SZ DJI TECHNOLOGY GL6581410 C1 User Manual NEW x
SZ DJI TECHNOLOGY CO., LTD C1 NEW x
Users Manual
DJI Inspire 1 User Manual Compliance Information KCC Warning Message “해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.” “해당 무선설비는 운용 중 전파혼신 가능성이 있음” In the Box Check that all of the following items have been included in your package before use. If anything is missing, please contact your local dealer. Index Name Picture Qty. DJI Inspire 1 Propeller C1 Camera with gimbal Smart Battery Battery Charger Introduction DJI Inspire 1 package includes aircraft, C1, gimbal, camera and DJI App. Flight control system is inside the aircraft, the built‐in camera has been integrated with gimbal. C1 and DJI App are used to control the aircraft, gimbal and camera. The HD video downlink and receiver have been integrated in the aircraft, which is used for HD video transmitter and control the aircraft. Features: ‐Equipped with retractable landing gear, and unobstructed 360 degree view from the camera is made possible by simply moving the landing gear out of sight. The maximum flight height of DJI Inspire 1 is **, the maximum distance is **. DJI Inspire 1 has a battery capacity of 6S, 4500mAh. When the battery is fully charged, it has a maximum run time of **. ‐ The camera is using a 21mm bugeye lens, which has low optical distortion and high resolution. Video output can be achieved at HD 4Kp30@60Mbps and it supports many kinds of filters. A high performance gimbal enables to obtain stable images even when the aircraft is fling in high speed. -Integrated the advanced flight controller of DJI, the DJI Inspire 1 has stable performance during flight. It can automatically fly back when the C1 signal was missed. The hover assistant enable the DJI Inspire 1 to hover stable without GPS. ‐ The HD video downlink has been integrated inside the aircraft, which is used with DJI App to display real time HD aerial image, aircraft data and camera data on the mobile device. In addition, it provides ground station function which allows users to plan the flight mission and enables aircraft to flight automatically. Flight safety In GPS mode, the aircraft can be positioned accurately and hover stably, and the return home function is available. (Orientation of aircraft is under control but it could not avoid obstructer automatically). Hover assistant makes aircraft hover stable without GPS (hover assistant can work properly below height of 5m, and the floor surface have pattern variations in good light conditions). Aircraft [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] GL658A [1] Antenna [2] Mounting Po osition [3] Stick [4] Neck Strap Attachment [5] RTH Button [6] Transformati ion Switch [7] Battery Leveel LEDs [8] Status LED [9] Power Button [10] Camera Setttings Dial [11] Playback Bu utton Built‐in GPS Propellerr Motor Front LE ED Landing gear Frame arrm Gimbal DJI Smarrt Battery Micro‐US SB Port Rear LED Camera Micro‐USB Port Camera Micro‐SD Card Port Hover asssistant camera [12] Shutter Button [13] Flight Mode Switch [14] Video Recording Button [15] Gimbal Dial [16] HDMI Port [17] Upgrade Port [18] CAN Port [19] USB Port [20] Handle Bar [21] Reserved Button [22] Power Source Port [23] Reserved Button Start 1. Watch the tutorial video Scan the QR code or click the link shown below to watch the tutorial video. Tutorial video http://www.dji.com/Inspire1/training 2. Download DJI App Search ʺDJI” on the App Store then follow instructions for iOS version. Search ʺDJIʺ on Google Play then follow instructions for Android version. Register your e‐mail address when using the app for the very first time. App Store Google Play 3. Ensure the smart battery\C1 and the mobile device are fully charged. Please charge the device if it has low battery level. Important: Please watch the tutorial and read the quick start guide fully before using your DJI Inspire 1. * For the best experience, install and use the DJI App on tablet. ** See Appendix for checking battery levels. Refer to user manual for charging。 DJI App There are four page of GUI: Camera, ground station, tool box and user center. [1] Present flight mode [2] GPS signal status [3] Aircraft status [4] RC settings [5] HD video downlink settings [6] Smart battery information [7] General settings [8] Photo format [9] Video format/Recording time [10] Shutter/Record switch [11] Shutter/Record [12] Play back [13] Camera settings [14] Ground station [15] Aircraft orientation/Height/Distance [16] Home point settings [17] Return home [18] Gimbal mode [19] Take off Camera GUI: For display the real time HD images and aircraft data, enable shutter and video recording. Ground Station: For display the map for setting flight mission. User Center: photograph and video synchronization, flight record, DJI Shop and account information. Preparing DJI Inspire 1 1. Mounting