Sagem Wireless 95V3L GSM 900/1800/1900 MHz Module User Manual

Sagem Wireless GSM 900/1800/1900 MHz Module

OEM Instruction Manual

Download: Sagem Wireless 95V3L GSM 900/1800/1900 MHz Module User Manual
Mirror Download [FCC.gov]Sagem Wireless 95V3L GSM 900/1800/1900 MHz Module User Manual
Document ID486222
Application IDpYVvGAzJVA4x4nYj3lHHTQ==
Document DescriptionOEM Instruction Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize123.52kB (1543988 bits)
Date Submitted2004-11-08 00:00:00
Date Available2004-11-08 00:00:00
Creation Date0000-00-00 00:00:00
Producing SoftwareGNU Ghostscript 7.05
Document Lastmod2004-11-08 08:57:23
Document TitleUntitled Document
Document CreatorWindows NT 4.0


Unit of Saint Christophe
TMO
+$5':$5(
0$69
7287(69(56,216
Réf. : SCT TMO MASV3 SPEC 30
Revision: I
Réf. sec. : 2x xxx xxx – x
Date :
02/11/04
Page 1 sur 46
&2[[;6VSHFLILFDWLRQ
Type of document :
SCT TMO MASV3 SPEC 030 I spec
SPECIFICATIONS
Document
. All rights of reproduction and disclosure reserved.
agrément triband.doc
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this
product without notice.

&RQFOXVLRQRUVXPPDU\:
This document gives an overview of the CO2xx/XS200 module: a miniature, single-side, BGA board, tri-band
GSM/GPRS module, ready for integration in mobile application like vehicle-mounted or vending machines …
It describes the main functionalities of this module as well as the electrical interfaces, the mechanical
specification (dimension, form…) and the electrical specification of the module.
+$5':$5(
&2[[;6VSHFLILFDWLRQ
)RUPRELOHDSSOLFDWLRQV
Ref. :
SCT TMO MASV3 SPEC 30
Ref. Sec.
2x xxx xxx – x
Document
Rev :
02/11/04
. All rights of reproduction and disclosure reserved.
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.

Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
14/09/04
&2;;;6
*60*35675,%$1'%&(02'8/(
)2502%,/($33/,&$7,216
Document
. All rights of reproduction and disclosure reserved.
Page 1
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.

Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
14/09/04
&+$1*(+,6725<
5HY
'DWH
5HDVRQIRUFKDQJH
12/07/03
First document
15/07/03
07/10/03
LCD addressable, electrical specification, vibrating device interface
description, LED interface, audio interface, keyboard interface
modification, melody chip interface description, Blue tooth interface
description
Pinout modification, electrical specification, LED and backlight capability
14/11/03
Pinout Modification, LCD and Keyboard Backlight suppression
27/01/04
Charge precision, VBAT limitation, OEMEM* signal
06/04/04
End of preliminary specification
07/05/04
Power consumption
14/09/04
Pull up / Pull down, certification clarifications
02/11/04
certification clarifications
7$%/(2)&217(176

6&23(

%/2&',$*5$0 







,QWURGXFWLRQ 
5HIHUHQFH  
6WDQGDUGVFRPSOLDQFH  
FRPSOLDQFHZLWKIFFJXLGHOLQHV 
7HUPVDQGDEEUHYLDWLRQ  
3URGXFWIHDWXUHV  
)81&7,21$/'(6&5,37,21 

6,0  

$XGLR 

'LVSOD\  
3.3.1
Serial interface ........................................................................................................................... 13
3.3.2
Parallel interface to LCD ............................................................................................................ 14

'DWD  
3.4.1
Data services.............................................................................................................................. 15
3.4.2
IrDA ............................................................................................................................................ 15
3.4.3
UART 2....................................................................................................................................... 15
3.4.4
V24 ............................................................................................................................................. 15
3.4.5
USB ............................................................................................................................................ 16

$QWHQQD  

.H\SDG 

9LGHRVHQVRU  
3.7.1
I2C interface ............................................................................................................................... 17
3.7.2
Parallel interface to sensor......................................................................................................... 17
Document
. All rights of reproduction and disclosure reserved.
Page 2
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.

Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
14/09/04
([WHUQDOFRPSDQLRQFKLSLQWHUIDFH 

3.8.1
I2S interface ............................................................................................................................... 17
3.8.2
Parallel interface to companion chip .......................................................................................... 17

%OXHWRRWK RSWLRQDO  
3.9.1
MCSI interface............................................................................................................................ 21
3.9.2
UART interface........................................................................................................................... 22
3.9.3
Clock........................................................................................................................................... 22

0HORG\JHQHUDWLRQ  

'$,  

&ORFNV  

3RZHUPDQDJHPHQWDQGFKDUJH 
3.13.1 Battery ........................................................................................................................................ 22
3.13.2 VRIO........................................................................................................................................... 23
3.13.3 Vbackup ..................................................................................................................................... 23
3.13.4 Charge........................................................................................................................................ 23

$FFHVVRULHV  
3.14.1 Flap............................................................................................................................................. 23
3.14.2 Network LED .............................................................................................................................. 23
3.14.3 Vibrating device.......................................................................................................................... 24

23(5$7,1*02'(6

%$//287

0RGHVGHVFULSWLRQ  
4.1.1
No supply ................................................................................................................................... 25
4.1.2
OFF ............................................................................................................................................ 25
4.1.3
Active.......................................................................................................................................... 25
4.1.4
Standby ...................................................................................................................................... 25

7UDQVLWLRQVGHVFULSWLRQ 
4.2.1
Power_on ................................................................................................................................... 25
4.2.2
Power_off ................................................................................................................................... 26
4.2.3
Switch_on................................................................................................................................... 26
4.2.4
Switch_off ................................................................................................................................... 26
4.2.5
Wake up ..................................................................................................................................... 26
























(/(&75,&$/63(&,),&$7,21 
9%$7  
95,2  
'$,LQWHUIDFH 
1HWZRUN/('  
6HULDOLQWHUIDFHIRU/&' 
.H\ERDUGLQWHUIDFH  
9LEUDWLQJGHYLFHFRQWURO 
9  
,5'$DQG8$57  
5HVHW  
6SDUH,2  
&ORFNV  
3DUDOOHOLQWHUIDFHIRUFRPSDQLRQFKLS 
3DUDOOHOLQWHUIDFHIRU/&'  
86%LQWHUIDFH  
00&LQWHUIDFH  
9LGHRVHQVRULQWHUIDFH  
0&6,LQWHUIDFH  
,6LQWHUIDFH 
,&LQWHUIDFH 
-7$*LQWHUIDFH  
$'&  
,QWHUUXSWV  
Document
. All rights of reproduction and disclosure reserved.
Page 3
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.


Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
14/09/04
9%$&.83  

(19,5210(17$/63(&,),&$7,21 

0(&+$1,&$/63(&,),&$7,21 



2SHUDWLQJFRQGLWLRQV  
&OLPDWLFFRQGLWLRQV  
$11(;( 
Document
. All rights of reproduction and disclosure reserved.
Page 4
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 6&23(
 ,1752'8&7,21
This document gives an overview of the CO2xx/XS200 module: a miniature, single-side, BGA board, tri-band
GSM/GPRS module, ready for integration in mobile application like vehicle-mounted or vending machines…
It describes the main functionalities (GPRS / GSM 900MHz / DCS 1800MHz / PCS 1900MHz, interface to a
melody chip, LCD interface, SIM interface, vibrating device interface, audio interfaces for
speaker/microphone or accessories, battery interface, battery charging interface, USB interface, SD card
interface, Sensor interface … ) of this module as well as the electrical interfaces, the mechanical specification
(dimension, form… ) and the electrical specification of the module.
 5()(5(1&(
 67$1'$5'6&203/,$1&(
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
GSM 02.60: "Digital cellular telecommunications system (Phase 2+); Stage 1 Service Description of the
General Packet Radio Service (GPRS)". Version 6.3.0.
GSM 03.03: "Digital cellular telecommunications system (Phase 2+); Numbering, addressing and
identification". Version 6.6.0.
GSM 03.13: "Digital cellular telecommunications system (Phase 2+); Discontinuous Reception (DRX) in
the GSM system". Version 6.0.0.
GSM 03.60: "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service
(GPRS); Service description; Stage 2". Version 6.7.0.
GSM 03.64: "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service
(GPRS);Overall description of GPRS radio Interface; Stage 2". Version 6.4.0.
GSM 04.02: "Digital cellular telecommunications system (Phase 2+); GSM Public Land Mobile Network
(PLMN) access reference configuration". Version 6.0.0.
GSM 04.03: "Digital cellular telecommunications system (Phase 2+); Mobile Station - Base Station
System (MS - BSS) interface Channel structures and access capabilities". Version 6.0.0.
GSM 04.04: "Digital cellular telecommunications system (Phase 2+); Layer 1 General requirements".
Version 6.0.0.
GSM 04.05: "Digital cellular telecommunications system (Phase 2+); Data Link (DL) layer General
aspects". Version 6.0.1.
GSM 04.07: "Digital cellular telecommunications system (Phase 2+); Mobile radio interface signalling
layer 3 General aspects". Version 6.5.1.
GSM 04.08: "Digital cellular telecommunications system (Phase 2+);Mobile radio interface layer 3
specification". Version 6.11.0.
GSM 04.60: "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service
(GPRS); Radio Link Control/Medium Access Control (RLC/MAC) protocol". Version 6.9.0.
GSM 04.64: "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service
(GPRS); Logical Link Control (LLC)". Version 6.7.0.
GSM 04.65: : "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service
(GPRS); Mobile Station (MS) - Serving GPRS Support Node (SGSN); Sub network Dependent
Convergence Protocol (SNDCP)". Version 6.7.0.
GSM 05.02: "Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on
the radio path". Version 6.9.0.
GSM 05.03: "Digital cellular telecommunications system (Phase 2+); Channel coding". Version 6.2.1.
GSM 05.08: "Digital cellular telecommunications system (Phase 2+); Radio subsystem link control".
Version 6.8.0.
Document 
. All rights of reproduction and disclosure reserved.
Page 5
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
DRAFT
• GSM 05.10: "Digital cellular telecommunications system (Phase 2+); Radio subsystem synchronisation".
Version 6.6.0.
• GCF-CC (V.3.12.0) and GT.01.
• NAPRD.03 (V.2.10.1).
 &203/,$1&(:,7+)&&*8,'(/,1(6
Fix-mount and mobile devices incorporating CO2xx/XS200,XS200 modules must be designed to maintain a
minimum separation distance of 20 cm between the antenna and the end user to satisfy RF exposure
requirements for mobile transmitting devices.
 7(506$1'$%%5(9,$7,21
ADC
ADPCM
AFC
ASIC
BMP
CODEC
CTS
DAC
DAI
DCS
DSP
DSR
DTR
EGSM
EMS
ESD
ETS
GSM
GPRS
IC
IEEE
I/O
IRDA
ISO
ITU
JPEG
JTAG
KBPS
LCD
LED
LNA
MBPS
MIDI
MMI
PA
PBCCH
PCB
PCS
PLL
PNG
RAM
RF
RI
Document 
Analog to Digital Converter
Adaptive Delta Pulse Code Modulation
Application Frequency Correction
Application Specific Integrated Circuit
Bitmap
Coder-Decoder
Clear To Send
Digital to Analog Converter
Digital Analog Interface
Digital
Data Signal Processor
Data Set Ready
Data Terminal Ready
Enhanced GSM
Enhanced Messaging Services
Electrostatic Discharge
European Telecommunication Standard
Global Standard for Mobile communication
Global Packet Radio Services
Integrated Circuit
Institute of Electrical and Electronics Engineers
Input / Output
Infra Red
International Standards Organisation
International Telecommunication Union
Joint Picture Expert Group
Joint Test Action Group
Kbit per second
Liquid Crystal Display
Diode
Low Noise Amplifier
Mbit per second
Musical Instrument Digital Interface
Man Machine interface
Power Amplifier
Packet Broadcast Channel
Printed Circuit Board
Personal Communication System
Phase Locked Loop
Portable Network Graphics
Random Access Memory
Radio Frequency
Ring Indication
. All rights of reproduction and disclosure reserved.
Page 6
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
RMS
RTS
RX
SIM
SMS
SRAM
TBC
TBD
TX
UART
USB
USSD
VCO
WAP
WBMP
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
Root Mean Square
Ready To Send
Receive direction
Subscriber Identification Module
Short Message Service
Static Random Access Memory
To Be Confirmed
To Be Defined
Transmit direction
Universal Asynchronous Receiver and Transmitter
Universal Serial Bus
Unstructured Supplementary Service Data
Voltage Controlled Oscillator
Wireless Application Protocol
Wide Bitmap
 352'8&7)($785(6
Temperature range
Weight (in g)
ESD
Physical dimensions
Connection
Power supply
Power consumption
Battery charge management and interface
Antenna connection
Frequency bands
Voice codecs
GSM class
Transmit power
Supported SIM card
SIM slot
Vibrating device
Document 
Normal range: -10°C to +55°C (fully compliant)
Extended range: -20°C to –10°C and +55°C to +70°C
(functional without any risk for the network)
Storage: -40°C to °85°C
10g
ESD protected, < 1kv or 2kv (see application note)
33x38x3.3 mm (typical)
BGA type connection (including antenna and battery
connection)
3.45V to 4.5V range, 3.8V nominal.
Off mode: 80uA (typ)
Standby mode: 2mA (typ)
Communication mode: 260mA (GSM/DCS à Pmax)
2.2A (GSM peak during TX
slot)
Battery charge management is included for regulated
charger to 600mA maximum charge current.
Specific un-regulated charger qualified by SAGEM
could be used (see application note).
No antenna included in the module. Antenna
connection is included in the BGA ball-out. See
recommendations for connection.
EGSM900 + DCS1800 + PCS1900
Half Rate, Full Rate, Enhanced Full Rate
Small MS
Class 4 (2W) for EGSM900
Class 1 (1W) for DCS1800 / PCS1900
3V SIM cards.
To prevent SIM card’s damages, the power supply of
the module has to be turned off before any
manipulation of the SIM card.
Not included on the module. Signals for the
management of the SIM card are provided on ballout.
Not included in the module. Control is provided on
ball-out.
. All rights of reproduction and disclosure reserved.
Page 7
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
Keyboard / LCD backlight / network LED (GB)
Audio up-link
Audio down-link non stereo
Audio down-link stereo
Flap open/closed detection
Keyboard interface
UART1 interface with flow control
IrDA interface or UART2 interface
Data services
Supplementary services
USB interface
Melody chip interface
Serial Interface
Companion chip Interface
LCD parallel interface
MMC interface for SD card only
Video sensor interface
Blue tooth interface (optional)
Reset pin
Power on pin
Document 
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
GB LED management. Interface to external backlight
and RGB component.
2x2 differential inputs are provided for microphone
(accessories and handset).
3x2 differential outputs are provided for non stereo
earphone (accessories and 6 ohms and 32 ohms).
3 outputs are provided for stereo earphone
(accessories and handset).
IO5 dedicated for Flap.
6x6 keyboard interface is provided on ball-out.
Up to 115.2 Kbaud with auto bauding.
Full flow control signals (+2.8V) are provided on ballout.
If a full compliant RS232 (+/-5V) serial interface is
needed:
The drivers (like MAX3232, ST3237CD, … ) are not
included in the module and have to be added on the
main PCB.
A proven schematic to build the RS232 interface is
provided in application note.
Up to 115.2 Kbaud.
UART2 and IrDA are not multiplexed but could not be
used at the same time.
GPRS, CSD, Fax
Line identification, Call Waiting, Call Hold, Call
Forwarding, Multiparty, Closed User Group, Call
Barring, Advice of Charge, USSD
USB 1.1 (slave only) is provided on ball-out.
The melody chip is not integrated in the module but
the interface is provided (power supply, clock, analog
audio, serial link, I2S) on ball-out.
A serial interface is provided on ball-out in order to
manage an external LCD or a chip melody.
A parallel interface (16 bits) is provided on ball-out (3
addresses, 1 chip select, OE and RW signals are
available) to connect external companion chip for
additional multimedia application.
A parallel interface (8bits) is provided on ball-out (2
chip select, RW, RS, ESTRB, RESET) to connect
LCDs up to 256K colours.
MMC interface is available on ball-out (power supply
not provided) for SD card only.
Video sensor interface is provided on ball-out
(parallel interface with 8 bit, clock in, clock out,
horizontal synchronisation, vertical synchronisation,
reset, standby, I2C interface) to connect VGA sensor
(power supply not provided).
Blue tooth chipset not included in the module but the
interface (MCSI, Clock 26MHz and UART) is
available on ball-out. Blue tooth chipset management
is optional.
Active high signal available (reset of all the system
including backup).
Available
. All rights of reproduction and disclosure reserved.
Page 8
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.

