Button
8. Battery Level Indicators
9. Back Button
10. Function Button
11. Link Button
12. Linking Status Indicator
13. IPD (Interpupillary
Distance) Knob
14. Lens
15. Proximity Sensor
16. Headband Buckle
17. Heat Vent
18. Micro SD Card Slot
19. 3.5 mm Audio Port
20. HDMI Type-D Port
21. Speaker
22. SMAAntenna Port
1. Camera Port
Connect with the DJI OcuSync Camera. Note
that both this port and the camera connector
plug are customize Type-C interface and they
are not compatible with third-party equipment.
2. SBUS Port
Connect with the 3 in 1 Cable(power, S.Bus,
UART), and connect to power, flight controller
and the OSD port based on the sequence
below.
RED: Power
BLACK: Power GND
GRAY: UART RX(Connects toOSD)
WHITE: UART TX (Connects toOSD)
BROWN: GND
YELLOW: SBUS(Connects toFlight Controller
RX)
3. Micro SDCard Slot
Insert Micro SD Card to store the video
recorded.
4. Antenna Ports
Used to attach the Air Unit antennas.
5.
Micro USB Port
Connects to your PC for firmware
upgradesthrough the DJI Assistant 2.
6. PPM Port
Connects to the aircraft’s gimbal with the
PPM Cable to control the aircraft or gimbal by
DJI Goggles. (supported later)
7. Link Button
Press this button to link the DJI OcuSync Air
Unit with the DJI Goggles.
8. Linking Status Indicator
Indicate the linking status of the DJI OcuSync
Air Unit and the DJI Goggles.
Module Connections
Analog Video Downlink
Install the pagoda antenna (SMA interface) to the SMA Port of DJI Goggles directly.
The provided pagoda antenna (SMA interface) also support two-way
digital transmission.A directional antenna with higher gain can be used
for better analogue transmission performance,.
Digital Video Downlink
When using the Digital Video Downlink, In addition to install the pagoda antenna
(SMA interface) to the SMA Port of DJI Goggles, you will also need to install the DJI
OcuSync Air System on a third-party racing aircraft to work with DJI Goggles. Refer
to the below connection illustration and then mount the modules onto the aircraft.
z
It is recommended to use a lighter dipole antennawithin a short
distance flight, while a pagoda antenna (SMA interface) or a
cylindrical antenna is recommended when the flight distance is 100 m
or more.
It is recommended to mount the DJI OcuSync Air Unit with its screw
side facing down.
The SBUS Port and the PPM Port on the Air Unit are only used when
transmitting the remote control signal, these ports are not need to be
connected if only video downlink is used.
Place the two antennas on the Air Unit in a mutually vertical manner
and with at least 30mm apart. Note that avoidinggood conductor
block at the antenna level, and keep the bottom of the antennafrom
the good conductor (cable, carbon fiber frame, battery and metal,
etc.) at least 25mm.
You can connect the coach port of a third-party remote controllerand the audio
port onDJI Gogglesthrough the coach cable to transmit the control signal to the
racing aircraft when using the Digital Video Downlink
Installation and Wearing
Check the Battery Level and Charging
Press once to check the battery level.
Press once, then again and hold to turn on/off.
The Battery is fully charged when the Charging Status Indicator or the BatteryLevel
Indicators turn off.
Charge time: ~ 4 hours Maximum run-time: ~ 6 hours
Activation and Connection
First-time activation is required before using your new DJI Goggles.
Ensure all devices are powered on and that the Aircraft is linked with the Remote
Controller. Make sure both are updated to the latest firmware versions.
MAVICTMSeries
INSPIRETM 2
INSPIRESeries
Video Play
PHANTOMTM 4
PHANTOM 4 PRO+
Device
Series
PHANTOM 4 ADVANCED+
SPARKTM**
OCUSYNCTM
Micro USB cable
Press the Link
* Prepare an OTG
Buttons on the
cable and connect it
Mavic Pro and DJI
to the Micro USB port
Goggles, or enter
of the remote
Tools > Setting >
controller.
