Samsung Electronics Co SGHZ300 Single-Band PCS GSM Phone User Manual Z110VEng4Vodafone

Samsung Electronics Co Ltd Single-Band PCS GSM Phone Z110VEng4Vodafone

UserManual.wiki >

Samsung Electronics Co >

SGHZ300 User Manual

Users Manual

* Depending on the software installed or your service provider, some of the descriptions in this manual may not match from your phone.* Depending on your country, your phone and accessories may appear different from the illustrations in this manual.World Wide Webhttp://www.samsungmobile.comPrinted in KoreaCode No.:GH68-XXXXXAEnglish. 03/2005. Rev 1.0

Draft2005. 03. 25(SW version: Z300BOEC5)SGH-Z300User’s Guide

ImportantsafetyprecautionsFailure to comply with the following precautions may be dangerous or illegal.Use road safety at all timesDo not use a hand-held phone while driving. Park the vehicle first. Switch off the phone when refuellingDo not use the phone at a refuelling point (service station) or near fuels or chemicals.Switch off in an aircraftWireless phones can cause interference. Using them in an aircraft is both illegal and dangerous.Switch off the phone near all medical equipmentHospitals or health care facilities may be using equipment that could be sensitive to external radio frequency energy. Follow any regulations or rules in force.InterferenceAll wireless phones may be subject to interference, which could affect their performance.

1Important safety precautionsBe aware of special regulationsMeet any special regulations in force in any area and always switch off your phone whenever it is forbidden to use it, or when it may cause interference or danger.Water resistanceYour phone is not water-resistant. Keep it dry. Sensible useUse only in the normal position (held to the ear). Avoid unnecessary contact with the antenna when the phone is switched on.Emergency callsKey in the emergency number for your present location, then press . Keep your phone away from small children Keep the phone and all its parts, including accessories, out of the reach of small children.Accessories and batteriesUse only Samsung-approved accessories and batteries. Use of any unauthorised accessories could damage your phone and may be dangerous.Qualified serviceOnly qualified service personnel may repair your phone.For more detailed safety information, see "Health and safety information" on page 76.• The phone could explode if the battery is replaced with an incorrect type.• Dispose of used batteries according to the manufacturer’s instructions.

2About this GuideThis User’s Guide provides you with condensed information about how to use your phone. To quickly learn the basics for your phone, please refer to “Get started” and “Step outside the phone.”In this guide, the following instruction icons appear:Indicates that you need to pay careful attention to the subsequent information regarding safety or phone features.Indicates that you can get more information on the referenced page. →Indicates that you need to press the Navigation keys to scroll to the specified option and then select it.[ ] Indicates a key on the phone. For example, [OK]< > Indicates a soft key, whose function is displayed on the phone screen. For example, <Msg.>•3GYour phone is capable of operating in a 3G environment, allowing much greater data transfer speed, video streaming, and video conferencing. Special features of your phone• Camera and camcorderUse the camera module on your phone to take a photo or record a video.•Media playerPlay media files on your phone.•IrDASend and receive Phonebook and Organiser data and media files via an infrared port.

51 Profilesp. 302 My Mediap. 31PhotosPicturesSoundsGames & MoreVideosMusicp. 31p. 32p. 33p. 33p. 34p. 353 Call registerp. 361 Missed calls2 Dialled calls3 Received calls4 Current contacts5 Data calls6 Calls cost7 Calls timep. 36p. 37p. 37p. 37p. 37p. 37p. 384 Messagesp. 381 Create new2 Inbox3 Drafts4 Outbox5 Sentbox6 Email inbox7 Templates8 Broadcast9 Delete all0 Settings Memory statusp. 38p. 40p. 42p. 43p. 43p. 43p. 44p. 45p. 45p. 45p. 485 t-zonesp. 496 Contactsp. 501 Search contact2 New contact3 Groups4 Speed dial5 My name card6 Copy all7 Own number8 Contact settings9 Memory status0 Service number**p. 50p. 51p. 51p. 52p. 52p. 52p. 53p. 53p. 53p. 537 Organiserp. 531 Alarm2 Calendar3 Week view4 Today’s events5 Schedule6 Anniversary7 Task8 Memo9 Voice memo0 World clock Math Memory statusp. 53p. 54p. 56p. 56p. 56p. 57p. 57p. 57p. 57p. 58p. 58p. 598 Camerap. 609 Settingsp. 641 Profiles2 Time & date3 Phone4 Display5 Call6 Connectivity7 Application settings8 Security9 Memory status0 Reset settings Internetp. 64p. 64p. 64p. 65p. 65p. 67p. 71p. 72p. 73p. 73p. 73* Shows only if a memory card is inserted into the phone.** Shows only if supported by your USIM/SIM card.Menu functionsTo access Menu mode, press [OK] in Idle mode.

6UnpackMake sure you have each itemYou can obtain various accessories from your local Samsung dealer.Phone Travel ChargerBattery PC Data CablePC Link CD User’s ManualMemory cardThe items supplied with your phone and the accessories at your Samsung dealer may vary, depending on your country or service provider.Your phoneButtons, features, and locationsMicrophoneHeadset jackNavigation keysDial keyEarpieceDisplayVolume keysInterior camera lens Camera keyMemory card slotLeft soft keyApplicationswitch keyMenu access/confirm keyDelete keyAlphanumeric keysExternal displayInfrared portSpecialfunction keysRight soft keyt-zones keyPower On/Off/Menu exit keyExterior camera lens

7Get startedFirst steps to operating your phoneUSIM/SIM card informationWhen you subscribe to a cellular network, you receive a plug-in SIM (Subscriber Identity Module) card loaded with your subscription details, such as your PIN and available optional services. For 3G services, you can purchase a USIM (Universal Subscriber Identity Module) card.Install and charge the phone Remove the battery.If the phone is already on, first turn it off by holding [ ]. Insert the USIM/SIM card.Make sure that the gold-coloured contacts on the card face down into the phone.1 2 Install the battery. Plug the travel charger into the phone. Plug the charger into a standard AC wall outlet.The LED on the charger indicates the charging progress.• Red: the battery is being charged.• Green: the battery is completely charged.• Orange: the battery is not correctly installed or is operating at a too high or too low temperature. When the phone is completely charged (green charger LED), unplug the charger from the power outlet.3 456

Get started8Low battery indicatorWhen the battery is low:• a warning tone sounds,• the battery low message displays, and• the empty battery icon blinks.If the battery level becomes too low, the phone automatically turns off. Recharge your battery. Power on or off Remove the charger from the phone.7Power onDo not turn on the phone when mobile phone use is prohibited.1. Open the phone.2. Press and hold [ ] to turn on the phone.3. If necessary, enter the PIN and press <Confirm>.Power off1. Open the phone.2. Press and hold [ ].

Get started10DisplayLayoutThe display has three areas.IconsReceived signal strengthNetwork connection status• : 2.5G network• : Calling in 2.5G network• : 2.5G network is unavailable•: 3G network• : Calling in 3G network• : 3G network is unavailableActive roaming featureVoice call in progressOut of your service area; you cannot send or receive voice callsText and graphicsdisplays messages, instructions, and information you enter.Soft key function indicatorsshows the current functions assigned to the two soft keys.Iconsdisplays various icons.Msg. V-CallIcons (continued)Video call in progressOut of your service area; you cannot send or receive video callsBluetooth feature is active. When sending data, this icon is blinking red and blue.p. 68 Connected with a Bluetooth headset or hands-free kitIrDA port is activep. 69Memory card insertedConnected with a computerSynchronised with a phoneBrowsing the InternetConnected to a secured web pageNew message; depending on the message type, the following icons may appear.•: SMS• : MMS or MMS with attachments•: E-mail•: Voicemail•: WAP push• : Configuration message

11Get started Access menu functionsIcons (continued)Inbox full; depending on the message type, the following icons may appear.•: SMS• : MMS or MMS with attachments•: E-mail•: Voicemail•: WAP push• : Configuration messageProfile settingp. 31•: T-mobile•: Normal• : Meeting•: Car•: Silent• : OutdoorBattery power levelUse the soft keysThe roles of the soft keys vary depending on the function you are using. The bottom line of the display indicates their current role.In each main menu, one of the most popular sub menu is assigned to the left soft key. This allows you to quickly access the most popular menus.Press the left soft key to access the Messages menu.Press the right soft key to make a video call.Msg. V-Call

14Make/Answer callsStep outside the phoneBegin with your camera, Media player, games, WAP, and other special featuresUse cameraTo make a voice call:1. Enter an area code and phone number.2. Press [ ].3. To end the call, press [ ].To make a video call:1. Enter an area code and phone number.2. Press <V-Call>, and the other person appears on the screen.1. When the phone is ringing, press [ ].2. For a video call, press <Show me> to allow the other person to see you.3. To end the call, press [ ].Press [ / ].Make a callAnswer a callAdjust the volume during a call1. In Idle mode, press and hold [ ] to turn on the camera.2. Press [ ] to switch between the interior lens and exterior lens.3. Aim the camera lens at the subject and adjust the image.4. Press [OK] to take a photo. The photo is saved automatically.5. Press [OK] to take another photo.1. In Idle mode, press [OK] and select My Media → Photos.2. Select the photo you want.Take a photoView a photo

15Step outside the phone Play media files1. In Idle mode, press and hold [ ] to turn on the camera.2. Press [1] to switch to Record mode.3. Press [ ] to switch between the interior lens and exterior lens.4. Press [OK] to start recording.5. Press [OK] to stop recording. The video is automatically saved.6. Press [OK] to record another video.1. In Idle mode, press [OK] and select My Media → Videos.2. Select the video you want.Record a videoPlay a videoUse these methods:• Download from the wireless webp. 49• Download from a computer using EasyStudio II EasyStudio User’s Guide• Copy files to a memory card and insert the card into the phone.p. 20• Receive via IrDA or Bluetoothp. 69, p. 67.1. In Idle mode, press [ ].2. Press <Options> and select Open play list.3. Press <Options> and select Add → Folder or Files.4. Check the files you want or scroll to the folder you want.5. Press <Add> or <Select>.Copy media files to the phoneCreate a play list

Step outside the phone16Play gamesBrowse the webUsing a built-in WAP (Wireless Access Protocol) browser, you can get easy access to the wireless web to receive a variety of up-to-date information and services and to enjoy downloads of web contents.1. From the play list, press [OK].2. Press [OK] to start playing.3. During playback, use the following keys:•OK: Pauses or resumes playback.• Up: Opens the play list.• Left: Goes to the previous file. Moves backward in a file when held down.• Right: Skips to the next file. Skips forward in a file when held down.• / : Adjusts the volume.• Down: Stops playback.1. In Idle mode, press [OK] and select My Media → Games & More → the game you want.2. Press any key, except for [ ], to launch the game.1. Select Play.2. Select a character.3. Press <OK> to start a game.Play media filesSelect a gamePlay Powerinlinex1. Select START GAME.2. Select New Game.3. Press <Skip>, then <OK>.4. Press [OK] to start a game.In Idle mode, press [ ]. You are accessed to t-zones , which is the WAP service provided by T-mobile.• To scroll through browser items, press [Up] or [Down].• To select an item, press [OK].• To return to the previous page, press <Back>.• To use browser options, press <Options>.Play TheLastAgeLaunch the browserNavigate the web

17Step outside the phone Use ContactsTo the phone’s memory:1. In Idle mode, enter a phone number.2. Press <Options> and select Save contact to → Phone → New → a number type.3. Specify the contact information: First name, Last name, Email work, Email home, Group, Homepage, Birthday, and More information (Job title, Department, Company, Nickname, and Notes).4. Press <Options> and select Save to save the entry.To the USIM/SIM card:1. In Idle mode, enter a phone number.2. Press <Options> and select Save contact to → SIM → New.3. Specify the contact information: Name, Phone number, Group, Location number.4. Press <Save> to save the entry.Add an entry1. In Idle mode, press [OK] and select Contacts → Search contact.2. Select an entry.3. Select a number and press [] to dial, or [OK] to edit the contact information.1. In Idle mode, press [OK] and select Contacts → My name card.2. Specify your contact information.3. Press <Options> and select Save to save the name card.4. To send the name card to other people, access the My name card menu again. 5. Press <Options> and select Send name card → the sending method you want.Find an entryCreate and send your name card

Step outside the phone18Send messages1. In Idle mode, press <Msg.> and select Create new → Short msg..2. Enter the message text.3. Press [OK].4. Enter destination numbers.5. Press [OK] to send the message.1. In Idle mode, press <Msg.> and select Create new → Multimedia msg..2. Enter the message subject.3. Select Text.4. Enter the message text and press [OK].5. Select Picture or Audio.6. Add a media file.7. Press [OK].8. Enter destination numbers or e-mail addresses.9. Press [OK] to send the message.Send a text message (SMS)Send a multimedia message (MMS)1. In Idle mode, press <Msg.> and select Create new → Email.2. Enter the e-mail subject.3. Move to the Message field.4. Enter the e-mail text.5. Move to the Attach files line.6. Press <Options> and select Add files, Add name card, or Add v-calendar.7. Select images, videos, sounds, name cards, schedule items, or tasks.8. Press <Options> and select Attach.9. Press [OK].10.Enter e-mail addresses.11.Press [OK] to send the e-mail.Send an e-mail

