Samsung Electronics Co SD604F DVD ROM DRIVE User Manual MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	20599
Application ID	MTL7FFqi4j3+nYE3nHfL8A==
Document Description	MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	67.89kB (848571 bits)
Date Submitted	1999-01-22 00:00:00
Date Available	1999-03-11 00:00:00
Creation Date	1998-11-12 08:36:43
Producing Software	Acrobat Distiller 3.0 for Power Macintosh
Document Lastmod	1998-12-10 11:23:48
Document Title	MANUAL

SDR(Eng)
11/12/98 8:11 AM
Page 1
Safety Warnings
Internal DVD-ROM DRIVE
SD-604
User’s Manual
You must not use the drive in any manner other than that specified in this guide.
CAUTION
Do not attempt to repair the DVD-ROM drive yourself. Contact your
dealer or local SAMSUNG representative for all repairs.
Use of controls or adjustments or performance of procedures other than
those specified here in may result in hazardous radiation exposure.
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARRANTY Please refer to the Samsung limited warranty statements.
As SD-604 has a steel ball installed in the turntable for the purpose of reducing the
vibration and noises to be generated while the disc shaft rotates, you may hear the ball
clicking sounds when the driver is handled manually or when it rotates at a low speed.
But it is not a problem.
English
The following diagrams illustrate the precautions to be taken when using
your DVD-ROM drive.
SDR(Eng)
11/12/98 8:11 AM
Page 2
Front View of the DVD-ROM Drive
Rear View of the DVD-ROM Drive
English
COMPACT
5 6
1 Headphone Connector
1 Digital Output Terminal
The audio output connector enables you to plug stereo headphones into the drive.
It requires a 3.6 mm stereo mini-jack.
Connect an audio cable of the board that supports digital output to this terminal.
2 Audio Output Connector
2 Volume Control Dial
This control dial adjusts the volume for your headphones.
You can only use the headphone jack and volume control when you have installed the
required software utilities. For example, the Microsoft Windows Media player can be used.
You can connect a sound card to your drive using this four-pin connector.
➢This function is not covered in detail in this guide. Refer to the documentation supplied
with your sound card.
3 Device Configuration Jumper
3 LED
It lights when a DVD/CD disc is loaded or is worked.
Usually, this is a pre-set configuration as illustrated below:
C S M
S L A
4 Disc Tray
The disc tray opens and closes automatically when you press the Open/Close button.
☛ When you place a disc in the tray, make sure that the label on the disc is facing
upwards. If you are not loading or unloading a disc, the tray should remain closed.
5 Emergency hole
If the tray does not open when you press the Open/Close button, insert a small, metal
rod (for example, an unwound paper clip) into this hole to eject the disc.
☛ This function should only be performed when the computer is powered OFF.
6 Stop(Open/Close) Button
When in play, press the stop key and when in stop, press open/close key.
☛Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it
in the correct position.
4 Host IDE Interface Connector
This input/output interface connector is used to connect the 40-pin flat cable from the
IDE interface to the drive.
5 Power Connector
The power connector is a four-conductor male plug.
SDR(Eng)
11/12/98 8:11 AM
Page 3
System Requirements
Installing the Software
Before you install the DVD-ROM drive, we strongly recommend that you make certain that
your set-up meets the system requirements listed below.
You can install the device driver for DOS or for Windows.
Description
Intel Pentium 166MHz, RAM 16MB(or higher) with an
IDE interface (or a 100% IBM-compatible computer)
Free expansion unit
5.25 inch
Disk space
100 MB minimum
Windows version
95 OSR2 (or higher)
Playback of DVD Video
Turn on your computer and wait for it to boot.
Insert the driver disk into a floppy disk drive (usually the A drive).
If you are a...
Then...
DOS user
◆ Type a: at the DOS prompt.
◆ Press the RETURN key.
PC with Window95 OSR2
DVD-Video playback software and appropriate hardware
(MPEG2 card etc.)
Windows user
◆ Access the File Manager.
◆ Click on the A icon.
Windows 95 user
◆ When you are in Windows 95, it is not necessary to
install Device Driver. Whereas, when you are in Dos
Mode of Windows 95, then install as follows.
◆ Click on MY COMPUTER icon.
◆ Click on the A icon.
❉For further details, refer to the documentation that comes with DVD-Video playback software
Installing the DVD-ROM Drive
Install the drive in your computer horizontally, making sure that the Open/Close
button is on the right.
To install the drive, proceed as follows.
Windows 95 user
Windows 95 user
If you are a...
1 Turn OFF your computer. Remember to verify the
configuration jumper on the rear of the DVD-ROM drive.
