Samsung Electro Mechanics BTEP45C2GA Bluetooth Module User Manual BTEP45C2GA User manual

Download:
Mirror Download [FCC.gov]
Document ID	751974
Application ID	f/Mj/1/HC/MGFbMiiLsupA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.59kB (119877 bits)
Date Submitted	2007-01-29 00:00:00
Date Available	2007-01-29 00:00:00
Creation Date	2007-01-17 15:56:28
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2007-01-29 14:16:36
Document Title	Microsoft Word - BTEP45C2GA_User_manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	swyu

- USER MANUAL -
3. External Appearance
Contents
1.
Overview
2.
Major Features
3.
External
4.
Module Block & Interfaces
5.
Demension
6.
FCC & Industry Canada Regulatory Compliance
1) Marking should be in clear and distinguishable characters.
- No dim, spread, cut and erased marking.
1. Overview
2) Appearance should be managed as specified below:
This specification covers Bluetooth module(class-2), which complies
with Bluetooth specification version 2.0 and integrates RF, Baseband,
- No press (depth 0.1mm, length 5mm under).
and Flash in a small package. This module has deployed CSR's BC04
External(BC417143B) chipset.
- No different substance, corrosion, distortion, discoloration
2. Major Features
etc.
-, Bluetooth Spec. v2.0 Complaint
-, Class 2 Level Output Power Available (Max. 4dBm)
- Maintenance of the original condition
-, Full Speed Bluetooth operation with Piconet and Scatternet
(Case's edge, binding between cover and chassis).
support
-, Support of Low power modes: Park, Sniff and Hold
-, 8 Mbit of Flash
-, UART, USB, SPI Interface Available
Size must be as drawn in physical dimension diagram.
4. Module Block & Interfaces
5. Dimension
The dimension is 14.6mm x 14.0mm x 2.2mm(Typ.)
6. FCC & Industry Canada Regulatory Compliance
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
FCC & Industry Canada Regulatory Compliance
the interference by one or more of the following measures:
This device complies with Part 15 of the FCC Rules. Operation is subject to
•
Reorient or relocate the receiving antenna.
the following two conditions: (1) this device may not cause harmful
•
Increase the separation between the equipment and receiver.
interference, and (2) this device must accept any interference received,
•
Connect the equipment into an outlet on a circuit different from that to
including interference that may cause undesired operation.
Your mobile device is a low power radio transmitter and receiver. When it is
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
ON, it receives and also sends out radio frequency (RF) signals. In August
1996, the Federal Communications Commission (FCC) adopted RF
exposure guidelines with safety levels for mobile devices. Those guidelines
are consistent with safety standards previously set by both U.S. and
Statement according to FCC part 15.21
Modifications not expressly approved by this company could void the user's
authority to operate the equipment.
international standards bodies: American National Standard Institute
(ANSI), National Council of Radiation Protection and
Measurements(NCRP), and International Commission on Non-Ionizing
Radiation Protection (ICNRP). Those standards were based on
comprehensive and periodic evaluations of the relevant scientific literature.
The design of your phone complies with the FCC guidelines and applicable.
Statement according to FCC part 15.105
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
RF exposure FCC
This device and its antenna must not be co-located or operating in
conjunction with any other antenna or transmitter.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c829a6bd-e11e-487c-886c-2d107d302428
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2007:01:17 15:56:28+09:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:01:29 14:16:36+01:00
Metadata Date                   : 2007:01:29 14:16:36+01:00
Document ID                     : uuid:a0586139-8504-4e47-b1c1-4df4795fed90
Instance ID                     : uuid:ec2c7187-3aef-4d81-813d-4e4a2fcdd277
Format                          : application/pdf
Creator                         : swyu
Title                           : Microsoft Word - BTEP45C2GA_User_manual.doc
Author                          : swyu

EXIF Metadata provided by EXIF.tools