DRAFT
General purpose I/Os pin
GPRS
GSM/DCS certification GCF-CC
PCS certification
Multimedia objects download
Document 
Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
4 I/O available on ball-out.
SMG 31bis, Multi slot class 10, class B terminal,
PBCCH support
V.3.12.0 and GT.01
NAPRD.03 (V.2.10.1)
Ring tones, wallpapers, icons, games, screen savers
. All rights of reproduction and disclosure reserved.
Page 9
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 %/2&',$*5$0
Antenna
&2[[;6;6PRGXOH
Network LED
Vibrating device
Serial interface to LCD or
melody chip
Parallel interface (16bits)
to companion chip
Parallel interface
(8bits) to LCD
22
14
14
MMC interface
SIM interface (3V)
V24
GPRS / GSM900 / DCS1800 /
PCS1900
Sensor interface
Serial link 2 or IRDA
interface
13
10
USB interface
Bluetooth interface
(MCSI) -optional
I2S interface
Keyboard
Battery charger
Battery (3.8V)
Earphone 32 ohms
Microphone (accessory)
Stereo earphone
Spare I/Os
Interruption Inputs
Backup
Earphone 6 ohms min
)LJXUH
&2[[;6;6EORFGLDJUDP
See Ball-out chapter for more details.
 )81&7,21$/'(6&5,37,21
 6,0
The SIM Card interface is compatible with the ISO 7816-3 IC card standard on the issues required by the
GSM 11.11 Phase 2+ standard. The module also supports Release 99 of the SIM Toolkit recommendation
and supports a Fixed Dialling Number directory.
The SIM Card interface insures the detection (SIMCD), the power on (SIMVCC) of the SIM Card and the
communication with it through a data signal (SIMIO), a clock signal (SIMCLK) and a reset signal (SIMRST).
Document 
. All rights of reproduction and disclosure reserved.
Page 10
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
6LJQDO
SIMRST
SIMCLK
SIMIO
SIMVCC
SIMCD
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
'HVFULSWLRQ
SIM reset, provided by Base-band processor
SIM clock, provided by Base-band processor
SIM serial data line, input and output
SIM supply voltage
SIM insertion detection
3LQ1ƒ
T8
T9
T10
T7
B12
SIM card connection:
&2[[;6
SIMVCC
SIMIO
SIMRST
SIMCLK
SIMCD
SIM card
In option
)LJXUH
6,0FRQQHFWLRQ
The SIMCD signal should be connected to the SIM card reader in order to get SIMCD at low level (GND)
when no card is present and at high level (SIMVCC) when card is present (external pull down needed when
SIM card connector with detection is used).
This interface includes main protections.
Document 
. All rights of reproduction and disclosure reserved.
Page 11
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 $8',2
The module supports the following voice codecs:
• Half-Rate
• Full-Rate
• Enhanced Full Rate
It manages an external handset microphone (MICIP/MICIN) and an external handset earphone (32 ohms
HPP32/HPN32 and 6 ohms HPP8/HPN8) in differential mode.
The bias voltage of the microphone is provided directly on MICIP/MICIN pins (1.5V).
There are two options for the earphone:
- Two earphones, one 32 Ohms as earpiece and one 6 Ohms minimum as Ring/melody and as handsfree loudspeaker if it is far from the microphone.
- one 32 Ohms earphone as earpiece.
The module can also manage accessories (earphone and microphone) through dedicated lines
(HSMICIP/HSMICIN for microphone and HSOL/HSGND/HSOR for stereo earphone). The typical impedance
for the earphone is 150ohms.
Base-band
Ampli+Filter
MICIP
MICIN
HSMICIP
HSMICINP
HPP32
HPN32
HPP8
HPN8
HSOL
HSGND
HSOR
)LJXUH
$XGLR
This interface includes main protections.
To ensure proper operation of such sensitive signals, they have to be isolated from the other by ground on
mother board layout.
NB: To avoid destruction of module components, the HP inductance has to be 47nH +/- 5% @ 200MHz
Document 
. All rights of reproduction and disclosure reserved.
Page 12
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 ',63/$<
 6HULDOLQWHUIDFH
A serial interface is provided on the module to manage an external LCD (256 colours) through data input
signal (DIMIW), data output signal (DOMIW), clock (CKMIW) and chip select (CSMIW1*).
Power supply of the LCD (VRIO) is also provided through this interface.
This interface could be used to manage one serial LCD or one melody chip (or other chipset using this
interface).
)LJXUH
6HULDOOLQNUHFHLYHWLPLQJ
)LJXUH
6HULDOOLQNWUDQVPLWWLPLQJ
7LPLQJ
Tw(SCLK)
Tc(SCLK)
Td(SDO)
Th(SDO)
Tw(nSCSx)
Td(nSCSx)
Ts(SDI)
Th(SDI)
Ts(nSCSx)
Th(nSCSx)
'HVFULSWLRQ
Pulse duration, serial port clock
Cycle time, serial port clock
Delay time, data valid after CLK falling
Hold time, data valid after CLK falling
Pulse duration, EN port
Delay time, En after CLk rising
Setup, data valid before CLK rising
Hold time, data valid after CLK rising
Setup, data valid before CLK falling
Hold time, EN after CLK falling edge
0LQ QV 
38
77
38
10
15
15
10
10
0D[ QV 
10
This interface includes main protections.
Document 
. All rights of reproduction and disclosure reserved.
Page 13
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
DRAFT
If specific LCD driver is used, the software would be provided by SAGEM, or at least the specific drivers will
be integrated by SAGEM. In that case a specific quotation is required.
 3DUDOOHOLQWHUIDFHWR/&'
A parallel interface is provided on the module to manage an external LCD (up to 262K colours) with data bus
(DLCD<0..7>), strobe enable (ESTRLCD), RWLCD*, RSLCD*, reset (RESETLCD*) and 2 chip select
(CS1LCD*, CS0LCD*).
NB: 65K and 262K colour LCDs have to be configured in 8 bits multi access mode.
)LJXUH
5HDGWLPLQJ LQPRGH 
)LJXUH
:ULWHWLPLQJ LQPRGH 
7LPLQJ
Tw(LCD)
'HVFULSWLRQ
Pulse duration
Document 
0LQ QV 
38
. All rights of reproduction and disclosure reserved.
0D[ QV 
Page 14
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
Tcyc
Tacc1
Tacc2
Tod1
Tod2
Tdacc
Tdod
Tds
Tdh
Cycle time
Access time of RnW
Access time off RS, nCS
Output delay of RnW
Output delay of RS, nCS
Data access time
Data output disable time
Setup time of read data
Hold time of read data
77
38
10
15
15
10
10
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
10
 '$7$
 'DWDVHUYLFHV
The module supports the following services:
• GPRS
• CSD: transparent and non-transparent up to 9600 BPS
• fax: class 1
Data sessions may be established over the main serial link, using the IrDA port (see below) or though the
USB interface.
 ,U'$
This UART interface is compatible with 16C750 compliant devices. It includes the slow infra-red protocol in
order to be connected with an infra-red transmitter to any external data peripherals with an IrDA compliant
data interface.
This IrDA interface (TXIR, RXIR and CMDIRDA) provided by the module is compliant with the IrDA 1.0 SIR
up to 115.2 Kbaud.
This interface could not be used at the same time as UART2 interface.
This interface includes main protections.
 8$57
It is strongly recommended to leave this interface externally accessible for Debug.
This interface could not be used at the same time as IRDA interface.
 9
A V24 interface is provided on external pins of the module with the following signals:
- RTS/CTS
- RX/TX
- DSR
- DTR
- DCD
- RI
It supports speeds up to 115.2 KBPS and may be used in auto bauding mode.
This interface includes main protections.
Document 
. All rights of reproduction and disclosure reserved.
Page 15
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 86%
CO2xx/XS200/XS200 provides an USB 1.1, slave only, with the following signals: differential data (USB_DP,
USB_DM) and +5V input power supply (VCUSB).
 $17(11$
The antenna connexion is prived through the ’antenna’ ball. This is a 50ohm RF connexion and as such must
be connected to the antenna via a proper 50ohm line; the RF ground is provided by the 5 balls surrounding
the antenna ball. A matching network might be required between the module antenna connexion and the
actual antenna to further adapt the antenna impedance to the module. An example of connexion is provided
in the application note together with some layout guidelines.
 .(<3$'
A 6X6 keyboard could be managed by the module through the R1/R2/R3/R4/R5:R6 row signals and
C1/C2/C3/C4/C5:C6 column signals.
OUI signal performs the ON function. OFF signals performs OFF function.
Multi-key pressing is possible with this keyboard configuration.
GREEN
GND
NC
NC
CL
NC
NC
NC
NC
NC
NC
NC
NC
NC
MN
P1
P2
DO
LEFT
OK
P3
LAT.
HIGH
LAT.
RIGHT
UP
RED
R1
R2
LOW
R3
R4
&2[[
R5
R6
C6
C5
C4
C3
C2
C1
)LJXUH
Keyboard connection
NC = these keys are connected internally in the CO2xx/XS200/XS200 module but are not managed.
The module uses the Tegic T9
TM
predictive input system.
 9,'(26(1625
All the interfaces to connect a VGA video sensor are provided. Only power supply is not included.
Document 
. All rights of reproduction and disclosure reserved.
Page 16
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 ,&LQWHUIDFH
A standard I2c interface is available on ball-out to send command to the video sensor.
 3DUDOOHOLQWHUIDFHWRVHQVRU
A dedicated parallel interface is provided on ball-out with 8 bits data bus (DCAM<0..7>), vertical
synchronisation (VSCAM), horizontal synchronisation (HREF), input clock (PCLKCAM), configurable output
