Sam Ash Music XP108W Speaker User Manual XP108W
Sam Ash Music Corporation Speaker XP108W
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3809126 |
| Application ID | ue6Jvnw4BhSeZI/m+oCcIQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 139.43kB (1742821 bits) |
| Date Submitted | 2018-04-09 00:00:00 |
| Date Available | 2018-04-09 00:00:00 |
| Creation Date | 2018-03-20 13:14:59 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2018-04-08 15:38:05 |
| Document Title | XP108W user manual.pdf |
| Document Creator | Adobe Acrobat 8.0 |
| Document Author: | Administrator |
EXPEDITION XP1 08W ZOO—WATT PORTABLE PA SYSTEM Owner's Manual SAMSON ' Copyrighi 2018 v1 Samson Technologies Corp, 2789 Duffy Ave Hicksville, New York 11801 www.5amsohtech.com The BlueroothO word mark and logos are registered trademarks owned by Elueiooth SIG, Inc, and any use oi such marks by Samson Technologies is under license. Other trademarks and irade names are those of their respective owners." Important Safety Information AVIS RISDUE DE DHDG ELECTRONIDUE - NE PAS DUVI‘IIR This lightning Ilash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated "dangerous voltage" WIthIn the product's enclosure that may be oi suiiicierit magnitude to constitute a risk oi electrlc shock. The exclamation point Within an equilateral triangle ls intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (0R BACK) AS THERE ARE NO USER~SERV|CEABLE PARTS INSIDE. REFER SERVICING T0 QUALIFIED SERVICE PERSONNEL. If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. — Private household in the 28 member states oi the EU. In Switzerland and Norway may return their used electronic products iree ot charge to designated collection facilities or to a retailer (it you purchase a similar new one). For Countries not mentioned above. please contact your local authorities for a correct meth» 0d of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative eiiects on the envuonment and human health. XPlusw - Portable PA System 3 Important Safety Information Read these instructions. Keep these instructions. Heed all warnings. Follow all Instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manulacturer‘s instructions. Do not install near any heat sources such as radiators, heat registers, stoves. or other apparatus (including amplillers) that produce heat. 9. Do not deleat the safety purpose oi the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided tor your satety. It the provided plug does not fit into your outlet, consult an electrician lor replacement ol the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at the plugs. convenience receptacles, and at the point where they exit lrom the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart. stand, tripod. bracket, or table specified by the manufacturer, or said With the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury lrom tipover. 13. Unplug the apparatus during lightening storms or when unused lor long periods at time. 14. Reler all servicing to qualified personnel. Service is required when the apparatus has been damaged in any way. such as power supply cord or plug is damaged. liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally. or has been dropped. 15. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid such as vases shall be placed on the apparatus. 16. Caution-to prevent electrical shock, match wide blade plug wide slot lully insert. 17. Please keep a good ventilation environment around the entire unit. 18. To prevent injury. this apparatus must be securely attached to the stand in accordance with the installation instructions. 19. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine. lire or the like. 20. CAUTION: Danger or explosion it battery is incorrectly replaced. Replace only with the same or equivalent type. NQQPWNC‘ 9° Important Safety Information Fcc Notice 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devrce may not cause harmful interference. (2) This devrce must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For: Statement This equipment has been tested and found to comply with the limits for a Class E digital de- vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provrde reasonable protection against harmful Interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not Installed and used in accordance with the instructions, may cause harmiul interference to radio corn- munications. However, there is no guarantee that interference will not occur in a particular installation. It this equipment does cause harmful interference to radio or televrsion recep- tion. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Warning statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with RSS~310 of Industry Canada. Operation is subject to the condi~ tion that this devrce does not cause harmful interference. XPIDEw - Portable PA System 5 lntroduc it Thank you lor purchasing the XP108w battery-powered portable sound system. featuring wireless Bluetooth® connectivity. to stream audio irom your smart phone, tablet. or computer. The XP108w is a complete all-in-one solution providing the flexibility at a four- channel mixer (with inputs for a microphone and line level devices). a line output tor linking multiple speakers. and a master EQ. For a completely untethered performance. the XPlOSw includes a wireless handheld Microphone. For added flexibility. the XPlOSw mixer has a USE jack lor connecting the Samson XPD digital Wireless system. creating a dual wireless performance. Lightweight and compact, the XPlO8w ieatures 200 watts of power weighing less than 24lbs. makes it an excellent complement to any mobile speaker application. The internal battery provides up to 20 hours of audio on a iull charge. The XPIOSw can also be AC powered (with the included power cord) tor continuous audio. Whether you are looking for a sound system for use outdoors. in the classroom. tor karaoke. for presentations. or pertorming live music. the XPlOSw provides high quality. portable audio in a small self-powered package. We recommend you keep the iollowing records lor reference. as well as a copy or your sales receipt. Serial number: Date of purchase: If you have any questions or comments regarding the XPlO8w Portable PA System or any other products lrorn Samson. do not hesitate to contact us at supportesamsontechcom. With proper care and maintenance. your XPlDSw Portable PA System will operate trouble— free for many years. Should your XF108w Portable PA System ever require servicing. a Return Authorization (RA) number must be obtained before shipping your unit to Samson. Without this number. the unit will not be accepted. Please visit www.samsontech.com/ra for an RA number prior to shipping your unit. Please retain the original packing materials and. it possible. return the unit in its original carton. Ii your XPIOBW Portable PA System was purchased outside oi the United States. contact your local distributor. Features 0 Lightweight. 200 watt PA system that weighs 24 pounds 0 Bluetooth connectivity to connect wireless music sources - 2-way speaker enclosure with B" woofer and l" high-irequency driver 0 Four channel mixer with microphone. line level. and USB wireless receiver inputs. - Integrated l 3/ " speaker stand mount - Ergonomic top carry handle - Internal rechargeable battery for up to 20 hours of continuous use - System equalization contour switch for music and spoken word applications I Link output tor expanding your sound system Controls and Connections peso-999$ 1D. 11. 12. 13. ==...._-.. 9.“— ° ..-......_...— ....... :—":':=—='-_‘-?£-- -.'-.:-.-.-_-.- - E MASTER VDLUME - Used to control the overall level of the speaker system. MASTER TREBLE - Controls the highrfrequency tone of the entire system. MASTER BASS - Controls the low-trequency tone oi the entire system. CH1 VOLUME - Controls the level ol the Channel 1 Mic/Line input. LINE/MIC Switch - Adjusts the gain of the CH1 input for a microphone or line level device. our Input - XLR/l/ " input lor connecting a microphone or a device with a line level signal. CH2 VOLUME - Controls the level ol the Channel 2 Aux lnput. AUX Ill - Connect a line level devtce using a ll ” audio cable. LINE OUT - Llne level 1/4" output jack to connect the XPIOBW to the Input at a another XPlO8w to create a dual rnono speaker system. The Line Out is betore the MASTER VOLUME and E0 Controls. BN3 VOLUME - Controls the level ot the internal Wireless microphone as well as the optional XPD USB Wireless receiver. XPD WIRELESS lnput‘ - Connect the Samson XPD digital wireless USE receiver to this input. The wireless receiver gets its power lrorn the XPlOBw, so no additional power supply is needed. The USE connector supplies 5V ZOOmA at ol power to charge a small portable USB device like an MP3 player or smartphone. BLUETUDTHO VfllUME - Controls the level of the Bluetoath input. PAIR Button - Press this button to enable pairing mode in order to connect to a Bluetootti audio device. XPlqu - Portable PA System 7 Controls and Connections 14. 