the Gimbal Step 1:Remove the Gimbal Cover and the Gimbal Clamp from the gimbal. Step 2:Turn the Gimbal Lock to the right (when you are facing the nose of the DJI Inspire 1) until it locks in place and you hear a clicking sound. Refer to the picture below for details: Step 3: Insert the gimbal into the Gimbal Lock. Ensure the white mark on the gimbal is aligned with the white mark on the left of the Gimbal Lock. Refer to the picture below for details: Step 4: With the gimbal in place, turn the Gimbal Lock to the left (when you are facing the nose of the DJI Inspire 1) until it locks in the position shown in the below. Now the gimbal is secured: 2. Attaching the Propellers Screw the propellers, clockwise for grey nuts and anti‐clockwise for black nuts, onto the four motors. Be sure to match the black propeller nuts with the black dot motors. Important:Make sure your smart flight battery and Micro‐SD care are inserted correctly. 3. Description of Aircraft Port (See the location on P) Micro‐USB Port: For connecting aircraft and PC Assistant to upgrade firmware. Camera Micro‐ USB Port: For connecting aircraft and PC to output the data to PC. Camera Micro‐SD Card Port: For placing the SD card. 4. Powering On Smart Flight Battery Press the circular power button once, then press again and hold for 2 seconds to power on the smart flight battery. (Repeat the above steps to power off the smart battery.) * Press circular power button once to check battery level. Preparing C1 1. Switch the flight mode switch to GPS mode, ensure the transformation switch is on the lower position. The return home function would be unavailable when fly in non‐GPS mode, and the aircraft only can maintain attitude and would be drift;The camera may be damaged if the transformation switch was not on the lower position before flight。 2. Description of C1 button and port Shutter Button:Press to take a photo. If burst mode is activated, multiple photos will be taken with a single press. Camera Settings Dial: Turn the dial to quickly adjust camera settings such as ISO, shutter speed, and aperture without letting go of the C1. Move the dial button to left or right to select your preferred settings. Playback Button: Press to view the images or videos that have already been captured. Recording Button: Press once to start recording video, then press again to stop recording. Flight Mode Switch: Toggle the switch to select the desired flight mode. You may choose between; GPS mode, OPTI mode and ATTI mode. Position 1:GPS mode Position 2:OPTI mode Position 3:ATTI mode Transformation Switch: This switch has two positions. The effect of toggling the switch to any of these four positions is defined below: 1) Raise, 2) Lower. 1)Raise: Raise the landing gear to its upper most position. 2)Lower: The landing gearr will lower to its lowestt position fo or landing. Deforma ation of aircrafft on the groun nd do not use function, so as a not to damage the camera. RTH H Button:Press and ho old this buttton to start the Return to Home (R RTH) proced dure. Thee LED around the RTH H Button willl blink whiite to indicaate the aircra aft is enttering RTH mode. The aircraft will then return n to the last recorded Home Poiint. Press th his button again to canccel the RTH H proceduree and regain n the con ntrol of the aircraft. USB B Port: Conn nect your mo obile device to the USB Port P to accesss all of the camera and aircrafft features av vailable in th he DJI app. HDM MI Port: Con nnect an HD D compatible monitor to o the HDMI port to see w what your cam mera sees in full f HD. Upg grade Port: Use U this portt to connect the GL658A A to a PC or Mac and up pgrade the firrmware. Thee relevant Assistant softtware must be b installed and open on yo our computeer. CAN N Port: Reseerved for futture use. 3. Co onnecting Mob bile Device an nd C1 Step 1: Positio on the mobilee device hold der as the piccture shown, then plug th he holder into o the mountting hole and tighten the scrrew. Step 2: Attach the t holder to neck strap attaachment and tighten. Step 3: Press th he button on th he side to hold d the mobile device and seccure. Step 4: Connect the mobile device to C1 USB port via micro‐USB cable. 4. Powering on C1 Press the power button once to check the current battery level. Press once and then press again and hold for 2 seconds to power on the C1. (Repeat the above steps again to power off the C1) Ready to Fly 1. Place the aircraft on flat ground in an open place with rear LED flight indicators facing you, and then power on the C1 and aircraft. 2. Connect C1 and mobile device. 3. Launch DJI App, make sure the GPS mode has been selected. 