SZ DJI TECHNOLOGY GL200A1606 C2 User Manual user manaulx

SZ DJI TECHNOLOGY CO., LTD C2 user manaulx

Users Manual

Download: SZ DJI TECHNOLOGY GL200A1606 C2 User Manual user manaulx
Mirror Download [FCC.gov]SZ DJI TECHNOLOGY GL200A1606 C2 User Manual user manaulx
Document ID3146204
Application IDzwljuaBMF2OUNAiLi5QZcA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize44.54kB (556761 bits)
Date Submitted2016-09-25 00:00:00
Date Available2017-03-21 00:00:00
Creation Date2017-12-15 04:16:06
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-12-15 04:16:06
Document TitleMicrosoft Word - user manaul.docx
Document CreatorPScript5.dll Version 5.2
Document Author: elena

User Manual
Setting Up Aircraft and Batteries
The arms of the aircraft is folded on its delivery. Follow the instructions below to unfold the arms of the aircraft.
Setting Up Aircraft
1.
Rotate anti‐clockwise to unfold front arms towards the nose of the aircraft.
2.
Rotate anti‐clockwise to unfold rear arms of the aircraft.
3. Unfold all propeller blades and ensure all blades are aligned.
4. Ensure the Intelligent Flight Battery securely attached to the aircraft. The Intelligent Flight
Battery must be fully charged on its first use.
Setting Up Remote Controller
Unfold the mobile holder clamps and adjust the position of the antennas.
1. Insert the mobile devices into the space between the two mobile holder clamps.
2. Push the mobile holder clamps against the mobile device to secure its position.
3.Connect your mobile device with the a USB cable. You may also connect the mobile device to
the charging port of the remote controller with the supplied multi‐purpose USB cable.
Aircraft Diagram
1.
2.
3.
4.
GPS
Obstacle Sensing System
Motor
Gimbal
5.
6.
7.
Front LED Indicator
Vision Positioning Sensors
Aircraft Status Indicator
8. Control Mode Switch
9. Camera Micro SD Card Slot
10. Linking Button
11. Camera Micro SD Card Slot
Remote Controller Diagram
[1] Antennas
Relays aircraft control and video signal.
[2] Power Button
Used to power on or off the remote controller
[3]Control Stick
Controls the orientation and movement of the aircraft.
[4] App Button
Gain quick access to the feature in the DJI GO app.
[5] Mobile Holder Clamp
Adjust its width to accommodate the mobile device.
[6] Intelligent Flight Pause Button
Press once to allow the aircraft to exit from TapFly, ActiveTrack and Advanced mode.
[7] Return Home (RTH) Button
Press and hold the button to initiate Return to Home (RTH).
[8] Remote Controller Status Screen
Display system status of the remote controller.
[9] USB Port
Connect to mobile device for running the DJI GO app.
[10] C2 Button
[11] Camera Settings Dial
Turn the dial to adjust camera settings. (Only functions when the remote controller is connected
to a mobile device running the DJI GO app. )
[12] Shutter Button
Press to take a photo. If burst mode is selected, the set number of photos will be taken with one
press.
[13] Video Recording Button
Press to start recording video. Press again to stop recording.
[14] Gimbal Dial
Use this dial to control the tilt of the gimbal.
[15] C1 Button
Press C1 button once to launch the DJI GO app on the mobile device.
[16] Lanyard Hole
Used to secure the position of your lanyard.
[17] Flight Mode Switch
Switch between P‐mode, S‐mode
[18] Charging Port
Connect to the supplied charging cable for charging the battery. Connect to the supplied
mulit‐purpose USB cable for accessing to mobile device.
Using Remote Controller
Remote controller comes with a rechargeable battery. The battery level is displayed on the
remote controller system status screen. Follow the steps below to power on the remote
controller:
1. Press once and release to check the current battery level.
2. Press and hold the Power Button to turn on the remote controller.
3. The remote controller will beep when it is turned on, in addition, the battery level is displayed
on the remote controller status screen.
4. Repeat Step 2 to turn off the remote controller.
Intelligent Flight Battery
Power on or off the Intelligent Flight Battery
Turning On: Press the Power Button once, then press again and hold for 2 seconds to turn on.
The Power LED will turn red and the remote controller system status screen will display the
current battery level.
Turning Off: Press the Power Button once, then press again and hold for 2 seconds to turn off.
Power level indicators turn off when it is power down.
Switch
Charging
1.Connect the Battery Charger to a power source (100‐240 V 50/60 Hz).
2.Connect one end of the charger to the Intelligent Flight Battery to the Battery Charger. If the
battery level is above 95%, turn on the battery before charging.
3.The Battery Level Indicator will display the current battery level as it is charging.
4.The Intelligent Flight Battery is fully charged when the Battery Level Indicators are all off.
Disconnect the Intelligent Flight Battery from the Battery Charger.
5.Air‐cool the Intelligent Flight Battery after each flight. Allow its temperature to drop to room
temperature before storing it for an extended period.
6. The charger will stop charging the battery if the battery cell’s temperature is not within the
operating range (0°C ~ 40°C ).
Powering on the Aircraft and Remote Controller
1. Unfold the front and rear arms and propellers.