2 Remove the cover of your PC(main unit of the computer).
3 Remove the blank cover panel for the 5.25 inch unit in
which the DVD-ROM drive is to be installed.
6 Put the cover back on your PC.
◆ Type CDSETUP after the a: prompt.
◆ Press RETURN.
Windows user
Double-click CDSETUP.EXE from the Windows
File Manager.
To...
When the Setup Completed screen is displayed, remove the installation floppy disk from the drive.
5 Install the DVD-ROM drive into the unit and secure it with
mounting screws (recommended standard M3x6x4).
◆ Depending on your PC model, you may need to attach
guide rails to the drive, so that the drive is held firmly in place.
On the ground that the guide rails are parts of the computer,
if you don’t have these, please purchase separately.
◆ If you use screws that are longer than the recommended
standard, you may damage the drive.
Then...
DOS user
Windows 95 user
Double click on CDSETUP icon.
Result: The CD/DVD-ROM Setup Program dialog box is displayed.
4 Connect the DVD-ROM drive to the IDE interface and
power cables located inside your computer.
☛Connectors are keyed so it is impossible to put them in an incorrect
position. Do not force the connectors, if they do not seem to fit.
Run the program:
Then enter...
Confirm the installation
Exit without installing
Result: If you answer Y (Yes), the installation program automatically
◆ Creates a SAMSUNG directory on your hard disk,
◆ Copies the required softwares,
◆ Modifies the CONFIG.SYS and AUTOEXEC.BAT files.
Reboot your system.
Result: ◆ The computer restarts
◆ Both the device driver and MSCDEX are loaded.
English
Item
Type of computer
SDR(Eng)
11/12/98 8:11 AM
Page 4
Changing the Drive and Driver Settings
MSCDEX.EXE Parameters
The MSCDEX.EXE parameters are added to your AUTOEXEC.BAT file. Below is the syntax for each
parameter. Information indicated within square brackets [ ] is optional.
\\MSCDEX.EXE [/E/K/S/V] /D: [/L:] [/M:]
Example : The default set-up procedure adds the following default settings to your AUTOEXEC.BAT file:
Parameter
Details
/P:
Specifies the port for the interface card.
Possible values: 1F0, 170
Default: 1F0.
/D:
Changes the name for the DVD-ROM drive. Up to eight
characters can be input.
Default: SSCD000.
✽ Refer to README. DOC.
Resolving Technical Problems
Please consult the following table BEFORE contacting your dealer or local SAMSUNG
representative.
C:\SAMSUNG\MSCDEX.EXE /D:SSCD000
Details for each parameter are listed below.
Parameter
Details
/D:
Specifies the name of the top DVD-ROM drive. The  field
must contain the same information as specified by parameter in your
CONFIG.SYS file (which loads the corresponding DVD-ROM drive).
☛The MSCDEX command must have at least one /D parameter.
If you add another DVD-ROM device, you must add and specify
a corresponding /D parameter for each new drive.
/E
/K
/S
/V:
If the EMS memory mode (Expanded Memory Support) is
enabled, this parameter specifies that the DVD-ROM driver
can save sector buffers using EMS memory.
Specifies that MS-DOS can recognize a DVD-ROM volume
written in kanji (Chinese characters). Must be used for all
DVD-ROM volumes written in kanji.
Permits the DVD-ROM drive to be shared on the MS-NET or
Windows for Work Groups server.
When MSCDEX.EXE is loaded, this parameter indicates the
memory status.
/L:
Specifies the letter of the top DVD-ROM drive. If more than
one DVD-ROM drive is connected, the system automatically
assigns arbitrary drive names to the additional drives.
/M:
Specifies the number of sector buffers.
SSCDROM.SYS Parameters
The SSCDROM.SYS parameters are added to your CONFIG.SYS file. Below is the syntax for each
parameter. Information indicated within square brackets [ ] is optional.
DEVICE=\\SSCDROM.SYS /D: [P:]
Example : The default set-up procedure adds the following default settings to your CONFIG.SYS file:
Device=C:\SAMSUNG\SSCDROM.SYS /D:SSCD000 /P:1F0,14,1
Problem
Meaning/Solution
The software
installation failed
◆ Check that your hard disk is not full.
◆ The installation floppy disk may be corrupted.
Repeat the installation with the backup floppy disk.
I re-booted my PC
and it paused
during the start-up
program.
After installing the device driver, your system start-up program
may take more time than expected. If it does not start-up after
60 seconds, verify your AUTOEXEC.BAT file and, if necessary,
contact your local computer dealer.
The disc tray does
not open.
The drive may not be installed correctly.
Verify the physical installation.
