Samsung Electronics Co SSAR1000 RFID Reader User Manual R1000 ENG 1007 indd

Samsung Electronics Co Ltd RFID Reader R1000 ENG 1007 indd

User manual

RFID Readeruser manualSSA-R1000SSA-R1100imagine the possibilitiesThank you for purchasing this Samsung product.To receive more complete service, please visit our website.www.samsungsecurity.com
2_ Safety informationsafety informationCAUTIONRISK OF ELECTRIC SHOCK.DO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.WARNINGTo reduce the risk of fi re or electric shock, do not expose this appliance to rain or moisture.WARNINGBe sure to use only the standard adapter that is specifi ed in the specifi cation sheet.Using any other adapter could cause fi re, electrical shock, or damage to the product.Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or damage to the product.Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fi re.Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.When installing the controller, fasten it securely and fi rmly. The fall of controller may cause personal injury.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers fi lled with water on top of the controller. Doing so may cause personal injury due to fi re, electric shock, or falling objects.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.). When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.CAUTIONDo not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference.Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fi re or electric shock.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fi re or damage to the product.•1.2.3.4.5.6.7.8.9.10.1.2.3.4.
EnglisEnglish _ 3SAFETY INFORMATIONKeep out of direct sunlight and heat radiation sources. It may cause fi re.Install it in a place with good ventilation.Avoid aiming the controller directly towards extremely bright objects such as sun.Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.The Mains plug is used as a disconnect device and shall stay readily operable at any time.FCC StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :This device may not cause harmful interference, andThis device must accept any interference received including interference that may cause undesired operation.5.6.7.8.9.1)2)Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specifi ed by the manufacturer. Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.1.2.3.4.5.6.7.8.9.10.11.12.13.14.IMPORTANT SAFETY INSTRUCTIONSCautionThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in ac-cordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
4_ ContentscontentsPRODUCT INTRODUCTION55 Features5 What’s included6 At a Glance7 Cable Color Scheme7 Cable SelectionINSTALLATION AND EXTERNAL CONNECTION88 Installation9 Precautions on installation10 External ConnectionINITIALIZATION1111 Basic OperationsOUTPUT FORMAT1212 WIEGAND OutputTROUBLESHOOTING1313 TroubleshootingPRODUCT SPECIFICATIONS1414 Product Specifi cations
EnglisEnglish _ 5PRODUCT INTRODUCTIONFEATURESThis product is an elegant-looking proximity reader which has the maximum read range of 10cm (4”), can be easily installed on a metal doorframe or the wall. Basically, both R1000 and R1100 use the same module with epoxy molding, which guarantees operation in any weather and environment condition. The two different bezels of two models are compatible with each other, meaning one can be replaced with the other according to the wall condition or the applicable situation. Green and red LED indicators and the Piezo buzzer ensure reliable and accurate operations.125KHz Proximity Reader PSK Modulation 26 bit WiegandControl of External LED IndicatorsControl of External BuzzerReverse Polarity ProtectionWeatherproofWHAT’S INCLUDEDCheck if the following items are included in the product package.What’s included in SSA-R1000xGnBezel of SSA-R1000 READER Module3.5 x 40 screws (x2)3.5 x 25 screws (x2)6 x 30 Plastic Anchors(x2)Quick Guide CD ManualWhat’s included in SSA-R1100xGnBezel of SSA-R1100 READER Module3.5 x 40 screws (x2)3.5 x 25 screws (x2)6 x 30 Plastic Anchors(x2)Quick Guide CD Manual◆◆◆◆◆◆◆product introduction
6_ Product Introductionproduct introductionAT A GLANCEFront/RearLED Displays the system operation status using red and green indicators.Buzzer Piezo buzzer.Connection Cable Used to connect to the power or I/O cable.Fixing Hole Fixing hole for wall-mounting.243
EnglisEnglish _ 7PRODUCT INTRODUCTIONCABLE COLOR SCHEMEItem Cable Color Signal Line DescriptionPowerRed DC +12V DC +12V suppliedBlack GND Earth-grounding for powerInputBlue Buzzer ControlBUZZER Control Input PortYellow LED Control LED Control Input PortOutputGreen Out Wiegand 0 Wiegand Data 0 Output PortWhite Out Wiegand 1 Wiegand Data 1 Output PortNot usedOrange NC Not ConnectedCABLE SELECTIONItemCable TypeCable TypeMaximum Allowable DistanceMaximum Allowable Distance1Power (DC12V)Belden #9409, 18 AWG 2 Conductor, Unshielded Belden #9409, 18 AWG 2 Conductor, Unshielded Within 3mWithin 3m2WIEGAND OutputBuzzer ControlLED ControlBelden #9512, 22 AWG 4 Conductor, Shielded Belden #9514, 22 AWG 8 Conductor, Shielded
8_ Installation and External Connectioninstallation and external connectionINSTALLATION- Inserted in the doorframe / attached to the wallTwo 6-32 or M3 holes are 3.3” (8.38 cm) away from each other vertically; between the two exists one 1/2” hole through which the reader cables are arranged. The midway hole is located 1.7” (4.31cm) down from the upper hole.(If the product is already installed, you can skip this step.)Insert the reader cables to the midway hole and fi x the reader module with two 6-32 or M3 screws.Insert the reader module into the bezel and push it up until you hear a click.1.2.3.Electric Gang Box MountWall MountMullion MountLowerReaderModuleBezel6-32 hole3.3”(8.38cm)Upper6-32 hole1/2”hole1.7”(4.31cm)6-32 or M3 Screws 6-32 or M3 ScrewsReaderModuleBezelGang Box