15. 16. 17. 16. 19. 20. BLUETODTHO flansport Buttons - Audio controls for the connected Bluetooth device. VDICEOVER nil/OFF Switch - Turns the VOlCEOVER ducking on or oil. BATTERY Level Indicators - While the XPlOSw is powered 0N and unit is not plugged in, these lights displays the status of the battery charge level. CHARGING Indicator - When the XPlOBw is plugged in and the POWER switch is set to the RECHARGE position. the CHARGlNG indicator will Illuminate RED while it is charging. Once charging is complete the indicator will turn oli. POWER Indicator » Lights green when the power switch is in the ON position. Power/Recharge Switch - This three position switch is used to turn the XPlOSw 0N, OFF or place the system into RECHARGE mode to charge the internal battery. AC INPUT - Connect the supplied power cord here. HT5 Wireless Microphone Controls 1. AUIIIO UN/flff Switch - Turns the handheld transmitter audio signal ON or OFF. when set to the “OFF" position. the audio signal is muted. Because the carrier signal remains on during muting, no "pop" or "thud" will be heard. Note that turning this oil does not turn oft the transmitter power, it is simply a way to temporarily mute the transmission ol audio signal. Battery level meter — This set of three multicolor lights indicates relative battery power, indicating whether the installed battery level is low (redl. mid (yellow) or high (green) strength. One or more oi these will light whenever the transmitter is powered on. When all three are lit, the battery is at maximum strength. When only the red “low" indicator lights, RF perlormance is degraded and the battery needs to be replaced. Power ownrr Switch - Use this to turn the transmitter power ON or OFF. To conserve battery power, be sure to leave it off when not in use. LEVEL Control - Adyusts the input sensitivrty ol the transmitter. Use the supplied plastic screwdriver to raise or lower the input level. Battery holder — Insert a standard 9V battery here, being sure to observe the plus and minus polarity markings shown. We recommend the Duracell MN 1604 type battery. WARNING: Do not insert the battery backwards: doing so can cause severe damage to the transmitter and Will void your warranty. Quick Start 1. Set the XPlOSw power switch to the OFF position, and '7 . .A fully turn all of the LEVEL controls counterclockwise to O. 2. ii an outlet is available. connect the included power cord to the AC input of the speaker, and plug it into an electrical outlet. 3. Set the XP108w power swrtch to the ON position. Connect your audio sources. 5. Turn the MASTER VOLUME control up and set the input levels, tollowrng the steps below. Making Connections Channel I (Microphone [Line Input) 6. Connect a microphone using a standard XLR cable or line level eqmpment using a V4" instrument cable. 7. It connectinga microphone, set the LINE / MlC switch to the down (MIC) position. lI connecting a line level device, set the LINE I MIC switch to the up (LlNE) position. 8. While speaking into the microphone or playing music lrom a line level audio source, slowly raise the channel CH1 VOLUME control until you have reached the desired level. NOTE: It not using the Channel 1 input. turn the VOLUME control all the way down tn keep out any unwanted noise. Channel 2 (Line Input) 9. Connect a line level device using 1/8" instrument cable. 10. While playing music hunt a line level audio source. slowly raise the channel CH2 VOLUME control until you have reached the desired level. channel 3 ~ Included Wireless Microphone 11. Physically place the XP108w where it will be used (the general rule 01 thumb is to maintain "Iine-ol-sight" between the receiver and transmitter). 