SZ DJI TECHNOLOGY MG1P1801 MG-1P RTK, MG-1P User Manual MG 1P Quick Start Guide 20180123
SZ DJI TECHNOLOGY CO., LTD MG-1P RTK, MG-1P MG 1P Quick Start Guide 20180123
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3777061 |
| Application ID | gcJU2K4U8pqRG99eFQdmTA== |
| Document Description | User Manual |
| Short Term Confidential | Yes |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 38.97kB (487074 bits) |
| Date Submitted | 2018-03-12 00:00:00 |
| Date Available | 2018-04-26 00:00:00 |
| Creation Date | 2018-05-24 18:26:36 |
| Producing Software | GPL Ghostscript 9.21 |
| Document Lastmod | 2018-05-24 18:26:36 |
| Document Title | Microsoft Word - MG-1P Quick Start Guide 20180123 |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | DG06188 |
MG-1P / MG-1P RTK Quick Start Guide V1.0 Aircraft(Model: 3WWDSZ-10016/3WWDSZ-10017) The Agras MG-1P series (MG-1P / MG-1P RTK) aircraft is equipped witha wide-angle FPV camera, observing the operating environment in front to offer reality references for planning operation area and flying with obstacle avoidance remotely. The second generation high-precision radar, integrated the forward, backward and downward altitude stabilization radar modules and obstacle avoidance radar module, improves its functions of obstacle sensing and terrain following. The aircraft body, using new structures and materials, is dust-proof, water-proof (IP43 protection rating, IEC standard 60529) and anti-corrosive. The MG-1P / MG-1P RTK contains DJI’s dedicated A3 redundancy system with eight-rotor propulsion redundancy, ensuring safe and stable operation at all times.The MG-1P RTK has a built-in DJI Onboard D-RTK*, which provides more accurate data for centimeter-level positioning. 1Propellers 2FrameArms 3Motors 4ESCLED 5Sprinklers 6ReliefValve 7Nozzles 8Hoses 9LinkButton(rearoftheaircraft) 10PumpPorts 11RadarPort 12MicroUSBPort 13FlowMeterPort 14LandingGear 15PumpCables 16FlowMeter 17DeliveryPumps 18FlowMeterCable 19SprayTank 20AircraftBody 21GNSSModule 22FPVCamera(frontoftheaircraft) 23IntakeVent 24PowerPort 25BatteryCompartment 26RadarCable 27RadarModule 28RemoteControllerHolder 29OcuSyncAntenna 30OnboardD-RTKAntennas(for MG-1PRTKonly) ●DO NOT obstruct the GNSS module located at the center of the aircraft, as this will reduce the GPS signal strength. ●The MG-1P / MG-1P RTK does not come with a battery. Please purchase the DJI approved battery pack (Model: MG-12000P). *ThisshouldbeusedwithaDJIBaseStation(purchasedadditionally)orDJIapprovedNetworkRTKservice. Remote Controller(Model: GL300N) Fully upgraded remote controller usessecond-generation DJI OcuSync dual-band video downlink system which has a maximum control distance of up to 3 km. The remote controller is equipped with a bright, dedicated screen with a built-in brand new DJI MG app. Operation area planning supports using both the remote controller and aircraft to set waypoints.Smooth turning of the operation route is added, with the new spraying system, making flight and operation more flexible and efficient. The remote controllerfeatures a function of multi-drone control with a single remote controller. It can coordinate up to fivedrones for operation at the same time, which further improves the efficiency of a single operator. Replaceable batteries and antennas of the remote controller make it easy for daily operation and maintenance. 1Antennas 6PowerButton 2DisplayDevice 7StatusLED 3Speaker 8BatteryLevelLEDs 4ControlSticks 9RTHStatusLED 5LanyardAttachment 10RTHButton For example, the following description uses Mode 2. The left stick controls the aircraft altitude and heading, while the right stick controls its forward, backward, left and right movements. Installation ●Threadlocker of medium strength is required for installation. Apply threadlocker when mounting the landing gear, power port module, spray tank, sprinklers and radar module. Ensure threadlocker is totally dry and solid before flight. ●DO NOT bend the hose in an arc tighter than its minimum bend radius during installation. This is to avoid creasing, which may compromise the spraying effect. ●Ensure that all installation and connection procedures are completed before powering on the aircraft. Mounting the Battery Insert the battery into the battery compartment from the front of the aircraft. Ensure the battery is securelymounted and then buckle the belt to the button of the spray tank. Power Port Belt Button ●TheMG-1P/ MG-1P RTK does not come with a battery. Please purchase the DJI approved MG-1S battery pack (Model: MG-12000P). ●The voltage on the aircraft can reach 50.4 V. Read the battery’s safety guidelines and take necessary precautions when handling the battery to ensure your own safety. Fly Safe It is important to understand some basic flight guidelines, both for your protection and for the safety of thosearound you. 1. Flying in Open Areas: Do not fly near or above people or animals, or near buildings, power lines and other obstacles. 