Samsung Electro Mechanics SWL-2210P WLAN PCI Card User Manual CERTIFICATE OF COMPLIANCE

Samsung Electro Mechanics WLAN PCI Card CERTIFICATE OF COMPLIANCE

UserManual.wiki >

Samsung Electro Mechanics >

SWL 2210P User Manual

Revised Manual

Rhein Tech Laboratories Report number: 2002120 360 Herndon Parkway FCC: Part 15.247 Suite 1400 Industry Canada: RSS-210 FCC ID: E2XSWL-2210P Herndon, VA 20170 http://www.rheintech.com M/N: SWL-2210P Page 45 of 61 APPENDIX J: MANUAL Please see the following pages.

1 SAMSUNG MagicLAN SWL-2210M/P User Manual (Rev. 1.4)

3 5.2.3 The ‘Site Survey’ button…………………….……………………...……..68 5.2.4 Statistics………………...……….………………...…….….…....………..69 5.3 General Settings……………….………..…………...….……………..…….….……69 5.3.1 The ‘DHCP’ button…….………………………………………….…..….69 5.3.2 The ‘Options’ button…………………….…………………….……….….70 5.4 Version……………………………………………………….……………..…….70 6. Troubleshooting ………………………………………………......…….……….…….72 Probable Symptoms and their Diagnosis…………………………………....…..

5 Notice 2 WARNING Important Safety Information !"Read these simple guidelines. Breaking the rules may be dangerous or illegal. SAMSUNG will not be responsible for any damages caused by breaking the rules. !"WLAN Card described in this document is approved for use in a wireless local area network. !"Remember to make backup copies of important data. !"When you are transferring data, keep your laptop computer stationary. Roaming between access points (APs) may break the connection. !"Only qualified service personnel must repair the equipment. !"All wireless devices may get interference, which could affect performance. !"Use approved accessories only. Do not connect incompatible products. !"Use only accessories approved by the WLAN Card manufacturer for use with this particular WLAN Card. The use of any other types will invalidate any approval or warranty applying to the WLAN Card, and may be dangerous. !"Use only the region settings appropriate for the area where the WLAN Card is used at the present time. Using the card in any other region or with an incorrect region setting is prohibited and may be illegal. !"Operation of any radio transmitting equipment, including a WLAN Card, may cause interference with the functionality of inadequately protected medical devices. !"Do not use the WLAN Card on aircraft. !"Do not use the WLAN Card at a refueling point. !"Do not use the WLAN Card near inflammable materials or chemicals. !"Do not use the WLAN Card where blasting is in progress. !"Do not use the WLAN Card when the use of wireless device may cause interference or danger. !"Do not use the WLAN Card where the use of cellular terminals is prohibited. !"Microwave ovens degrade the performance of a wireless LAN drastically. Do not use the WLAN card in the environment where a microwave oven is being used. The device must not be colocated with any other antenna or transmitters. Changes or modifications notexpressly approved by the party responsible for compliance could void the user's authority to operate theequipment. While installing and operating this transmitter and antenna combination the radio frequencyexposure limit of 1mW/cm2 may be exceeded at distances close to the antennas installed. Therefore, theuser must maintain a minimum distance of 20 cm from the antenna.

6 11Mbps High Rate 802.11b Wireless LAN MiniPCI Card ■ Specifications Model Name SWL- 2210M System Interface MiniPCI Spec 1.0 Frequency Band 2.412 ~ 2.462 GHz (Subject to local regulations) Operating Voltage 3.3V±5% from PC Receive :210mA(Typical) Current Consumption Transmit : 390mA(Typical) Data Rate 1, 2, 5.5 or 11Mbps Spreading DSSS(Direct Sequence Spread Spectrum) Output Power 33.9mW(15.3dBm) for 22MHz Bandwidth, 7mW/MHz Receive Sensitivity Typically -85dBm at 11Mbps Security 40-bit/128-bit WEP Encryption Antenna Connector SMT Ultra Miniature Coaxial Connector 2 pieces Available Drivers Linux & Microsoft Windows 98/ME/NT/2000/XP/CE Standards IEEE 802.11b Media Access Protocol CSMA/CA Temperature Range Operating : 0~55℃(32~131℉), Storage : -20~70℃(-4~158℉) Humidity 10% to 90% Non-condensing Operating Range Open Space : 150m(500ft) at 11Mbps, 200m(660ft) at 2Mbps (1024 bytes file transfer) Closed Office: 30m(100ft) at 11Mbps, 50m(160ft) at 2Mbps Dimensions 59.75 ㎜×50.95 ㎜×5.00 ㎜ Certifications & Regulatory Approvals WHQL Certified (Designed For Windows 98/ME/NT/2000/XP). FCC, R&TTE(Europe) CopyrightⓒSamsung Electro-Mechanics Co., Ltd. All Rights Reserved.