19Step outside the phone View messagesUse Bluetooth wirelessYour phone is equipped with Bluetooth technology which enables you to connect the phone wirelessly to other Bluetooth devices and exchange data with them, talk hands-free, or control the phone remotely.When a notification appears:1. Press <View>. 2. Select a message from the Inbox.From the Inbox:1. In Idle mode, press <Msg.> and select Inbox.2. Select an SMS message ().When a notification appears:1. Press <View>.2. Press <Options> and select Retrieve. 3. Select a message from the Inbox.From the Inbox:1. In Idle mode, press <Msg.> and select Inbox.2. Select an MMS message ().View text messageView a multimedia message1. In Idle mode, press <Msg.> and select Email inbox.2. Press <Options> and select Download.3. Select an e-mail or header.4. If you selected a header, press <Options> and select Retrieve.In Idle mode, press [OK] and select Settings → Connectivity → Bluetooth → Activation → On.1. In Idle mode, press [OK] and select Settings → Connectivity → Bluetooth → My devices → Search new device.2. Select a device.View an e-mailTurn on BluetoothSearch for and pair with a Bluetooth device

Step outside the phone20Use a memory cardYou can use a memory card to enlarge your phone’s memory capacity.3. Enter a Bluetooth PIN code or the other device’s Bluetooth PIN code, if it has, and press <OK>.When the owner of the other device enters the same code, the pairing is complete.1. Access an application, Contacts, My items, or Organiser.2. Select the item you want to send.3. Press <Options> and select Send (name card) → Via bluetooth. 4. Select a device.5. If necessary, enter the Bluetooth PIN and press <OK>.To receive data via Bluetooth, your phone’s Bluetooth feature must be active.If necessary, press <Yes> to confirm the reception.Send dataReceive data• Frequent erasing and writing will shorten a memory card’s lifespan.• Do not remove a memory card from the phone or turn off the phone while data is being accessed or transferred. This could result in loss of data and/or damage to the card or phone.• Do not subject memory cards to strong shocks.• Do not touch memory card terminals with your fingers or metal objects. If dirty, wipe the card with a soft cloth.• Keep memory cards away from small children or pets.• Do not expose memory cards in a place subjects to electro static discharge and/or electrical noise.• Use the memory card supplied with your phone or ones purchased from a Samsung dealer.Important information

21Step outside the phone 1. Slide a memory card into the memory card slot on the right side of the phone, with the label side face down.2. Press the card until it locks into place.1. Press the memory card so that it is disengaged from the phone.2. Slide the card out of the slot.Insert a memory cardRemove the memory card

22Enter textABC, T9, Number, and Symbol modeYou can enter text for some features such as Messages, Phonebook, or Organiser, using ABC mode, T9 mode, Number mode, and Symbol mode.Changing the text input modeThe text input mode indicator displays when the cursor is in a text input field.• Press and hold [ ] to switch between T9 ( ) and ABC ( ) modes.• Press [ ] to change case ( / / ) or to switch to Number mode ( ).• Press and hold [ ] to switch to Symbol mode ().Using T9 modeT9 is a predictive text input mode that allows you to key in any character using single keystrokes.Entering a word in T9 mode1. Press [2] to [9] to start entering a word. Press each key once for each letter. For example, press [4], [3], [5], [5], and [6] to enter Hello in T9 mode. T9 predicts the word that you are typing, and it may change with each key that you press.2. Enter the whole word before editing or deleting characters.3. When the word displays correctly, go to step 4. Otherwise, press [0] to display alternative word choices for the keys that you have pressed. For example, Of and Me use [6] and [3].4. Press [ ] to insert a space and enter the next word.Tips for using T9 mode• Press [1] to enter periods or apostrophes automatically.• Press the Navigation keys to move the cursor. • Press [C] to delete characters one by one. Press and hold [C] to clear the entire display.Adding a new word to the T9 dictionaryThis feature may not be available for some languages.1. Enter the word that you want to add.2. Press [0] to display alternative words for your key presses. When there are no more alternative words, Spell displays on the bottom line. 3. Press <Spell>.4. Enter the word you want using ABC mode and press <Add>.

23Enter text Using ABC modePress the appropriate key until the character you want appears on the screen.Tips for using ABC mode• To enter the same letter twice or to enter a different letter on the same key, wait for the cursor to move to the right automatically or press [Right]. Then, enter the next letter.• Press [ ] to insert a space.• Press the Navigation keys to move the cursor. •Press [C] to delete characters one by one. Press and hold [C] to clear the entire display.Using Number modeNumber mode enables you to enter numbers. Press the keys corresponding to the digits you want.Using Symbol modeSymbol mode enables you to insert symbols.Upper case Lower caseKey Characters in order displayedTo Pressdisplay more symbols [Up] or [Down]. select a symbol the corresponding number key.clear the symbol(s) [C]. insert the symbol(s) <OK>.

24Call functionsAdvanced calling featuresMaking a call1. In Idle mode, enter the area code and phone number.2. Press [ ].Making an international call1. In Idle mode, press and hold [0]. The + character appears.2. Enter the country code, area code, and phone number, then press [ ].Redialling recent numbers1. In Idle mode, press [ ] to display the list of recent numbers.2. Scroll to the number you want and press [ ].Making a call from ContactsOnce you have stored a number in Phonebook, you can dial the number by selecting it from Phonebook.p. 50You can also use the speed dial feature to assign your most frequently called numbers to specific number keys.p. 52Dialling a number from the USIM/SIM card1. In Idle mode, enter the location number for the phone number you want and press [ ].2. Find the number you want.3. Press <Call> or [ ] to make a voice call, or <V-Call> to make a video call to the number.Ending a callPress [ ] or close the phone.Answering a callWhen you receive an incoming call, the phone rings and displays the incoming call image. Press [ ] or <Accept> to answer the call.Tips for answering a call• When Anykey answer is active, you can press any key to answer a call, except for [ ] and <Reject>.p. 64• When Active folder is active, you can answer a call by opening the phone.p. 64• Press <Reject> or [ ] to reject a call.• Press [C] to clear the last digit or press and hold [C] to clear the whole display. You can move the cursor to edit an incorrect digit.• Press and hold [] to enter a pause between numbers.

25Call functions Viewing missed callsIf you have missed calls, the screen displays how many calls you have missed.1. Press <View>.2. If necessary, scroll through the missed calls.3. Press [ ] to dial the number you want.Using the headsetUse the headset to make or answer calls without holding the phone. Connect the headset to the jack on the left side of the phone. The buttons on the headset work as listed below:Options during a callYou can access a number of functions during a call.Adjusting the volume during a callUse [ / ] to adjust the earpiece volume during a call.Press [ ] to increase the volume level and [ ] to decrease the volume level.Placing a call on hold/RetrievingPress <Hold> or <Unhold> to place the call on hold or retrieve the call.Making a second callYou can make another call if your network supports it.1. Press <Hold> to put the call on hold.2. Make the second call in the normal way.3. Press <Swap> to switch between the calls.4. Press <Options> and select End held call to end the call on hold.5. To end the current call, press [ ].Answering a second callYou can answer an incoming call while already on the phone, if your network supports it and you have activated the call waiting feature.p. 67 1. Press [ ] to answer the call. The first call is automatically put on hold.2. Press <Swap> to switch between the calls.3. Press <Options> and select End held call to end the call on hold.4. To end the current call, press [ ].Using the loudspeaker featureUse the speaker to talk and listen with the phone a short distance away. Press <Options> and select Loudspeaker, or press [OK].To Pressredial the last call the button twice.answer a call the button.end a call the button.

Call functions26Using a Bluetooth headsetUse an optional Bluetooth headset to talk on the phone without holding the phone to your ear. To use this feature, you first need to register your headset and connect it to the phone.p. 67Press <Options> and select Switch to headset. To switch the call back to the phone, press <Options> and select Switch to phone.Switching off the microphone (Mute mode)You can temporarily switch off your phone’s microphone so that the person on the phone cannot hear you.Press <Options> and select Mute. To turn the microphone back on, press <Options> and select Unmute.Muting or sending key tonesYou can turn the key tones off or on.Press <Options> and select Mute key tone or Unmute key tone.Using PhonebookYou can access the Contacts menu to locate or store contacts in Phonebook.p. 50Press <Options> and select Contacts.Sending an SMS messageYou can create and send an SMS message to other people as well as to your current call participants.Press <Options> and select Send short msg.p. 45Sending a sequence of DTMF tonesDual tone multi-frequency (DTMF) tones are the tones used in phones for tone dialling.You can send DTMF tones as a group after entering the entire number you need to send or retrieving a number from Phonebook. This feature is helpful for entering a password or an account number when you call an automated system, like a banking service.1. When connected with a teleservice system, press <Options> and select Send DTMF.2. Enter the number you need to send and press <Send>.Adding a memoYou can add a memo during a call. Press <Options> and select Memo.p. 50To communicate with answering machines or computerised telephone systems, Unmute key tone must be selected.

27Call functions Making a multi-party call Use this feature to allow as many as six people to join a multi-party call, or conference call.Your service provider must support multi-party calls for you to use this feature.Setting up a multi-party call1. Call the first participant.2. Call the second participant. The first call is automatically put on hold.3. Press <Options> and select Join. The first participant is added to the multi-party call.4. If desired, call another person or answer an incoming call.5. Press <Options> and select Join.6. Repeat steps 4 and 5 as desired.Having a private conversation with one participant1. Press <Options> and select Split. 2. Select a name or number from the participant list.You can talk privately with that person, while the other participants converse with each other.3. To return to the multi-party call, press <Options> and select Join.Dropping one participant1. Press <Options> and select Drop call. 2. Select a name or number from the participant list. The participant is dropped from the call, but the call continues with the other parties.3. Press [ ] to end the multiparty call.Using the video call featureIn a 3G (UMTS) service area, your phone can make or receive a video call which allows you to see another person on the screen during a conversation. The other person’s phone must support the video call feature.Making a video call1. In Idle mode, enter the area code and phone number.2. Press <V-Call>.Answering a video callWhen you receive a video call, answer a video call as receiving a voice call. Press <Show me> to allow the caller to see you.

28Using video call optionsDuring a video call, press <Options> to access the following options:•Loudspeaker/Loudspeaker off: turns the loudspeaker on or off.•Switch to headset/Switch to phone: switch the call to a Bluetooth headset or back to the phone.•Mute camera: turn the camera off.•Mute voice: mute the microphone.•Mute camera & voice: turn the camera off and mute the microphone.•Mute key tone: mute key tones.•Zoom: display the zoom control bar.•Brightness: display the brightness control bar.•Effects: change the colour tone of the image.•Hide information/Show information: hide or display information about the video call.•Send DTMF: send Dual tone multi-frequency (DTMF) tones as a group after entering the entire number you need to send or retrieving a number from Phonebook.•Video call conditions: change the image quality.•End call: end the video call.Menu functionsAll menu options listedMedia playerUse Media player to enjoy media files, such as video clips and music files. You can also play streaming contents. To access this feature, press [] in Idle mode.Downloading or receiving media filesUse this method to save media files to your phone:• Download from the wireless webp. 49• Download from a computer using EasyStudio II EasyStudio II User’s Guide• Receive via IrDA or Bluetoothp. 69, p. 67• Copy files to a memory card and insert the card into the phoneCreating the play listAdd the media files to the play list so you can play them.1. From the media player screen, press [OK].2. Press <Options> and select Add.3. Select Folder or Files. 4. Check the files you want or scroll to the folder you want.

Menu functions32Using image optionsWhile viewing an image, press <Options> to access the following options:•Send: send the image via MMS, e-mail, Bluetooth, or infrared port.•Hidden from bluetooth: hide the image so that other Bluetooth devices cannot access it.•Visible to bluetooth: share the image with other Bluetooth devices.•Set as: set the image as your wallpaper for the main display or external display, or a caller ID image for a Phonebook entry.•Move: move the image to another folder.•Copy: copy the image to another folder.•Real size: show the image in the real size.•Slide show: set all images to display as a slide show.•Edit: change the image properties.•Delete: delete the image.•Rename: change the name of the image.•Details: access information about the image.While viewing the image list, press <Options> to access the following options:•View: open the selected image.•Send: send the image via MMS, e-mail, Bluetooth or infrared port.•Hidden from bluetooth: hide the image so that other Bluetooth devices cannot access it.•Visible to bluetooth: share the image with other Bluetooth devices.•Set as: set the image as your wallpaper for the main display or external display, or as a caller ID image for a Phonebook entry.•Move: move the image to another folder.•Copy: copy the image to another folder.•Delete: delete the selected image or all images.•Rename: change the name of the image.•Lock: lock the image to prevent from being deleted.•New folder: add a new folder.•Memory status: access the memory information for each folder in My Media.•Key management: manage the license keys you have acquired.PicturesThis menu displays images downloaded or received in messages. You can access and use them the same as you would in the Photos folder.Downloading images1. From the Pictures folder, select More pictures. You are connected to the image download service provided by T-mobile.2. Search for an image and follow the onscreen instructions to download it.

33Menu functions My Media (OK 2)SoundsThis menu displays the sound files you have recorded, downloaded, or received in messages.Playing a sound clip1. Press [Left] or [Right] to scroll to a sound folder.In the Voice memos folder, you can access voice memos.p. 572. Select a sound clip. The sound is played.During playback, you can use the following keys:Using sound optionsDuring playback, press <Options> to access the following options:•Send: send the sound clip via MMS, e-mail, file messenger, Bluetooth, or infrared port.•Hidden from bluetooth: hide the sound clip so that other Bluetooth devices cannot access it.•Visible to bluetooth: share the sound clip with other Bluetooth devices.•Delete: delete the sound clip.•Rename: change the name of the sound clip.•Set as caller ID: set the sound clip as a caller ID ringer.•Details: access information about the selected sound clip.Downloading sounds1. From the Sounds folder, select t-music. You are connected to the t-music service of t-zones.2. Search for a sound and follow the onscreen instructions to download it.Games & MoreUse this menu to play or download Java games.Playing Powerinlinex1. From the Games & More menu, select Powerinlinex.2. Press any key, except for [ ].3. Select PLAY or press <Play>.4. Select a character.5. Press <OK> to start a game.Playing TheLastAge1. From the Games & More menu, select TheLastAge.Key DescriptionUp/Down//Adjusts the volume.Left Goes to the previous file.Right Skips to the next file.OKAllows you to send the sound clip to other people.During a game, press <Options> to access game options.

