Samsung Electronics Co HD2018GH SMART READY User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3773866
Application ID	vOt+1Wq5ENZTl9i4vobjHQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.82kB (422708 bits)
Date Submitted	2018-03-08 00:00:00
Date Available	2018-03-08 00:00:00
Creation Date	2018-03-08 11:50:05
Producing Software	Microsoft® Word 2016
Document Lastmod	2018-03-08 11:50:05
Document Title	User Manual
Document Creator	Microsoft® Word 2016
Document Author:	UCS

User manual of SMART READY
1. Introduction
Based on the S5JT200X48 (T200) SoC, the ARTIK Dongle WiFi module(SMART READY) enables a variety
of platforms with high integration for development and evaluation products. It can be integrated into OEM
products to quickly connect to Wi-Fi systems to provide Wi-Fi services.
The ARTIK Dongle module (SMART READY) includes the following components:
S5JT200X48(T200) chip
An
integrated PA, LAN, T/R Switch to save cost and size, minimize tuning and tolerance
2.4GHz
16MB

Metal antenna
SPI Flash memory and etc.
USB A-Type Connector
The T200 is a single band 2.4GHz 1x1 802.11 b/g/n device optimized for low-power embedded applications
with single-stream capability for both Tx and Rx. It has an integrated network processor with a large set of
TCP/IP with IPv4/IPv6-based services. These services can be accessed via a serial SPI link or by a UART link
connected to an external host CPU.
The smart Dongle product is OPTION mounting device which installs on SMART READY product
among Samsung Electronics life home appliance and which it operates the Wi-Fi function and SMART
HOME.
Application
instrument
Samsung SMART READY home appliances (The refrigerator, air conditioner, air cleaner, washer,
and oven)
The device hardware and software does not allow operation with laptop and operation in portable
condition is not possible.
Version 1.0
page 1 of 5
2. Hardware Architecture
2.1 Circuit Block Diagram
Figure 1-1 SMART READYblock diagram and System Interface
3. WIFI link feature and Interface
3.1 RB02 Wi-Fi link features
IEEE
802.11 b/g/n, single stream 1x1
Single-band
Integrated
Green
Low
PA, LNA and T/R switch
Tx power saving mode
power listen mode
Six-layer
Data
Full
2.4 GHz
PCB design
rates up to 150 Mbps
security support : WEP64/128,WPA (personal),WPA2 (personal), AES, TKIP, WAPI,
PUF(Physically Unclonable Function)
3.2 T200 manufacturing interface
USB
2.0 interface with integrated controller and PHY for manufacturing test and configuration
Version 1.0
page 2 of 5
3.3 T200 host interfaces
SPI
slave interface to the MCU. Host driver source code and programming APIs are available.
UART
host interface to a remote microcontroller with an AT style command set.
3.4 RB02 interface summary
Host
interface: SPI slave or master x 1, SDIO2.0 x 1, debug UART x 1
High
speed UART x 1
Up to 3Mbps data rate
I2C master x 1, I2C slave x 1
Standard-mode and fast-mode
I2S x 1
PWM x 7
18-bit resolution with 8-bit clock prescaler
ADC x 4
12-bit resolution, 400 Ksps for multiple channels and 1 Msps for single channel.
All signal pins can be multiplexed as GPIO
USB2.0 x 1
Version 1.0
page 3 of 5
4. The caution for the safety
It is the content that keeps the user safety and prevents the damage to on property. Certainly, read well
and use the product correctly.
The injury which doesn't follow the safety caution and which it happens or on damage Samsung
Electronics doesn't take the responsibility.
Don't install on the other USB port of the Samsung Smart Ready home appliances in addition to.
In the product, discontinue the product use for some time if the heating is serious. -. In the product, in case
of contacting the skin and long time by the condition where the heat happens, there is the worry about the lowtemperature burn including the red spot, pigmentation, and etc.
The hot-air balloon ( stove, microwave steamer, and etc.)Put on the, heating cooking tool and high
pressure tool near or don't deposit in the inside. -. It has a fever in the product or can be caused by of the fire.
Drop the product or the external shock don't add. -. Put on the inclined place or don't keep the product. -. It
can be damaged by the impact in case of falling. And it is caused by of the malfunction.
Be careful so that the child or infant or pet sucks the product or it doesn't may bite. -. The damage can be
caused to the product.
Don't originally use the product for the use in addition to other purpose. Put on the dry place without the
dampness or moisture. -. The moisture or liquid component can cause the damage to product part and circuit.
-. After it doesn't connect with the case USB port where it gets wet and the removal does the moisture with the
towel parched up, take to the service center.
Remodel into the user discretion or don't repair the separation. -. Free repair cannot be received in the user
discretion in the revision, separation, and case that it collected. And certainly repair take advantage of the
Samsung Electronics authorized service center.
Be careful when cleaning the product. -. When cleaning the product, wipe lightly with the soft stuff. -. Don't
use the poisonous chemistry substance strong or the detergent etc. in order to clean the product. Product outer
tube is discolored or it can be corroded.
Version 1.0
page 4 of 5

: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void
user’s authority to operate the equipment.
This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the RF
exposure requirements.

This product complies with RSS-247 of Industry Canada. Operation is subject to the following two conditions: (1) this product may not
cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired
operation. This Class B digital apparatus complies with Canadian ICES-003.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Version 1.0
page 5 of 5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 5
Language                        : ko-KR
Tagged PDF                      : Yes
Author                          : UCS
Creator                         : Microsoft® Word 2016
Create Date                     : 2018:03:08 11:50:05+09:00
Modify Date                     : 2018:03:08 11:50:05+09:00
Producer                        : Microsoft® Word 2016

EXIF Metadata provided by EXIF.tools