clock (XCLKCAM), reset (RESETCAM), standby (STBYCAM).
 (;7(51$/&203$1,21&+,3,17(5)$&(
 ,6LQWHUIDFH
For audio transfer:
)LJXUH
,6WLPLQJ
7LPLQJ
Tw(CSCLK)
Tc(CSCLK)
Td(CDO)
Th(CDO)
Ts(CDI)
Th(CDI)
Td(CSYNC)
Th(CSYNC)
'HVFULSWLRQ
Pulse duration
Cycle time
Delay time, data after CLK rising
Hold time, data valid after CLK rising
Setup, data valid before CLK falling
Hold time, data valid after CLK falling
Delay time, EN after CLK falling
Hold time, EN after CLK falling
0LQ QV 
651
1302
0D[ QV 
15
 3DUDOOHOLQWHUIDFHWRFRPSDQLRQFKLS
A parallel interface is provided on ball-out. This interface include 16 bits data lines (DPROC<0..15>), 3
address lines (APROC<1>, APROC<2>, APROC<3>), Write control signal RWPROC* (active low), Read
control signal OEPROC* (active low) and one chip select CS1PROC* (active low). This interface is dedicated
to external companion chip interface (as external DSP for additional multimedia applications).
This interface supports page mode.
Document 
. All rights of reproduction and disclosure reserved.
Page 17
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
DRAFT
NB: The maximum capacitance acceptable on each signal of the parallel interface is 25pF (including copper
line capacitance, connectors capacitance… ).
Document 
. All rights of reproduction and disclosure reserved.
Page 18
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
)LJXUH
Parallel link read timing
)LJXUH
Parallel link write timing
Document 
. All rights of reproduction and disclosure reserved.
Page 19
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
Single access:
'HVFULSWLRQ
7LPLQJ
CPU frequency
tcyc
Chip Select Valid
tcsv
NCS to Address valid
tda
Address hold from nCS
tha
NBHE, nBLE to nCS
tdbe
NOE to nCS
tdoe
Input data setup to nCS
tsu
Input data hold from nCS
tho
NCS to RnW
tsrw
RnW to nCS
tdrw
NCS to output data valid
tdso
Output data hold from RnW
thd
N= Wait State number
0LQ QV 
tcyc
5.5
Tcyc/2-tdrw
1.3
0D[ QV 
1/Fcpu
(N+1)tcyc
1.2
0.6
0.6
2.9
Tsrw+7.5
Page mode access:
'HVFULSWLRQ
7LPLQJ
CPU frequency
tcyc
Chip Select Valid
tcsv
NCS to Address valid
tda
Address hold from nCS
tha
NBHE, nBLE to nCS
tdbe
NOE to nCS
tdoe
Input data setup to nCS
tsu1
Input data hold from nCS
tho1
Input data setup to nCS
tsu2
tho2
Address invalid time
Tsa1sa2
Input data hold from nCS
Note: all timings computed for an external capacitance load of 10pF
0LQ QV 
tcyc
5.2
5.6
0D[ QV 
1/Fcpu
(N+1)tcyc
1.5
0.8
1.5
NB: if needed, additional Wait State could be added by SAGEM.
%HFDUHIXOWKHPD[LPXPFDSDFLWDQFH FRPSRQHQWVOLQHVFRQQHFWRUV« 
DFFHSWDEOHRQHDFKVLJQDORIWKHSDUDOOHOEXVLVS)
Document 
. All rights of reproduction and disclosure reserved.
Page 20
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 %/8(7227+ 237,21$/ 
All the interfaces to connect a blue tooth chipset are provided. Only power supply is not included.
Blue tooth chipset management is optional.
 0&6,LQWHUIDFH
For audio transfer:
)LJXUH
%OXHWRRWKUHFHLYHWLPLQJ
)LJXUH
%OXHWRRWKWUDQVPLWWLPLQJ
7LPLQJ
Tw(MCSI_CLK)
Tc(MCSICLK)
Td(MCSI_DO)
Th(MCSI_DO)
Td(MCSI_FSYNCH)
Tw(MCSI_FSYNCH)
Ts(MCSI_DI)
Th(MCSI_DI)
Ts(MCSI_FSYNCH)
Th(MCSI_FSYNCH)
'HVFULSWLRQ
Pulse duration
Cycle time
Delay time, data after CLK rising
Hold time, data valid after CLK rising
Delay time, EN after CLK falling
Pulse duration, EN after CLK falling
Setup, data valid before CLK falling
Hold time, data valid after CLK falling
Setup time, EN after CLK falling
Hold time, EN after CLK falling
Document 
0LQ QV 
77
154
77
15
15
10
10
. All rights of reproduction and disclosure reserved.
0D[ QV 
10
10
Page 21
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 8$57LQWHUIDFH
See UART interface from the V24 interface or from the IRDA interface.
 &ORFN
26MHz clock could be used for clock input of blue tooth component (please note: 13MHz clock is also
available on CO2xx/XS200 ball-out but is not compliant with blue tooth chipsets features).
 0(/2'<*(1(5$7,21
An external melody chip could be connected to the CO2xx/XS200 module through the following links:
- I2S for audio transfer
- Microwire for command
- 13MHz for melody chip clocking
Please note: if the melody chip is connected to the microwire, no serial LCD could be connected.
All these interfaces are described in the previous chapters.
 '$,
A DAI interface is provided on the module for type approval tests.
 &/2&.6
A 32KHz frequency clock, a 13MHz frequency digital clock and a 26MHz frequency analogic clock are
provided on external pins of the module.
The 13MHz clock could be used for the melody chip.
The 26MHz clock could be used for the blue tooth interface.
To ensure proper operation of such sensitive signals, they have to be isolated from the other by ground on
mother board layout.
 32:(50$1$*(0(17$1'&+$5*(
 %DWWHU\
The power supply signal VBAT is 3.45V to 4.5V range and 3.8V nominal.
Only Li-Ion battery are supported.
It has to be more than 3.2V, even during transients in order to avoid unwanted resets. The power supply
dropout has to be limited to 450mV, when the current consumption goes from minimum to maximum (0.1 to
2A). The noise level of the power supply has to be limited to 50mV RMS in the 100MHz – 1MHz frequency
range
SAGEM advises to use Sanyo or LG battery. If battery is used, SAGEM agreement is needed (slight
qualification tests).
Only battery with 200mohms maximum internal resistor are managed by the module.
External capacitor of 47uF has to be added as near as possible from the battery connector of mother board
for charge needs.
Document 
. All rights of reproduction and disclosure reserved.
Page 22
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 95,2
+2.8V output is available on external pin of the module and could supply +2.8V external components (current
capability 10mA in active mode).
This interface includes main protections.
 9EDFNXS
External Backup could be supply through the VBACKUP input (from 2.2V to 3.2V). A internal mechanism is
present to charge the backup battery.
If No external Backup is supplied, VBACKUP input has to be connected to VBAT signal.
 &KDUJH
This interface manages the charge of the mobile for regulated charger, when a charger is connected, even in
the following conditions: deeply discharged battery, short-circuited battery and unconnected battery (600mA
with regulated charger).
The interface manages the charge of some un regulated chargers, that have to be qualified by SAGEM (see
listing in application note).
This interface includes main protections.
 $&&(6625,(6
Accessories connection has to be defined more precisely.
With the CO2xx/XS200 module, the following accessories could be connected :
- a pedestrian stereo or non stereo hand-free kit
- a battery charger
- an automotive hand-free kit
- a data cable
- an USB cable
These interfaces includes main protections.
 )ODS
IO5 is dedicated for Flap detection.
 1HWZRUN/('
Commands for Green and Red LED are provided.
LEDR or
LEDG
)LJXUH
/('GHYLFHFRQQHFWLRQ
Document 
. All rights of reproduction and disclosure reserved.
Page 23
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 9LEUDWLQJGHYLFH
Vibrating device control is provided but external transistor is needed.
VBAT
VIB+
VIB-
CMDVIB
)LJXUH
9LEUDWLQJGHYLFHFRQQHFWLRQ
Document 
. All rights of reproduction and disclosure reserved.
Page 24
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 23(5$7,1*02'(6
Power_off
No supply
Power_on
Standby
Power_off
OFF
Wake-up
Switch_off
Switch_on
Active
Sleep (automatic)
Switch_off
)LJXUH
2SHUDWLQJPRGHVVWDWHGLDJUDP
 02'(6'(6&5,37,21
 1RVXSSO\
VBAT < 3.2V and VBACKUP < 2.2V.
All functions and power supplies are OFF: VRIO = 0.
 2))
VBAT > 3.2V or external Backup VBACKUP > 2.2V.
The RTC only is running (32kHz). All other functions and power supplies are OFF: VRIO = 0.
 $FWLYH
The module is active: all the functions are running and all the power supplies are ON and in full power mode
(full consumption).
VRIO = +2.8V
 6WDQGE\
The module is in standby mode: the power supplies are ON and in low power mode.
This mode is typically use when the module is connected to the network and checking periodically if there is
an incoming call.
 75$16,7,216'(6&5,37,21
 3RZHUBRQ
A battery is connected to the module with VBAT > 3.2V (and/or VBACKUP is switched ON).
Document 
. All rights of reproduction and disclosure reserved.
Page 25
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 3RZHUBRII
The battery is removed from the module (and/or VBACKUP is switched OFF).
 6ZLWFKBRQ
The battery is already connected. The module starts when ON key is pressed or a charger is connected or
when wake up occurs.
 6ZLWFKBRII
The battery is connected. The software is turning off of the module when OFF key is pressed and VBAT >
3.2V.
 :DNHXS
The actions to go from standby mode to active mode are:
- Charger connection
- Key pressed
- Incoming call
- Data cable connection
- V24 activity
Document 
. All rights of reproduction and disclosure reserved.
Page 26
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 %$//287
The following list of signals could change.




