SZ DJI TECHNOLOGY ZT300A1604 DATALINK PRO 900 User Manual x

Download:
Mirror Download [FCC.gov]
Document ID	3016578
Application ID	k26+6t9c9T13yQ3S6n8+Ag==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	64.02kB (800252 bits)
Date Submitted	2016-06-03 00:00:00
Date Available	2016-11-30 00:00:00
Creation Date	2016-05-23 14:46:02
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2016-06-01 09:15:30
Document Title	Microsoft Word - user manual.docx
Document Creator	PScript5.dll Version 5.2
Document Author:	elena

Disclaimer
Thank you for purchasing the Datalink Pro hereinafter referred to as “product” . Read this disclaimer
carefully before using this product. By using this product, you hereby agree to this disclaimer and signify
that you have read it fully. Please install and use this product in strict accordance with the User Manual. SZ
DJI Technology Co., Ltd. and its affiliated companies assume no liability for damage s or injuries incurred
directly or indirectly from using, installing or refitting this product improperly, including but not limited to
using non‐designated accessories.
DJI is the registered trademark of SZ DJI Technology Co., Ltd. abbreviated as “DJI” . Names of products,
brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner
companies. This product and manual are copyrighted by DJI with all rights reserved. No part of this product
or manual shall be reproduced in any form without the prior written consent of or authorization from DJI.
This disclaimer is produced in various languages. In the event of variance among different versions, the
Chinese version shall prevail when the product in question is purchased in Mainland China, and the English
version shall prevail when the product in question is purchased in any other region.
Warnings
1.
Only use the Datalink Pro in the corresponding frequency band and in accordance with local laws and
regulations.
2.
Ensure all modules are connected and the parameters are set correctly in DJI Assistant 2 when using
the Datalink Pro for the first time.
3.
DO NOT bend or fold the antennas excessively.
4.
Ensure the antennas for both the mobile station and the Base Station are unobstructed when used.
5.
Only use the Datalink Pro in an open environment free from radio interference.
6.
Only pair the Datalink Pro Base Station with a mobile station in the same frequency band. Note that the
400M Datalink Pro and 900M Datalink Pro are not compatible.
7.
When upgrading the firmware, toggle the 4‐position switch to the COMBO_SW4 position, connect the
module to the PC, and then run DJI Assistant 2.
8.
To avoid interference, DO NOT use a two‐way transceiver or walkie‐talkie operating near the 400 MHz
band when operating the 400M Datalink Pro.
9.
Only use genuine DJI parts or parts certified by DJI. Unauthorized parts or parts from non‐DJI‐certified
manufacturers may cause system malfunctions and compromise safety.
10. Ensure the Datalink Pro and its components are free from contamination e.g. water, oil, soil and sand .
Contents
Disclaimer ..................................................................................................................................................................................................... 2
Warnings ....................................................................................................................................................................................................... 2
About............................................................................................................................................................................................................... 4
Part Description * ...................................................................................................................................................................................... 4
Installation and Connection .................................................................................................................................................................. 5
Usage ............................................................................................................................................................................................................... 6
Linking Procedures ......................................................................................................................................................................... 6
Configuring Parameters Using the DJI Assistant 2 ............................................................................................................. 6
Using the DJI Ground Station ...................................................................................................................................................... 7
Working Status LED ........................................................................................................................................................................ 7
Appendix ....................................................................................................................................................................................................... 8
Specifications ..................................................................................................................................................................................... 8
Compliance Information ......................................................................................................................................................................... 9
FCC Compliance Notice .................................................................................................................................................................. 9
RF Exposure Information ............................................................................................................................................................. 9
IC RSS Warning................................................................................................................................................................................10
KCC Warning Message ..................................................................................................................................................................10
NCC Warning Message .................................................................................................................................................................10
EU Compliance Statement ..........................................................................................................................................................10
About
The Datalink Pro is used for wireless data transmission, including communication between the Mobile
Station and Base Station. There are 400M and 900M versions to meet the requirements of different regions.
The multi‐functional bidirectional transmission link is perfect for the DJI A3 flight control system, D‐RTK
and Ground Station. Use frequency bands of near 400 MHz and 900 MHz to avoid radio interference with the
DJI Lightbridge and remote controller. Support for multiple interfaces, such as USB, CAN and UART, offers
additional connectivity.
Part Description *
Base Station
B.
UART port with baud rate up to 115200
1.
Antenna Interface
2.
Working Status Indicator
3.
Linking Button
4.
Micro USB
5.
8‐pin Port
B1: Power DC9V input
A.
B2: GND
bps, working in TTL level logic of 3.0–3.3V
compatible with 5 V, but not recommended
to work at 5 V long term .
CAN port with baud rate of 1 Mbps.
A1: Power DC9V input
B3: UART‐RX
A2: GND
B4: UART‐TX
A3: CAN‐H
6.
4‐position Switch
C1：UART_SW1
A4: CAN‐L
C2：CAN_SW2
C3：USB_SW3
C4：COMBO_SW4
Mobile Station
1.