11Mbps High Rate 802.11b Wireless LAN PCI Card ■ Specifications Model Name SWL-2210P System Interface PCI Spec 2.2 Frequency Band 2.412 ~ 2.462 GHz(Subject to local regulations) Operating Voltage 5V ±5% Receive :210mA (Typical) Current Consumption Transmit : 390mA (Typical) Data Rate 1, 2, 5.5 or 11Mbps Spreading DSSS(Direct Sequence Spread Spectrum) Output Power 33.9mW(15.3 dBm) for 22MHz Bandwidth, 7mW/MHz Receive Sensitivity Typically -85dBm at 11Mbps Security 40-bit/128-bit WEP Encryption Antenna External 5dBi Patch Antenna with SMA reverse connector and 1.5m cable Available Drivers Linux & Microsoft Windows 98/ME/NT/2000/XP/CE Standards IEEE 802.11b Media Access Protocol CSMA/CA Temperature Range Operating : 0~55℃(32~131℉), Storage : -20~70℃(-4~158℉) Humidity 10% to 90% Non-condensing Operating Range Open Space : 150m(500ft) at 11Mbps, 200m(660ft) at 2Mbps (1024 bytes file transfer) Closed Office: 30m(100ft) at 11Mbps, 50m(160ft) at 2Mbps Dimensions 126.88㎜×70.00㎜×18.00㎜ Certifications & Regulatory Approvals WHQL Certified (Designed For Windows 98/ME/NT/2000/XP). Korea, FCC, R&TTE Approval(CE) and 15EU &4 EFTA Countries Notification completed CopyrightⓒSamsung Electro-Mechanics Co., Ltd. All Rights Reserved.

8 **** Table: The Operating Channels Channel# Frequency FCC Canada ETSI Spain France Japan 1 2412MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 2 2417MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 3 2422MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 4 2427MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 5 2432MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 6 2437MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 7 2442MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 8 2447MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 9 2452MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 10 2457MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ 11 2462MHz ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ ○○○○ ○○○ ○

9 1. MagicLAN Installation 1.1 Introduction Thank you for your purchase of SAMSUNG MagicLAN. Installing this cards allow the computer to join a wireless network based on the IEEE 802.11b (High Data Rate) WLAN standard. You will be surprised how easy for you are a part of the network with no bother of twisted cables. 1.2 Technical Background • What is IEEE 802.11? The IEEE 802.11 specification is a wireless LAN standard developed by the IEEE (Institute of Electrical and Electronic Engineering) committee in order to specify an over an air interface between a wireless client and a base station or Access Point (AP), as well as among wireless clients. Like other IEEE 802 families, IEEE 802.11 specification addresses both Physical (PHY) layer and Media Access Control (MAC) layer. • IEEE 802.11 Physical (PHY) Layer At the PHY layer, IEEE 802.11 defines three physical characteristics for WLAN: diffused infrared, direct sequence spread spectrum (DSSS), and frequency hopping spread spectrum (FHSS). While the infrared PHY operates at the baseband, the other two PHYs operate at the 2.4GHz ISM (Industrial, Scientific, and Medical) band, which can be used for operating wireless LAN devices without the need of end-user licenses. In order for wireless devices to be interoperable, they have to be conforming to the same PHY standard. • IEEE 802.11 Media Access Control (MAC) Layer The IEEE 802.11 MAC Layer is mainly concerned with the rules for accessing the wireless medium. There are two network architectures defined: Ad-hoc Network and Infrastructure Network. • Ad-hoc Network Ad-hoc Network is an architecture that supports mutual communication among wireless clients only. Since Ad-hoc Network does not support access to wired networks, it does not need an Access Point to be a part of the network. You can use the network immediately after setting up the operating mode by installing the supplied network driver.