$
%
GND
&
GND DCAM
<1>















GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
TXD1
TXIR
RXD1 TXD2 RXD2
CTS
'
GND
DTR
RTS
( GND
DCD
DSR
RENA
ND
GND
C<1>
OC*
OUI* SDAI2 SIMC
POW CDMM DMMC DMMC DMMC EMU1* GND
MMC
<1>
<2>
<3>
DCAM CMDI DCAM DCAM PCLK SCLI2 CMDM MCSI TDIDI XCLK
<4>
RDA
<2>
<6>
CAM
MC
DI
GIT
CAM
DCAM ALEN
AND
<7>
GND
GND
TSPA EMU0* GND
CTEX
BSCA TDODI GND GND
GIT
N*
RXIR RBNA CLEN DCAM CLKM DMMC MCSI
DO
<0>
MC
<0>
AND
ND*
GND
GND
CE1N MCSIS GND DCAM MCSI
CLK
<3>
AND YNCH
GND
GND
GND
GND
IO11
GND
GND
GND
) GND APRO APRO APRO OEPR CSPR GND




GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND DCAM GND
<5>
GND
GND
GND
GND
GND
GND
GND
VBAT VBAT VBAT VBAT VBAT
GND
GND
GND
GND
GND
GND
GND
GND
GND
DLCD
<4>
GND
VBAT VBAT
GND
GND
GND
+ GND DPRO DPRO DPRO GND INTI2C GND
CS1L
CD*
GND
GND
GND
GND
WP1N CS0L
ANDL CD*
GND
DLCD
<6>
GND
GND
GND
VBAT VBAT
GND
GND
GND
GND
GND WENA GND
ND
GND
DLCD DLCD ESTR DLCD RSLC
<3>
<0> BLCD <7>
GND
GND
GND
GND
GND
GND
ANTE
NNE
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
. GND DPRO DPRO DPRO DPRO GND
GND RWLC GND
D*
GND
GND
GND
GND
GND
GND
DLCD
<5>
GND
GND
GND
GND
GND
GND
GND
GND
/ NC
CRES GND
ET
GND
GND
GND
GND
C5
R5
C1
DLCD
<2>
GND
GND
GND
GND
GND
GND
GND
0 GND DAIIN DAIOU DAIRS STBY VCCS GND
GND CLK13
CDO
GND
GND
GND
C4
C6
R6
C2
GND
GND
GND
GND
GND
1 GND RESE
CMDV GND
IB
GND
GND
HPN8 HPP32 HSGN GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
HPP8 HPN3
GND
GND
GND
GND
GND
C<3>
C<2>
* GND DPRO DPRO DPRO GND
C<15> C<14> C<13>
OC1*
GND
C<10> C<11> C<12>
, GND DPRO DPRO DPRO RWPR GND
C<9>
C<8>
C<7>
C<4>
C<5>
C<6>
C<3>
C<2>
C<1>
- GND DPRO DPRO DPRO
IO7
C<0>
DAICL RESE HREF VSCA LEDC
TCAM CAM
TLCDL
NC
CAM
IO6
IO5
RI
ITDAT GND
CHAR CHAR CHAR GND
GEUR GEUR GEUR
Document
GND
C3
GND HSOR HSOL HSMI
CIP
. All rights of reproduction and disclosure reserved.
USB_ USB_ DLCD
DP
DM
<1>
CDI
R1
GND
2 GND
OC*
Page 27
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
NC
TEST VBAC
RST KUP
4 GND LEDG INT1 VRIO ADC2
5
6
7
8
GND
CSMI ENLE
W2*
GND
NC
DOMI CKMI
GND
TDOA
NALO
NC
GND
GND
GND
GND
GND
GND
GND
HSMI
CIN
GND
CSYN CSCL
GND
GND
GND
GND
GND
MICIN GND
GND CLK32 GND TDIAN GND
ALO
GND
GND
GND
GND
MICIP
CSMI
W1*
GND
GND
GND
GND
TCK
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND DIMIW GND SIMVC SIMRS SIMCL SIMIO
GND
Document
GND
GND
GND
GND
GND
. All rights of reproduction and disclosure reserved.
R3
R2
GND
GND
GND
GND
GND
R4
GND
GND
GND
TSPC
LK
GND
GND
GND
GND
GND TSPDI TSPE
NI*
GND
GND
GND
GND
GND
GND
TMS
VCUS
GND
GND
GND CLK26 GND
GND
GND
GND
GND
GND
DRAFT
3 GND LEDR
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
Page 28
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without notice.
GND
TSPD
GND
GND
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
6LJQDOQDPH
DAIRST
DAIOUT
DAIIN
DAICLK
DIMIW
DOMIW
CKMIW
CSMIW1*
CSMIW2*
,2W\SH
Input
Output
Input
Input
Input
Output
Output
Output
Output
ENLED
Output
LEDR
LEDG
R1
R2
R3
R4
R5
R6
C6
C5
C4
C3
C2
C1
OUI*
SIMVCC
SIMRST
SIMCLK
SIMIO
SIMCD
HSMICIP
HSMICIN
Output
Output
Input
Input
Input
Input
Input
Input
Output
Output
Output
Output
Output
Output
Input
Output
Output
Output
In/output
Input
Input
Input
HSOL
HSGND
HSOR
MICIP
MICIN
HPP32
HPN32
HPP8
HPN8
CMDVIB
Output
Output
Output
Input
Input
Output
Output
Output
Output
Output
RI
DSR
Output
Output
Document 
)XQFWLRQ
DAI interface
Serial interface to
connect LCD or chip
melody (1 chip select)
Serial interface for
LED chipset
LED Chipset
command
Red LED command
Green LED comment
Keyboard interface
ON key
SIM interface
To external
microphone
(accessory)
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
'HVFULSWLRQ
DAI reset
DAI output data
DAI input data
DAI clock
LCD driver input data of the serial link
LCD driver output data of the serial link
LCD driver clock of the serial link
LCD driver chip select of the serial link
Chip select for Baklight component
3LQ1ƒ
M4
M3
M2
L2
T5
S4
S5
S6
R3
Enable for Backlight component
R4
Keyboard row 1
Keyboard row 2
Keyboard row 3
Keyboard row 4
Keyboard row 5
Keyboard row 6
Keyboard column 6
Keyboard column 5
Keyboard column 4
Keyboard column 3
Keyboard column 2
Keyboard column 1
Keyboard ON key
SIM power supply
SIM reset
SIM clock
SIM data
SIM insertion detection
Differential input from microphone
Differential input from microphone
P2
Q2
O17
P17
P16
Q17
L14
M15
M14
L13
M13
M12
M16
L15
B10
T7
T8
T9
T10
B12
O15
P14
Differential input to handset microphone
Differential input to handset microphone
Differential output to 32ohms earphone
Differential output to 32ohms earphone
Differential output to 8ohms earphone
Differential output to 8ohms earphone
Vibrating device command
O14
N12
O13
R15
Q15
N11
O11
O10
N10
M17
Ring Indicator
Data Send Ready
N5
E3
To external stereo HP
(accessory)
Microphone interface
Earphone interface
Vibrating device
interface
V24 interface with
flow control
. All rights of reproduction and disclosure reserved.
Page 29
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
DCD
DTR
CTS
RTS
TXD1
RXD1
TXD2
RXD2
TXIR
RXIR
CMDIRDA
INT1
SCLI2C
SDAI2C
INTI2C
CHARGEUR
VCCS
LEDC
TESTRST
ITDATA
DPROC<0>
DPROC<1>
DPROC<2>
DPROC<3>
DPROC<4>
DPROC<5>
DPROC<6>
DPROC<7>
DPROC<8>
DPROC<9>
DPROC<10>
DPROC<11>
DPROC<12>
DPROC<13>
DPROC<14>
DPROC<15>
RWPROC*
OEPROC*
CSPROC1*
APROC<1>
APROC<2>
APROC<3>
DLCD<0>
DLCD<1>
DLCD<2>
DLCD<3>
DLCD<4>
DLCD<5>
Output
Input
Output
Input
Output
Input
Output
Input
Output
Input
Output
Input
Output
In/out
Output
Input
Input
Output
Input
Input
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
Output
Output
Output
Output
Output
Output
In/output
In/output
In/output
In/output
In/output
In/output
Document 
UART interface
IRDA interface
Interrupt
I2C interface
Load interface
Reset
Accessories detection
Parallel interface
For
Companion chip
connection
Parallel
LCD interface
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
Data Carrier Detect
Data Terminal Ready
Clear To Send
Request To Send
UART transmit 1
UART receive 1
UART transmit 2
UART receive 2
IRDA transmit
IRDA receive
IRDA command
Clock
Data
Interrupt
Charge
LED connection for charge activity
Reset system signal
Interrupt signal
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Write
Read
Chip select 1
Address bus
Address bus
Address bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
. All rights of reproduction and disclosure reserved.
E2
D3
C5
D4
B5
B7
B8
B9
B6
D7
C7
Q3
C11
B11
H6
O3,O4,O5
M6
L6
P4
N6
K5
K4
K3
K2
J2
J3
J4
I4
I3
I2
H2
H3
H4
G4
G3
G2
I5
F5
F6
F4
F3
F2
I13
N18
L16
I12
G17
K15
Page 30
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
DLCD<6>
DLCD<7>
ESTRBLCD
CS0LCD*
CS1LCD*
RSLCD*
RWLCD*
RESETLCD*
USB_DP
USB_DM
VCUSB
TSPACTEXT
CSYNC
CSCLK
CDI
CDO
CRESET
DCAM<0>