Antenna Interface
2.
Linking Button
3.
Micro USB
4.
8‐pin Port Definition is the same as the Base
Station
5.
4‐position Switch Definition is the same as the
Base Station
6.
Base Station Antenna*
Working Status Indicator
900M Antenna 1
400M Antenna 1
Mobile Station Antenna *
400M Antenna 3 1pcs for standby
900M Antenna 3 1pcs for standby
Accessories
8‐pin Cable x 2
Micro USB Cable x 1
Double‐sided tape
*The 400M and 900M Datalink Pro use different antennas but have the same functions.
Installation and Connection
The following uses the 900M Datalink Pro, DJI Matrice 600, D‐RTK and DJI Intelligent Flight Battery to
illustrate a typical installation and connection.
1.
Attach the Base Station antenna and install it on the D‐RTK Ground System’s base board with a screw
included with the D‐RTK product . Then connect the Base Station and the D‐RTK Ground System via
an 8‐pin cable.
2.
Install the Mobile Station to the DJI Matrice 600 with double‐sided tape. Attach the antennas to the
Mobile Station and fix them to the landing gears with two clips. Then connect the Mobile Station and
the D‐RTK Air System via an 8‐pin cable.
Notes:
1.
Be sure to toggle the 4‐position switch to the UART_SW1 position if using the D‐RTK, otherwise the
D‐RTK may fail to receive data from the Datalink Pro.
2.
Refer to the “D‐RTK Quick Start Guide” for details if using the D‐RTK.
Usage
Use the Datalink Pro in an open environment free from radio interference.
Linking Procedures
Base Station and Mobile Station are linked before leaving the factory.
Note that frequency linking is required if any device is changed or added.
1.
Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Base Station.
2.
Hold the Base Station’s Linking Button for about 3 seconds to enter the linking mode with the Working
Status LED blinks red and green alternatively.
3.
Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Mobile Station.
4.
Hold the Mobile Station’s Linking Button for about 3 seconds and wait for linking.
5.
The Base Station and Mobile Station will connect with each other if successfully linked.
6.
Follow procedures 2–5 to link other Mobile Stations to set up a single‐to‐multiple system.
Configuring Parameters Using the DJI Assistant 2
DJI Assistant 2 should be used to upgrade the Datalink Pro. Full Duplex Mode and Broadcast Mode can be
switched in DJI Assistant 2
1.
Download DJI Assistant 2 from www.dji.com and install it on your computer.
2.
Toggle the 4‐position switch to the COMBO_SW4 position, connect the Base Station to the computer
with DJI Assistant 2 launched, and then configure parameters according to the message prompts.
3.
Configure the Mobile Station in the same way. If multiple Mobile Stations are used, you must configure
each Mobile Station one by one.
Notes:
Power cycle the Datalink Pro, Flight Control System and D‐RTK after upgrading.
Supports Windows 7 or later or Mac OS X 10.9 or later .
Using the DJI Ground Station
Ensure the A3 Flight Control System, Datalink Pro and D‐RTK are connected correctly before powering on.
1.
Connect the Base Station to the PC via a Micro USB cable, and then run the Ground Station.
2.
Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Base Station first.
3.
Enable the D‐RTK Ground System’s battery to power on the Datalink Pro Mobile Station.
Note:
The DJI Ground Station supports up to five Air Systems in Full Duplex Mode. The 4‐position switch should be
set to the COMBO_SW4 position. Download the User Manual from www.dji.com to learn more.
Refer to the “DJI Ground Station User Manual” for details if using the DJI Ground Station.
Working Status LED
LED
Description
Blinking Red
Parameter error after powering on. If not resolved by power
cycling, contact your dealer.
Blinking Purple
Connected to the Assistant successfully.
Blinking Yellow
Upgrading or preparing for upgrade.
Quickly Blinking Green for 1
Current system setting is saved Run mode changed successfully ,
Second
or connected device information is clear.
Solid Blue
Mobile Station: Working in Broadcast Mode.
Base Station: Working in Broadcast Mode and receiving the data
from Mobile Station.
Solid Green
Mobile Station: Mobile Station connected correctly in Full Duplex
Mode.
Base Station: At least one Mobile Station connected to the Base
Station in Full Duplex Mode.
Solid Red
Mobile Station: All Mobile Stations are disconnected in both Run
Modes.
Base Station: All Mobile Stations are disconnected in Full Duplex
Mode.
Blinking Red and Green
Linking in progress.
Alternatively
Blinking Yellow Twice
4‐position switch is toggled successfully.
Solid White for 1 Second
Device is initializing, only displays when powering on.
