SZ DJI TECHNOLOGY U11X1710 MAVIC AIR User Manual

SZ DJI TECHNOLOGY CO., LTD MAVIC AIR Users Manual

Users Manual

Download: SZ DJI TECHNOLOGY U11X1710 MAVIC AIR User Manual
Mirror Download [FCC.gov]SZ DJI TECHNOLOGY U11X1710 MAVIC AIR User Manual
Document ID3720503
Application IDSgKdEZ4QYGSLWt6KOuII8w==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize103.33kB (1291669 bits)
Date Submitted2018-01-19 00:00:00
Date Available2018-03-09 00:00:00
Creation Date2017-10-13 15:54:09
Producing SoftwareMicrosoft® Word 2013
Document Lastmod2018-01-16 15:30:19
Document TitleUsers Manual
Document CreatorMicrosoft® Word 2013
Document Author: Joyce Yan

WM230 Quick Start Guide
V1.0 2017.11
Aircraft
The WM230 featuring a fully stabilized camera, Intelligent Flight Modes and Obstacle Avoidance
inside an upgraded revolutionary folding design. It captures 4K videos and 12 megapixel photos,
and is capable of both ActiveTrackTM and TapFlyTM making complex shots effortless. WM230 boasts
a maximum flight speed of 42.5 mph (68.4 kph) and a maximum flight time of 22 minutes.
1.
2.
3.
4.
5.
Forward Vision System
Gimbal and Camera
Propellers
Motors
Front LEDs
6.
7.
8.
9.
10.
11.
12.
13.
14.
USB Type-C Port
Downward Vision System
Backward Vision System
Antennas
Camera Micro SD Card Slot
Aircraft Status Indicator
Intelligent Flight Battery
Power Button
Battery Level LEDs
** Maximum flight time was tested in 0 wind at a consistent 15.5 mph (25 kph). This value should
be taken for reference only.
** The Forward and Backward Vision Systems are affected by surrounding conditions. Read the
Disclaimer and Safety Guidelines and watch the tutorial in the DJI GOTM 4 app or on the Official DJI
website to learn more.
Remote Controller
The Remote Controller offers a maximum transmission range of 2.49 mi (4 km). Video from the
aircraft to the DJI GO 4 app on your mobile device at up to 1080p at close range, and 720p at longer
ranges. The WM230 can also be flown by phone only.
1. Flight Mode Switch
2. Function Button
3. Control Sticks
4. Antennas
5. Power Button
6. Mobile Device Clamp
7. Charging Port (USB Type-C)
8. Flight Pause Button
9. RTH Button
10. Status LED
11. Battery Level LEDs
12. Gimbal Dial
13. Customizable Button
14. Record Button
15. Shutter Button
The remote controller is able to reach its maximum transmission distance (FCC) in a wide open
area with no Electro-Magnetic Interference, and at an altitude of about 400 feet (120 meters).
Specifications
 Aircraft (Model: U11X)
Weight
Max Speed
Max Flight Time
Operating Temperature
Satellite Positioning Systems
Operating Frequency
Transmitter Power (EIRP)
● Gimbal
Controllable Range
430 g
42.5 mph (68.4 kph) in Sport Mode without wind
22 minutes (0 wind at a consistent 15.5 mph (25 kph))
32° to 104° F (0° to 40° C)
GPS+GLONASS
2.4-2.4835 GHz; 5.725-5.850 GHz*
2.4G: 26 dBm (FCC), 18.59 dBm (CE), 18 dBm (SRRC)
5.8G: 31.39 dBm (FCC), 13.96 dBm (CE), 30 dBm (SRRC)
Pitch: -90° to +0° (Default settings), -90° to +22° (Customized)
● Camera
Sensor
CMOS
Max Image Size
4000×3000
Still Photography Modes
Single shot, Burst shooting
Video Recording Modes
3840×2160
Video Storage Bitrate
100 Mbps
Video
MP4
Supported SD Cards
microSD
● Remote Controller (Model: S01A)
Dimensions
143.9x78.3x61.2 mm
Operating Frequency
2.4-2.4835 GHz; 5.725-5.850 GHz*
Max Transmission Distance
2.4G FCC: 2.5 mi (4 km); CE/SRRC: 0.6 mi (1 km)
5G FCC: 2.5 mi (4 km); CE: 0.4 mi (0.6 km); SRRC: 0.6 mi (1 km)
Unobstructed and free of interference.
Operating Temperature
32° to 104° F (0° to 40° C)
Battery
2970 mAh
Transmitter Power (avg. EIRP)
Operating Voltage
Supported Mobile Device Size
Supported USB port types
2.4G: 26 dBm (FCC), 18 dBm (CE), 18 dBm (SRRC)
5.8G: 30 dBm (FCC), 14 dBm (CE), 26 dBm (SRRC)
1000 mA @ 3.7 V
Thickness supported: 6.5 - 8.5 mm, Max length: 160 mm
Lightning, Micro USB (Type-B), USB Type-CTM
● Charger
Voltage
Rated Power
13.2 V
50 W
● Intelligent Flight Battery
Capacity
Voltage
Battery Type
Energy
Net Weight
Charging Temperature Range
Max Charging Power
2375 mAh
11.55 V, Max 13.2 V
LiCo02
27.43 Wh
Approx. 0.3 lbs (140 g)
41° to 104° F (5° to 40° C)
60 W
Download the DJI GO 4 App and Watch the Tutorial Videos
Search for ‘DJI GO 4’ on the App Store or Google Play, or scan the QR code to download the app on
your mobile device. Watch the tutorial videos at www.dji.com or in the DJI GO 4 App.
Charge the Batteries
Remove Intelligent Flight Battery
Charge the batteries
1. Connect the charger to power outlet
2. Connect the charger to Intelligent Flight Battery
3. Connect the Remote controller to the charger
Check the Battery Levels
Press once to check the battery level. Press once, then again and hold to turn on/off.
Press the Power button once to check the current battery level. Press once, then again and hold to
turn on/off the remote controller.
Prepare the Remote Controller
Unfold the antennas and the mobile device clamp
Place one end of the RC cable to the end of the slot
Attach mobile device
Prepare the Aircraft
1. Remove the gimbal clamp from the camera
2. Unfold the rear arms
3. Unfold the front arms
4. Unfold the landing gear
Prepare for Takeoff
1. Power on the remote controller
2. Power on the aircraft
3. Launch the DJI GO 4 App
Flight
•
Takeoff/Landing
Before taking off, make sure the Aircraft Status Bar in the DJI GO 4 app displays ‘Ready to Go’
•
Remote Controller Operation
•
