SZZT ELECTRONICS KS8223 Smart wireless pos User Manual
SZZT ELECTRONICS CO.,LTD Smart wireless pos
User Manual
Magneticstripe itself
Warranty:
technology the industry.
Copyright
This User Guide is issues by SZZT Electronics Co Ltd. SZZT
enjoys exclusive rights reserved according to the copyright
law. Without the prior consent of the copyright owner, anyone
can not engage in copying, additions and deletions, excerpts,
copying or imitation of part of the this manual or all.
The contents of this User Guide are only used to describe the
use of the products manufactured by SZZT. About the
contents of this guide, SZZT Electronics Co Ltd works
without any express or implied warranties or guarantee liabili -
ty.
Warning
For any problem or damage caused the accessories which is
not provide by SZZT or approved by SZZT. SZZT will not
take any responsibility. Anyone has no right to modify or
change the product without the consent of the SZZT Electron -
ics Co Ltd.
Due to the update of products, some of the details of this
document may be inconsistent to the product, please in kind
prevail. SZZT Electronics Co Ltd keep the interpretation right
of this document and reserves the right to amend this specifi-
cation without prior notice.
General troubleshooting guidelines:
The following faults are common faults. For the rest of the
failure, please refer to the company after-sales service content
in order to obtain quality service.
1. Blank display
Check whether the power cable is connected to the AC output
port on the POS or not.
Check whether the power adapter's output port is connected to
the POS or not.
2. Printer does not work:
Check whether the printing paper box is closed or not.
Check whether using the appropriate printing paper and is
correctly loaded.
Make sure to use the appropriate paper and install it correctly
on the printer.
3. Magnetic low reading rate
Check whether the magnetic card has been polluted by dirt or
other pollutants. If so, please replace to a new one.
Please use cleaning card to clean the POS's magnetic header.
4. Unable to read IC card
Check whether the IC card is inserted fully into card slots in
the right direction or not.
Check whether there is any dirt or other pollutants on surface
of the metal contact point of IC card. If so, please use cleaning
card to clean the contact point.
5. The network connection failed
Check the network is connected successfully or not.
Check whether the network configuration meets the installa-
tion requirements or not.
6. GPRS communication failed.
Check whether the SIM card is installed correctly or not.
Check whether the SIM card has activated the GPRS service
or not.
Unpacking check
Open the packing to check the POS and accessories as shown
in below.
For the actual packing content, please refer to the packing list.
Precautions
Safety warning
1. Please insert the AC power plug into the corresponding
outlet on the power adapter.
2. Do not use the terminal in any potentially explosives
environment.
3. Non-professional and technical personal do not dismantle
the terminal's power adapter.
4. Changing the battery with wrong model may leads to
explosion.
Safety instructions
1. Avoid installing or using the terminal during thunder and
lightning environment, otherwise user may be in danger of
lightning strikers.
2. Avoiding using the terminal if found any abnormal smell,
overheat or smoke, please shut-down and power-off the
terminal immediately.
Usage specifications
1. During the installation and operation of the terminal, please
make sure only using the standard approved power socket
with stable voltage, avoiding sharing the circuit with
frequently starting and electricity frequently changing equip-
ments.
2. Avoiding any liquid or objects sprinkled into the terminal.
if so, please shut-down the terminal immediately, cut-off the
power, unload the battery, dry the liquid and remove the
objects.
3. Avoiding hard pressing, vibration, shaking and knocking on
the terminal.
4. Operate the terminal in a dry, ventilated and clean environ-
ment, avoiding direct sunlight, keeping the working tempera-
ture at 5-35 centigrade and working humidity at 20%-80%.
5. Maintain the terminal regularly, including: function tests,
whole terminal external cleaning, printer and keypad
cleaning.
6. Using the proper printing paper for the terminal.
7. When there's problem persists after you have followed
troubleshooting guidelines, please contact with SZZT for
after-sales support and further information. do not open and
maintain the POS by yourself.
8. When there's a safety problem, for example abnormal
smell, abnormal noise, electric leakage, etc. please power-off
the terminal immediately and report to the terminal manage-
ment department to solve the problems.
SZZT is not responsible for any operation and behaviors
shown as below:
The operating system only supports official upgrades, if the
user installs unofficial system, the risks and losses resulted in
security will be borne by the user (There may be risks: user
information is stolen, automatically send text messages,
locate your location, etc.)
Terminal damaged by improper operation and maintenance
which did not comply with the user guide's requirements.