HDMI cable
HDMI cable
Live view only.
Linking Setting
toconnect.
Follow the steps below to link with the third-party racing aircraft.
1. Power on the DJI OcuSync Air Unit, press the link button on the air unit with an
appropriate tool when the linking status indicator is solid green, the indicator
will turn solid red when the air unit is waiting for linking.
2. Power on the DJI Goggles, directly press the link button with an appropriate
tool in the main menu, or swipe downward with two fingers on the touch panel
to enter the shortcut menu and select RacingDrone (Digital)> Linking Settings.
3. Make sure the distance between DJI Goggles and the Air Unit is within 2m, both
the two linking status indicators will turn solid green when successfully linked,
and the video will be normally displayed.
Controls
Single Finger Touch /
Two Fingers Touch
Somatic Control
5D Button*
● Swipe forward/backward to
DJI Goggles support
Swipe to scroll on
unlock/ lock the touch panel
head tracking,
the menu
● Swipe upward/downward to
allowing aircraft and
Tap to confirm
exit/enter the shortcut menu
gimbal to be
controlled using head
movements. Multi
Intelligent Flight
Modes are also
supported.
Back Button / C2
Function Button / C1 Button*
Only support:
Button*
Press to show the focus cursor,
MAVIC Series
Press to return to the
swipe forward/backward with
Spark
previous menu, or exit
one finger to zoom in or zoom
Phantom 4 Series
the current Intelligent
out. Move your head then tap the
Inspire 2
Flight Mode.
touch panel to define the focus
point.
* When connected with Mavic series aircraft, the 5D, C1, and C2
buttons on the remote controller will be used to control the DJI
Goggles and their original function is disabled.
Specifications
Model
DJI Goggles:G1P；DJI OcuSync Air Unit:OAS1
Weight (Typical)
DJI Goggles Body: 495 g
Headband: 500 g
Dimensions
Lenses: 195×155×110 mm
Strap(Folded): 255×205×92 mm
Screen Size
5 inch×2
Screen Resolution
3840 × 1080 (single screen: 1920 × 1080)
Communication Frequency
2.4GHz/ 5.8GHz
Transmitter Power (EIRP)
DJI Goggles
2.4 GHz: 34 dBm (FCC); 19 dBm (CE); 19 dBm (SRRC)
5.8 GHz: 29 dBm (FCC); 13 dBm (CE); 19 dBm (SRRC)
DJI OcuSync Air Unit
2.4 GHz: 26 dBm (FCC); 19 dBm (CE); 19 dBm (SRRC)
5.8 GHz: 26 dBm (FCC); 13 dBm (CE); 23 dBm (SRRC)
Live View Modes
1080p30，960p50，720p60，480p50
Battery Capacity
9440 mAh
Operating Temperature Range
32° to 104° F (0° to 40° C)
Charger
Input: 100-240 VAC, 50 / 60 Hz, 0.5 A
Output:
Compliance Information
FCC Regulatory Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Notice:
This equipment has been tested and found to comply with th e limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interferencein a residential installation. This
equipment g enerates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the in structions , may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RSS Regulatory Statement
This device complies with ISEDC license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this devi ce must a ccept any interfer ence, in cluding inter ference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISDEC applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même sile
brouillage est susceptible d'en compromettre le fonctionnement.
SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the
goggles transmitting at its highest certified power level in all tested frequency bands, although
the SAR is determined at the highest certified power level, the actual SAR level of the goggles
while operating can be well below the maximum value.
Before a new model goggles is a available for sale to the public, it must be tested and certified to
the FCC/ISEDC that it does not exceed the exposure limit established by the FCC/ISEDC, Tests for each
goggles are performed in positions and locations (e.g. at the ear and worn on the body)as
required by the FCC/ISEDC.
For body worn operation, this model goggles has been tested and meets the FCC/ISEDC RF exposure
guidelines when used with an accessory designated for this product or when used with an accessory that
Contains no metal.