37Menu functions Call register (OK 3)Using call record optionsWhile viewing the call list, press <Options> to access the following options:•Details: access information about the selected call record.•Save contact to: save the selected number in Phonebook.•Voice call: place a voice call.•Video call: place a video call.•Use number: paste the selected number to the normal dialling screen.•Send message: send a message to the selected number using SMS, MMS, or file messenger.•Delete: delete the selected call record.•Delete all: delete all records.Dialled calls(OK 3.2)This menu displays the most recent calls you have dialled.Received calls(OK 3.3) This menu displays the most recent calls you have received.Current contacts (OK 3.4)This menu displays all of the calls you have dialled, received, or missed.Data calls (OK 3.5)Use this menu to view the total amount of sent or received data.To reset a counter or all of the counters, press <Options> and select Reset or Reset all.Calls cost(OK 3.6) This network feature displays the cost of calls. This menu is available only if your USIM/SIM card supports this feature. Note that this is not intended to be used for billing purposes.•Total costs: check the total cost of all your calls. If the total cost exceeds the maximum cost set in Edit cost limit, you must reset the counter before you can make another call.•Last call cost: check the cost of your last call.•Max cost: check the maximum cost set. Press <Options> to access the following options:•Reset call cost: reset the cost counters.•Edit cost limit: set the maximum cost authorised for your calls.•Setup currency: set the price per unit that is applied when the cost of your call is calculated.

Menu functions38Calls time(OK 3.7) This menu displays the time log for voice and video calls made and received. The actual time invoiced by your service provider will vary.• Total dialled: check the total length of voice calls dialled.• Total received: check the total length of voice calls received.• Total dialled: check the total length of video calls dialled.• Total received: check the total length of video calls received.To reset a counter or all of the counters, press <Options> and select Reset or Reset all.Messages (OK 4)Use the Messages menu to send and receive short text messages, multimedia messages, and e-mails. You can also use WAP push message, Voice mail, and Cell broadcast message features.To access this menu, press [OK] in Idle mode and select Messages, or press <Msg.> in Idle mode.Create new (OK 4.1)Use this menu to create and send text messages, multimedia messages, or e-mails. You can also send files using MMS.Short msg. (OK 4.1.1)Short Message Service (SMS) allows you to send or receive text messages.1. Enter your message. You can enter up to approximately 1800 standard characters, or 900 Unicode characters, such as ‘â’.Press <Options> and select Insert to retrieve a text template, contact entry, or bookmark.2. Press [OK].The maximum number of characters allowed in a short message varies by your service provider. If your message exceeds the maximum number of characters, the phone will split the message.

39Menu functions Messages (OK 4)3. Enter a destination number.To send the message to more than one recipient, press [Down] and fill in additional destination fields.4. Press [OK] to send the message.Multimedia msg. (OK 4.1.2) Multimedia Message Service (MMS) delivers messages containing a combination of text, image, video, and audio, from phone to phone or from phone to e-mail.1. Enter the message subject.2. Select the Text line.3. Enter the message text and press [OK].4. Select the Picture or Audio line.5. Select an image or audio file and press <Add>. 6. Press <Options> to access the following options:•Preview: display the message you created.•Edit text/Change file: edit the added text, picture, or sound clip.•Delete text/Delete file: delete the added text, picture, or sound clip.•Save to Drafts: save the message in the Drafts box.•Add page: add a page. Move to each page by pressing [Left] or [Right] on the message screen.•Move page: move the current page to the next or previous page.•Delete page: delete the added page.•Edit style: change the page properties.This page: set the page duration and change the font colour and style for the selected page.All page: change the background colour and page layout.•Save as template: save the message as a template in the MMS templates folder.7. Press <Options> and select Send.8. Enter a phone number or e-mail address.To send the message to more than one recipient, press [Down] and fill in additional destination fields.9. Press [OK] to send the message.File messenger (OK 4.1.3)Use this menu to send multiple media files by attaching them to an MMS message. 1. Enter a subject in the Subject line.2. Move to the Message field and enter the message text.3. Select the Attach files line.4. Press [OK] to check the files you want.The maximum size allowed for an MMS message can differ depending on the country. If you cannot attach another file, add another page.

Menu functions405. Press <Options> and select Attach.6. Press <Options> to access the following options:•Attached file list: display the file list you attached.•Add name card: add a contact as a Vcard format.•Add v-calendar: add a calendar memo.•Delete all attached files: delete all of attached files.•Save to Drafts: save the message in the Drafts box.7. Press <Options> and select Send.8. Enter a phone number or e-mail address.To send the message to more than one recipient, press [Down] and fill in additional destination fields.9. Press [OK] to send the message.Email (OK 4.1.4)You can send and receive e-mails that include text, audio, and images. To use this feature, you need to set up your e-mail account.p. 481. Enter the e-mail subject.2. Move to the Message field.3. Enter the message text.4. Select the Attach files line.5. Press [OK] to check the files you want.6. Press <Options> and select Attach.7. Press <Options> to access the following options:•Attached file list: display the file list you attached.•Add name card: add a contact as a Vcard format.•Add v-calendar: add a calendar memo.•Delete all attached files: delete all of attached files.•Save to Drafts: save the e-mail in the Drafts box.8. Press <Options> and select Send.9. Enter an e-mail address.To send the e-mail to more than one recipient, press [Down] and fill in additional destination fields. 10.Press [OK] to send the e-mail.Inbox (OK 4.2)This folder stores all types of messages you have received, except for e-mails: MMS, SMS, voicemail, WAP push messages from the WAP server, and configuration messages.Configuration messages, which are sent from your service provider, contains network parameters to let you easily apply the network settings to your phone.

41Menu functions Messages (OK 4)Viewing a message at the time of its receiptWhen a message has been received, the phone alerts you by:• Displaying a message icon and text notification• Sounding or vibrating, depending on the message alert settingTo read a message immediately, press <View>. To read it later, press <Exit>.For an MMS message, press <Options> and select Retrieve. The message is downloaded from the MMS server to the phone’s memory.Viewing a message in InboxOn the message list, the following icons are available depending on the message type:While viewing the message list, press <Options> to access the following options:•View: display the message.•Retrieve: retrieve the MMS message from the server.•Reject: reject the message.•Cancel retrieving: cancel retrieving an MMS message from the server.•Reply: send a reply to the sender.•Reply all: send a reply to the sender and all recipients.•Forward: forward the message to other people.•Install: apply the configuration value in the message to the phone.•Details: access information about the message.•Sort by: change the sort order of the message list.•Delete: delete the currently selected message.•Delete all: delete all messages.Using message optionsWhile viewing a message, press <Options> to access the following options:SMS messages•Reply: reply to the sender. •Forward: forward the message.•Call back: dial the phone number of the sender.•Save to Contacts: extract phone numbers or e-mail addresses from the message and saves them in Phonebook.• SMS • MMS• MMS notification • Configuration• WAP push • SIM• Depending on the DRM (Digital Rights Management), you may not be able to forward some messages. They are indicated by the icon.• An ! icon shows that a message was sent with high priority. A grey icon means that the message is of low priority.

Menu functions42•Move to SIM/Move to phone: move the message between the phone’s memory and the USIM/SIM card.•Delete: delete the message.MMS notifications/messages•Retrieve: retrieve the message from the server. This option is only available when you select a MMS notification.•Play: play the message.•Call/Go to URL/Go to RTSP: dials the highlighted phone number or access the highlighted web link.•Add to bookmarks: save the highlighted web link to the bookmark list.•Create e-mail: send an e-mail to the highlighted e-mail address.•Create multimedia message: send an e-mail to the highlighted e-mail address.•Reply: send a reply to the sender.•Reply to all: send a reply to the sender and all of recipients.•Forward: forward the message to another person.•Send to Album: send the message to the online media album provided by T-mobile.•Call back: dial the phone number of the sender.•Save as template: save the message as a template in the MMS templates folder.•Save files: save media items from the message into your phone’s memory or the memory card.•Save to Contacts: extract phone numbers or e-mail addresses from the message and save them in Phonebook.•Delete: delete the message.•Details: access information about the message.WAP push messages•Go to URL: connect to the URL specified in the message.•Delete: delete the message.Drafts (OK 4.3)This folder stores messages you have saved to send them at a later time while creating the message. On the message list, press <Options> to access the following options:•View: open the selected message.•Edit: edit the selected message.•Send: send the selected message.•Sort by: change the sort order of the list.•Delete: delete the selected message.•Delete all: delete all messages.

43Menu functions Messages (OK 4)Outbox (OK 4.4)This folder stores messages you have tried to send or have being sent. The following icons on the message icons indicates the sending status:• indicates the message is being sent. • indicates the message is failed to send.While viewing the message list, press <Options> to access the following options:•Edit: edit the selected message.•Send again: resend the message.•Cancel sending: cancels sending the message.•Sort by: change the sort order of the list.•Delete: delete the message.•Delete all: delete all messages.Sentbox (OK 4.5)This folder stores messages that you have sent successfully. While viewing the message list, press <Options> to access the following options:•View: open the selected message.•Send again: resend the message.•Forward: forward the message to other people.•Sort by: change the sort order of the list.•Delete: delete the message.•Delete all: delete all messages.Email inbox (OK 4.6)This folder stores e-mails that you have received.Viewing received e-mails1. From the e-mail folder, press <Options>.2. Select Download to get new e-mails from your server.The phone checks for new e-mails and retrieve received e-mails. The icons tell you the status of each e-mail:• : Retrieved e-mail• : Retrieved e-mail with attachments.• : E-mail not retrieved3. Select an e-mail or header.4. If the e-mail has more than one page, press [ / ] to scroll through pages one by one. 5. Select an attached file to view or play it.Using e-mail optionsWhile viewing the e-mail list or an e-mail, press <Options> to access the following options: •View: open the selected e-mail.• Depending on the DRM (Digital Rights Management), you may not be able to forward some messages. They are indicated by the icon.• An ! icon shows that an e-mail was sent with high priority. A grey icon means that the e-mail is of low priority.

Menu functions44•Retrieve: retrieve the body of the selected e-mail header from the e-mail server.•Reply: send a reply to the sender.•Reply to all: send a reply to the sender and all recipients.•Forward: forward the e-mail.•Download: download new e-mails or headers from the e-mail server.•Sort by: change the sort order of the list.•Save to contacts: extract phone numbers ore-mail addresses from the e-mail and save them in Phonebook.•Block: add the sender’s e-mail address or e-mail subject to the Block list.•Delete from phone: delete the selected e-mail or all e-mails from the phone’s memory.•Delete permanently: delete the selected e-mail or all of e-mails from both the phone’s memory and the e-mail server.•E-mail accounts: change the active e-mail account.•Details: access information about the e-mail.Templates(OK 4.7)Use this menu to create, edit, and send text templates and MMS templates.Text templates (OK 4.7.1)Use this menu to preset frequently used messages.Press <New> to create a new text template.From the text template list, press <Options> to access the following options:•Send: send the template as an SMS, MMS, file messenger, or e-mail.•New: add a new template.•Edit: change the selected template.•Delete: delete the template.•Delete all: delete all templates.Multimedia templates (OK 4.7.2)When you access this menu, you can view the list of templates you have saved.From the MMS template list, press <Options> to access the following options:•View: open the template message.•Send: send the template as an MMS message.•New: add a new template.•Edit: change the selected template.•Delete: delete the template.•Delete all: delete all templates.

Menu functions46Character support: select a character encoding type. If you select Automatic, the phone switches the encoding type from GSM-alphabet to Unicode if you enter a unicode character. Use of unicode encoding will reduce the maximum of number in a message to about half. If this menu is not shown, your phone provides the Automatic encoding by default.Multimedia message (OK 4.0.2)You can configure default MMS settings.•Sending options: set up the following options for sending MMS messages:Priority: set the priority level of your messages.Expiration: set the length of time your messages are stored in the MMS centre while attempts are made to deliver them.Delivery: set a time delay before messages are sent.Hide address: set your address to be hidden from the recipient’s phone.Request delivery report: set the network to inform you when your message has been delivered.Request read report: determine whether or not the phone sends a read-report request to a message’s recipient.Keep a copy: leave the copies of your messages in the Sentbox folder after sending.Add my name card: allow your contact information to be attached to your messages.Add signature: edit and attach your signature to messages via the file messenger.•Receiving options: set up the following options for receiving MMS messages:Home network: determine if your phone retrieves new messages automatically when you are in your home service area.Roaming network: determine if your phone retrieves new messages automatically when you are roaming in another network.Home reception and Roaming reception have the following options:- Auto download: The phone automatically retrieves messages from the server.- Manual: The phone displays notifications. Use the Retrieve option to manually download new messages.- Restricted: The phone displays a new message icon without notifications when you receive a new message.- Reject: The phone rejects all messages.Send delivery report: send a delivery report from the network to a sender.Send read report: determine whether or not the phone sends a read-report to a sender.Reject anonymous: reject messages from anonymous senders.Reject advertisement: reject advertisements.