10 • Infrastructure Network Infrastructure Network is architecture that provides communication between wireless clients and wired network resources. An Access Point (AP) and the associated wireless clients define the transition of data. So a wireless client can access all the services that are available for a regular wired LAN by using an AP. • Roaming Roaming is a service that allows wireless clients to use the network in motion by BSS ABSS ABSS ABSS A BSS BBSS BBSS BBSS B Serve Server

11 automatically changing the connection from an old Access Point to a new Access Point when the clients enter in a new cell. During roaming the clients may observe the loose connection or delay in accessing the resources of the network. • Scanning, Beaconing & ESS ID When a wireless client is initialized, it is necessary for it to find and communicate with the correct group of wireless devices, including AP. At this point, it may search for all the frequency channels and this process is called scanning. There may be multiple APs and networks operating at the same time. It may be necessary to ensure that the station joins with the correct network during the scanning process. To achieve this, each AP is assigned to be part of a logical group called the Extended Service Set (ESS). The name of this logical group is the ESS ID. When roaming is operating, there may be several Access Points as part of the same ESS. After the power on, wireless clients will listen on its default frequency channel. It will be listening for beacons sent by another wireless station or AP. Beacon is a short message containing the ESS ID that will be broadcast roughly ten times a second. When the wireless station hears a beacon and the ESS ID in the beacon matches its own, the client knows that it is on the correct channel and can communicate with its group. If no beacons are seen, or if the ESS ID does not match, the wireless client may move to the next frequency channel and repeat this listening procedure. In case of direct sequence spread spectrum (DSSS) physical layer, this scanning process occurs at start up and may also occur when the client roams between APs. 1.3 MagicLAN Overview • The MagicLAN SWL-2210M/P(MiniPCI/PCI Card) are wireless LAN adapter cards that provide wireless connection between computers. • The MagicLAN is designed to operate with IEEE 802.11 (wireless LAN International Standard) wireless compliant radio cards and uses a CSMA/CA (Collision Sense Multiple Access with Collision Avoidance) algorithm as the media access scheme, which makes high speed communication (with minimal collision probability) possible. • The MagicLAN supports DSSS (Direct Sequence Spread Spectrum) physical layer. This is a radio technique, which scrambles the data prior to transmission and uses a correlation technique on receiver to improve the signal to noise ratio and makes it possible to

12 communicate in the office having a wall and a compartment. • The function of the MagicLAN Access Point is to transfer information from a wired LAN to a wireless LAN and vice versa. When operating, the MagicLAN AP is invisible to most users (Normally, unless the user is an administrator, the MagicLAN AP cannot be seen or accessed by users on the network). • The SWL-2210M/P both for Laptop PC and Desktop PC is small and portable as a roaming function is provided for users who need network services while maintaining mobility. • The MagicLAN supports various network software. The network driver is provided to support network software such as Windows 95(OSR2), Windows 98/98SE,ME, Windows NT 4.0, Windows 2000, Windows XP, Windows CE and Linux. • To get further information of Samsung MagicLAN WLAN Card, please visit our website at http://www.magiclan.com to download the respective drivers.

13 2. Before the Installation The following section will assist you in installing your WLAN Adapter successfully. You will install the SWL-2210M/P Card and software(driver & utility), and finally set the network properties to accommodate resource sharing and select the type of wireless network that you wish to install. The MagicLAN can easily be installed and used, without bothering to connect cables for keeping your computer to use network resources, as in case of a wired LAN. 2.1 What is in Your Package? Please check the contents of the box to make sure everything is included and ready for use. Here is the list of what you should have in your package: • SWL-2210M/P(MiniPCI/PCI Card) • External Antenna • Samsung MagicLAN Installation CD 2.2 System Requirement • Operating System: Windows 95(OSR2)/98/98SE,ME, Windows NT 4.0, Windows 2000, Windows XP, Windows CE, Linux • Computer System (both Laptop and Desktop) with a CD-ROM drive • For Desktop PCI Card (SWL-2210P): The computer system should have extra IRQs and a Memory address. • For Laptop MiniPCI Card (SWL-2210M): The computer system should have MiniPCI Type IIIA, extra IRQs and Memory address. 2.3 Preparations For Installation ◇ You have to prepare Installation CD which is provided by manufacturer. ◇ You can just install SWL-2210M/P cards to use Ad-hoc network. ◇ You need to install Access Poing(AP) to use Infrastructure network.(Refer to the AP Manual about the installation method of AP) ◇ You may need the original CD of (Windows 95(OSR2), Windows 98SE(98),Windows ME, Windows NT 4.0, Windows 2000, Windows XP) to set network environment.