DCAM<1>
DCAM<2>
DCAM<3>
DCAM<4>
DCAM<5>
DCAM<6>
DCAM<7>
RESETCAM
STBYCAM
PCLKCAM
VSCAM
HREFCAM
XCLKCAM
WP1NAND*
WENAND
RENAND
CLENAND
ALENAND
RBNAND*
CE1NAND
DMMC<0>
DMMC<1>
DMMC<2>
DMMC<3>
CLKMMC
CMDMMC
POWMMC
CDMMC
CLK26M
CLK13M
In/output
In/output
Output
Output
Output
Output
Output
Output
In/output
In/output
Input
Output
In/output
In/output
Input
Output
Output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
In/output
Output
Output
Input
Output
Output
Output
Output
Output
Output
Output
Output
Input
Output
In/output
In/output
In/output
In/output
Output
In/output
Output
Input
Output
Output
Document 
USB interface
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
Data bus
Data bus
Strobe enable
Chip select 0
Chip select 1
LCD register selection (data/control)
Read/write
Reset
Differential data
Power supply input
Radio signal
I2S
Sensor interface
Synchronisation
Clock
Data input
Data output
Reset
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Reset
Standby
Clock input
Clock output
Horizontal synchronisation
Vertical synchronisation
Specific interface
MMC interface
Clocks
Data bus
Data bus
Data bus
Data bus
Clock
Control
Power supply control
Card detect
26MHz analog clock output
13MHz digital clock output
. All rights of reproduction and disclosure reserved.
H15
I15
I14
H13
G12
I16
J16
N2
N16
N17
T15
C17
Q8
Q9
O16
M8
K12
D10
C4
C8
E11
C6
F10
C9
D5
L3
M5
C10
L5
L4
C15
H12
I9
E4
D9
D6
D8
E8
D12
B15
B16
B17
D11
C12
B13
B14
T19
L12
Page 31
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
CLK32K
ADC2
MCSIDI
MCSIDO
MCSICLK
MCSISYNCH
IO5
IO6
IO7
IO11
VBAT
Output
Input
Input
Output
In/output
In/output
In/output
In/output
In/output
In/output
Input
VRIO
VBACKUP
GND
ANTENNE
TCK
TMS
TDIDIGIT
TDODIGIT
TDIANALOG
TDOANALOG
BSCAN*
EMU0*
EMU1*
NC
Output
Input
Ground
Output/input
Input
Input
Input
Output
Input
Output
Input
Output
Output
NC
Document 
ADC
MCSI interface
Power supply
Ground
Antenna input/output
JTAG interface
Boundary scan
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
32KHz digital clock output
Battery type detection
Data input
Data output
Clock SPI
Synchronisation
With Pull down
With pull down
With pull down
With pull up
+3.6V battery power supply
+2.8V output power supply
Backup input
GND
Antenna connection (50 ohms)
JTAG
JTAG
JTAG
JTAG
JTAG
JTAG
JTAG
For debug
For debug
No connect
. All rights of reproduction and disclosure reserved.
R7
Q5
C13
D13
E12
E9
N4
N3
J5
E17
F19,F20,F21,
F22,F23,G19,
G20,H19,H20
Q4
P5
Other
I23
T11
T14
C14
D17
R9
P7
D16
C18
B18
Q21,R21,R20
,S20, L1, P3,
Q6, R5, O2
Page 32
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product
without notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 (/(&75,&$/63(&,),&$7,21
VOH
VOL
VIH
VIL
High level output voltage
Low level output voltage
High level input voltage
Low level input voltage
 9%$7
The module is supplied through the VBAT signal with the following characteristics:
0D[
7\S
0LQ
1DPH
3DUDPHWHU
DC
4.615
4.614
VbatTe (*)
VBAT period (ms)
VBAT period
550
VbatTi (*)
VBAT low duration
(us)
VBAT rise time (us) VbatTr (*)
VBAT fall time (us) VbatTf (*)
4.5
VbatMax (*)
VBAT maximum
voltage (V)
3.45
VbatMin (*)
VBAT minimum
voltage (V)
450 (**)
VBAT drop voltage DeltaVbat (*)
(mV)
Transient voltage
(V)
50mV
Noise level (Vrms)
@100MHz-1MHz
(*): cf figure 16.
(**): for a new battery. Of course for an old battery, this value will be higher and will create a reset (without MMI
message) when the battery begins to be discharged.
)LJXUH
9%$7YROWDJHZDYHIRUP
Document 
. All rights of reproduction and disclosure reserved.
Page 33
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
 95,2
0LQ
7\S
0D[
2.70V
2.80V
2.90V
2.70V
2.80V
3.00V
10mA
0.5mA
10µs
6LJQDO
Voltage level (activ
mode)
Voltage level (sleep
mode)
Current capability
Active mode
Current capability
Sleep mode
Rise time
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
5HPDUNV
 '$,,17(5)$&(
DAIRST, DAIIN, DAICLK and DAIOUT have the following characteristics:
5HPDUNV
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
+3.2
+2.03
+0.8
-0.5
DAIRST
PD 100K
+3.2
+2.03
+0.8
-0.5
DAICLK
PD 100K
+3.2
+2.03
+0.8
-0.5
DAIIN
+2.32
+0.59
DAIOUT
 1(7:25./('
6LJQDO
9  9 
LEDR, LEDG
LEDG: Imax = 2mA
LEDR: Imax = 4mA
0LQ
0D[
+0.59
9  9 
0LQ
+2.32
0D[
5HPDUNV
 6(5,$/,17(5)$&()25/&'
DIMIW, DOMIW, CKMIW, CSMIW1* have the following characteristics:
5HPDUNV
9  9 
9  9 
6LJQDO
0D[
0LQ
0D[
0LQ
PU 100K
+3.2
+2.03
+0.8
-0.5
DIMIW
DOMIW
+0.59
+2.32
CKMIW
+0.59
+2.32
CSMIW1*
+0.59
+2.32
 .(<%2$5',17(5)$&(
R1, R2, R3, R4, R5, R6, C1, C2, C3, C4, C5 and C6 have the following characteristics:
9  9 
9  9 
6LJQDO
5HPDUNV
0LQ
0D[
0LQ
0D[
Input (R1/2/3/4/5/6)
-0.5
+0.8
+2.03
+3.2
ESD protection
PU
Output
+0.59
+2.32
ESD protection
(C1/2/3/4/5/6)
OUI*:
Document 
. All rights of reproduction and disclosure reserved.
Page 34
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
6LJQDO
Ton (ms)
VIL
VIH
0LQ
0.7*VBAT
0D[
0.3*VBAT
7\S
32,31
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
5HPDUNV
PU
 9,%5$7,1*'(9,&(&21752/
CMDVIB have the following characteristics:
6LJQDO
9  9 
9  9 
0LQ
0D[
0LQ
+2.32
+0.59
CMDVIB
ICMDVIB max = 2mA
0D[
5HPDUNV
PD
 9
RXD1, TXD1, CTS, RTS, DCD, DSR, DTR and RI have the following characteristics:
5HPDUNV
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
PU 100K
+3.2
+2.03
+0.8
-0.5
RTS
+2.32
+0.59
RI
+2.32
+0.59
CTS
PD
+2.32
+0.59
DSR
PU 10K
+2.32
+0.59
DCD
PU 100K
+3.2
+2.03
+0.8
-0.5
DTR
TXD1
+0.59
+2.32
PU 10K
+3.2
+2.03
+0.8
-0.5
RXD1
 ,5'$$1'8$57
RXIR, TXIR and CMDIRDA have the following characteristics:
9  9 
6LJQDO
9  9 
0LQ
0D[
0LQ
0D[
RXIR, RXD2
-0.5
+0.8
+2.03
+3.2
TXIR, TXD2,
+0.59
+2.32
CMDIRDA
5HPDUNV
PU 100K
 5(6(7
TESTRST has the following characteristics:
6LJQDO
0LQ
VL (V)
VH (V)
Treset (ms)
0.8 VBAT
65
0D[
0.2 VBAT
5HPDUNV
PD 100K
NB: The reset signal resets all the system including backup.
 63$5(,2
IO5, 6,7,11 have the following characteristics:
6LJQDO
9  9 
9  9 
Document 
5HPDUNV
. All rights of reproduction and disclosure reserved.
Page 35
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
Input
Output
0D[
+0.8
+0.59
0LQ
-0.5
0D[
+3.2
0LQ
+2.03
+2.32
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
IO5,6,7:
programmable PD
IO11:
programmable PU
Iout max = 2mA
 &/2&.6
CLK26M and CLK32K have the following characteristics:
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
+2.32
+0.59
CLK13M
1,32
0,297
CLK32K
6LJQDO
9   9 
5HPDUNV
9   9 
2V
0.5V
CLK26M
5HPDUNV
 3$5$//(/,17(5)$&()25&203$1,21&+,3
DPROC<0..15>, APROC<1..3>, RWPROC*, OEPROC*, CS1PROC* have the following characteristics:
5HPDUNV
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
+3.2
+2.03
+0.8
-0.5
Input
DPROC<0..15>
+2.32
+0.59
Output