12. Fully extend the antenna on the top of the XP108w. 13. On the HTS handheld transmitter, unscrew the bottom section oi the microphone by turning it counterclockwise and then slide it off. Make sure the Power switch in the battery compartment is set to OH. 14. Place a fresh 9-volt alkaline battery in the transmitter battery holder, taking care to observe the polarity markings. XPIDEw - Portable PA System 9 Quick Start 15. 16. 17. Turn on the power to the handheld transmitter using Power ONIOFF switch. Replace the bottom section 01 the handheld microphone by sliding it on and then screwing it back on. Make sure the handheld transmitter is not muted by setting the Audio switch to the ON position. Speak or sing into the mic at a normal performance level and raise the CH3 WIRELESS VOLUME control until the desired level is reached. If you need to adiust the microphone gain further (signal is distorted or too weekl. adjust the LEVEL control inside the battery compartment using the supplied screwdriver. channel 3 - XPD Wireless Microphone (sold separately) 18. 19. 20. 21. Plug the XPD USE receiver into the XPD Wireless USB jack. Turn the CH3 WIRELESS VOLUME knob on the XPlOSw completely counterclockwise to 0‘ 0n the wireless handheld transmitter. unscrew the bottom 0 section at the microphone by turning it counterclockwise and then slide it off. Place a lresh set of AA (LR6) batteries in the transmitter battery holder. taking care to observe the polarity markings, then replace the cover. U Turn on the power to the transmitter by pressing and holding Power switch; the indicator LED will light amben 22. Speak or sing into the mic at a normal performance level i A and raise the CH3 WIRELESS VOLUME control until the i 0 D desired level is reached. l—\_ ‘ Bluetnnth 23. Turn the BLUETOOTH VOLUME control down 24. 25. 26. 27. 28. 29. counterclockwrse to 0‘ With the XP108w and your Bluetoolh device powered on; press the PAIR button on the rear panel of the XPlDBw to make the speaker discoverable. The Bluetooth indicator will slowly llash blue. In the settings at your Bluetooth device, set it to “discover" ~ 5:13» ‘ available devices. m From the Bluetooth device list. select the “Samson —’. __——_ ,‘—i XP108W” device. ,‘ i‘ U. ‘ ll your device asks tor a passkey. enter digits 0000 (lour zeros) and press OK. Some devices may also ask you to accept the connection. The XPIOSw speaker indicates that pairing is complete when the indicator turns steady olue. You can now stream audio trom your device to the XP108w speakers With the volume control on your Bluetooth device turned up, play some music, and slowly raise the XPlOSw BLUETOOTH VOLUME control until you have reached the desired level. Using the Masler Ell 10 Quick Start The XPIOBW leature a 2-band equalizer allowmg you to adjust the systems overall high and low frequencies. The lrequericy response is ilat when the knobs are in the vertical or 12 o’clock position. Small movements 0' the controls can make a big difference. Turning the controls all the way up can cause distortion. Use your ears when adiusting the E0 to fit your application. We have provided two example settings to help you get started fine tuning your system. 30. Setting the El] lar Music If you are using the XP108w lor music playback. turn up the BASS and TREBLE slightly to produce a "hi-ti" lrequency response that accentuates the low and high ranges. 31. Setting the Ell tor Vocal if you are using your XPlO8w with a microphone tor speech only, you can reduce the BASS and raise the TREELE slightly, which will produce a frequency response that accentuates the vocal range. MAlewimE our XPIUEw I Portable PA System 11 Charging the Battery The xPlosw has an internal. rechargeable battery capable of up to 20 hours oi continuous audio on a lull charge. Even though the system may have some charge when iirst taken out of the box. we recommend fully charging your XF108w before first using the system. To charge the battery: 1. Connect the XPlOBw to an AC power outlet using the Included power cable. 