2. Maintain Control at All Times: Always keep your hands on the remote controller and maintain control of your aircraft when it is in flight, even when using intelligent functions such as Intelligent Operating Planning System, Smart Operation Mode and Smart Return-to-Home. 3. Maintain Line of Sight: Maintain a line of sight to your aircraft at all times and avoid flying behind buildings or other obstacles that may block your view. 4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 164 feet (50 meters) or according to local laws and regulations. Visit https://www.dji.com/flysafe/geo-map for more information on critical safety features such as No Fly Zones. Return-to-Home It is important to take off with a strong GNSS signal to ensure that the Home Point is recorded by the aircraft.The aircraft will automatically return to the Home Point in the following cases. Smart RTH: You press the RTH button. Failsafe RTH*: Remote controller signal is lost. The aircraft can sense obstacles at a distance up to30 meters, then automatically avoid obstacle andfly to the Home Point. * The Failsafe RTH must be enabled in the DJI MG app. If not enabled, the aircraft will hover in place when remote controllersignal is lost. Using MG-1P/ MG-1P RTK Preparing the Flight Battery Only use DJI approved flight batteries (Model: MG-12000P). Checkbattery level before flying and charge according to instructions providedby the manufacturer. Preparing the Remote Controller Checking Battery Level Low → High Press once to check the battery level.Press once, then again and hold to turn on/off. Charging the Battery Press the battery level button once to check the battery level. Fully charge the batteries before first-time use. 1. Place the battery into the Charging Hub, connect the charger to the Charging Hub, and then connect the charger to a power outlet (100 - 240V, 50/60Hz). 2. The Charging Hub will intelligently charge batteries in sequence according to battery power levels from high to low. 3. The Status LED blinks green when charging and turns solid green when fully charged. The buzzer will begin beeping when charging is complete. Remove the battery or turn off the buzzer to stop it. Adjusting the Antennas Tilt the display device on the remote controller to the desired position, then adjust the antennas so they are facingoutward. The strength of the remote controller signal will fluctuate depending on the position of the antennas. Unfold Stron Week Try to keep the aircraft inside the optimal transmission range. If the signal is weak, adjust the antennas or fly theaircraft closer. Optimal Transmission Range ●Avoid using wireless devices that use the same frequency bands as the remote controller. Getting Ready for Takeoff When using your MG-1P / MG-1P RTK for the first time, activate it in the DJI MG app. Your DJI account andinternet connection are required. 1. Place the aircraft on an open, flat ground with the Aircraft Status Indicator facing towards you. 2. Unfold the propellers and check that they are mounted onto the motors securely. Unfold frame arms andtighten arm sleeves firmly. 3. Power on the remote controller. 4. Ensure the battery is securely mounted. Connect the battery to the power porton the aircraft. Flight Enter the Operation View of the DJI MG app. Ensure that there is a strong GNSS signal and the operation mode is M mode (Manual). Otherwise the aircraft cannot take off. Takeoff Perform the Combination Stick Command (CSC) and then slowly push the throttle stick up to take off. OR Throttle Stick Landing To land, pull down on the throttle stick down to descend until the aircraft touches the ground. There are two methods to stop the motors. 