Menu functions48•Email accounts: select an account to be used and set up e-mail accounts. Press <Options> and select Edit to access the following options:Account name: enter a name for the currently selected account.SMTP server: enter the IP address or domain name of the outgoing e-mail server.SMTP port: enter the SMTP port number.Use SSL: activate the use of the SSL (Secured Sockets Layer) protocol.Retrieving server type: select the protocol for the incoming e-mail server. The remaining options depend on the protocol type setting.POP3 server/IMAP4 server: set the POP3 or IMAP4 server address.POP3 port/IMAP4 port: set the POP3 or IMAP4 port number.Use SSL: activate the use of the SSL (Secured Sockets Layer) protocol.IMAP4 retrieving option: (only for IMAP protocol): set whether the phone retrieves only new messages or all messages.Retrieving option: set which part of e-mails the phone retrieves from the server.Keep in server: set to leave the copies of retrieved e-mails on the server. My address: set your e-mail address.User name: set the user name for SMTP/POP3/IMAP4 server connection.Password: set the password for SMTP/POP3/IMAP4 server connection. Voice mail (OK 4.0.4)You can change the number of the voicemail centre.Push message (OK 4.0.5)You can determine whether or not your phone receives push messages.Broadcast (OK 5.0.6)Use this menu to change the settings for the broadcast message service. •Receive: enable or disable the reception of broadcast messages.•Channel: specify the channels from which you receive broadcast messages.When you select Respective channels, you can set up a list of active CB channels.•Language: select the languages in which broadcast messages display.Memory status(OK 5. )Use this menu to view the memory status for SMS, MMS, e-mail, and push messages.

49Menu functions t-zones (OK 5)t-zones (OK 5)The Wireless Application Protocol (WAP) browser on your phone allows you to access the wireless web. Using the WAP browser, you can access up-to-the-minute information and a wide variety of media contents, such as wallpapers, ring tones, and music files.To access this menu, press [OK] in Idle mode and select t-zones, or press [ ].This connects your phone to the network and loads the homepage of the wireless web service provider. Navigating the WAP browserIn the WAP browser:Using WAP page optionsFrom any WAP page, press <Options> to access the following browser options:•Cancel: cancel your selection.•Go to homepage: send you back to the homepage.•Reload: reload the current page with updated information.•History: show URLs previously visited.•Send link: send the URL of the current page via SMS, e-mail, or file messenger.•Save: save the image of the current WAP page or the current page.•Advanced: clear browser information and access the browser settings.Copy text: copy the highlighted text.Search text: search for a specific word or phrase from the current WAP page.Clear history: delete the URLs stored in the history.Clear cookies: delete cookies.Clear cache: delete information stored in the cache.Details: access information about the current page.Browser settings: change the settings for the browser display, security, and certificates.Exiting the WAP browserPress [ ] to exit the browser.To Pressscroll through browser items [Up] or [Down]. select a browser item [OK].return to the previous page <Back>.

Menu functions50Contacts (OK 6)You can store phone numbers on your USIM/SIM card and in your phone’s memory. The USIM/SIM card and phone’s memory are physically separate, but they are used as a single entity called Phonebook. In the Contacts menu, you can manage your Phonebook entries.To access this menu, press [OK] in Idle mode and select Contacts.Search contact (OK 6.1)Use this menu to search for numbers in Phonebook.Finding an entry1. Enter the first few letters of the name that you want to find.2. Select the name you want from the list.3. Press [ ] to dial the number, or [OK] to edit the contact information.Using contact optionsWhile viewing the contact list, press <Options> to access the following options:•Details: access detailed information about the currently selected contact.•Edit: edit the contact information.•Video call: make a video call.•New: add a new contact.•Delete: delete the selected contact.•Search groups: access the caller group list.•Delete all: delete all contacts.While viewing details of a contact, press <Options> to access the following options:•Edit: edit the contact information.•Send message: send a message to the selected number using SMS, MMS, or file messenger.•Special options: set the following options:Picture: assign a caller ID image to alert you to a call from the number.Ring tone: assign a ringer melody to alert you to a call from the number.Msg. alert tone: select a tone to alert you an incoming message from the number.•Add to speed dial: set the selected number as a speed dial number.•Video call: make a video call.•Copy to SIM/Copy to phone: copy the contact to the phone’s memory or USIM/SIM card or vice versa.•Send name card: send the contact via e-mail, SMS, file messenger, Bluetooth, or infrared port. •Use number: paste the number to the normal dialling screen.•Delete: delete the contact.

51Menu functions Contacts (OK 6)New contact (OK 6.2)Use this menu to add a new contact to Phonebook.Storing a number in the phone’s memory1. Select Phone.2. Press [Down] and change the settings or enter information about the contact.•First name/Last name: assign a name.•Phone number: add a mobile phone number.•Email work: assign a business e-mail address.•Email home: assign a personal e-mail address.•Group: assign a caller group.•Homepage: enter a homepage address.•Birthday: enter the person’s birthday.•More information: enter the job title, department, company, nickname, and additional note about the person.3. Press <Options> and access the following options to add additional information:•Special options: assign a caller ID image, call ringer, or message ringer for the contact.•Add item: add a number category to the contact.•Change type: change the type of the selected number.•Mark video call: set the selected number as a video call number.4. Press <Options> and select Save.Storing a number on the USIM/SIM card1. Select SIM.2. Press [Down] and change the settings or enter information about the contact.•Name: assign a name.•Phone number: add a mobile phone number.•Group:assign a caller group.•Location number: change the location number.3. Press <Options> and select Save.Groups (OK 6.3)Use this menu to organise your contacts in caller groups.Adding members to a caller group1. Select a group.2. Press [OK] to check the contacts you want.3. Press <Save>.Managing caller groupsFrom the group list, press <Options> to access the following options:•View members: display the members of the select group.•Add member: add contacts to the selected group.

Menu functions52•Add group: add a new group.•Rename group: change the group name.•Delete group: delete the selected group. •Delete all groups: delete all groups, including the default groups.Speed dial (OK 6.4)Use this menu to assign speed dial numbers (2 to 9) to eight of your most frequently called numbers.Assigning speed dial entries1. Select a key location from 2 to 9. Key 1 is reserved for your voice mail server.2. Select the contact you want from the contact list.3. Scroll to a number, if it has more than one number.4. Press <Select>.Managing speed dial entriesWhile viewing the Speed dial screen, press <Options> to access the following options:•Add: assign a number to an unassigned key.•Details: display details about the speed dial entry.•Video call: make a video call.•Change: assign a different number to an assigned key.•Remove: clear the speed dial setting.Dialling speed dial entries Press and hold the appropriate key in Idle mode.My name card(OK 6.5)Use this menu to create your name card and send it to other people.Saving your name cardThe procedure for creating your name card is the same as the one for saving a number in the phone’s memory.p. 51 Using name card optionsAfter saving your name card, press <Options> to access the following options:•Edit: edit the name card. •Send name card: send the name card via e-mail, SMS, file messenger, Bluetooth, or infrared port.•Delete: delete the name card.Copy all (OK 6.6)Use this menu to copy all of the contacts stored on the USIM/SIM card to the phone’s memory, or vice versa.

Menu functions54Stopping an alarmWhen the alarm sounds, choose either of the following options to stop the alarm:•Press <OK> to confirm the alarm.•Press <Snooze> to stop the wake-up alarm for 5 minutes. You can do this a maximum of 5 times.Deactivating an alarm1. Select the alarm you want to deactivate.2. Select Off on the Alarm line.3. Press <Options> and select Save.Viewing missed event alarmsWhen you are unable to acknowledge an alarm for a scheduled event or anniversary, the phone stores the event alarms until you confirm them.1. From the Alarm list, select Missed event alarm.2. Select an event.3. Press <Confirm> to confirm and delete the event.Calendar (OK 7.2)Use this menu to keep track of your monthly schedule.Consulting the calendarWhen you open the calendar, today’s date is marked with a grey box. Scroll to the date you want. You can move to the next or previous month by pressing [/].Press <Options> to access the following options:•View: display the stored events for that date.•New: add a new event, anniversary, task, or memo. You can schedule up to 100 schedule items, 50 anniversaries, 20 tasks, and 20 memos on the calendar, and schedule more than one event per day.•Week view: display the week view screen.•Go to today: display the current date.•Go to date: display a specific date.•Starting day: set whether the calendar starts with Sunday or Monday.•Delete: delete the events for a specific period.•Delete all: delete all of the events in the calendar.Entering a new schedule item1. Select a date on the calendar. 2. Press <Options> and select New → Schedule.

55Menu functions Organiser (OK 7)3. Press [Down] and enter information or change the settings in the following entry fields:•Title: enter the title of the event.•Details: enter the event details.•Start/End: enter the starting or ending times for the event.•Start date/End date: enter the starting or ending dates for the event.•Location: enter information about the event location. •Alarm: select to set an alarm for the event and set the time for the alarm.•Repeat: select to set the event to recur. You can select a repeat unit and set the date to end repeating.•Expiry: set when the event will be deleted from the calendar. 4. Press <Options> and select Save.Entering a new anniversary1. Select a date on the calendar.2. Press <Options> and select New → Anniversary.3. Press [Down] and enter information or change the settings in the following entry fields:•Occasion: enter information about the anniversary.•Date: enter the date.•Alarm: select to set an alarm for the anniversary. You can set the number of days before the event date and the time for the alarm to sound.•Repeat every year: select to set the phone to remind you of the anniversary every year.4. Press <Options> and select Save.Entering a task1. Select a date on the calendar.2. Press <Options> and select New → Task.3. Press [Down] and enter information or change the settings in the following entry fields:•Title: enter the title for the task.•Task: enter the task content.•Start date: enter the starting date.•Due date: enter the ending date.•Priority: select a priority level.4. Press <Options> and select Save.Entering a memo1. Press <Options> and select New → Memo.2. Enter the memo text and press [Down].3. Enter the date and press [OK].

Menu functions56Viewing an eventSquare brackets on a calendar date indicate the type of events scheduled for that day:1. Select a date on the calendar to display the events for that day. The list of events displays.The following icons indicate the type of event:2. Select an event to view its details.Using event optionsFrom the event list, press <Options> to access the following options:•View: access the selected event.•New: add a new event.•Completed: change the status of the selected task.•Month view: switch to the month view screen.•Week view: switch to the week view screen.•Change date, Change due date, Reschedule: change the date of the event.•Delete: delete the selected event.•Delete all: delete all of the events for the selected day.•Send schedule/Send task: send the event via SMS, e-mail, file messenger, Bluetooth, or infrared port.•Send memo: send the memo via SMS.Week view(OK 7.3)Use this menu to view events for the selected week. The current date and the time cell with events marked in grey. Square brackets on a calendar date indicate the types of events scheduled for that day.1. Scroll up to the date line and press [Left] or [Right] to access another week.2. Select the time cell that contains the event you want.Today’s events(OK 7.4)Use this menu to view events for the selected date.Select an event to view its details. The event opens in Edit mode.Schedule(OK 7.5)This menu displays the scheduled events. If you have set the Repeat and Alarm options, the and icons display. Select a schedule item to view its details.• Green: schedule • Red: anniversary• Blue: task • Orange: memo• Scheduled events • Anniversaries• Tasks • Memos

57Menu functions Organiser (OK 7)Anniversary (OK 7.6) This menu displays anniversaries you have created. If you have set the Repeat and Alarm options, the and icons display. Select an anniversary item to view its details.Task(OK 7.7)Use this menu to display tasks you have created. The icons on the right indicate the importance; the lower the number on the icon, the higher the priority. A check mark appears in the status check box if the task has been completed. Select a task to view its details.Memo(OK 7.8)This menu displays memos you have created.Select a memo to view its details. Voice memo(OK 7.9)Use this menu to record voice memos.Recording a voice memo1. Press [OK] to start recording. 2. Speak into the microphone.Press [OK] to pause or resume the recording.3. When you have finished, press <Stop>. The voice memo is automatically saved.Playing a voice memo1. From the voice recorder screen, press <Options> and select Go to sounds.2. Press [Left] to scroll to Voice memo.3. Select a voice memo. The memo plays.On the player screen, you can use the following keys: Using voice memo optionsFrom the player screen, press <Options> to access the following options:•Play/Resume: play the voice memo or resume playback.•Stop: stop playback.•Record: record a new voice memo.•Send: send the voice memo via MMS, e-mail, file messenger, Bluetooth, or infrared port.Key FunctionOKPauses or resumes playback.Up Switches to Play mode () or back to Record mode ( ).Left Moves backward in a file when held down.Right Skips forward in a file when held down./ Adjusts the volume.Down Stops playback.

Menu functions58•Go to sounds: display the list of voice memos you have recorded.•Rename: change the name of the voice memo.•Delete: delete the selected voice memo.•Hidden from bluetooth: hide the voice memo so that other Bluetooth devices cannot access it.•Visible to bluetooth: share the voice memo with other Bluetooth devices.•Details: access information about the selected voice memo. •Record settings: change the default settings for recording a voice memo.Default name: change the default prefix of the voice memo.Recording time: select a maximum recording time.World clock(OK 7.0)Use this menu to set your local time zone and find out what time it is in another part of the world. Setting your local time zone1. From the world map, press [Left] or [Right] to select the city that corresponds to your home time zone. As the time line moves, the time and date of the given zone display.2. Press [OK] to save the time zone.Viewing and setting a foreign time zone1. From the world map, press [Down].2. Press [Left] or [Right] to select the foreign time zone you want to view.3. Press [OK] to save the time zone.Applying Daylight Savings Time1. From the world map, press <Options> and select Summer time.2. Press [OK] to check the time zone(s) you want. 3. Press <Select>.4. Press [OK].Math(OK 7. )This menu provides you with the math applications to let you do simple calculations and unit conversions.Calculator(OK 7. .1) Use this menu to perform basic arithmetic functions such as addition, subtraction, multiplication, and division.Preforming a calculation1. Enter the first number. Press [ ] to include a decimal point.2. Enter the operation for your calculation by pressing the Navigation keys.3. Enter the second number.4. Press [OK] to view the result.

