Samsung Electronics Co SW216 CD - R/W Drive User Manual 01 SW 216 eng

Download:
Mirror Download [FCC.gov]
Document ID	153298
Application ID	rrusEHMgJ69mJ5qck+1seQ==
Document Description	Samsung Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.21kB (152583 bits)
Date Submitted	2001-06-05 00:00:00
Date Available	2001-06-05 00:00:00
Creation Date	2001-04-18 09:20:18
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2001-04-18 09:20:28
Document Title	01.SW-216-eng
Document Creator	QuarkXPress E: LaserWriter 8 8.5.1
Document Author:	ckm

CD-R/RW DRIVE
SW-216
User's Guide
FCC Compliance
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Safety Precautions
Contents
The following diagrams illustrate the precautions to be taken when using
your CD-R/RW drive.
You must not use the drive in any manner other than that specified in this guide.
CAUTION
Do not attempt to repair the CD-R/RW drive yourself. Contact
your dealer or local SAMSUNG representative for all repairs.
If you make any adjustments or perform any operations other
than those specified in this guide, you run the risk of exposure to
hazardous radiation.
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Your CD-R/RW Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Upgrading the Firmware Flash Memory . . . . . . . . . . . . . . . . . . . . . . . . .5
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installing the CD-R/RW Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installing the CD Record Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Installing the Device Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Setting Up the Device Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Using the CD-R/RW Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Storing and Cleaning Your Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Solving Recording Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Recommended Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Solving Technical Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Avoid exposing your eyes or skin to direct or scattered radiation.
WARRANTY Please refer to the Samsung limited warranty statements.
Precautions
1. To reduce the risk of fire or electric shock, do not expose
this appliance to rain or moisture.
2. Always check each disc for cracks before using it. If there are
cracks on the surfaces, especially around the border of the
center hole, we recommend that you make a copy of the disc
immediately and then stop using it. If you continue using the
disc, it will probably develop more cracks and eventually cause
irreparable damage.
3. Do not use poor quality discs:
● From unknown sources
● Without any copyright
● Scratched or damaged in any way
* All product names mentioned in this document are trademarks or registered trademarks
of their respective owners.
Your CD-R/RW Drive
Upgrading the Firmware Flash Memory
The product firmware can be upgraded by downloading the updated file from the
following Web site:
http://www.samsungelectronics.com
System Requirements
Before you install the CD-R/RW drive, we strongly recommend that you
check that your setup meets the system requirements listed below.
1.
2.
3.
4.
Connector for stereo headphones with a 3.6 mm stereo mini-jack
Headphone volume control
Indicator light (when it is green, a disc is being read or recorded)
Disc compartment (the compartment opens and closes
automatically when you press the Eject button)
5. Emergency eject hole (if the compartment does not open when
you press the Eject button, power off the computer, insert a pin or
unfolded paper clip in the hole and push firmly)
6. Eject button
Item
Description
Computer
Intel Pentium II (or higher), 32 MB of RAM (or higher)
with an IDE interface
Disk space
700 MB minimum
Windows version
Windows 95 / 98 OSR2 / 2000 / ME or Windows NT 4.0
(or higher)
D M A
Important!
Please read the entire DMA installation guide before installing your CD-R/RW drive.
About DMA Installation
For stable writing performance at high speeds, Installation of DMA transfer mode for
IDE/ATAPI interface is strongly recommended. Especially for writing at 12x speed,
DMA installation should be set to enabled on your PC system instead of PIO transfer
mode. If DMA is not set to enabled on your PC, the data transfer may become too
slow and resulting in data writing errors.
DMA Setting
1. Two-pin digital audio output terminal for use with a sound or
MPEG card supporting digital audio features
2. Four-pin sound output terminal for use with a sound card (refer to
the sound card documentation for further details)
3. Master/slave select terminal
4. Forty-pin host IDE interface connector
5. Four-pin power terminal
Before you install your CD-R/RW drive, we recommend to set DMA to enabled on
your PC system. See the following procedure to set DMA transfer mode in windows
oprerating system. (Windows 95 OSR2/98/ME)
Click on START
Click on Settings
● Select Control Panel
● Select the System Icon
● Select the Device Manager panel
in System Properties
● Expand the CD-ROM icon
Select your CD-R/RW drive
Click on the Properties button
● Click on the Settings tab
● Check the DMA checkbox to enables DMA.
● Click OK
● Restart your PC
●
●
●
●
Installing the CD-R/RW Drive
To install your CD-R/RW drive in the PC, proceed as follows.
1 Make sure that the PC is powered off and disconnected from any power source.
2 If necessary, attach a horizontal bracket to both sides of
the drive.
●
Use of the brackets depends on your computer
model; you can purchase these accessories
separately from your computer dealer.
2 Installing a jumper on the master/slave select terminal
Install the jumper in the correct position on the terminal:
MA to use the device in the master mode
SL to use the device in the slave mode
CS to control the device via a CSEL
host interface signal
See Step 3 for further details.
3 Remove the cover from a free expansion slot and install
the CD-R/RW drive, as shown in the illustration.
3 Connecting the IDE cable
Two configurations are possible.