2. Power on the remote controller follow by the Intelligent Flight Battery.
3. Launch the DJI GO app and enter the “Camera” view.
Starting and Stopping the Motors
Starting the Motors
Push both sticks to the bottom inner or outer corners to start the motors. Once the motors have started spinning, release both
sticks simultaneously.
Stopping the Motors
There are two methods to stop the motors. When the aircraft has landed, push the throttle down ① , then conduct the same
CSC that was used to start the motors, as described above . Motors will stop immediately. Release both sticks once the motors
stop. Method 2: When the aircraft has landed, push and hold the throttle down. The motors will stop after3
seconds.
Using Mobile Device for Aircraft Control
You may choose control the aircraft via the WiFi connection below the mobile device and the
aircraft. Follow the steps below to learn how to use the mobile devices to control your WM200
aircraft.
1. Power off the Intelligent Flight Battery then slide the Control Mode Switch to enable
controlling the aircraft through mobile device.
2. Power on the remote controller then power on the Intelligent Flight Battery.
3. Enable WiFi connection on the mobile device, select “DJI Aircraft” from WiFi network list,
and enter the default password “12341234”.
4. Launch DJI GO app from the mobile device and select “Camera” view. Connection is
established if live view from the camera is displayed on the screen.
5. Virtual control sticks are displayed on screen, use these sticks to maneuver the aircraft.
Specifications
Aircraft
Model
M1P and M1S
Weight gimbal excluded
737 g
Weight gimbal included
746 g
Max Ascent Speed
5 m/s
Max Descent Speed
3 m/s
Max Speed
18 m/s
19685 feet ( 6000 m ) ( Software altitude limit: 400
Max Service Ceiling Above
feet above take‐off point )
Sea Level
Max Flight Time
Approx. 25 minutes
Operating
Range
32° to 104° F ( 0° to 40° C )
Temperature
Satellite Systems
GPS/GLONASS
Gimbal
Controllable Range
Pitch: ‐ 90° to + 30°
Obstacle Sensing System
Obstacle Sensory Range
2 ‐ 49 feet ( 0.7 ‐ 15 m )
Operating Environment
Surface with clear pattern and adequate lighting ( lux > 15 )
Vision Positioning System
Altitude Range
Velocity Range ≤10 m/s ( 2 m above ground )
Altitude Range
0.3 meter ‐ 10 meter (0 ‐ 33 feet)
Operating Range
0.3 meter ‐ 10 meter (0 ‐ 33 feet)
Operating Environment
Surface with clear pattern and adequate lighting ( lux > 15 )
Camera
Sensor
1/2.3” Effective pixels:12 M
Lens
FOV ( Field Of View ) 94° 20 mm ( 35 mm format equivalent ) f/2.8
focus at ∞
ISO Range
100‐3200(video) 100‐1600(photo)
Electronic Shutter Speed
1/8 ‐ 1/8000S
Max Image Size
4000×3000
Still Photography Mode
ingle shot
Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB)
Time‐lapse
HDR
Video Recording Modes
3/5 Bracketed frames at 0.7EV Bias
UHD: 4096×2160 4K 24 / 25p
3840×2160 4K 24 / 25 / 30p
2704×1520 2.7K
24 / 25 / 30p
FHD: 1920×1080
24 / 25 / 30 / 48 / 50 / 60 / 120p
HD: 1280×720
24 / 25 / 30 / 48 / 50 / 60p
Max. Bitrate Of Video Storage
60 Mbps
≤ 32 GB ;exFAT
Supported File Formtas
FAT32
Photo
JPEG,DNG
Video
MP4/MOV MPEG‐4 AVC/H.264
Supported SD Card Types
Micro SD
Max capacity: 64 GB. Class 10 or UHS‐1 rating required
Operating Temperature
32° to 104° F ( 0° to 40° C )
> 32 GB
RAW
Remote Controller
Operating Frequency
2.400 ‐ 2.483 GHz
Max
Distance
FCC: 7000 m;CE: 4000 m Unobstructed, free of interference
Transmission
Operating Temperate
32° to 104° F ( 0° to 40° C )
Battery
2970 mAh
Transmitter Power EIRP
FCC:
Operating Voltage
700 mA @3.7 V
30 dBm; CE: 19.5 dBm
Charger
Voltage
13.05 V
Rated Power
50 W
Intelligent Flight Battery
Capacity
3830 mAh
Voltage
11.4 V
Battery Type
LiPo 3S
Energy
43.6 Wh
Weight
around 238 g
Operating Temperature
32° to 104° F ( 0° to 40° C )
Max Charging Power
100 W
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co‐located or operating in conjunction with any
other antenna or transmitter.
IC RSS Warning
This device complies with Industry Canada licence‐exempt RSS standard (s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference,including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co‐located or operating in conjunction with any other
antenna or transmitter.
Cet appareil est
conforme aux limitesd'exposition de rayonnement RF IC établiespour un environnement non contrôlé.
Cetémetteur ne doit pas être co‐implanté oufonctionner en conjonction avec toute autreantenne ou transmett
eur.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in
compliance with the essential requirements and other relevant provisions of the R&TTE Directive.
A copy of the EU Declaration of Conformity is available online at www.dji.com/euro‐compliance
EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : elena
Create Date                     : 2016:08:31 16:46:03+08:00
Modify Date                     : 2016:09:22 14:09:16-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2016:09:22 14:09:16-07:00
Format                          : application/pdf
Title                           : Microsoft Word - user manaul.docx
Creator                         : elena
Document ID                     : uuid:1d3ab657-09eb-40f4-97bd-d808005da762
Instance ID                     : uuid:489d003a-f661-4eb8-a6ea-8945935cdbc4
Page Count                      : 14
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SS3-GL200A1606

Navigation menu