59Menu functions Organiser (OK 7)Using calculator optionsPress <Options> to access the following options:•Equal: view the result.•Recent calculation: display the last result you calculated.•Save to memory: save a value into the calculator memory.•Recall memory: retrieve the saved value.•Clear memory: clear the saved values.Converter(OK 7. .2)Use this menu for common conversions, such as currency and temperature.Preforming a conversion1. Select the converter type you want.2. Press [Left] or [Right] to select the original unit and press [Down].3. Enter the value to be converted.• Press [ ] to insert a decimal point.• Press [ ] to change the temperature to above zero (+) or below zero (-).4. Press [Down].5. Press [Left] or [Right] to select the unit you want to convert to.The equivalent value for the amount you entered displays.Using converter optionsPress <Options> to access the following options:•Clear: clear the current values.•Reverse: reverse the conversion.•Currency rates: access and edit the currency rate list.Memory status (OK 7. )This menu displays the number of events of each type you have created, and the total number of events you can store.

Menu functions60Camera (OK 8)You can use the camera module embedded in your phone to take photos and record videos. Using the Camera menu, you can turn on the camera and manage your photos and video clips.To access this menu, press [OK] in Idle mode and select Camera, or press and hold [ ]. Taking a photoThe camera will produce JPEG photos.1. To turn on the camera, access the Camera menu or press and hold [ ].2. Press [ ] to switch between the interior lens below the display and the exterior lens on the external of the phone.3. Adjust the image by aiming the lens at the subject.• Press <Options> to use the camera options. See the next section.• Use the keypad to change the camera settings or switch to other modes.p. 614. Press [OK] to take a photo. The photo is saved in the My photos folder.Using camera options in Capture modeIn Capture mode, press <Options> to access the following options:•Take photo: take a photo.•Record video: switch to Record mode.•Switch camera: switch between the interior lens and the exterior lens.•Go to photos: display the photos stored in the My photos folder.p. 31•Shooting mode: take a photo in the following modes:Single shot: take a photo in the normal mode.Multi shot: take several action stills. You can select the number of shots.• Do not take photos of people without their permission.• Do not take photos in a place where cameras are not allowed.• Do not take photos in a place where you may interfere with another person’s privacy.When you take a photo in direct sunlight or in bright conditions, shadows may appear on the photo.Hold the phone still for one or two seconds after pressing the camera shutter key to allow the image data to process.5.To Pressuse photo options <Options>.p. 62delete the photo <Delete> or [C].return to Capture mode [OK].

61Menu functions Camera (OK 8)Mosaic shot: take several stills and saves them in one frame. Select the number of still images the camera will take.•Effects: change the colour tone of the image.•Frames: apply a decorative frame.•Flash: set the flash setting.•Timer: set a time delay before the camera takes a photo.•Zoom: display the zoom control bar.•Brightness: display the brightness control bar.•Camera settings: change the default settings for taking a photo.Default name: change the default prefix of the file name.Default storage: select a memory location to store photos.Viewfinder: select a preview mode, either Full Screen mode or Normal mode with actual radio.Shutter sound: select a camera shutter sound.Capture quality: select an image quality. Image size: select an image size. Multi shot speed: select the shutter speed between each shot in Multi Shot mode.Spot metering: adjust the exposure based on a specific area of the image. Select On to display the spot focus frame in the middle of the image, and change the exposure according to the brightness of the image fragment in the frame.ISO: change the ISO setting, which controls the sensitivity of your camera. For low light situations, lower the ISO number to increase the quality. The higher the ISO number, the faster the camera shutter functions and the more sensitive the camera is to light. Higher ISO settings may bring some distortion to an image.White balance: adjust the colour balance of the photo. You can make your photo appear warmer or cooler.Using the keypad in Capture modeYou can use the keypad to customise your camera settings in Capture mode.Key FunctionFlips the image vertically.Shows the mirror image.Left/Right Adjusts the brightness of the image.Up/Down Zooms in or out.1Switches to Record mode.p. 622Changes the image size.3Changes the image quality.

Menu functions62Using photo optionsAfter saving a photo, press <Options> to access the following options:•Viewfinder: return to Capture mode.•View: open the selected photo when you take multiple photos.•Send: send the photo via MMS, e-mail, file messenger, Bluetooth, or infrared port.•Delete: delete the photo.•Set as: set the photo as your wallpaper for main or external display, or as a caller ID image for a Phonebook entry.•Go to photos: display the photos stored in the My photos folder.p. 31•Rename: change the name of the photo.Recording a videoYou can use your phone just like a camcorder to record what is currently displayed on the camera screen and save it as a video file. The camera will produce 3gp video clips.1. To turn on the camera, access the Camera menu or press and hold [ ].2. Press [1] to switch to Record mode.3. Press [ ] to switch between the interior lens below the display and the exterior lens on the external of the phone.4. Adjust the image by aiming the lens at the subject.•Press <Options> to use the camera options.p. 63• Use the keypad to change the camera settings or switch to other modes.p. 635. Press [OK] to start recording.To pause, press <Pause>.6. When you have finished, press [OK]. The video automatically saves in the My videos folder.4Changes the shooting mode and the number of photos.5Changes the colour tone of the image.7Adds a decorative frame.8Sets the timer.9Goes to the My photos folder.p. 31Changes the preview mode.0Turns the flash on or off.Key Function7.To Pressreturn to Record mode [OK].use the video options <Options>.p. 63delete the video clip <Delete> or [C].

63Menu functions Camera (OK 8)Using camera options in Record modeIn Record mode, press <Options> to access the following options:•Record: start recording.•Take photo: switch to Capture mode.•Switch camera: switch between the interior lens or exterior lens.•Go to videos: display the video clips stored in the My videos folder.p. 34•Effects: change the colour tone of the image.•Zoom: display the zoom control bar.•Brightness: display the brightness control bar.•Video settings: change the following settings for recording a video:Default name: change the default prefix of the video name.Default storage: select a memory location to store video clips.Quality: select an image quality. Recording time: select a video recording mode.Select Normal to record a video within the limit of the currently available memory. The length of your video is determined by how much memory has been used.Select Limit for MMS to record a video suitable for an MMS message.Size: select an image size.Audio record: record audio with a video clip.Using the keypad in Record modeUsing video optionsAfter saving a video clip, press <Options> to access the following options:•Play: play back the video clip.•Viewfinder: return to Record mode.•Send: send the video clip via MMS, e-mail, file messenger, Bluetooth, or infrared port.•Delete: delete the video clip.Key FunctionFlips the image vertically.Shows the mirror image.Left/Right Adjusts the image brightness.Up/Down Zooms in or out.1Switches to Capture mode.p. 602Changes the frame size.3changes the image quality.4Changes the video recording mode.5Changes the colour tone of the image.7Turns the audio on or off.9Goes to the My videos folder.p. 340Turns the flash on or off.

65Menu functions Settings (OK 9)Display(OK 9.4)Use this menu to change settings for the display and the light.Greeting message (OK 9.4.1)Use this menu to enter the greeting that is displayed on the main display.Wallpaper(OK 9.4.2)You can change the background image that is displayed on the main display in Idle mode.Cover LCD (OK 9.4.3)Use this menu to change the settings for the external display.1. Select a display item type.•Clock: you can select a clock type.•Cover title: you can set a banner message.•Wallpaper: you can select a wallpaper image.2. Select the image you want or enter the banner message.For Wallpaper, you can select a section of an image.3. Press <Save> or [OK].4. Press <Change>.LCD brightness (OK 9.4.4)Use this menu to adjust the brightness of the main display.Backlight(OK 9.4.5) You can select the length of time the backlight and the display stays on.•On: select the length of time the backlight stays on in times of inactivity.•Dim: select the length of time the display is in Dimming mode after the backlight turns off. Dialing display (OK 9.4.6)Use this menu to customise the settings for the screen when entering a phone number for dialling.•Font size: select a font size.•Font colour: select a font colour.•Background colour: select a background colour for the dialling screen.Call(OK 9.5)Use this menu to set options for call functions.Caller ID(OK 9.5.1)Use this menu to prevent your phone number from being displayed on the phone of the person being called. Some networks do not allow the user to change this setting.

Menu functions66•By network: use the default setting provided by the network.•Send: send your number each time you make a call.•Hide: ensure your number does not display on the other person’s phone.Diverting(OK 9.5.2)This network service reroutes incoming calls to a different phone number that you specify.1. Select the type of calls to be diverted.2. Select a call diverting option:•Always: divert all calls.•Busy: divert calls when you are on another call.•No reply: divert calls when you do not answer the phone.•Unreachable: divert calls when you are not in an area covered by your service provider or when your phone is switched off.•Cancel all: cancel all of call diverting options.3. Enter the number to which the calls will be diverted in the Divert to line.4. If you selected No reply, move to the Waiting time line and select the length of time the network delays before diverting a call.5. Press <Options> and select Activate.To deactivate the call diverting, select Deactivate.Barring(OK 9.5.3)This network service allows you to restrict your calls.1. Select the type of calls to be barred.2. Select a call barring option:•All outgoing calls: prohibit all outgoing calls.•Outgoing int’l calls: prohibit international calls.•Int’l call exc. Home: only allow calls to numbers within the current country when you are abroad, and to your home country, defined as where your home network provider is located.•All incoming calls: prohibit incoming calls.•Incoming calls when roaming: prohibit incoming calls when you use your phone outside of your home country.•Cancel all: cancel all of the call barring settings, allowing calls to be sent and received normally.3. Enter the call barring password supplied by your service provider.4. Press <Options> and select Activate. To deactivate the call barring, select Deactivate.You can change the call barring password obtained from your service provider. From the call barring list, press <Options> and select Change password.

67Menu functions Settings (OK 9)Waiting(OK 9.5.4)This network service informs you when someone is trying to reach you while you are on another call.1. Select the type of calls to which the call waiting option will apply.2. Press <Options> and select Activate. To deactivate the call waiting, select Deactivate. Auto redial (OK 9.5.5)Use this menu to make up to ten attempts to redial a phone number after an unsuccessful call.Closed user group (OK 9.5.6)Use this menu to set incoming and outgoing calls to be restricted to a selected user group. For details about how to create a closed user group, contact your service provider.•Use user group: activate CUG index numbers.•Outside access: enable calls to numbers other than those in the Closed user group. This feature depends on the nature of your CUG subscription.•Default group: enable the default CUG, if you have set one with your service provider. When making a call, you are given the option of using your default CUG, instead of selecting one from the list.•Group index: add, delete, or activate CUG index numbers. Video call (OK 9.5.7)Use this menu to change the default settings for using the video call feature.•Show me: change the video camera settings for receipt of video calls.Optionally: you can select whether or not the video camera is used each time you answer a video call.Always: the camera is always used.•Retry by: set how to retry when the phone fails to make a video call, by MMS or voice call.Connectivity(OK 9.6)Use this menu to set options for connection available on your phone.Bluetooth (OK 9.6.1) Using Bluetooth wireless, you can connect the phone wirelessly to other Bluetooth devices and exchange data with them, talk hands-free, or control the phone remotely.Bluetooth technology allows free wireless connections between all Bluetooth-compliant devices within a range of 10 metres. Since the devices communicate using radio waves, they do not need to be in line of sight to each other.

Menu functions68Setting up the Bluetooth featureThe Bluetooth menu provides the following options:•Activation: activate or deactivate the Bluetooth feature.•My devices: search for connectable Bluetooth devices. See the next section.•My phone’s visibility: allow other Bluetooth devices to connect to your phone.•My phone’s name: assign a Bluetooth device name to your phone, which is then displayed on other devices.•Secure mode: determine if the phone asks for your confirmation when other devices access your data.•Bluetooth service: display available Bluetooth services. Searching for and pairing with a Bluetooth device1. From the Bluetooth setting options, select My devices.2. Select Search new device.After searching, a list of devices to which you can connect displays. The following icons indicate the kind of device:• Hands-free or headset• Mobile phone• Computer• PDA• Unknown deviceThe colour of the icon indicates the status of the device:• Grey for unpaired devices• Blue for paired devices• Red for devices that are currently connected to your phone3. Select a device.4. Enter a Bluetooth PIN code of up to 16 digits and press <OK>. This code is used just once and you don’t need to memorise it.When the owner of the other device enter the same code, pairing is finished.• You cannot use the Bluetooth feature while using multimedia features such as voice recorder, camera, and Media player, or vice versa.• Some devices may not be compatible with your phone.Some devices, especially headsets or hands-free car kits, may have a fixed Bluetooth PIN, such as 0000. If the other device has one, you must enter the code.

69Menu functions Settings (OK 9)Using device optionsFrom the device list, press <Options> to access the following options:•Connect: connect to the currently selected device. You need to enter the Bluetooth PIN.•Disconnect: end the connection with the device.•Browse device: search for data from the selected device and import data directly to your phone.•Authorize device/Unauthorize device: determine if the phone asks you to permit connection when other devices try to connect to your phone.•Delete: delete the device or all devices.•Rename: rename the selected device.Sending data via Bluetooth1. Activate the Bluetooth feature.2. Select the application in which the item you want to send is stored. 3. Scroll to the item you want and press <Options>.4. Select Send → Via bluetooth.The phone searches for devices within range and displays a list of available devices.5. Select a device.6. If necessary, enter the Bluetooth PIN needed for pairing and press <OK>.Receiving data via BluetoothTo receive data via Bluetooth, your phone’s Bluetooth feature must be active.If an unauthorised Bluetooth device sends data to your phone, the phone displays a confirmation message. To receive data, press <Yes>.Infrared (OK 9.6.2) Use this feature to send and receive data through the infrared port. To use an infrared connection, you must do the following:• Configure and activate an IrDA-compliant infrared port on the other device.• Activate the infrared feature on your phone; select Infrared → On.• Align the IrDA port on the phone with the IrDA port on the other device.If there is no communication between your phone and the other IrDA-compliant device within 60 seconds of activating the feature, it is automatically deactivated.