4. Calibrating Compass Always calibrate compass before your flight. Step 1: Go into the App camera GUI and tap the button, select “calibrate compass” to start the process, the rear LED flight indicator will be solid blue at this time. Step 2: Hold aircraft horizontally then rotate 360° around the center axis until rear LED flight indicator will be solid green. Step 3: Hold aircraft vertically with nose pointing to the ground, rotate 360° around the center axis until rear LED flight indicator will be blink purple. The process is completed. If rear LED flight indicator is solid red, calibration has failed. Re‐calibrate by repeating step 1‐3. 5. Description of rear LED indicator Blinking purple:GPS〉=6 or hover assistant is functioning,it is safe for flight. Blinking yellow: No GPS protection. Blinking red: System error occurs. * Refer to Appendix for more information. 6. Go into the camera GUI and tap check list, ensure everything is functioning normal. Flight 1. Taking off:Start motors by pulling both control sticks to the bottom corners. Release sticks once motors start. Slowly push the left(throttle) stick up to take off. Landing:Switch the transformation switch to lower position before landing. Gently pull the left (throttle) stick down to lower the aircraft until it touches the ground. When landing on the ground, pull the throttle stick to the bottom, then pull both sticks to bottom corners to stop motors. Power off the aircraft prior to power off the C1. 2. C1 Operation This section explains how to use the various features of the C1. C1 Aircraft (Mode 2) ( indicates nose direction) Remarks Moving the left stick up and down changes the aircraft’s elevation. Push the stick up to ascend and down to descend. Push the throttle stick up to takeoff. When both sticks are centered, the DJI Inspire 1 will hover in place. The more the stick is pushed away from the center position, the faster the DJI Inspire 1 will change elevation. Always push the stick gently to prevent sudden and unexpected elevation changes. Moving the left stick to the left or right controls the rudder and rotation of the aircraft. Push the sick left to rotate the aircraft counter clock‐wise, and push the stick right to rotate the aircraft clockwise. If the stick is centered, the DJI Inspire 1 will stay facing its current direction. The more the stick is pushed away from the center position, the faster the DJI Inspire 1 will rotate. Moving the right stick up and down changes the aircraft’s forward and backward pitch. Push the stick up to fly forward and down to fly backward. The DJI Inspire 1 will hover in place if the stick is centered. Push the stick further away from the center position n for a largeer pitch ang gle (maximu um 35˚) and fastter flight. Moving the right stick contrrol left and d right changess the aircraft’’s left and rig ght pitch. Push lefft to fly left and right to o fly right. The T DJI Inspire 1 will hover in place if th he stick is cen ntered. Push th he stick further away y from the center position n for a largeer pitch ang gle (maximu um 35˚) and fastter flight. Gimbal Dial: Turn the dial to the right, and the camera will shift to o point upwards. Turn the t dial to the left, and th he camera w will shift to o point downwards. The camera will remain in its current position wh hen dial is sttatic. 3. Reeturn Home Press and hold d the return ho ome button forr a while untill the LED surrround the buttton blinking white, th he return hom me procedure is i in process. Press once to stop the proceedure. It is reco ommend to taake off the airccraft until the rear LED lightt blinks purplee. Do not stop the motor during fligh ht. Aeriial Photograph 1. Seet the part off camera paraameter throug gh the camera a setting buttton on the C C1; Tap the sh hutter butto on\record buttton and play y back button to shutter\recording and preview the p picture; Adjusst the tilt angle of gimbal by using th he gimbal diall. 2. Seet all of the caamera parameeter, control caamera to shuttter \recording g and play baack via DJI Ap pp, it can also be use wh hen you are using ground station functiion. 3. Sy ynchronize the SD card datta to mobile device. App pendix GL L658A Status LE ED Statuss LED Solid Red Solid Green Allarm C1 Statu us None The GL658A is functioniing normallly but is not connected d with th he aircraft. None The GL658A is functioniing normallly and is con nnected witth the aiircraft. None Solid yellow Slow Blinkiing Red The C1 hass been set ass the slave B‐‐B‐B… … GL658A errorr. Launch th he Assistant software to learn more. BBB BB Warning thatt the aircraftt has low batttery level. Solid Green B‐‐B‐B… … T GL658A has been idlle for 10 min The nutes. RTH LED So ound Blinkiing Whitee …… B… Seending Retu urn to Homee command to the aircraaft. BB B…… Aircraft Retu urn to Homee in progresss. Fast Blinkiing Red GL658A Status BB‐‐BB BB Solid White Aircraft is retturning hom me The GL L658A Poweer LEDs will blink red, sound an alert, aand then automattically poweer off after 3 seconds when the