DPROC<0..15>,
APROC<1..3>,
RWPROC*,
CS1PROC*,
OEPROC*
NB: The maximum capacitance acceptable on each signal of the parallel interface for companion chip is 25pF
(including copper line capacitance, connectors capacitance… ).
 3$5$//(/,17(5)$&()25/&'
DLCD<0..7>, ESTRBLCD, RWLCD*, CS0LCD*, CS1LCD*, RESETLCD*, RSLCD have the following
characteristics:
5HPDUNV
9  9 
9  9 
6LJQDO
0D[
0LQ
0D[
0LQ
+3.2
+2.03
+0.8
-0.5
Input
DLCD<0..7>
Output
+0.59
+2.32
DLCD<0..15>,
RESETLCD*,
RWLCD*,
CS0LCD*,
CS1LCD*, RSLCD,
ESTRBLCD
NB: The maximum capacitance acceptable on each signal of the parallel interface for LCD is tbd (including
copper line capacitance, connectors capacitance… ).
Document 
. All rights of reproduction and disclosure reserved.
Page 36
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 86%,17(5)$&(
USB_DM, USB_DP, VCUSB have the following characteristics:
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
+3.6
+2.45
+0.93
-0.5
Input
USB_DM, USB_DP
+2.8
+0.682
Output
USB_DM, USB_DP
6LJQDO
VCUSB (V)
0LQ
4.0
5HPDUNV
PU
PU
0D[
5.5
 00&,17(5)$&(
DMMC<0..3>, CLKMMC, CMDMMC, POWMMC, CDMMC have the following characteristics:
5HPDUNV
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
PU 100K
+3.2
+2.03
+0.8
-0.5
Input
DMMC<0..3>,
CMDMMC
PU 100K
+2.32
+0.59
Output
DMMC<0..3>,
POWMMC,
CMDMMC
+2.32
+0.59
CLKMMC
 9,'(26(1625,17(5)$&(
DCAM<0..7>, RESETCAM, STBYCAM, PCLKCAM, VSCAM, HREFCAM, XCLKCAM have the following
characteristics:
5HPDUNV
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
+3.2
+2.03
+0.8
-0.5
Input
DCAM<0..7>,
PCLKCAM
+2.32
+0.59
Output
DCAM<0..15>,
XCLKCAM,
HREFCAM
+2.32
Programmable PU
+0.59
VSCAM,
STBYCAM,
RESETCAM
NB: The maximum capacitance acceptable on each signal of the parallel interface for video sensor is tbd
(including copper line capacitance, connectors capacitance… ).
 0&6,,17(5)$&(
MCSIDI, MCSIDO, MCSICLK, MCSISYNCH have the following characteristics:
9  9 
9  9 
6LJQDO
5HPDUNV
0LQ
0D[
0LQ
0D[
Input
-0.5
+0.8
+2.03
+3.2
MCSIDI, MCSICLK,
MCSISYNCH
Document 
. All rights of reproduction and disclosure reserved.
Page 37
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
+2.32
+0.59
Output
MCSIDO,
MCSICLK,
MCSISYNCH
NB: a pull down as to be added to MCSIDI and MCSICLK
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 ,6,17(5)$&(
CSYNC, CSCLK, CDI, CDO, CRESET have the following characteristics:
5HPDUNV
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
PD 100K
+3.2
+2.03
+0.8
-0.5
CDI
+3.2
+2.03
+0.8
-0.5
Input
CSYNC, CSCLK
+2.32
+0.59
Output
CDO, CRESET,
CSYNC, CSCLK
 ,&,17(5)$&(
SDAI2C, SCLI2C, INTI2C have the following characteristics:
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
+3.2
+2.03
+0.8
-0.5
Input
SDAI2C, INTI2C
+2.32
+0.59
Output
SDAI2C, SCLI2C
5HPDUNV
Programmable PU
on INTI2C
PU 1.8K
 -7$*,17(5)$&(
TCLK, TMS, TDI, TDODIGIT, TDIANALOG, BSCAN*, EMU0*, EMU1* have the following characteristics:
5HPDUNV
6LJQDO
9  9 
9  9 
0D[
0LQ
0D[
0LQ
+3.2
PU
+2.03
+0.8
-0.5
TMS, TDI,
TDIANALOG,
BSCAN*
PD
+3.2
+2.03
+0.8
TCK
-0.5
+2.32
+0.59
TDODIGIT,
TDOANALOG,
EMU0*, EMU1*
+0.59
+2.32
PU
 $'&
3DUDPHWHU
Resolution
Input range
Input capacitor
0LQ
7\S
10 bits
12pF
0D[
1.75V
 ,17(558376
ITDATA and INT1 have the following characteristics :
9  9 
9  9 
6LJQDO
0LQ
0D[
0LQ
Document 
0D[
5HPDUNV
. All rights of reproduction and disclosure reserved.
Page 38
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
+2.03
+0.8
-0.5
ITDATA
+2.03
+0.8
-0.5
INT1
Pulse duration in functional mode: 77ns min.
 9%$&.83
6LJQDO
VBACKUP
PU
PU
+3.2
+3.2
0LQ
0D[
+2.2V
+3.2V
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
5HPDUNV
If no external backup is supplied, VBACKUP has to be connected to VBAT.
With external BACKUP:
- if VBAT < VBACKUP, internal RTC is supplied by VBACKUP.
- if VBAT > VBACKUP, internal RTC is supplied by VBAT.
Without external VBACKUP (VBACKUP input connected to VBAT)
- if VBAT > 2.2V, internal RTC is supplied by VBAT.
- if VBAT < 2.2V, internal RTC is not supplied.
 (19,5210(17$/63(&,),&$7,21
 23(5$7,1*&21',7,216
3DUDPHWHU
Ambient temperature
Supply voltage VBAT
0LQ
-10°C
+3.45V
0D[
+55°C
+4.5V
 &/,0$7,&&21',7,216
3DUDPHWHU
Ambient temperature
Normal range
Ambient temperature
Extended range
Storage temperature
Long damp heat
Operating conditions
Short damp heat
Storage and
transportation conditions
0LQ
-10°C
0D[
+55°C
-20°C
+70°C
+85°C
-40°C
Tested at +60°C, 95% RH during 504 hours
Tested at +40°C, 95% RH during 96 hours
Document 
. All rights of reproduction and disclosure reserved.
Page 39
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 0(&+$1,&$/63(&,),&$7,21
)LJXUH
&2[[;6FRPSRQHQWVLGH
Document 
. All rights of reproduction and disclosure reserved.
Page 40
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
)LJXUH
&2[[;6EDOORXWVLGH
Document 
. All rights of reproduction and disclosure reserved.
Page 41
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
)LJXUH
&2[[;6GLPHQVLRQV
Document 
. All rights of reproduction and disclosure reserved.
Page 42
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
 $11(;(
6LJQDOQDPH
DAIRST
DAIOUT
DAIIN
DAICLK
DIMIW
DOMIW
CKMIW
CSMIW1*
CSMIW2*
ENLED
LEDR
LEDG
R1
R2
R3
R4
R5
R6
C6
C5
C4
C3
C2
C1
OUI*
SIMVCC
SIMRST
SIMCLK
SIMIO
SIMCD
HSMICIP
HSMICIN
HSOL
HSGND
HSOR
MICIP
MICIN
HPP32
HPN32
HPP8
HPN8
CMDVIB
RI
DSR
DCD
,2W\SH
Digital bi directional buffer (IDI041/OUK431)
Digital bi directional buffer (IDI041/OUK431)
Digital bi directional buffer (IDI041/OUK431). Pull down
Digital bi directional buffer (IDI041/OUI431). Pull down
Digital input buffer (IDI041/PS0201). Pull up
Digital output buffer (OUK431)
Digital output buffer (OUI431)
Digital output buffer (OUK431)
Digital output buffer (OUK431)
Digital bi directional buffer (IDG091/OUI431/PE1001)
Digital output buffer (OUI831)
Digital output buffer (OUK431)
Digital bi directional buffer (IDI041/OUI431/PS1001). Pull up
Digital bi directional buffer (IDI041/OUI431/PS1001). Pull up
Digital bi directional buffer (IDI041/OUI431/PS1001). Pull up
Digital bi directional buffer (IDI041/OUI431/PS1001). Pull up
Digital bi directional buffer (IDI041/OUI431/PS1001). Pull up
Digital bi directional buffer (IDI041/OUI431/PS1001). Pull up
Digital output buffer (OUO431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital input. Pull up
Power supply output
Digital output buffer
Digital output buffer
Digital bi directional buffer. Pull up
Digital input buffer (IDI091). Pull down
Analog audio input
Analog audio input
3LQ1ƒ
M4
M3
M2
L2
T5
S4
S5
S6
R3
R4
P2
Q2
O17
P17
P16
Q17
L14
M15
M14
L13
M13
M12
M16
L15
B10
T7
T8
T9
T10
B12
O15
P14
Analog audio output
Analog audio output
Analog audio output
Analog audio input
Analog audio input
Analog audio output
Analog audio output