Product packing list
1. 1 Mainframe
2. 1 Power adapter
3. 1 Battery
4. 1 User guide
5. 1 Micro USB Cable
6. 1 Thermal printer
7. Others
1. As shown below, please pull up the printing paper box's
cover to open it.
2. Load the printing paper roll into the printing paper box in
the right direction as shown below and leave some blank
paper at the cutter.
3. Close the printing paper
box's cover.
4. Pull out the printing
paper a little bit along with
the cutter and cut the waste
paper by using the cutter.
Note: please make sure to load the printing
paper in correct direction. otherwise it will lead
to printing failed.
Correct paper loading direction Wrong paper loading direction
When using the POS for the first time, you may need to install
PSAM card, SIM card or TF card. please follow the below
instructions to operate:
place the POS on a soft and clean surface to prevent scratch-
ing.
Startup: press the power button until LCD displays logo,
then the POS is ready.
Shut down: Press power button until LCD displays three
modes: Shutdown, Restart, Flight mode, select "Shutdown" to
shutdown POS
2. According to the illustra-
tion to insert SIM and PSAM
card.
This product?s toxic and hazardous substances
name and content of the table
The products that exceed the service life of environmental
protection shall be reclaimed according to the provisions of
the Administrative Measures on the Control of Electronic
Information Products and shall not be discarded at will
O: means that the toxic and hazardous substances in the parts of all homogeneous
materials in the content of SJ/T11363-2006 specified in the limited requirements below.
X: means the toxic and hazardous substances at least in the part of a homogeneous
material in the content of more than SJ/T11363-2006 limit requirements. However, the
content is beyond (by 搙" mark) components because there is no mature Instead of
Warranty:
1. SZZT will provide you with quality after-sales service.
2. If the damage caused by human factors, SZZT will take
repair maintenance costs.
3. Please keep this card, the company will be based on this
warranty.
Contact information:
Headquarters: SZZT Industrial Park, NO.3 Tongguan Road,
Guangming New District, Shenzhen, Guangdong, China.
Zip code: 518132
Customer Service Hotline: +86- 400 8810 888
Fax: +86-755-26490099
Website: www.szzt.com.cn
SZZT Electronics Co., Ltd. reserves the right to interpret the
warranty card.
Connect the output port of the power adapter to the POS
power connector location. Please use the dedicated serial
cable to connect
Magnetic card reader is on the
right side of the POS, please
swipe the magnetic card in a
steady speed and the magnetic
side should be facing the LCD.
IC Card Reader is at bottom of
the POS, please insert the IC
card into the card slot fully and
the chip side should be facing
up.
3. Load the battery and close
the cover.
Note: please make sure the missing angel on
card is in the right direction responding to the
missing angel on card slot.
Note: the magnetic reader and the IC card
reader is easily stained with dirt after use the
POS for a long time, please use the cleaning
magnetic card or IC card to clean the dirt on
time.
Interface connection
Card reader operation instructions
Product Warranty Card
Product Certification
Loading printing paper rollSIM card /Battery/ PSAM card installation instruction
Name of parts
1. Open the battery cover.
Toxic and Hazardous Materials or Elements
Circuit board
components
Head assembly
Equipment Power adapter Battery
Printing paper USB cable User guide
Inspector
contactless card reader
indicator light
touch monitor
IC card reader
cover of printer
camera
camera
magnetic card reader
SIM card
PSAM card
TF card
power port
power button
volume button
SZZT Electronics CO., LTD
SZZT Industrial Park, NO.3 Tongguan Road,
Guangming New District, Shenzhen, Guangdong, China.
Post Code:518132
Contact Number:+86-(0)755-81728888
Email:marketing@szzt.com.cn
Website:Http://www.szzt.com.cn
KS8223 User Guide
Version:V1.0
Product description
Start up/shut down:
Product nameğSmart POS Terminal
Product model: KS8223
KS8223 User Guide
Statement
FCC RF Exposure Information and Statement
This device meets the government's requirements for exposure to radio waves. The guidelines are
based on standards that were developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the
safety of all persons regardless of age or health. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one
gram of tissue for body, and 4 W/kg averaged over ten gram of human's hands. Device types: Smart wireless
pos (FCC ID: 2AL7RKS8223) has also been tested against this SAR limit. SAR information on this and other pad
can be viewed on‐line at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search.
This device was tested simulation typical 5mm for body and 0 mm to hands. To maintain compliance with FCC
RF exposure requirements, use accessories should maintain a separation distance between the user's bodies
mentioned above, the use of belt clips, holsters and similar accessories should not contain metallic components in
its assembly, the use of accessories that do not satisfy these requirements may not comply with FCC RF exposure
requirements, and should be avoided.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.