In the File
Manager, the
DVD-ROM icon
does not display.
If you have installed the DVD-ROM drive...
Then...
And the software
Re-boot your PC.
And have not installed the software
Install the software
following the instructions
on page 5.
I installed the
software and rebooted my PC. The
DVD-ROM drive
icon/directory still
does not appear.
◆ Verify the connections between the drive and your PC.
Check that the 40-pin flat cable is connected to an IDE
interface (some PCs are equipped with an SCSI disk
interface).
◆ Verify your AUTOEXEC.BAT file. Go to page 6 for the
verification procedure.
◆ Check the LASTDRIVE= command in the CONFIG.SYS file.
The specified letter must take the DVD-ROM volume into
account. If you do not know which letter is assigned to the
DVD-ROM, enter Z.
◆ Using the documentation provided with your PC, check that
the IDE hard disk is set up in MASTER mode.
English
Your DVD-ROM drive is controlled by:
◆ MSCDEX.EXE (a Microsoft CD-ROM extensions program)
◆ SSCDROM.SYS (the CD/DVD-ROM device driver)
Details for each parameter are listed below.
SDR(Eng)
11/12/98 8:11 AM
Page 5
Technical Specifications
Question & Answer
SAMSUNG continually strives to improve its products. Both the design specifications and
these user instructions are thus subject to change without notice.
SD-604
SECTIONS
DVD
CD
DVD-ROM, DVD-VIDEO, CD-DA(Audio), CD-ROM,
Disc types supported
Video CD ready, Enhanced CD, CD-I/FMV, CD-R,CD-RW
DISC
Disc diameter
12cm or 8cm
Rotational speed
2770 r.p.m
(linear velocity 3.49m/sec)
6700 r.p.m
(linear velocity 1.3m/sec)
Sustained : Max. 6480KB/sec
Sustained : Max. 4800KB/sec
(32X)
Access time(1/3stroke) 100ms(Typical)
DRIVE
PERFORMANCE Data buffer capacity 512KB
Laser
Semiconductor Laser
Slide mechanism
Stepping motor
Spindle motor
Brushless motor
95ms(Typical)
FRONT PANEL
REAR PANEL
GENERAL
RELIABILITY
MODE1:10-12, MODE2:10-9
10-15
Eject button
Auto eject or Auto inject
Indicator(LED)
BUSY
Headphone output
Stereo mini-jack(Ø3.6mm) 0.60±0.06V(rms) 33Ω
Volume control
Dial type
Required power
+5VDC : 1.0A, +12VDC : 1.5A (Max)
Interface connector
ATAPI
What is Regional Code?
What is the difference of DVD-ROM DRIVE and DVD PLAYER?
A DVD player has a MPEG2 decoder, but a DVD-ROM drive hasn’t a MPEG2
decoder, so you need appropriate hardware to decode MPEG2 data on a disc.
(MPEG2 card etc.)
Where can I get DVD disc or MPEG2 card?
You can get DVD discs at big disc stores, get MPEG2 card at computer stores.
Audio output
Line out 0.70 ± 0.07V(rms) : 47KΩ
Jumper block
Device configuration jumper
Work area
OPERATING
ENVIRONMENT Storage area
A MPEG2 card and discs have regional code numbers. It is only possible to play a
disc on a DVD-ROM drive when MPEG2 card has the same regional code with the
disc.
Loading mechanism Tray. DC motor(Soft Eject). Horizontal/Vertical
ERROR RATE
What is MPEG2 card?
A MPEG2 card decode data of MPEG2 format on a DVD disc.
There is a soft-MPEG2 lately.
Data transfer rate
PIO Mode 4 : 16.6MB/sec
Multiword DMA mode 2 : 16.6MB/sec
What is DVD?
A disc that the data capacity of a single-layer and single-sided DVD, at 4.7GB(Giga
Byte), is 7 times that of a CD. The picture data uses the MPEG2 format, one of the
worldwide standards of digital compress technology.
CD-ROM XA, CD-Plus, CD-Extra, Photo-CD(Single,Multi-session),
Temperature : 5 ~ 45°C,
Humidity : 8 ~ 80%
Temperature : -20 ~ 55°C,
Humidity : 5 ~ 85%
Dimensions
149(W) x 41.5(H) x 200(D)mm (Including bezel)
Net weight
900g
MTBF
125,000 POH(Duty 20%)
Disc tray loading
50,000 times

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 1998:11:12 08:36:43
Producer                        : Acrobat Distiller 3.0 for Power Macintosh
Modify Date                     : 1998:12:10 11:23:48
Page Count                      : 5

EXIF Metadata provided by EXIF.tools