$14 3. MagicLAN Installation For Windows 98/ME/NT4.0/2000/XP/LINUX We will explain the installation method for SWL-2210M/P (MiniPCI/PCI Card) . 3.1 Installation Overview Here are some steps you will perform in establishing your wireless network connection: 1. Install the Access Point at first. AP is needed in case of Infrastructure network mode. 2. You should install the Wireless LAN Card (SWL-2210M/P). 3. Install the software using the Installation CD. 4. Install the network protocol(s) required to communicate on your network. Most likely you will need the TCP/IP protocol. 3.2 Installation Procedure of Windows 98 Please follow the following steps one by one to install the MiniPCI/PCI card successfully. < Method 1 - Inserting card first > 1. Insert the MiniPCI/PCI Card into the slot of your computer. 2. Power on your computer and allow Windows 98 to load fully. 3. “Add New Hardware Wizard” appeared and the system looks for “PCI Network Controller”. Press ‘NEXT’ button and check if “Search for the best driver for your device(recommended)” is slected and then press ‘NEXT’ button . Insert the MagicLAN Installation CD into the CD-ROM drive. 4. Mark the “Specify a location” tap and type “E:\Drivers” right below in this tap(Where E is the CD-drive of your PC) and then press ‘NEXT’.$

15 You can find the “SAMSUNG 11Mbps WLAN MiniPCI/PCI Card ” and now it is ready to install our software. 5. Press ‘NEXT’ and system will copy driver files. You may require Windows 98 CD. Now driver files are fully installed to start the Wireless LAN Card’s operation.

16 If screen message ‘Do you want to restart your Computer now’ will pop up, select No. 6. After rebooting your computer, right click on the My Computer using the mouse and click Properties. 7. Check for the SAMSUNG 11Mbps WLAN MiniPCI/PCI Card by clicking on the Device Manager. If you find the Yellow sign on the adapter, it shows the installation is not successful. Select the Adapter and click on Remove. Restart your computer after uninstalling the driver. (See the Adapter Removal in section 3.9) 8. Right click on the Network Neighborhood using the mouse. Select Properties from the pop up menu. The network box appears and you see three main tabs: Configuration, Identification and Access Control. 9. Click on the configuration tab and then click on the add button. Select Network Component Type box appears. Click on the Protocol then click the Add button. 10. Select Network Protocols box appears. From the list of manufactures, click on Microsoft. From the list of network protocols list, select IPX/SPX and TCP/IP, then click OK.( If you want, you can install the NetBEUI protocol.)

17 11. Select the TCP/IP option for setting the IP address value, Gateway value and DNS value of your computer. After setting these parameters appropriately, click OK to return to Network Component Type. 12. you can select the File and Printer Sharing options as well as the access to your computer by other users connected to that network by setting the appropriate options.

18 13. Screen message ‘Do you want to restart your computer now?’ will pop up. Select Yes. It will shut down your computer and will restart. 14. After booting the computer, you have to draw out and re-insert the MagicLAN Installation CD to be automatically installed. You can click ‘Install Configuration Utility’ to install our utility. Choose the appropriate language when a context box appeared to choose utility’s language. 15. You can set up Wireless LAN environment by our utility program provided. Refer to ‘Chapter 4’ in this manual.

19 < Method 2 – Installing software first > 1. If you insert the MagicLAN Installation CD into the CD-ROM drive, software will launch automatically. Then, click on the ‘Install MagicLAN Driver’. 2. You can see the pictures of Wireless LAN Cards by model name.(SWL-2210M/P MiniPCI/PCI Card). Click on the model name to install it’s driver. 3. Click on Operating System in the right screen in which you want to install driver.