73Menu functions Settings (OK 9)To access a locked item or a related menu, you need to enter the phone password.Change PIN code(OK 9.8.7)Use this menu to change your PIN. The PIN Check feature must be enabled to use this feature.Change PIN2 code(OK 9.8.8)If supported by your USIM/SIM card, the Change PIN2 feature changes your current PIN2. Memory status(OK 9.9) Use this menu to check the amount of memory being used for storing data, such as SMS, MMS, Email, Push messages, My Media, Contacts, and Organiser items. You can also view the amount of shared memory or the memory card.Reset settings(OK 9.0) Use this menu to reset the phone to its default settings.1. Enter the phone password and press <Confirm>.2. Press <Yes>. The phone automatically turns itself off and then back on.Internet (OK 9. )Use this menu to use the WAP browser.Go to homepage (OK 9. .1)You can launch the WAP browser and access the homepage of the WAP service provided by T-mobile.Enter URL (OK 9. .2)You can enter the URL of the WAP page you want in order to quickly access the page.Favorites (OK 9. .3)You can add and manage the URLs of the WAP pages you frequently access as bookmark item. You can also manage URLs you have bookmarked while navigating the Internet.Adding a new bookmark1. Press New and select Favorites.2. Enter a URL and press [OK].3. Enter a name for the item and press <OK>.4. Press [OK] to save the item.Using boomark optionsFrom the bookmark list, press <Options> to access the following options:•Open: access the page of the selected bookmark.•Details: access the details of the bookmark item.The password is preset to 00000000. You can change this password p. 72

75“No service,” “Network failure,” or “Not done” displays• The network connection has been lost. You may be in a weak signal area. Move and try again.• You are trying to access an option for which you have no subscription with your service provider. Contact the service provider for further details.You have entered a number but it was not dialled• Be sure that you have pressed [ ].• Be sure that you have accessed the right cellular network.Your correspondent cannot reach you• Be sure that your phone is switched on. ([ ] pressed for more than one second.) • Be sure that you are accessing the correct cellular network.• Be sure that you have not set an incoming call barring option.Your correspondent cannot hear you speaking• Be sure that you have switched on the microphone.• Be sure that you are holding the phone close enough to your mouth. The microphone is located at the bottom of the phone.The phone starts beeping and “Battery low” flashes on the display• Your battery is insufficiently charged. Recharge the battery.The audio quality of the call is poor• Check the signal strength indicator on the display ( ). The number of bars indicates the signal strength from strong ( ) to weak ( ).• Try moving the phone slightly or moving closer to a window if you are in a building.No number is dialled when you re-call a Phonebook entry•Use the Search contact menu to ensure the number has been stored correctly.• Re-store the number, if necessary.If the above guidelines do not help you to solve the problem, take note of:• The model and serial numbers of your phone• Your warranty details• A clear description of the problemThen contact your local dealer or Samsung after-sales service.

125Health and Safety InformationExposure to Radio Frequency (RF) SignalsYour wireless phone is a radio transmitter and receiver.It is designed and manufactured not to exceed theemission limits for exposure to radio frequency (RF)energy set by the Federal Communications Commission(FCC) of the U.S. Government. These limits are part ofcomprehensive guidelines and establish permittedlevels of RF energy for the general population. Theguidelines are based on the safety standards that weredeveloped by independent scientific organizationsthrough periodic and through evaluation of scientificstudies.The standards include a substantial safety margindesigned to assure the safety of all persons, regardlessof age and health.The exposure standard for wireless phones employs aunit of measurement known as Specific AbsorptionRate (SAR). The SAR limit set by the FCC is 1.6W/kg *.*In the U.S. and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg)averaged over one gram of tissue. The standard incorporates a substantial margin of safety to giveadditional protection for the public and to account for any variations in measurements.safety-end-NorthA 1/27/03 2:05 PM Page 125

126HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn127HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonnSAR tests are conducted using standard operatingpositions specified by the FCC with the phonetransmitting at its highest certified power level in alltested frequency bands. Although the SAR isdetermined at the highest certified power level, theactual SAR level of the phone while operating can bewell below the maximum value. This is because thephone is designed to operate at multiple power levelsso as to use only the power required to reach thenetwork. In general, the closer you are to a wirelessbase station antenna, the lower the power output ofthe phone. Before a new model phone is available for sale to thepublic, it must be tested and certified to the FCC thatit does not exceed the limit established by thegovernment-adopted requirement for safe exposure.The tests are performed in positions and locations(e.g., at the ear and worn on the body) as required bythe FCC for each model. While there may bedifferences between the SAR levels of various phonesand at various positions, they all meet the governmentrequirement.The FCC has granted an Equipment Authorization for thismodel phone with all reported SAR levels evaluated as incompliance with the FCC RF exposure guidelines. SARinformation on this model phone is on file with the FCCand can be found under the Display Grant section ofhttp://www.fcc.gov/oet/fccid after searching on FCC IDprinted in the label on the phone.FCC certification information for this model phone isattached separation paper.For Body OperationTo maintain compliance with FCC RF exposure requirements, use only belt-clips, holsters or similar accessories that maintain a 1.5 cm. separation distance between the user's body and the back of the phone, including the antenna. The use of belt-clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy theserequirements may not comply with FCC RF exposurerequirements, and should be avoided. For more Information concerning exposure to radiofrequency signals, see the following websites:Federal Communications Commission (FCC) http://www.fcc.gov/rfsafetyCellular Telecommunications Industry Association (CTIA):http://www.wow-com.comU.S.Food and Drug Administration (FDA) http://www.fda.gov/cdrh/consumerWorld Health Organization (WHO) http://www.who.int/peh-emf/ensafety-end-NorthA 1/27/03 2:05 PM Page 126

129HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn• Do not leave the battery in hot or cold places, suchas in a car in summer or winter conditions, as youwill reduce the capacity and lifetime of the battery.Always try to keep the battery at roomtemperature. A phone with a hot or cold batterymay temporarily not work, even when the batteryis fully charged. Li-ion batteries are particularlyaffected by temperatures below 0 °C (32 °F).• Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object (coin,clip or pen) causes a direct connection betweenthe + and – terminals of the battery (metal stripson the battery), for example when you carry aspare battery in a pocket or bag. Short-circuitingthe terminals may damage the battery or theobject causing the short-circuiting.• Dispose of used batteries in accordance with localregulations. Always recycle. Do not dispose ofbatteries in a fire.Road SafetyYour wireless phone gives you the powerful ability tocommunicate by voice, almost anywhere, anytime.But an important responsibility accompanies thebenefits of wireless phones, one that every usermust uphold.When driving a car, driving is your first responsibility.When using your wireless phone behind the wheel ofa car, practice good common sense and rememberthe following tips.128HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonnPrecautions When Using Batteries• Never use any charger or battery that is damaged inany way.• Use the battery only for its intended purpose.• If you use the phone near the network’s basestation, it uses less power; talk and standby timeare greatly affected by the signal strength on thecellular network and the parameters set by thenetwork operator.• Battery charging time depends on the remainingbattery charge and the type of battery and chargerused. The battery can be charged and dischargedhundreds of times, but it will gradually wear out.When the operation time (talk time and standbytime) is noticeably shorter than normal, it is time tobuy a new battery.• If left unused, a fully charged battery will dischargeitself over time.• Use only Samsung-approved batteries and rechargeyour battery only with Samsung-approved chargers.When a charger is not in use, disconnect it from thepower source. Do not leave the battery connected toa charger for more than a week, since overchargingmay shorten its life.• Extreme temperatures will affect the chargingcapacity of your battery: it may require cooling orwarming first.safety-end-NorthA 1/27/03 2:05 PM Page 128

131HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn130HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn7. Do not engage in stressful or emotionalconversations that may be distracting. Make thepeople with whom you are talking aware that youare driving and suspend conversations that havethe potential to divert your attention from theroad.8. Use your wireless phone to call for help. Dial theemergency number in the case of fire, trafficaccident or medical emergencies. Remember, it isa free call on your wireless phone!9. Use your wireless phone to help others inemergencies. If you see a car accident, crime inprogress or other serious emergency where livesare in danger, call the emergency number, as youwould want others to do for you.10. Call roadside assistance or a special non-emergency wireless assistance number whennecessary. If you see a broken-down vehicleposing no serious hazard, a broken traffic signal,a minor traffic accident where no one appearsinjured, or a vehicle you know to be stolen, callroadside assistance or any other special non-emergency wireless number.1. Get to know your wireless phone and its features,such as speed dial and redial. If available, thesefeatures help you to place your call without takingyour attention off the road.2. When available, use a hands-free device. Ifpossible, add an extra layer of convenience andsafety to your wireless phone with one of themany hands-free accessories available today.3. Position your wireless phone within easy reach. Beable to access your wireless phone withoutremoving your eyes from the road. If you get anincoming call at an inconvenient time, let yourvoice mail answer it for you.4. Let the person you are speaking with know you aredriving; if necessary, suspend the call in heavytraffic or hazardous weather conditions. Rain,sleet, snow, ice and even heavy traffic can behazardous.5. Do not take notes or look up phone numbers whiledriving. Jotting down a To Do list or flippingthrough your phonebook takes your attention awayfrom your primary responsibility, driving safely.6. Dial sensibly and assess the traffic; if possible,place calls when you are not moving or beforepulling into traffic. Try to plan calls when your carwill be stationary. If you need to make a call whilemoving, dial only a few numbers, check the roadand your mirrors, then continue.safety-end-NorthA 1/27/03 2:05 PM Page 130

133HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn132HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonnWireless Technology Research.Persons with pacemakers:• Should always keep the phone more than 15 cm (6inches) from their pacemaker when the phone isswitched on• Should not carry the phone in a breast pocket• Should use the ear opposite the pacemaker tominimize potential interferenceIf you have any reason to suspect that interference istaking place, switch off your phone immediately.Hearing AidsSome digital wireless phones may interfere withsome hearing aids. In the event of such interference,you may wish to consult your hearing aidmanufacturer to discuss alternatives.Other Medical DevicesIf you use any other personal medical devices,consult the manufacturer of your device to determineif it is adequately shielded from external RF energy.Your physician may be able to assist you in obtainingthis information. Switch off your phone in health carefacilities when any regulations posted in these areasinstruct you to do so. Hospitals or health carefacilities may be using equipment that could besensitive to external RF energy.VehiclesRF signals may affect improperly installed orinadequately shielded electronic systems in motorvehicles. Check with the manufacturer or itsOperating EnvironmentRemember to follow any special regulations in forcein any area and always switch off your phonewhenever it is forbidden to use it, or when it maycause interference or danger.When connecting the phone or any accessory toanother device, read its user’s guide for detailedsafety instructions. Do not connect incompatibleproducts.As with other mobile radio transmitting equipment,users are advised that for the satisfactory operationof the equipment and for the safety of personnel, it isrecommended that the equipment should only beused in the normal operating position (held to your ear with the antenna pointing over your shoulder).Electronic DevicesMost modern electronic equipment is shielded fromradio frequency (RF) signals. However, certainelectronic equipment may not be shielded againstthe RF signals from your wireless phone. Consult themanufacturer to discuss alternatives.PacemakersPacemaker manufacturers recommend that aminimum distance of 15 cm (6 inches) be maintainedbetween a wireless phone and a pacemaker to avoidpotential interference with the pacemaker. Theserecommendations are consistent with theindependent research and recommendations ofsafety-end-NorthA 1/27/03 2:05 PM Page 132

135HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn134HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonnEmergency CallsThis phone, like any wireless phone, operates usingradio signals, wireless and landline networks as wellas user-programmed functions, which cannot guaranteeconnection in all conditions. Therefore, you shouldnever rely solely on any wireless phone for essentialcommunications (medical emergencies, for example).Remember, to make or receive any calls the phonemust be switched on and in a service area withadequate signal strength. Emergency calls may not bepossible on all wireless phone networks or whencertain network services and/or phone features are inuse. Check with local service providers.To make an emergency call, proceed as follows.1. If the phone is not on, switch it on.2. Key in the emergency number for your present location. Emergency numbers vary by location.3. Press the <SEND> key.If certain features are in use (call barring, for example),you may first need to deactivate those features beforeyou can make an emergency call. Consult thisdocument and your local cellular service provider.When making an emergency call, remember to give allthe necessary information as accurately as possible.Remember that your phone may be the only means ofcommunication at the scene of an accident; do not cutoff the call until given permission to do so.representative regarding your vehicle.You should also consult the manufacturer of anyequipment that has been added to your vehicle.Posted FacilitiesSwitch off your phone in any facility where postednotices require you to do so.Potentially Explosive AtmospheresSwitch off your phone when in any area with apotentially explosive atmosphere and obey all signsand instructions. Sparks in such areas could cause anexplosion or fire resulting in bodily injury or evendeath.Users are advised to switch off the phone while at arefueling point (service station). Users are remindedof the need to observe restrictions on the use ofradio equipment in fuel depots (fuel storage anddistribution areas), chemical plants or where blastingoperations are in progress.Areas with a potentially explosive atmosphere areoften but not always clearly marked. They includebelow deck on boats, chemical transfer or storagefacilities, vehicles using liquefied petroleum gas(such as propane or butane), areas where the aircontains chemicals or particles, such as grain, dustor metal powders, and any other area where youwould normally be advised to turn off your vehicleengine.safety-end-NorthA 1/27/03 2:05 PM Page 134

137HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn136HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonnCare and MaintenanceYour phone is a product of superior design andcraftsmanship and should be treated with care. Thesuggestions below will help you fulfill any warrantyobligations and allow you to enjoy this product formany years. • Keep the phone and all its parts and accessoriesout of the reach of small children’s.• Keep the phone dry. Precipitation, humidity andliquids contain minerals that will corrodeelectronic circuits.• Do not touch the phone with a wet hand while it ischarging. Doing so may cause an electric shock toyou or damage to the phone. • Do not use or store the phone in dusty, dirty areas,as its moving parts may be damaged.• Do not store the phone in hot areas. Hightemperatures can shorten the life of electronicdevices, damage batteries, and warp or meltcertain plastics.• Do not store the phone in cold areas. When thephone warms up to its normal operatingtemperature, moisture can form inside the phone,which may damage the phone’s electronic circuitboards.Other Important Safety Information• Only qualified personnel should service the phone orinstall the phone in a vehicle. Faulty installation orservice may be dangerous and may invalidate anywarranty applicable to the device.• Check regularly that all wireless phone equipment inyour vehicle is mounted and operating properly.• Do not store or carry flammable liquids, gases orexplosive materials in the same compartment as thephone, its parts or accessories.• For vehicles equipped with an air bag, rememberthat an air bag inflates with great force. Do notplace objects, including both installed or portablewireless equipment in the area over the air bag or inthe air bag deployment area. If wireless equipmentis improperly installed and the air bag inflates,serious injury could result.• Switch off your phone before boarding an aircraft.The use of wireless phones in aircraft may bedangerous to the operation of the aircraft, and isillegal.• Failure to observe these instructions may lead to thesuspension or denial of telephone services to theoffender, or legal action, or both.safety-end-NorthA 1/27/03 2:05 PM Page 136

139HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn138HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn• Do not drop, knock or shake the phone. Roughhandling can break internal circuit boards.• Do not use harsh chemicals, cleaning solvents orstrong detergents to clean the phone. Wipe it with asoft cloth slightly dampened in a mild soap-and-watersolution.• Do not paint it. Paint can clog the device’s movingparts and prevent proper operation.• Do not put the phone in or on heating devices, such asa microwave oven, a stove or a radiator. The phonemay explode when overheated.• Use only the supplied or an approved replacementantenna. Unauthorized antennas or modifiedaccessories may damage the phone and violateregulations governing radio devices.• If the phone, battery, charger or any accessory is notworking properly, take it to your nearest qualifiedservice facility. The personnel there will assist you,and if necessary, arrange for service.Acknowledging Special Precautions and the FCCand Industry Canada NoticeCautionsModifications not expressly approved by the partyresponsible for compliance could void the user's authorityto operate the equipment. FCC Compliance InformationThis device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received.Including interference that may cause undesiredoperation.Information to UserThis equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to part 15of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there isno guarantee that interference will not occur in aparticular installation. If this equipment does causeharmful interference to radio or television reception,which can be determined by turning the equipment off andon, the user is encouraged to try to correct theinterference by one or more of the following measures: safety-end-NorthA 1/27/03 2:05 PM Page 138

141AAppppeennddiixxAppendix A: CERTIFICATION INFORMATION (SAR)THIS MODEL PHONE MEETS THE GOVERNMENT’SREQUIREMENTS FOR EXPOSURE TO RADIO WAVES.Your wireless phone is a radio transmitter and receiver.It is designed and manufactured not to exceed theemission limits for exposure to radio frequency(RF)energy set by the Federal Communications Commissionof the U.S. Government. These limits are part ofcomprehensive guidelines and establish permittedlevels of RF energy for the general population. Theguidelines are based on safety standards that weredeveloped by independent scientific organizationsthrough periodic and thorough evaluation of scientificstudies. The standards include a substantial safetymargin designed to assure the safety of all persons,regardless of age and health. The exposure standard for wireless mobile phonesemploys a unit of measurement known as the SpecificAbsorption Rate(SAR). The SAR limit set by the FCC is1.6 W/kg. SAR Tests are conducted using standardoperating positions accepted by the FCC with thephone transmitting at its highest certified power levelin all tested frequency bands. Although the SAR isdetermined at the highest certified power level, theactual SAR level of the phone while operating can bewell below the maximum value. This is because thephone is designed to operate at multiple power levelsso as to use only the power required to reach thenetwork. In general, the closer you are to a wirelessbase station antenna, the lower the power output.140HHeeaalltthh aanndd SSaaffeettyy IInnffoorrmmaattiioonn• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/ TV technician for help.safety-end-NorthA 1/27/03 2:05 PM Page 140

143Appendix B: Guide to Safe and Responsible WirelessPhone UseCellular Telecommunications & Internet Association“Safety is the most important call you will ever make.”A Guide to Safe and Responsible Wireless Phone UseTENS OF MILLIONS OF PEOPLE IN THE U.S. TODAY TAKEADVANTAGE OF THE UNIQUE COMBINATION OFCONVENIENCE, SAFETY AND VALUE DELIVERED BY THEWIRELESS TELEPHONE. QUITE SIMPLY, THE WIRELESSPHONE GIVES PEOPLE THE POWERFUL ABILITY TOCOMMUNICATE BY VOICE-ALMOST ANYWHERE,ANYTIME-WITH THE BOSS, WITH A CLIENT, WITH THEKIDS, WITH EMERGENCY PERSONNEL OR EVEN WITHTHE POLICE. EACH YEAR, AMERICANS MAKE BILLIONSOF CALLS FROM THEIR WIRELESS PHONES, AND THENUMBERS ARE RAPIDLY GROWING. But an important responsibility accompanies thosebenefits, one that every wireless phone user mustuphold. When driving a car, driving is your firstresponsibility. A wireless phone can be an invaluabletool, but good judgment must be exercised at all timeswhile driving a motor vehicle-whether on the phone ornot. The basic lessons are ones we all learned as teenagers.Driving requires alertness, caution and courtesy. Itrequires a heavy dose of basic common sense-keep yourhead up, keep your eyes on the road, check your mirrorsfrequently and watch out for other drivers. It requiresobeying all traffic signs and signals and staying withinthe speed limit. It means using seatbelts and requiringother passengers to do the same. 142Before a new model phone is available for sale to thepublic, it must be tested and certified to the FCC that itdoes not exceed the limit established by the government-adopted requirement for safe exposure. The tests areperformed in positions and locations(e.g., at the ear andworn on the body) as required by the FCC for eachmodel. The highest SAR values for this model phone as reportedto the FCC are Head:0.334 W/Kg, Body-worn: 0.389 W/Kg.The FCC has granted an Equipment Authorization for thismodel phone with all reported SAR levels evaluated asin compliance with the FCC RF exposure guidelines. SARinformation on this model phone is on file with the FCCand can be found under the Display Grant section ofhttp://www.fcc.gov/oet/fccid after searching on FCC IDA3LSGHZ300.In the United States and Canada, the SAR limit formobile phones used by the public is 1.6watts/kilogram(W/kg) averaged over one gram of tissue.The standard incorporates a substantial margin of safetyto give additional protection for the public and toaccount for any variations in measurements. AAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 142

1454. Suspend conversations during hazardous drivingconditions or situations. Let the person you are speakingwith know you are driving; if necessary, suspend the callin heavy traffic or hazardous weather conditions. Rain,sleet, snow and ice can be hazardous, but so is heavytraffic. As a driver, your first responsibility is to payattention to the road. 5. Do not take notes or look up phone numbers whiledriving. If you are reading an address book or businesscard, or writing a “to do” list while driving a car, you arenot watching where you are going. It’s common sense.Don’t get caught in a dangerous situation because youare reading or writing and not paying attention to theroad or nearby vehicles. 6. Dial sensibly and assess the traffic; if possible, placecalls when you are not moving or before pulling intotraffic. Try to plan your calls before you begin your trip orattempt to coincide your calls with times you may bestopped at a stop sign, red light or otherwise stationary.But if you need to dial while driving, follow this simpletip-dial only a few numbers, check the road and yourmirrors, then continue. 7. Do not engage in stressful or emotional conversationsthat may be distracting. Stressful or emotionalconversations and driving do not mix-they are distractingand even dangerous when you are behind the wheel of acar. Make people you are talking with aware you aredriving and if necessary, suspend conversations whichhave the potential to divert your attention from the road. 144But with wireless phone use, driving safely means alittle more. This brochure is a call to wireless phoneusers everywhere to make safety their first priority whenbehind the wheel of a car. Wireless telecommunicationsis keeping us in touch, simplifying our lives, protecting usin emergencies and providing opportunities to helpothers in need. When it comes to the use of wirelessphones, safety is your most important call. Wireless Phone “Safety Tips” Below are safety tips to follow while driving and using awireless phone which should be easy to remember.1. Get to know your wireless phone and its features suchas speed dial and redial. Carefully read your instructionmanual and learn to take advantage of valuable featuresmost phones offer, including automatic redial andmemory. Also, work to memorize the phone keypad soyou can use the speed dial function without taking yourattention off the road. 2. When available, use a hands free device. A number ofhands free wireless phone accessories are readilyavailable today. Whether you choose an installedmounted device for your wireless phone or a speakerphone accessory, take advantage of these devices ifavailable to you. 3. Position your wireless phone within easy reach. Makesure you place your wireless phone within easy reachand where you can grab it without removing your eyesfrom the road. If you get an incoming call at aninconvenient time, if possible, let your voice mail answerit for you. AAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 144

1468. Use your wireless phone to call for help. Your wirelessphone is one of the greatest tools you can own toprotect yourself and your family in dangerous situations-with your phone at your side, help is only three numbersaway. Dial 9-1-1 or other local emergency number in thecase of fire, traffic accident, road hazard or medicalemergency. Remember, it is a free call on your wirelessphone! 9. Use your wireless phone to help others inemergencies. Your wireless phone provides you a perfectopportunity to be a “Good Samaritan” in your community.If you see an auto accident, crime in progress or otherserious emergency where lives are in danger, call 9-1-1or other local emergency number, as you would wantothers to do for you. 10. Call roadside assistance or a special wireless non-emergency assistance number when necessary. Certainsituations you encounter while driving may requireattention, but are not urgent enough to merit a call foremergency services. But you still can use your wirelessphone to lend a hand. If you see a broken-down vehicleposing no serious hazard, a broken traffic signal, a minortraffic accident where no one appears injured or avehicle you know to be stolen, call roadside assistanceor other special non-emergency wireless number.Careless, distracted individuals and people drivingirresponsibly represent a hazard to everyone on the road.Since 1984, the Cellular Telecommunications IndustryAssociation and the wireless industry have conductededucational outreach to inform wireless phone users of147their responsibilities as safe drivers and good citizens.As we approach a new century, more and more of us willtake advantage of the benefits of wireless telephones.And, as we take to the roads, we all have aresponsibility to drive safely.“The wireless industry reminds you to use your phonesafely when driving.”Cellular Telecommunications & Internet AssociationFor more information, please call 1-888-901-SAFE. For updates: http://www.wow-com.com/consumer/issues/driving/articles.cfm?ID=85AAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 146

149low level RF that does not produce heating effectscauses no known adverse health effects. Many studiesof low level RF exposures have not found any biologicaleffects. Some studies have suggested that somebiological effects may occur, but such findings have notbeen confirmed by additional research. In some cases,other researchers have had difficulty in reproducingthose studies, or in determining the reasons forinconsistent results.3. What is FDA’s role concerning the safety of wirelessphones?Under the law, FDA does not review the safety ofradiation-emitting consumer products such as wirelessphones before they can be sold, as it does with newdrugs or medical devices. However, the agency hasauthority to take action if wireless phones are shown toemit radiofrequency energy (RF) at a level that ishazardous to the user. In such a case, FDA could requirethe manufacturers of wireless phones to notify users ofthe health hazard and to repair, replace or recall thephones so that the hazard no longer exists.Although the existing scientific data do not justify FDAregulatory actions, FDA has urged the wireless phoneindustry to take a number of steps, including thefollowing:Support needed research into possible biological effectsof RF of the type emitted by wireless phones; Design wireless phones in a way that minimizes any RFexposure to the user that is not necessary for devicefunction; and Cooperate in providing users of wireless phones with the148Appendix C: Consumer Update on Wireless PhonesU.S. Food and Drug Administration1. What kinds of phones are the subject of this update?The term wireless phone refers here to hand-heldwireless phones with built-in antennas, often called cell,mobile, or PCS phones. These types of wireless phonescan expose the user to measurable radiofrequencyenergy (RF) because of the short distance between thephone and the user s head. These RF exposures arelimited by Federal Communications Commission safetyguidelines that were developed with the advice of FDAand other federal health and safety agencies. When thephone is located at greater distances from the user, theexposure to RF is drastically lower because a person’s RFexposure decreases rapidly with increasing distancefrom the source. The so-called “cordless phones,” whichhave a base unit connected to the telephone wiring in ahouse, typically operate at far lower power levels, andthus produce RF exposures well within the FCC’scompliance limits.2. Do wireless phones pose a health hazard?The available scientific evidence does not show that anyhealth problems are associated with using wirelessphones. There is no proof, however, that wireless phonesare absolutely safe. Wireless phones emit low levels ofradiofrequency energy (RF) in the microwave range whilebeing used. They also emit very low levels of RF when inthe stand-by mode. Whereas high levels of RF canproduce health effects (by heating tissue), exposure toAAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 148