EnglisEnglish _ 9INSTALLATION AND EXTERNAL CONNECTIONPRECAUTIONS ON INSTALLATIONIf installing on a metal wallIf you install the reader on a metal wall, the read range may be reduced.To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below.If installing more than one reader side by side or front and backIf you install more than one reader side by side or front and back, the read range may be reduced. In this case, if you present a card to one reader, the other reader may recognize the same card, meaning both readers read the same card simultaneously.To avoid this problem, keep at least 20 cm of space between the two readers.BACK TO BACKINSTALLATIONSIDE BY SIDEINSTALLATION<Front and Back><Side by Side>Metal WallSpacerReader#Reader 2#Reader 1Minimum 20cm#Reader 1#Reader 2Minimum 20cm
10_ Installation and External Connectioninstallation and external connectionEXTERNAL CONNECTIONWiring DiagramItem Cable ColorPower Supply UnitConnect the DC+12V to the red line.Connect GND to the black line.Wiegand ConnectionConnect the green line of the product to the Wiegand D0 input port of the controller.Connect the white line of the product to the Wiegand D1 input port of the controller.LED Control To control the LED indicators, connect the yellow line to the output port (relay) of the controller.Buzzer Control To control the built-in buzzer, connect the blue line to the output port (relay) of the controller.BlueYellowRed BlackBuzzer Control InLED Control InDC +12V GNDSSA-R1000/SSA-R1100Wiegand Data 0 OutWiegand Data 1 OutGreenWhitePCCONTROLLERPOWER
EnglisEnglish _ 11INITIALIZATIONinitializationBASIC OPERATIONSInitial State (when the power is supplied)When you apply power to the reader, it will sound a beep before entering Standby with the red indicator turned on .Using the cardPresent the card to the reader until you hear a beep and the red indicator turns green. When the reader has transferred the card data to the controller, it returns to Standby with the red indicator turned on and waits for reading the next card.LED ControlYou can control the LED indicator of the device at your preference.Connect the LED control input line (yellow) to the NO port of the controller relay output, and GND to the COM port.Set the I/O of the controller so that you can change the color of the LED indicators. While the LED control is working, the green indicator stays solid.This function not only enables you to change the color representing Standby from red to green, but it can be also applied to make various modifi cations according to the different I/O settings of the controller.For more information about the I/O settings of the controller, refer to the user manual of the controller.Buzzer ControlYou can control the buzzer of the device at your preference.You can confi gure the I/O settings of the controller so that it sounds a beep. While the buzzer control is working, the product keeps sounding the beep.The controller can use the I/O settings to set the buzzer control so that it sounds an additional beep for authorized or unauthorized access upon user authentication.Furthermore, you can make various modifi cations according to the different I/O settings of the controller.For more information about the I/O settings of the controller, refer to the user manual of the controller.Card reading is not available while the buzzer control is sounding the buzzer.JCardXYZ[\]^_`lzj lzjWizzhTzYWWW
12_ Output Formatoutput formatWIEGAND OUTPUTTiming DiagramData TypeBit 1 : Even Parity (bit 2 ~ bit 13)Bit 2 ~ 9 : Facility Code (000 ~ 255) Bit 10 ~ 25 : ID Number (00000 ~ 65,535) Bit 26 : Odd Parity (bit 14 ~ bit 25) ••••100us1msDATA-0DATA-11235V0V0V5V0LOGIC 1 1 1 0 0n-2 n-1 n *n : 26
EnglisEnglish _ 13TROUBLESHOOTINGtroubleshootingTROUBLESHOOTINGIf the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact the SAMSUNG Customer Service near you.PROBLEM SOLUTIONMy card is not read properly. 1) Check the rated voltage specifi ed in the user manual and the catalog.2) Ensure that the card must comply with the PSK (125 KHz Proximity ) format provided by Samsung.Cards of 125 kHz purchased from other manufacturers may not be supported.3) If the problem persists, contact the nearest customer service for your assistance.When I turn on the product, it sounds a beep with dimly turned on indicator.1) Ensure that you are using a larger-capacity adaptor than specifi ed in the user manual or the catalog, which should cover the rated current consumption of the reader. If you are using multiple readers that are connected to one adaptor, make sure that the adaptor should be large enough to cover the current consumption multiplied by the reader count.2) Even with a large adaptor enough to supply adequate power, if the power cable is not a dedicated line (such as communication line or UPT cable), or if it’s so long to cause power loss, you’d better replace it with a dedicated line or reinforce it.3) If the problem persists, contact the nearest customer service for your assistance.
14_ product specifi cationsproduct specifi cationsPRODUCT SPECIFICATIONSItem SSA-R1000 SSA-R1100Power / Current DC 12V / Max.120mA Reading Time (Card) 30msInput Port 2ea : External LED Control, External Buzzer ControlOutput Port 26bit WiegandLED Indicator 2 Color LED (Red and Green) Beeper Piezo Buzzer Operating Temperature -30°C to +50°COperating Humidity 10% to 90% relative humidity non-condensing Color / Material Silver with Black/ Polycarbonate Dimension (W x H x D(mm))47.0 x 122.0 x 26.0 75.3 x 122.0 x 26.0Weight 130g 150gRF Specifi cationsFrequency : 125KHzModulation : PSKNo. of Channels : 1CHOutput : Less than 65.80dBuA/m at a distance of 10m
Correct disposal of batteries in this product(Applicable in the European Union and other European countries with separate battery return systems.)This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.Correct Disposal of This Product (Waste Electrical & Electronic Equipment)(Applicable in the European Union and other European countries with separate collection systems)This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Navigation menu