20 3. After installing driver, shut down your computer and insert card. And power on the computer. 4. The system recognize the Wireless LAN Card. 5. The other procedures are same to 7~15 of < Method 1 - Inserting card first > Cf.) The third method : You can combine ‘Method 1’ with ‘Method 2’. In other words, after inserting card into the computer, you can install driver and utility by using the installshield instead, not by the inf file. In case of Windows 2000 and Windows XP, system will recognize the card automatically during installation . Notice that if you install a card after removing it in a Device Manager, you have to mark the check box(“Do you want to scan for hardware changes?”). The function is same to the “Refresh” in ther Device Manager.

21 3.3 Installation Procedure of Windows ME Please follow the following steps one by one to install the MiniPCI/PCI Card successfully. < Method 1 - Inserting card first > 1. Insert the MiniPCI/PCI Card into the slot of your computer. 2. Power on your computer and allow Windows ME to load fully. 3. “Add New Hardware Wizard” appeared and the system looks for “PCI Network Controller”. Check if “Search for the best driver for your device(recommended)” is slected. Insert the MagicLAN Installation CD into the CD-ROM drive. 4. Press ‘NEXT’ and you can find the “SAMSUNG 11Mbps WLAN MiniPCI/PCI Card ” . And the system will copy driver files. Now driver files are fully installed to start the Wireless LAN Card’s operation. If screen message ‘Do you want to restart your Computer now?’ will pop up, select No. 5. After booting the computer, right click on the My Computer using the mouse and click property. 6. Check for the SAMSUNG 11Mbps WLAN MiniPCI/PCI Card by clicking on

22 the Device manager. If you find the Yellow sign on the adapter, it shows the installation is not successful. Select the Adapter and click on Remove. Restart your computer after uninstalling the driver. (See the Adapter Removal in section 3.9) 7. Right click on the Network Neighborhood using the mouse. Select Properties from the pop up menu. The network box appears and you see three main tabs: Configuration, Identification and Access Control. 8. Click on the configuration tab and then click on the add button. Select Network Component Type box appears. Click on the Protocol then click the Add button. 9. Select Network Protocols box appears. From the list of manufactures, click on

23 Microsoft. From the list of network protocols list, select IPX/SPX and TCP/IP, then click OK.( If you want, you can install the NetBEUI protocol.) 10. Select the TCP/IP option for setting the IP address value, gateway value and DNS value of your computer. After setting these parameters appropriately, click OK to return to Network Component Type. 11. you can select the File and Printer Sharing options as well as the access to your computer by other users connected to that network by setting the appropriate options.

24 12. Screen message ‘Do you want to restart your Computer now?’ will pop up. Select Yes. It will shut down your computer and will restart. 13. After booting the computer, you have to draw out and re-insert the MagicLAN Installation CD to be automatically installed. You can click “Install Configuration Utility” to install our utility. Choose the appropriate language when a context box appeared to choose utility’s language. 14. You can set up Wireless LAN environment by our utility program provided. Refer to ‘Chapter 4’ in this manual. < Method 2 – Installing software first > 1. If you insert the MagicLAN Installation CD into the CD-ROM drive, software will

25 launch automatically. Then, click on the ‘Install MagicLAN Driver’. 2. You can see the pictures of Wireless LAN Cards by model name.(SWL-2210M/P MiniPCI/PCI Card). Click on the model name to install it’s driver. 3. Click on Operating System in the right screen in which you want to install driver. 4. After installing driver, shut down your computer and insert card. And power on the computer.

26 5. The system recognize the Wireless LAN Card. 6. The other procedures are same to 5~14 of < Method 1 - Inserting card first > Cf.) The third method : You can combine ‘Method 1’ with ‘Method 2’. In other words, after inserting card into the computer, you can install driver and utility by using the installshield instead, not by the inf file. In case of Windows 2000 and Windows XP, system will recognize the card automatically during installation . Notice that if you install a card after removing it in a Device Manager, you have to mark the check box(“Do you want to scan for hardware changes?”). The function is same to the “Refresh” in ther Device Manager.