1514. What is FDA doing to find out more about the possiblehealth effects of wireless phone RF?FDA is working with the U.S. National ToxicologyProgram and with groups of investigators around theworld to ensure that high priority animal studies areconducted to address important questions about theeffects of exposure to radiofrequency energy (RF).FDA has been a leading participant in the World HealthOrganization International Electromagnetic Fields (EMF)Project since its inception in 1996. An influential resultof this work has been the development of a detailedagenda of research needs that has driven theestablishment of new research programs around theworld. The Project has also helped develop a series ofpublic information documents on EMF issues.FDA and the Cellular Telecommunications & InternetAssociation (CTIA) have a formal Cooperative Researchand Development Agreement (CRADA) to do research onwireless phone safety. FDA provides the scientificoversight, obtaining input from experts in government,industry, and academic organizations. CTIA-fundedresearch is conducted through contracts to independentinvestigators. The initial research will include bothlaboratory studies and studies of wireless phone users.The CRADA will also include a broad assessment ofadditional research needs in the context of the latestresearch developments around the world.5. What steps can I take to reduce my exposure toradiofrequency energy from my wireless phone?150best possible information on possible effects of wirelessphone use on human health FDA belongs to an interagency working group of thefederal agencies that have responsibility for differentaspects of RF safety to ensure coordinated efforts at thefederal level. The following agencies belong to thisworking group:National Institute for Occupational Safety and Health Environmental Protection Agency Federal Communications Commission Occupational Safety and Health Administration National Telecommunications and InformationAdministration The National Institutes of Health participates in someinteragency working group activities, as well.FDA shares regulatory responsibilities for wirelessphones with the Federal Communications Commission(FCC). All phones that are sold in the United States mustcomply with FCC safety guidelines that limit RF exposure.FCC relies on FDA and other health agencies for safetyquestions about wireless phones.FCC also regulates the base stations that the wirelessphone networks rely upon. While these base stationsoperate at higher power than do the wireless phonesthemselves, the RF exposures that people get from thesebase stations are typically thousands of times lower thanthose they can get from wireless phones. Base stationsare thus not the primary subject of the safety questionsdiscussed in this document.AAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 150

153Some groups sponsored by other national governmentshave advised that children be discouraged from usingwireless phones at all. For example, the government inthe United Kingdom distributed leaflets containing sucha recommendation in December 2000. They noted that noevidence exists that using a wireless phone causes braintumors or other ill effects. Their recommendation to limitwireless phone use by children was strictlyprecautionary; it was not based on scientific evidencethat any health hazard exists.7. Do hands-free kits for wireless phones reduce risksfrom exposure to RF emissions?Since there are no known risks from exposure to RFemissions from wireless phones, there is no reason tobelieve that hands-free kits reduce risks. Hands-free kitscan be used with wireless phones for convenience andcomfort. These systems reduce the absorption of RFenergy in the head because the phone, which is thesource of the RF emissions, will not be placed againstthe head. On the other hand, if the phone is mountedagainst the waist or other part of the body during use,then that part of the body will absorb more RF energy.Wireless phones marketed in the U.S. are required tomeet safety requirements regardless of whether they areused against the head or against the body. Eitherconfiguration should result in compliance with the safetylimit.8. Do wireless phone accessories that claim to shield thehead from RF radiation work?152If there is a risk from these products—and at this pointwe do not know that there is—it is probably very small.But if you are concerned about avoiding even potentialrisks, you can take a few simple steps to minimize yourexposure to radiofrequency energy (RF). Since time is akey factor in how much exposure a person receives,reducing the amount of time spent using a wirelessphone will reduce RF exposure.If you must conduct extended conversations by wirelessphone every day, you could place more distance betweenyour body and the source of the RF, since the exposurelevel drops off dramatically with distance. For example,you could use a headset and carry the wireless phoneaway from your body or use a wireless phone connectedto a remote antenna Again, the scientific data do not demonstrate thatwireless phones are harmful. But if you are concernedabout the RF exposure from these products, you can usemeasures like those described above to reduce your RFexposure from wireless phone use.6. What about children using wireless phones?The scientific evidence does not show a danger to usersof wireless phones, including children and teenagers. Ifyou want to take steps to lower exposure toradiofrequency energy (RF), the measures describedabove would apply to children and teenagers usingwireless phones. Reducing the time of wireless phoneuse and increasing the distance between the user andthe RF source will reduce RF exposure.AAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 152

155FDA has tested hearing aids for interference fromhandheld wireless phones and helped develop avoluntary standard sponsored by the Institute ofElectrical and Electronic Engineers (IEEE). This standardspecifies test methods and performance requirements forhearing aids and wireless phones so that that nointerference occurs when a person uses a compatiblephone and a compatible hearing aid at the same time.This standard was approved by the IEEE in 2000.FDA continues to monitor the use of wireless phones forpossible interactions with other medical devices. Shouldharmful interference be found to occur, FDA will conducttesting to assess the interference and work to resolvethe problem.10. What are the results of the research done already?The research done thus far has produced conflictingresults, and many studies have suffered from flaws intheir research methods. Animal experimentsinvestigating the effects of radiofrequency energy (RF)exposures characteristic of wireless phones have yieldedconflicting results that often cannot be repeated in otherlaboratories. A few animal studies, however, havesuggested that low levels of RF could accelerate thedevelopment of cancer in laboratory animals. However,many of the studies that showed increased tumordevelopment used animals that had been geneticallyengineered or treated with cancer-causing chemicals soas to be pre-disposed to develop cancer in the absenceof RF exposure. Other studies exposed the animals to RFfor up to 22 hours per day. These conditions are notsimilar to the conditions under which people usewireless phones, so we don t know with certainty what154Since there are no known risks from exposure to RFemissions from wireless phones, there is no reason tobelieve that accessories that claim to shield the headfrom those emissions reduce risks. Some products thatclaim to shield the user from RF absorption use specialphone cases, while others involve nothing more than ametallic accessory attached to the phone. Studies haveshown that these products generally do not work asadvertised. Unlike “hand-free” kits, these so-called“shields” may interfere with proper operation of thephone. The phone may be forced to boost its power tocompensate, leading to an increase in RF absorption. InFebruary 2002, the Federal trade Commission (FTC)charged two companies that sold devices that claimed toprotect wireless phone users from radiation with makingfalse and unsubstantiated claims. According to FTC,these defendants lacked a reasonable basis tosubstantiate their claim.9. What about wireless phone interference with medicalequipment?Radiofrequency energy (RF) from wireless phones caninteract with some electronic devices. For this reason,FDA helped develop a detailed test method to measureelectromagnetic interference (EMI) of implanted cardiacpacemakers and defibrillators from wireless telephones.This test method is now part of a standard sponsored bythe Association for the Advancement of Medicalinstrumentation (AAMI). The final draft, a joint effort byFDA, medical device manufacturers, and many othergroups, was completed in late 2000. This standard willallow manufacturers to ensure that cardiac pacemakersand defibrillators are safe from wireless phone EMI.AAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 154

157156the results of such studies mean for human health.Three large epidemiology studies have been publishedsince December 2000. Between them, the studiesinvestigated any possible association between the use ofwireless phones and primary brain cancer, glioma,meningioma, or acoustic neuroma, tumors of the brain orsalivary gland, leukemia, or other cancers. None of thestudies demonstrated the existence of any harmfulhealth effects from wireless phone RF exposures.However, none of the studies can answer questionsabout long-term exposures, since the average period ofphone use in these studies was around three years.11. What research is needed to decide whether RFexposure from wireless phones poses a health risk?A combination of laboratory studies and epidemiologicalstudies of people actually using wireless phones wouldprovide some of the data that are needed. Lifetimeanimal exposure studies could be completed in a fewyears. However, very large numbers of animals would beneeded to provide reliable proof of a cancer promotingeffect if one exists. Epidemiological studies can providedata that is directly applicable to human populations, but10 or more years follow-up may be needed to provideanswers about some health effects, such as cancer. Thisis because the interval between the time of exposure toa cancer-causing agent and the time tumors develop - ifthey do - may be many, many years. The interpretation ofepidemiological studies is hampered by difficulties inmeasuring actual RF exposure during day-to-day use ofwireless phones. Many factors affect this measurement,such as the angle at which the phone is held, or whichmodel of phone is used.12. Which other federal agencies have responsibilitiesrelated to potential RF health effects?Additional information on the safety of RF exposures fromvarious sources can be obtained from the followingorganizations.FCC RF Safety Program: http://www.fcc.gov/oet/rfsafety/Environmental Protection Agency (EPA): http://www.epa.gov/radiation/ Occupational Safety and Health Administration’s (OSHA): http://www.osha-slc.gov/SLTC/radiofrequencyradiation/index.htmlNational Institute for Occupational Safety and Health(NIOSH): http://www.cdc.gov/niosh/emfpg.htmlWorld health Organization (WHO): http://www.who.int/peh-emf/ International Commission on Non-Ionizing RadiationProtection: http://www.icnirp.deNational Radiation Protection Board (UK): http://www.nrpb.org.uk Updated 4/3/2002: US Food and Drug Administrationhttp://www.fda.gov/cellphonesAAppppeennddiixxAAppppeennddiixxsafety-end-NorthA 1/27/03 2:05 PM Page 156

82IndexAABC mode, text input • 23Alarm • 53Answeringcall • 24, 27second call • 25Anykey answer • 64Auto redial • 67BBacklight time, set • 65Barring, calls • 66Batterycharging • 7low indicator • 8precautions • 76Bluetoothreceiving, data • 69sending, data • 69settings • 68Broadcast messages • 45Browser, WAP • 49CCalculator • 58Call costs • 37Call recordsdialled • 37missed • 36received • 37Call time • 38Caller group • 51Caller ID • 65Calls answering • 24, 27barring • 66diverting • 66holding • 25redialling • 24rejecting • 24waiting • 67Cameraphotos • 60videos • 62Characters, enter • 22Conference call • 27Configuration messages • 40Connect tone • 30Contactscopying • 52editing • 50options • 50setting • 53speed-dialling • 52Conversion • 59Creating messagese-mail • 40MMS with attachments • 39MMS • 39SMS • 38Creating organiseranniversaries • 55events • 54memos • 55tasks • 55DDeletingcontacts • 50e-mails • 44events • 56MMS messages • 42photos • 32, 62SMS messages • 42video clips • 63Delivery reports, message • 45Dialled calls • 37Displaybrightness • 65language • 64settings • 65Diverting, calls • 66DTMF tones, send • 26EE-mailscreating/sending • 40deleting • 44settings • 47viewing • 43Emergency calls • 79FFDN (Fixed Dial Number) mode • 72File messager • 39Folder tone • 30Forwardinge-mails • 44MMS messages • 42GGames • 33Greeting message • 65HHealth and safety • 76Holding, call • 25IIcons, description • 10Images, downloaded • 31Inbox, messagese-mail • 43MMS • 40SMS • 41web • 42Infrared, connect • 69

83Index International calls • 24Internet • 49Kkey tone volume • 30Keypad tonesselecting • 30sending • 26LLanguage, select • 64Last number, redial • 24LCD brightness • 65Lockingmedia contents • 72phone • 72SIM card • 72Loudspeaker • 25Low battery indicator • 8MMemory card • 20Memory statuscontacts • 53messages • 48phone • 73scheduled events • 59Message tone • 30MessagesCB • 45greeting • 65MMS with attachments • 39MMS • 39SMS • 38web • 42Minute minder • 30Missed alarm events • 54Missed calls • 36MMS messagescreating/sending • 39deleting • 42settings • 46viewing • 42Multi-party calls • 27Music, downloaded • 35Mutingkey tones • 26microphone • 26NName card • 52Namesentering • 22searching • 50Network selection • 70OOrganiser • 53Outbox, messages • 43Own number • 53PPasswordbarring • 66phone • 72Phonecare and maintenance • 80display • 10icons • 10locking • 72password • 72resetting • 73switching on/off • 8unpacking • 6Photosdeleting • 32, 62editing • 31taking • 60viewing • 31PIN, change • 73PIN2, change • 73Power on/off tone • 30Privacy • 72Problems, solve • 74Profiles • 30RReceived calls • 37Received messagese-mail • 43MMS • 42SMS • 41web • 42Recordingvidoes • 62voice memos • 57Rediallingautomatically • 67manually • 24Resetting phone • 73Road safety • 77Roaming • 70SSafetyinformation • 76precautions • 1Sent messages • 43Side key, set • 64SIM cardinserting • 7locking • 72SMS messagescreating/sending • 38deleting • 41settings • 45viewing • 41Sound setting • 30Sounds, downloaded • 33

84IndexSpeed-dial • 52Switching on/offmicrophone • 26phone • 8speaker • 25TTemplatesMMS • 44text • 44Text input mode, change • 22Text, enter • 22Tone connect • 30folder • 30keypad • 30message • 30minute minder • 30power on/off • 30VVideo callsmaking • 27setting • 67Video clipsplaying • 34recording • 62Voice mail server • 48Voice memosdeleting • 58playing • 57recording • 57WWaiting call • 67Wallpaperexternal display • 65main display • 65WAP browser • 49World time • 58

Declaration of Conformity (R&TTE) For the following product:GSM900/GSM1800/WCDMAPortable Cellular Telephone (Product Name)SGH-Z300T(Model Number)Manufactured at:Samsung Electronics Co., Ltd, 94-1 Imsu-Dong, Gumi City, Kyung Buk, Korea, 730-350(factory name, address*)to which this declaration relates, is in conformity with the following standards and/or other normative documents.SafetyEMC SAR NetworkWe hereby declare the [all essential radio test suites have been carried out and that] the above named product is in conformity to all the essential requirements of Directive 1999/5/EC.The conformity assessment procedure referred to in Article 10 and detailed in Annex[IV] of Directive 1999/5/EC has been followed with the involvement of the following Notified Body(ies):BABT, Claremont House, 34 Molesey Road, Walton-on-Thames, KT12 4RQ, UK Identification mark: 168The technical documentation kept at:Samsung Electronics Euro QA Lab.which will be made available upon request.(Representative in the EU)Samsung Electronics Euro QA Lab.Blackbushe Business Park, Saxony Way, Yateley, Hampshire, GU46 6GG, UK(place and date of issue) (name and signature of authorised person)* This is not the address of the Samsung Service Centre. For the address or the phone number of the Samsung Service Centre, see the warranty card or contact the retailer where you purchased your phone.