2. Set the power swnch to the “RECHARGE” posmon. While charging the CHARGING indicator will light red. 4. Keep the system plugged in until the CHARGlNG indicator changes to green, indicating the battery is fully charged. The XPlOSw utilizes a sealed lead-acid gel cell battery. When not in use. the battery will slowly self-discharge. If you are planning not to use the XPlO8w for a long period of time. it Is adinsed to iully charge the unit belore storing. It is also important to charge the unit every six months when not used. This will ensure a healthy battery and extend its llie. if the battery is left with a very low charge tor an extended period of time, it is possible to recharge the battery to working condition. but the charge time can take up to 72 hours. If you iind that the operation time of the XPIOBw becomes noticeably decreased, even after lully charging, the battery should be replaced. Contact Samson customer service or your local distributor tor a replacement battery. 12 OFF RECHARGE Using the LINE OUT Jack The XPlOSw LINE OUT lack allows you to connect the XPlOSw With any powered speaker to expand your system or link two XPlOBw systems together to daisy chain the speakers. Using a standard shielded 1/4" instrument cable, Connect the LINE OUT on the XPlOBw to a line level Input 01 second powered speakert The XP108w WIII send a mix oi all inputs, including Bluetooth® audio. Each channel VOLUME Wlll control corresponding output level to the LINE OUT jack. Using a Speaker Stand The XP108w includes a 13/8" (35mm) pole mount receptacle on the bottom of the cabinet. This tits a standard 1—3/ " (35mm) speaker stand. For maximum coverage when using a speaker stand, the speaker should he raised above the heads at the listening audience. Take care when placmg me speaker on a stand, to ensure that it is on a level, steady surface and will not tip over. Use a stand designed to support a speaker With a minimum weight of 3OIb. XPI 08w I Portable PA System 13 Microphone Holder // The Expedition XP108w includes a handheld microphone holder. To attach the microphone holder. line up the two prongs oi the microphone holder With the center two round openings on the side at the XP108w. Slide the microphone holder into the openings until it is flush with the back ol the speaker cabinet. Transporting the XP108w The Expedition XP108w can be easily transported using the telescopic handle and integrated rolling wheels. Press button on the top handle to extend. Grab the handle. tilt the speaker back and roll it away. 14 mu Specifications X71 08w Power Output Speakers Frequency Response Mic/Line Input Aux Input Wireless Input Line Output Bluetootn Built-in Battery Operation Battery Charging Power Supply Construction Grill Mounting Operating Temperature Dimensions (LxDxH) Weight H15 Wireless Microphone transmitter Frequency Range RF Power Operating Range Audio Frequency Response T,H.D Current Consumption Battery Lite (MN 1604 9-volt alkaline) Operating Temperature Controls LED Indicator Dimensions (o x H) Weight XPIDEw - Portable PA System 200 watts (peak)/ 100 watts (continuous) 8" Wooler + 1" HF Driver 60HZ»18kHZ >3dB XLR - 1/4" combo connector 1/ " USE 1/4" TS Eluetooth V410. AZDP 12V / 3.5AH, Rechargeable it. Sealed Up to 20 hours subject to operating conditions Approx. 6 hours lor a single charge AC:120~24OV, 50-60HZ Polypropylene Perforated Steel Grill, powder coated Integral 1 3/8” Pole Mount Receptacle 40°C ~ +40°C 10.9" x 9.9"x16.9" 277mm x 252mm x 429mm 23,8lb/10.8 kg 173.80 MHZ to 213.20 MHZ (VHF Band) 20 mW (USA models) 10 mW European / UK models 200 ft. 40 Hz to 15 kHz :3 dB < 1% @ 1 kHz 34 mA (typical) 6 hours (typical) -10 to +55 degrees C Power 0n/0fl. Audio On/Oll. Level Control Battery high/medium/low 1.46" x 9.17" / 37mm x 233mm 200 grams I 7.1 oz. 15 Having Trouble with your XPIOBW? We can help! Q? CONTACT OUR SUPPORT TEAM: suppon@samsontech.com Our experts can help you resolve any issues. Fallow us: 3 Q Gsamsnn @samsunlech OsamsanJechnulozi as Samson Technologies Corns 278-8 Dully Ave HIcksvllle. New York 11801 Phone: IVSOOVBVSAMSON (17800737276766) Fax: 63177842201 www.5amsontech.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : Administrator Create Date : 2018:03:20 13:14:59+08:00 Modify Date : 2018:04:08 15:38:05+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2018:04:08 15:38:05+08:00 Creator Tool : Adobe Acrobat 8.0 Format : application/pdf Title : XP108W user manual.pdf Creator : Administrator Document ID : uuid:1650dadf-bc64-4b09-9b28-37d6b303a0d5 Instance ID : uuid:03dce9e9-7364-4028-91b4-d80d413b22e2 Producer : Acrobat Distiller 9.0.0 (Windows) Page Count : 16EXIF Metadata provided by EXIF.tools