27 3.4 Installation Procedure of Windows NT4.0 Please follow the following steps one by one to install the MiniPCI/PCI Card successfully. 1. Insert SAMSUNG 11Mbps WLAN MiniPCI/PCI Card into the slot and power on your computer. 2. Windows NT will start in your computer and follow the below procedures. Notice that there’s some difference between When Windows NT networking is not installed and When Windows NT networking is already installed . <CASE1> When Windows NT networking is not installed: 1. Since there is no Windows NT networking installed yet, you should install your driver manually. To do so, click on Start in task bar, go to Settings and then to Control Panel. 2. Under Control Panel, double click on Network icon. 3. Since there is no Windows NT networking installed yet, you maybe asked if you want to install NT networking first. Click on Yes and then Network Setup Wizard will be start. Select ‘Wired to the network’ and click on ‘Next’. In ‘network setup wizard’ box, click on ‘Select from list button’.

$28 4. In Select Network Adapter box, click on Have Disk button. 5. In Insert Disk box, you may be asked to specify the necessary software directory. Insert the MagicLAN Installation CD into the CD-ROM drive. Type in D:\nt40 (Where D is the CD-drive of your computer) in the blank and click on OK. 6. In Select OEM Option box, you will see SAMSUNG 11Mbps WLAN MiniPCI/PCI Card and select the correct card type and click on OK. You confirm the SAMSUNG 11Mbps WLAN MiniPCI/PCI Card on the next message box. Click on NEXT.$

29 7. Select the network protocols by clicking on the check box. And click on NEXT. You must select ‘TCP/IP Protocol’ among these network protocols at least. 8. In the next box to choose network services to use, make sure that all the services you want to use are checked and click on Next. 9. In the next box it is confirmed that necessary NT networking components are selected. Click on Next.

$30 10. When you are asked to specify the directory that the necessary NT files are copied from, insert your Windows NT CD and type in D:\i386(Where D is the CD-drive of your computer) in the location blank. 11. Some files from the D:\i386 directory are copied and you may be prompted the same box to ask you to specify where NT files are once more. Since it is looking for some files form the MagicLAN Installation CD, insert your MagicLAN Installation CD in CD drive and type D:\nt40 in the blank location and click on continue. 12. Card Setup box may appear. Set each parameters (Network mode, ESSID, and Tx rate etc.) for the proper LAN card configuration.$

31 13. TCP/IP Setup message will pop up. Select NO for not using DHCP. If you select the DHCP option for TCP/IP, you do not need to set the values. 14. If you select the No, enter the IP Address, Subnet Mask, Gateway, and DNS values respectively and then click on OK. 15. Binding properties will pop up. Click on NEXT.

32 16. Now it is ready for starting network. Click on NEXT. 17. You can assign Workgroup/ Domain name. And click on NEXT. 18. Click on the Finish and it will ask you whether you want to restart your computer or not. Click on NO.

33 19. You have to insert the MagicLAN Installation CD to be automatically installed. 20. You can click ‘Install Configuration Utility’ to install our utility. Choose the appropriate language when a context box appeared to choose utility’s language. 21. You should reboot the computer to use our utility properly in the NT-based OSs(Windows NT4.0, 2000, XP). 22. You can set up Wireless LAN environment by our utility program provided. Refer to ‘Chapter 4’ in this manual. <CASE2> When Windows NT networking is already installed: 1. Since there is no Windows NT networking installed yet, you should install your driver manually. To do so, click on start in task bar, go to Settings and then to Control Panel. 2. Under Control Panel, double click on Network icon. 3. Select the Adapter. And click on Add.

$34 4. In Select Network Adapter box click on Have Disk button. 5. In Insert Disk box, you may be asked to specify the necessary software directory. Insert the MagicLAN Installation CD into the CD-ROM drive. Type in D:\nt40 (Where D is the CD-drive of your computer) in the blank and click on OK. 6. In Select OEM Option box, you will see SAMSUNG 11Mbps WLAN MiniPCI/PCI Card and select the correct card type and click on OK. You confirm the SAMSUNG 11Mbps WLAN MiniPCI/PCI Card on the next message box. Click on Next . 7. Card Setup box may appear. Set each parameters (Network mode, ESSID, and Tx rate etc) for the proper LAN card configuration.$