Controlling flight with Virtual Joysticks on your mobile device via Wi-Fi
1. Toggle the Control Mode Switch to turn on Wi-Fi
2. Power on the aircraft
3. Launch the DJI GO 4 app and tap the icon on the top right of your screen, then scan the WiFi QR Code on the front arm to start connection
4. Tap Auto Takeoff
5. Fly the aircraft with touch control
•
In the DJI GO 4 App
Fly Safe
Compliance Information
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
The Aircraft and Remote controller complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits,
human body proximity to the Aricraft antenna shall not be less than 20cm during normal operation.
RSS Warning
This device complies with ISEDC licence-exempt RSS standard (s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Radiation Exposure Statement:
The Aircraft and Remote Controller complies with RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The Aircraft should be installed and operated with minimum distance 20cm between the
radiator& your body.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
KCC Warning Message
“해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는
할 수 없습니다.”
“해당 무선설비는 운용 중 전파혼신 가능성이 있음”
NCC Warning Message
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,
應改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功
率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in
compliance with the essential requirements and other relevant provisions of the Directive
2014/53/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance
EU contact address: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Declaración de cumplimiento UE: SZ DJI TECHNOLOGY CO., LTD. por la presente declara que este
dispositivo cumple los requisitos básicos y el resto de provisiones relevantes de la Directiva
2014/53/EU.
Hay disponible online una copia de la Declaración de conformidad UE en www.dji.com/eurocompliance
Dirección de contacto de la UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
EU-verklaring van overeenstemming: SZ DJI TECHNOLOGY CO., LTD. verklaart hierbij dat dit
apparaat voldoet aan de essentiële vereisten en andere relevante bepalingen van Richtlijn
2014/53/EU.
De EU-verklaring van overeenstemming is online beschikbaar op www.dji.com/euro-compliance
Contactadres EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Declaração de conformidade da UE: A SZ DJI TECHNOLOGY CO., LTD. declara, através deste
documento, que este dispositivo está em conformidade com os requisitos essenciais e outras
disposições relevantes da Diretiva 2014/53/EU.
Existe uma cópia da Declaração de conformidade da UE disponível online em www.dji.com/eurocompliance
Endereço de contacto na UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Dichiarazione di conformità UE: SZ DJI TECHNOLOGY CO., LTD. dichiara che il presente dispositivo
è conforme ai requisiti essenziali e alle altre disposizioni rilevanti della direttiva 2014/53/EU.
Una copia della dichiarazione di conformità UE è disponibile online all'indirizzo Web
www.dji.com/euro-compliance
Indirizzo di contatto UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Déclaration de conformité UE : Par la présente, SZ DJI TECHNOLOGY CO., LTD déclare que cet
appareil est conforme aux principales exigences et autres clauses pertinentes de la directive
européenne 2014/53/EU.
Une copie de la déclaration de conformité UE est disponible sur le site
www.dji.com/euro-compliance
Adresse de contact pour l'UE : DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
EU-Compliance: Hiermit erklärt SZ DJI TECHNOLOGY CO., LTD., dass dieses Gerät den wesentlichen
Anforderungen und anderen einschlägigen Bestimmungen der EU-Richtlinie 2014/53/EU
entspricht.
Eine Kopie der EU-Konformitätserklärung finden Sie online auf www.dji.com/euro-compliance.
Kontaktadresse innerhalb der EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the
residual waste, but have to be disposed of separately. The disposal at the communal
collecting point via private persons is for free. The owner of old appliances is
responsible to bring the appliances to these collecting points or to similar collection
points. With this little personal effort, you contribute to recycle valuable raw materials
and the treatment of toxic substances.
Thailand Warning message
เครื่ องโทรคมนาคมและอุปกรณ์น้ ี มีความสอดคล้องตามข้อกาหนดของ กทช.
Mexico Warning message
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este
equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar
cualquier interferencia, incluyendo la que pueda causar su operación no deseada.”
Brazil Warning message
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a
sistemas operando em caráter primário

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Joyce Yan
Create Date                     : 2017:10:13 15:54:09+08:00
Modify Date                     : 2018:01:16 15:30:19-08:00
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : Joyce Yan
Creator Tool                    : Microsoft® Word 2013
Metadata Date                   : 2018:01:16 15:30:19-08:00
Producer                        : Microsoft® Word 2013
Document ID                     : uuid:ecefd2ba-0ea2-4463-812b-86ca5f8b9557
Instance ID                     : uuid:3ce8525f-3825-41b8-b8c0-ed5c761cb316
Page Count                      : 14
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SS3-U11X1710

Navigation menu