1. When the aircraft has landed, push the throttle down and hold. The motors will stop after 3 seconds. Throttle Stick 2. When the aircraft has landed, push the throttle stick down, then perform the CSC command to stop the motors. Release both sticks once the motors have stopped. OR Throttle Stick Intelligent Operation Planning System The remote controller equips a highlighted screen with a built-in Android system, which can run the DJI MGapp. Measure operation area and obstacles, configure waypoints, and other settings via the intelligent operationplanning system built-in the app, and the app will produce a flight route according to the settings. The aircraft canoperate automatically following the flight route. Specifications Airframe Diagonal Wheelbase 1500 mm Frame Arm Length 619mm MG-1P: 1460 mm1460 mm578 mm(Frame arms unfolded, propellers removed) 780 mm780 mm578 mm(Frame arms folded) Dimensions MG-1P RTK: 1460 mm×1460 mm×616 mm(Frame arms unfolded, propellers removed) 780 mm780 mm616 mm(Frame arms folded) Diameter × Pitch 217 inch Propeller Weight 58 g Operating Frequency 2.400 GHz to 2.483 GHz 5.725 GHzto 5.850 GHz (not supported in Japan) EIRP 2.4 GHz FCC: ≤26 dBm, CE: ≤20 dBm,SRRC(China): ≤20 dBm, KCC(Korea): ≤18 dBm, MIC(Japan): ≤18 dBm 5.8 GHz FCC: ≤26 dBm, CE: ≤14 dBm, SRRC (China): ≤26 dBm, KCC(Korea): ≤14 dBm Radar Module Model RD2412R Operating Frequency SRRC / CE / FCC: 24.00 GHzto 24.25 GHz MIC / KCC:24.05 GHzto 24.25 GHz Power Consumption 12 W EIRP SRRC: 13 dBm, FCC: 20 dBm, CE: 20 dBm, MIC: 20 dBm, KCC: 20 dBm Altitude Detection and Stabilization Detection Range: 1 - 30 m Stabilization Working Range: 1.5 - 3.5 m IP Rating IP67 Flight Parameters Total Weight (Excluding battery) MG-1P: 9.7kg, MG-1P RTK: 9.9 kg Standard Takeoff Weight 23.7 kg Max Takeoff Weight 24.8 kg(At sea level) Max Thrust-Weight Ratio 1.71(Takeoff weight of 23.7 kg) GNSS GPS+GLONASS Battery DJI approved battery pack (Model: MG-12000P) Max Power Consumption 6400 W Hovering Power Consumption 3800 W(Takeoff weight of 23.7 kg) Hovering Time* 22 min (Takeoff weight of 14 kg with Hovering Time* 20 min (Takeoff weight of 13.7 kg with a 12000 mAh battery) 9 min (Takeoff weight of 23.7 kg with a 12000 mAh battery) Max Service Ceiling Above Sea Level 2000 m Operating Temperature 32° to 104° F (0° to 40° C) Remote Controller (Model: GL300N) Model GL300N Operating Frequency 2.400 GHz to 2.483 GHz 5.725 GHzto 5.850 GHz (not supported in Japan) Max Transmitting Distance 3 km (unobstructed, free of interference) EIRP 2.4 GHz FCC: ≤26 dBm, CE: ≤20 dBm,SRRC(China): ≤20 dBm, KCC(Korea): ≤18 dBm, MIC(Japan): ≤18 dBm 5.8 GHz FCC: ≤26 dBm, CE: ≤14 dBm, SRRC (China): ≤26 dBm, KCC(Korea): ≤14 dBm 5.5 inch screen, 1920×1080, 1000 cd/m2, Android Display Device system, 4G RAM+16G ROM Operating Temperature 14° to 104° F (-10° to 40° C) Storage Temperature Less than 3 months: -4° to 113° F (-20° to 45° C) More than 3 months: 72° to 82° F (22° to 28° C) Charging Temperature 41° to 104° F (5° to 40° C) Remote Controller Intelligent Battery Model WB37-4920mAh-7.6V Battery Type LiPo battery Capacity 4920 mAh Voltage 7.6 V Energy 37.39 Wh Charging Temperature 41° to 104° F (5° to 40° C) Charging Hub Model WCH2 Input Voltage 17.3 - 26.2 V Output Voltage and Current 8.7 V,6 A;5 V,2 A Operating Temperature 41° to 104° F (5° to 40° C) AC Power Adapter Model A14-057N1A Voltage 17.4 V Rated Power 57 W FCC ComplianceNotice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate thereceiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information Aircraft complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. For Remote Controller (model GL300N),SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each product are performed in positions and locations as required by the FCC. For body worn operation, Remote Controller (model GL300N) has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal. For body worn operation, GL300N has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal and that positions the handset a minimum of 10 mm from the body. Non-compliance with the above restrictions may result in violation of RF exposure guidelines. EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the RED Directive. This Aircraft must be installed and operated in accordance with provide instructions and the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operation in conjunction with any other antenna or transmitter.End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance Warning: Operation of this equipment in a residential environment could cause radio interference.
Source Exif Data:
EXIF Metadata provided by EXIF.tools