Non-compliance with the above restrictions may result in violation of RF exposure guidelines.
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this
device is in compliance with the essential requirements and other relevant provisions of
the RED Directive.
A copy of the EU Declaration of Conformity is available online at
www.dji.com/euro-compliance
DeclaraciónGHFXPSOLPLHQWR8( SZ DJI TECHNOLOGY CO., LTD. por la
presentedeclara que este dispositivo cumple los requisitos básicos y el resto de
provisionesrelevantes de la Directiva.
Hay disponible online una copia de la Declaración de conformidad UE en
www.dji.com/euro-compliance
EU-verklaring van overeenstemming: SZ DJI TECHNOL OGY CO., LTD. verk laart
hierbijdat dit apparaat voldoet aan de essentiële vereisten en andere relevante
bepalingen vanRichtlijn.
De EU-verklaring van overeenstemming is online beschikbaar op
www.dji.com/euro-compliance
Declaração de conformidade da UE: A SZ DJI TECHNOLOGY CO., LTD. declara,
atravésdeste documento, que este dispositivo está em conformidade com os requisites
essenciais e outras disposições relevantes da Diretiva.
Existe uma cópia da Declaração de conformidade da UE disponível online em
www.dji.com/euro-compliance
Dichiarazione di conformità UE: SZ DJI TECHNOLOGY CO., L TD. dichiara che il
presentedispositivo è conforme ai requisiti essenziali e alle altre disposizioni rilevanti
delladirettiva.
Una copia della dichiarazione di conformità UE è disponibile online all'indirizzo
Webwww.dji.com/euro-compliance
Déclaration de conformité UE: Par la présente, SZ DJI TECHNOLOGY CO., LTD
declare que cet appareil est conforme aux principales exigences et autres clauses
pertinentesde la directive européenne.
Une copie de la déclaration de conformité UE est disponible sur le site
www.dji.com/euro-compliance
EU-Compliance: Hiermit erklärt SZ DJI TECHNOLOGY CO., LTD., dass dieses Gerätden
wesentlichen Anforderungen und anderen einschlägigen Bestimmungen der EURichtlinie
entspricht. Eine Kopie der EU-Konformitätserklärung finden Sie online
aufwww.dji.com/euro-compliance.
EU contact address: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany.
Environmentally friendly disposal
Old electrical appliance must not be disposed of together with the residual waste,
but have to be deposed of separately. The disposal at the communal collection point
via private person is for free. The owner of old appliance is responsible to bring the
appliances to these collecting point or to similar collection points. With this little personal
effort, you contribute to recycle valuable raw materials and the treatment of toxic
substances.
KCC Warning Statement
(1)
이기기는가정용으로전자파적합등록을한기기로서주거지역에서는물론모든지역에서
사용할수있습니다.
(2) 당해무선설비는전파혼신가능성이있으므로인명안전과관련된서비스는할수없음。
NCC Warning Statement
根據 NCC 低功率電波輻射性電機管理辦法規定:
(1) 第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅
自變更頻率、加大功率或變更原設計之特性及功能。
(2) 第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象
時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
NBTC Warning Statement
เครื่องโทรคมนาคมและอุปกรณนี้มีความสอดคลองตามขอกําหนดของกทช.
IFETELWarning Statement
“La operación de este equipo está sujeta a la s siguientes dos condiciones: (1) es posible
que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o
dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada.”

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : DG06139
Create Date                     : 2017:10:18 18:14:07+08:00
Modify Date                     : 2017:11:07 17:00:36-08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2017:11:07 17:00:36-08:00
Format                          : application/pdf
Title                           : Microsoft Word - DJI Goggles RE QSG
Creator                         : DG06139
Document ID                     : uuid:501b8842-6ff8-4e0c-8b24-52ac19594695
Instance ID                     : uuid:2e3ecc3d-981b-4f6e-a3fe-469eae916b02
Page Count                      : 16

EXIF Metadata provided by EXIF.tools