Samsung Electronics Co DRMODEMZ1 DR-Ready Modem User Manual

Samsung Electronics Co Ltd DR-Ready Modem

User Manual

DR-Ready modemUser manualimagine the possibilitiesThank you for purchasing this Samsung product. To receive a more complete service, please register your product atwww.samsung.com/registerWARNINGThe DR-Ready modem only works for the following Samsung models. Since the modem can only be installed in the following models, please confirm that your product is one of the following models.• Refrigerator: RF4289HARS, RSG309AARS• Washer/Dryer: WF461ASP/XAA / DV431ASP/XAA• Dishwasher: DMT-611WHEN INSTALLING YOUR DR-READY MODEMDo not install the modem on an unstable surface.• If the product falls, it may result in injury or damage to property.Do not install the modem near a heater, volatile substance (oil, etc.) or inflammable material.• This may result in electric shock or fire.Do not install the modem in a humid or dusty location, a location exposed to direct sunlight water (rain drops, etc.), or a location where gas may leak.• This may result in electric shock or fire.To reinstall the modem, contact the service center.WHEN USING YOUR DR-READY MODEMDo not connect the DR-Ready modem to an incompatible product.• This may result in a problem or product malfunction.If the modem generates a strange sound, smell or smoke, remove the modem from the product immediately, disconnect the LAN cable and contact the service center.• Failing to do so may result in electric shock or fire.If the modem becomes flooded, immediately remove the modem from the product, disconnect the LAN cable and contact the service center.• This may result in electric shock or fire.If water or a foreign object enters the modem, immediately remove the modem from the product (refrigerator, washer or dishwasher), disconnect the LAN cable and contact the service center.• Failing to do so may result in electric shock or fire.Do not touch the modem or LAN cable with wet hands.• This may result in electric shock, fire or injury.Do not intentionally apply excessive force to the modem.• This may result in a problem with or damage to the product.Do not disassemble, repair or modify the modem yourself.• This may result in electric shock, fire, damage to the product or injury.Do not step on the modem or place an object (laundry, lighted candle, lighted cigarette, dish, chemical, metal object, etc.) on the modem.• This may result in a problem with or damage to the product.Do not use a sharp object with the modem.• This may result in a problem with or damage to the product.CERTIFICATION• FCC: A3L-DRMODEMZ1• ZigBee: ZIG11004ZSE26067-24CHECKING THE PARTSPowerFront panel Rear panelPackaging contentsDR-Ready modem (1)1.5 m direct LAN cable (1) User manual (1)Since there is a magnet at the bottom of the modem, you can easily fix it to the metal part of the product.INSTALLING YOUR DR-READY MODEM IN YOUR REFRIGERATORDR-Port1. Enter the MAC and PIN numbers on the label attached to the bottom of the modem into your DRC. (For the procedures to enter the MAC and PIN numbers, refer to the DRC user manual.)2. Open the rubber cover of the DR-port at the back of your refrigerator and connect the LAN cable supplied with the modem to the DR-port.For the exact position of the DR-port, refer to the user manual for the corresponding refrigerator.3. Close the cover.4. Connect the other end of the direct LAN cable to the Host I/F port of the modem.5. Check the connection. (Refer to the “Confirming the connection” section.)6. Attach the modem to the top or side of the refrigerator.INSTALLING YOUR DR-READY MODEM IN YOUR WASHER OR DRYERDR-Port1. Enter the MAC and PIN numbers on the label attached to the bottom of the modem into your DRC. (For the procedures to enter the MAC and PIN numbers, refer to the DRC user manual.)2. Open the rubber cover of the DR-port at the back of your washer or dryer and connect the LAN cable supplied with the modem to the DR-port.For the exact position of the DR-port, refer to the user manual for the corresponding washer or dryer.3. Close the cover.4. Connect the other end of the direct LAN cable to the Host I/F port of the modem.5. Check the connection. (Refer to the “Confirming the connection” section.)6. Attach the modem to the top or side of the washer or dryer.INSTALLING YOUR DR-READY MODEM IN YOUR DISHWASHERDR-PortKickplate1. Enter the MAC and PIN numbers on the label attached to the bottom of the modem into your DRC. (For the procedures to enter the MAC and PIN numbers, refer to the DRC user manual.)2. Remove the kickplate at the bottom of your dishwasher.3. Open the rubber cover of the DR-port at the bottom of your dishwasher and connect the LAN cable supplied with the modem to the DR-port.For the exact position of the DR-port, refer to the user manual for the corresponding dishwasher.4. Close the cover.5. Connect the other end of the direct LAN cable to the Host I/F port of the modem.6. Check the connection. (Refer to the “Confirming the connection” section.)7. Attach the modem to the bottom of the dishwasher and install the kickplate.Safety informationSetting up your DR-Ready modemQUESTIONS OR COMMENTS?COUNTRY CALL OR VISIT US ONLINE ATU.S 800-SAMSUNG (800-726-7864) www.samsung.comCANADA 800-SAMSUNG (800-726-7864) www.samsung.com/caCode No.: DC68-00000A_ENFEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IMPORTANT NOTE:Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.DR-Ready_Modem_EN.indd 1 2011-05-27 �� 5:15:59