Analog audio output
Analog audio output
Digital bi directional buffer (IDG091/OUI431/PE1001). Pull down
Digital bi directional buffer (IDG091/OUO431/PS1001)
Digital bi directional buffer (IDG091/OUI431/PE1001). Pull down
Digital output buffer (OUI831). Pull up
O14
N12
O13
R15
Q15
N11
O11
O10
N10
M17
N5
E3
E2
Document 
. All rights of reproduction and disclosure reserved.
Page 43
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
DTR
CTS
RTS
TXD1
RXD1
TXD2
RXD2
TXIR
RXIR
CMDIRDA
INT1
SCLI2C
SDAI2C
INTI2C
CHARGEUR
LEDC
TESTRST
ITDATA
DPROC<0>
DPROC<1>
DPROC<2>
DPROC<3>
DPROC<4>
DPROC<5>
DPROC<6>
DPROC<7>
DPROC<8>
DPROC<9>
DPROC<10>
DPROC<11>
DPROC<12>
DPROC<13>
DPROC<14>
DPROC<15>
RWPROC*
OEPROC*
CSPROC1*
APROC<1>
APROC<2>
APROC<3>
DLCD<0>
DLCD<1>
DLCD<2>
DLCD<3>
DLCD<4>
DLCD<5>
DLCD<6>
DLCD<7>
ESTRBLCD
CS0LCD*
Digital bi directional buffer (IDI091/OUI831). Pull up
Digital output buffer (OUI831). Pull up
Digital bi directional buffer (IDI091/OUO431)
Digital output buffer (OUI831)
Digital bi directional buffer (IDI091/OUI831). Pull up
Digital output buffer (OUI831)
Digital input buffer (IDI091). Pull up
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI091/OUK431). Pull up
Digital output buffer (OUK431)
Digital bi directional buffer (IDG091/OUI431/PS1001). Pull up
Digital bi directional buffer (IDI091/UOS205). Pull up
Digital bi directional buffer (IDI091/UOS205). Pull up
Digital bi directional buffer (IDG091/OUI431/PS1001). Pull up
Power supply input
Analog output
Digital input. Pull down
Digital bi directional buffer (IDI091/OUI431/PS1001). Pull up
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital output buffer (OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI831)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Document 
. All rights of reproduction and disclosure reserved.
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
D3
C5
D4
B5
B7
B8
B9
B6
D7
C7
Q3
C11
B11
H6
O3,O4,O5
L6
P4
N6
K5
K4
K3
K2
J2
J3
J4
I4
I3
I2
H2
H3
H4
G4
G3
G2
I5
F5
F6
F4
F3
F2
I13
N18
L16
I12
G17
K15
H15
I15
I14
H13
Page 44
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
CS1LCD*
RSLCD*
RWLCD*
RESETLCD*
USB_DP
USB_DM
VCUSB
TSPACTEXT
CSYNC
CSCLK
CDI
CDO
CRESET
DCAM<0>
DCAM<1>
DCAM<2>
DCAM<3>
DCAM<4>
DCAM<5>
DCAM<6>
DCAM<7>
RESETCAM
STBYCAM
PCLKCAM
VSCAM
HREFCAM
XCLKCAM
WP1NAND*
WENAND
RENAND
CLENAND
ALENAND
RBNAND*
CE1NAND
DMMC<0>
DMMC<1>
DMMC<2>
DMMC<3>
CLKMMC
CMDMMC
POWMMC
CDMMC
CLK26M
CLK13M
CLK32K
ADC2
MCSIDI
MCSIDO
MCSICLK
MCSISYNCH
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital bi directional buffer (UIS245/UOS181)
Digital bi directional buffer (UIS245/UOS181)
Power supply input
Digital output buffer (OUI831)
Digital bi directional buffer (IDG091/OUM431/PE0201)
Digital bi directional buffer (IDG091/OUI831)
Digital output buffer (IDG091). Pull down
Digital input buffer (OUM431)
Digital output buffer (OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital bi directional buffer (IDG091/OUI431/PE1001). Pull down
Digital bi directional buffer (IDG091/OUI431/PS1001)
Digital bi directional buffer (IDG091/OUI431/PS1001)
Digital bi directional buffer (IDG091/OUO431/PS1001). Pull up
Digital bi directional buffer (IDG091/OUI431/PS1001)
Digital bi directional buffer (IDI091/OUI831/PS1001)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital output buffer (OUI431)
Digital bi directional buffer (IDI041/OUI431)
Digital output buffer (OUI431)
Digital bi directional buffer (IDG091/OUM431/PS0201). Pull up
Digital bi directional buffer (IDG091/OUM431/PS0201). Pull up
Digital bi directional buffer (IDG091/OUM431/PS0201). Pull up
Digital bi directional buffer (IDG091/OUM431/PS0201). Pull up
Digital bi directional buffer (IDG091/OUI431)
Digital bi directional buffer (IDG091/OUM431/PS1001). Pull up
Digital output buffer (OUI431). Pull down
Digital bi directional buffer (IDG091/OUI431/PS0201)Pull up
Analog Clock ouptut
Digital bi directional buffer (IDI041/OUI831)
Digital output buffer (OUK431)
Analog input
Digital input buffer (IDG091)
Digital output buffer (OUM431)
Digital bi directional buffer (IDG091/OUM431)
Digital bi directional buffer (IDG091/OUM431)
Document 
. All rights of reproduction and disclosure reserved.
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
G12
I16
J16
N2
N16
N17
T15
C17
Q8
Q9
O16
M8
K12
D10
C4
C8
E11
C6
F10
C9
D5
L3
M5
C10
L5
L4
C15
H12
I9
E4
D9
D6
D8
E8
D12
B15
B16
B17
D11
C12
B13
B14
T19
L12
R7
Q5
C13
D13
E12
E9
Page 45
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.
Réf. :
Rev. :
Réf. sec. :
Date :
DRAFT
IO5
IO6
IO7
IO11
VBAT
VRIO
VBACKUP
ANTENNE
TCK
TMS
TDIDIGIT
TDODIGIT
TDIANALOG
TDOANALOG
BSCAN*
EMU0*
EMU1*
Digital bi directional buffer (IDG091/OUI431/PE1001)
Digital bi directional buffer (IDG091/OUI431/PE1001)
Digital bi directional buffer (IDG091/OUI431/PS1001)
Digital bi directional buffer (IDG091/OUO431/PS1001)
Power supply input
Power supply output
Power supply input
Analog bi directional HF
Digital input buffer (IDI091/ PE0201). Pull down
Digital input buffer (IDI091/ PS0201). Pull up
Digital input buffer (IDI091/ PS0201). Pull up
Digital bi directional buffer (OUI431)
Digital bi directional buffer. Pull up
Digital bi directional buffer
Digital input buffer (IDI041/ PS0201). Pull up
Digital bi directional buffer (IDI091/OUO431/PS1001). Pull up
Digital bi directional buffer (IDI091/OUO431/PS1001). Pull up
SCT TMO MASV3 SPEC 30
2x xxx xxx – x
12/05/04
N4
N3
J5
E17
F19,F20,F21,F22,F2
3,G19,G20,H19,H20
Q4
P5
I23
T11
T14
C14
D17
R9
P7
D16
C18
B18
OUO231 : rated output current = 1mA (with Voh = Vccmin)
OUI431, OUK431, OUO431 :rated output current = 2mA (with Voh = Vccmin)
OUI831, OUK831 : rated output current = 4mA (with Voh = Vccmin)

(1'2)'2&80(17

Document 
. All rights of reproduction and disclosure reserved.
Page 46
This document contains information on a product under development. SAGEM reserves the right to change or discontinue this product without
notice.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 48
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:1ce70298-b948-4864-8f03-145b338897c5
Creation Date--Text             : 16:23 11/3/2004
Producer                        : GNU Ghostscript 7.05
Creator Tool                    : Windows NT 4.0
Modify Date                     : 2004:11:08 08:57:23+01:00
Metadata Date                   : 2004:11:08 08:57:23+01:00
Document ID                     : uuid:e70bf326-e1be-4726-8a16-5aeb1af06d3d
Format                          : application/pdf
Title                           : Untitled Document
Create Date                     : 16:23 11/3/2004
Creator                         : Windows NT 4.0
EXIF Metadata provided by EXIF.tools
FCC ID Filing: M9H95V3L

Navigation menu