Appendix
Specifications
Type
DATALINK PRO 400M
DATALINK PRO 900M
Performance
Outdoor/RF Line‐of‐Sight Range
Approximately 2000m
Transmit Power
China: 10dBm
CE: 20dBm
Taiwan: 10dBm
FCC: 25.42dBm
South Korea: 10dBm
Canada: 25.42dBm
Australia: 24dBm
Japan: 13dBm
Power Consumption
Mobile Station: 0.65 W
Mobile Station: 0.65 W
Base Station: 2.1 W
Base Station: 1.2 W
China: 430‐432
CE: 869.525
Taiwan: 429.175‐429.2375
FCC: 906‐924
South Korea:
Canada: 906‐924
447.8625‐447.9875
Australia: 918‐925
Features
Frequency Band MHz
Japan: 923.1‐926.3
Serial Data Rate
Max. 115200bps
Antenna Options
Vertically polarized
Supported Interfaces
USB, UART, CAN
Supported DJI Products
A3, D‐RTK, Ground Station
Operating Temperature
32° to 113°F 0° to 45°C
Storage Temperature
‐40° to 185°F ‐40° to 85°C
Humidity
5% to 95%, non‐condensing
Dimension without Antenna
Base Station: 83 mm x 51 mm x 14.5 mm
Mobile Station: 58 mm x 42.3 mm x 9.5 mm
Weight without Antenna
Base Station: 24 g
Mobile Station: 53 g
Power Supply
Voltage
Base Station: DC 9 V
Mobile Station: DC 9 V
Max.
Current
Transmitting
230 mA
130 mA
Signal
Max. Current Receiving Signal
70 mA
Compliance Information
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1
This device may not cause harmful interference, and 2 This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the
anten
nna shall not be
b less than 20cm during norrmal operation
n.
IC RSSS Warning
This device compllies with Industry Canada liicence‐exemptt RSS standard
d s . Operatio
on is subject to
t the
follow
wing two cond
ditions: 1 th
his device may
y not cause intterference, and
d 2 this device must accep
pt any
interrference,includ
ding interference that may caause undesired
d operation of the
t device.
Le présent appareil est conform
me aux CNR d'IIndustrie Canaada applicabless aux appareills radio exemp
pts de
licen
nce.
L'exp
ploitation est autorisée
aux deux
conditions suivantes:
1 l'appareil ne do
oit pas produirre de brouillage, et
2 l'utilisateur
dee l'appareil doit accepter tou
ut brouillage radioélectriqu
e subi, même si le brouillag
ge est
susceeptible d'en co
ompromettre lee fonctionnement.
IC Raadiation Expossure Statementt:
This equipment co
omplies with IC RF radiation
n exposure lim
mits set forth for
f an uncontrrolled environment.
This transmitter must
not be co‐llocated or operating in conju
unction with an
ny other antenna or transmittter.
This equipment should be installled and operatted with minim
mum distance 20cm
between
n the radiator&
& your
body
y.
Any Changes or modifications
not expressly approved
by th
he party respo
onsible for com
mpliance could
d void
the user’s
authority
y to operate th
he equipment.
KCC Warning
Messaage
“ 해당무선설비는
해
는 운용 중 전파혼신 가능성이 있으므
므로 인명안전
전과 관련된 서비스는 할 수
없습
습니다.”
“해당 무선설비는
는 운용 중 전파혼신
전
가능성
성이 있음”
NCC Warning Message
低功率電波輻射性
性電機管理辦法
法
第十
十二條 經型式認
認證合格之低功
功率射頻電機，非經許可，公
公司、商號或使
使用者均不得擅
擅自變更頻率、加大
功率
率或變更原設計
計之特性及功能
能。
第十
十四條 低功率射
射頻電機之使用
用不得影響飛航
航安全及干擾合
合法通信；經發
發現有干擾現象
象時，應改善至
至無干
擾時
時方得繼續使用
用。前項合法通
通信，指依電信
信法規定作業之
之無線電通信。低功率射頻電
電機須忍受合法
法通信
或工
工業、科學及醫
醫療用電波輻射
射性電機設備之
之干擾。
EU Compliance Stattement
SZ DJI
D TECHNOLO
OGY CO., LTD. hereby declares that thiss device is in
n compliance with the essential
requ
uirements and other
relevantt provisions of the R&TTE Dirrective.
A cop
py of the EU Deeclaration of Conformity
is av
vailable onlinee at www.dji.co
om/euro‐comp
pliance
EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany
制 造 商：深圳市大疆创新科技有限公司
地 址：深圳市南山区高新南四道18号创维半导体设计大厦西座14层
服务热线：400-700-0303
Manufactured by:
14th floor, West Wing, Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave, Nanshan
District, Shenzhen, Guangdong, China

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2016:06:01 09:15:30+08:00
Create Date                     : 2016:05:23 14:46:02+08:00
Metadata Date                   : 2016:06:01 09:15:30+08:00
Format                          : application/pdf
Title                           : Microsoft Word - user manual.docx
Creator                         : elena
Document ID                     : uuid:f735dce5-6942-4e73-977b-2cc1dc9e1033
Instance ID                     : uuid:ef0fea36-4771-41aa-a550-b5d1afbafd92
Page Count                      : 11
Author                          : elena

EXIF Metadata provided by EXIF.tools