Setting up your DR-Ready modemCONFIRMING THE CONNECTION1. Turn on the power of the product (refrigerator, washer, dryer or dishwasher) where the modem has been installed.2. Connect the direct LAN cable to the modem’s Host I/F port. The Power LED of the modem is lit.3. The Pairing LED of the modem blinks at 0.5 second intervals for up to 10 seconds while attempting to connect to the DRC.If the auto connection process has failed, set the DRC to allow connections and press the modem Pairing button to connect them manually. When it attempts to connect, the Pairing LED starts blinking at a 0.5 second interval and then blinks at a 1 second interval for up to 25 seconds. (For the procedures to set the DRC to allow connections, refer to the DRC user manual.)4. When the connection is established, the Pairing LED is lit.While the DRC is transmitting the DR level, any one of the Level 1, 2, 3 and 4 LEDs can be turned on after the connection.5. If you cannot make a connection, contact the service center.CONNECTING MULTIPLE MODEMSThe ability of the DR-Ready modem to communicate may be impaired depending on the operating environment (distance, obstacles, interference, etc.). If the communication quality is insucient, you can solve the problem by connecting more than one DR-Ready modem or connecting a specialized modem.DRC ModemModemModemModem DRCModem (Depth 1)Modem (Depth 2)Star Topology Tree Topology• Up to 10 modems can be connected to the DRC.• A maximum 3 tree depth is supported.• Up to 10 modems can be connected to the DRC. (Including all the modems used to construct the tree topology.)Connecting DR-Ready modemsThe following is the way to communicate with the DRC via a modem that is installed in another product (refrigerator, washer, dryer or dishwasher).DRC Modem-A Modem-B• Modem-A: An existing DR-Ready modem that is installed in another product.• Modem-B: The DR-Ready modem that is installed in the product you want to use.1. Enter the MAC and PIN numbers of Modem-B into the DRC.2. Connect Modem-B to the product you want to use.3. Press the Pairing button of Modem-A. The Pairing LED blinks at 1 second intervals.4. Press the Pairing button of Modem-B. The Pairing LED blinks at 0.5 second intervals and Modem-B attempts to connect with Modem-A.5. When Modem-B is connected with Modem-A, the Pairing LED of Modem-B is lit.6. When the DRC is transmitting the DR level, the same DR level as that of Modem-A is displayed on Modem-B.Using a specialized modemThe following is the way to communicate with the DRC via a specialized modem.DRC Modem-A Modem-BSpecialized modemYou have to purchase the specialized modem additionally.1. Enter the MAC and PIN numbers of the DR-Ready modem into the DRC.2. Connect the DR-Ready modem to the product you want to use.3. Supply power to the specialized modem using the Samsung adapter (ATADU43KBK).4. Press the Pairing button of the specialized modem. The Pairing LED blinks at 1 second intervals.5. Press the Pairing button of the DR-Ready modem. The Pairing LED blinks at 0.5 second intervals and the DR-Ready modem attempts to connect with the specialized modem.6. If the DR-Ready modem is connected to the specialized modem, the Pairing LED of the DR-Ready modem is lit.USING THE REAR PANELPower1 2 3 41Reset button Press this button to reset the modem to the factory default settings.2Host I/F port This port is used to connect to a product with the direct LAN cable.3Pairing button Press this button to make or remove a connection to the DRC or gateway.4Power terminalThis is the port to connect an adapter when using the modem by itself.Use only an ATADU32KBK adapter.CHECKING THE LED1 2 3 4 5 61Power LED (Green, ON/OFF)2Demand Response Level1 Indication LED (Green, ON/OFF)3Demand Response Level2 Indication LED (Green, ON/OFF)4Demand Response Level3 Indication LED (Green, ON/OFF)5Demand Response Level4 Indication LED (Green, ON/OFF)6Chip LED (Green)• ON: When the modem is connected to the DRC or gateway.• Blinking at a 1 second interval: When the modem is waiting to Pair or is exchanging the security key.• Blinking at 0.5 second intervals: When the modem is attempting to pair.• OFF: When the modem is not connected to the DRC or gateway.TROUBLESHOOTINGProblem SolutionThe modem is not turned on.• Check if the product is connected to the power source.• Check if the DR-Ready modem is properly connected to the product with the direct LAN cable.• In the case of a specialized modem, check if the adapter is connected.The Pairing LED is turned o or all the Level 1, 2, 3 and 4 LEDs are turned on.• Check if the DRC in your house is working properly.• Check that the DRC is turned on.• Check if the modem’s MAC and PIN numbers have been entered into the DRC correctly.• Set the DRC to allow connections and press the modem’s Pairing button to connect them manually. (For the procedures to set the DRC to allow connections, refer to the DRC user manual.)Both Level 1 and 2 LEDs are turned on.• Check if the DRC in your house is working properly.• Check that the DRC is turned on.• Check if the modem’s MAC and PIN numbers have been entered into the DRC correctly.• Set the DRC to allow connections and press the modem’s Pairing button to connect them manually. (For the procedures to set the DRC to allow connections, refer to the DRC user manual.)SPECIFICATIONFeature Detailed descriptionAntenna type Chip antennaOperation Voltage 5V DC ±10% or 3.3V DC±10%Power Supply from Host 150mA @ 5V DC150mA @ 3.3V DCInterface Host I/F, PowerLEDPower • ON : Power is on• OFF : Power is oDemand Response Level IndicatorLevel1 ~ Level4Pairing• ON : as paired• Blinking : hand shaking• OFF : not pairedButton TX/RX pairingResetDimension 80 x 55 x 20 mmZigBee• Compatible with IEEE802.15.4 standard to provide wireless 250Kbps data rate• Operation at 2.4GHz frequency band to meet worldwide regulations• Compliant with SEP1.0Using your DR-Ready modem Troubleshooting AppendixDR-Ready_Modem_EN.indd 2 2011-05-27 �� 5:16:00

Navigation menu