batttery level iss critically low. If th his occurs during flightt, your DJI In nspire 1 will enter Failssafe Mode and Retu urn to Homee, which can nnot be interrrupted. C1 battery level in ndicator descrription Aircraft smart batttery indicatorr description The Battery Lev vel Indicatorrs display how much reemaining po ower the baattery has. When the battery is po owered off, press the Po ower Button n once. The Battery Leveel Indicatorss will ligh ht up to display the curreent battery level. See beelow for detaails. The Batteery Level In ndicators willl also show w the curren nt battery leevel during ch harging and discharging g. The indica ators are deffined below. :LED is on. :LED is flashing. :LED is off. Battery Level LED1 LED2 LED D3 LED4 Battery Level 87.5%~~100% 75%~887.5% 62.5%~~75% 50%~662.5% 37.5%~~50% 25%~337.5% 12.5%~~25% 0%~122.5% <0% Baattery Life The battery lifee indicates how many y more timees the batteery can be discharged and rech harged beforre it must be b replaced. When the battery is powered off, press and hold the Circular Po ower Button n for 5 seco onds to cheeck the batttery life. Th he Battery Level Indiicators will light up and d/or blink ass described below for 100 seconds: Battery Life LED1 LED2 LED D3 LED4 Battery y Life 90%~1100% 80%~990% 70%~880% 60%~770% 50%~660% 40%~550% 30%~440% 20%~330% 20% When batttery life reacches 0%, it can c no longeer be used. For more information n about the battery, laun nch DJI App p and check the informatio on under the battery tab b. 2.3 Charging the Smart Battery 1. Connect Batttery Chargeer to a poweer source (10 00‐240V 50/660Hz). 2. O Open the Prrotection Caap and conneect the Smarrt Battery to the Battery Charger. If the t battery level is abov ve 75%, turn on the batteery before charging. 3. The T Battery Level Indicator will dissplay the currrent battery y level durin ng charging. 4. The T Smart Battery is fullly charged when Batterry Level Ind dicators are aall off. Figure 7 Battery Level Indicaators while Charging LED1 LED2 LED D3 LED4 Battery Level 0%~225% 25%~550% 50%~775% 75%~1100% Fully Ch harged or Description Rearr LED indicato Reaar LED Flight In ndicator Status Pu urple lightss blinking quickly GPS signaal detected, and a more th han 6 GPS saatellites are connected Yelllow lightss blinking quickly GPS signaal detected, but b less than n 6 GPS sateellites are available Green lights slo owly Operating g in IOC mod de. blinking Reaar LED Flight In ndicator Warnings Yelllow and Green lights blin nking altern nately Compass calibration is i required. Yelllow lightss blinking quickly Low batteery level warrning. Red lights quickly blinking Critical low w battery warning Blu ue lights quickly blinking Wh hite lights quickly blinking C1 signal lost. IMU errorr If a systeem error occurs, conneect your DJII Inspire 1 to the DJI Inspire 1 Assistant for more deetailed diagn nostic inform mation and potential sollutions. Specifications Battery Model (Standard) Voltage Energy Net Weight Model (Option) Voltage Energy Net Weight Charger (Standard) Output Power Charging Time Charger (Option) Output Power Charging Time Camera Operating Temperature Resolution FOV (Field of View) CMOS Lens Shooting Mode HD Recording Mode Supported File Format Support SD Card Types GL658A Operating Frequency Transmitting Distance ( outdoor and unobstructed) Receiver(1%PER) EIRP TB47 22.2V 99.9Wh 570g TB48 22.8V 129.96Wh 570g 100W 85min for 4500mAh; 103 min for 5700mAh 180W 49min for 4500mAh; 56 min for 5700mAh 0℃ to 40℃ 1240M 94° 1/2.3” F/2.8(21mm equivalent) Anti‐distortion filter Single shoot Burst shoot(BURST:3/5/7 frames per second,AEB:3/5 frames per second,0.7EV Bias) Time lapsed UHD:4096x2160p24/25,3840x2160p24/25/30 FHD:1920x1080p24/25/30/48/50/60 HD:1280x720p24/25/30/48/50/60 FAT32/exFAT Photo format:JPEG,DNG Video format:MP4/MOV(MPEG‐4 AVC/H.264) SD/SDHC/SDXC Micro SD 5.728GHz~5.824GHz 2.400GHz~2.483GHz 2km or above ‐93dBm 8dBm @5.8G,20dBm@2.4G Working Current / Voltage Battery capacity 1.2A@7.4V 6000mAH Optical Flow Sensor Frequency 50HZ Velocity Range <8m/s ( 2m above ground) Altitude Range 5cm‐500cm Operating Environment Operating Range FAQ 。 。 。 。 。 。 Standard Logo Rich pattern surface with adequate lighting (Lux > 15) 0‐2.5m DJI Inspire 1 should be installed and operated with minimum distance 20cm between the radiator& your body. DJI Inspire 1 should be installed and operated with minimum distance 20cm between the radiator& your body.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2014:10:31 15:22:53+08:00 Create Date : 2014:10:31 15:22:53+08:00 Format : application/pdf Title : Microsoft Word - NEW User Manual.docx Creator : elena Document ID : uuid:72848d49-012a-4fde-8481-0db35512f8e7 Instance ID : uuid:2271f972-3e44-4878-8e58-8c11f1fd0187 Page Count : 20 Author : elenaEXIF Metadata provided by EXIF.tools