●
●
The CD-R/RW drive is the only IDE device in addition to the hard disk.
If you have no free expansion slot, install the drive in
place of the diskette drive.
CD-R/RW drive
IDE port
Mother board
CD-R/RW Hard disk
(MA)
(SL)
Install the jumper in the SL position (Slave).
Connect the 40-pin flat IDE cable from the IDE port on the mother board, first to
the CD-R/RW drive and then to the hard disk.
Connecting the Cables
●
You already have an additional IDE device installed in your computer.
Second IDE cable
First IDE cable
1. Power cable
2. Master/slave select terminal
3. IDE cable
4. Audio cable
1 Connecting the power cable
The 4-pin power cable from the internal power unit of your computer must be
connected to the power terminal on the rear of the CD-R/RW drive.
Mother
board
CD-R/RW CD-ROM
(MA)
(SL)
Hard disk
(SL)
Hard disk
(MA)
Install the jumper in the MA position (Master).
Connect the 40-pin flat IDE cable from a second IDE port on the mother
board directly to the CD-R/RW drive or first to another additional IDE drive
and then to the CD-R/RW drive.
4 Connecting the audio cable from a sound card
Connect the 4-pin audio cable between the sound output terminal on the CD-R/RW
drive and the audio input terminal on the sound card.
Installing the CD Record Utility
To record data on a CD-R or CD-RW disc in the CD-R/RW drive, you must first
install the CD record utility. For compatibility reasons, you are recommended to
uninstall any existing software of the same type before installing this utility.
1 Insert the disc supplied with the CD-R/RW drive in the drive.
2 Follow the instructions displayed on the screen to install the utility. Refer to
the separate utility documentation for further details.
3 Store the utility disc in a safe place.
Setting Up the Device Driver
◆
Automatic Setup
1 Insert the setup diskette in the diskette drive and change the directory to A:,
where A: is the diskette drive.
To do so, type A: after the C:\ prompt and press [Enter].
2 Type CDSETUP and press [Enter].
3 Reboot the computer.
Installing the Device Driver
No additional device driver is needed for Windows 95/98/2000/ME/NT4.0,
as the default Windows device driver is used. You can check that the CD-R/RW
drive has been correctly detected by Windows. To do so, proceed as follows.
1 Double-click on the My Computer icon on your desktop.
2 Double-click on the Control Panel folder.
◆
Manual Setup
1 Make the C:\SAMSUNG directory.
2 Copy the files from the diskette to the C:\SAMSUNG directory.
To do so, type COPY A:*.* C:\SAMSUNG after the C:\ prompt and press
[Enter].
3 Edit the CONFIG.SYS file.
Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.
3 Double-click on the System icon.
LAST DRIVE = Z
----------------------------------------------------------------------DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V
4 Click on the Device Manager tab.
5 Expand the CD-ROM branch.
The SAMSUNG CD-R/RW SW - *** device name is displayed.
4 Edit the AUTOEXEC.BAT file.
Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.
The SAMSUNG device driver enables discs in the CD-R/RW drive to be read but not
recorded in an MS-DOS environment; the driver is located in the D driver folder on
the CD record utility disc.
----------------------------------------------------------------------C :\SAMSUNG\MSCDEX /D:SSCD000
5 Reboot the computer.
Using the CD-R/RW Drive
To play audio or video CDs in your CD-R/RW drive, proceed as follows.
1 Push the power button and boot the computer.
5 Do not touch the surface of a disc; hold it by the
edges.
2 After booting the computer, open the disc
compartment by pressing the Eject button.
3 Insert the disc (CD) with the label on the disc
facing upwards and close the disc compartment
by pressing the Eject button.
6 To clean a disc, polish lightly from the inside of the
disc to the outside with a soft cotton cloth.
7 Do not leave the disc compartment open when you
are not using it.
The indicator light comes on.
Play the disc (CD).
Solving Recording Problems
Playing Audio CDs
Run the CD player supplied with Windows or your sound card. You can listen to
the CD by connecting headphones to the appropriate connector. If you have
installed the appropriate player, such as Microsoft Windows Media Player, you can
adjust the volume using the headphone volume control on the drive front panel.
Playing Video CDs
Set up and run the SOFT MPEG program.
If you have any problems recording via your CD-R/RW drive, follow the
appropriate instructions below for the source that you are using.
◆
Hard Drive
1 Check whether the source file is corrupted.
2 Optimize the hard disk by using the Windows defragmenter feature:
Storing and Cleaning Your Discs
To ensure a long service life for your discs and drive, follow the precautions below when storing and cleaning your discs.
1 Do not place a disc in direct sunlight.
2 Store a disc vertically in a well-ventilated and
stable location.
3 Do not write or attach a label on a disc.
START / PROGRAMS / ACCESSORIES / SYSTEM TOOLS / DISC DEFRAGMENTER
3 Decompress the hard disk if it is compressed.
4 Make sure that the space available on the hard disk is at least twice the size
of the largest file to be recorded on the disc.
5 If you wish to record more than 1 000 small files:
First create an image file and copy the image file to the disc; refer to the
section entitled "CD Creation from CD Image" in the CD record utility
documentation
● Choose the low record speed
● Compress small files and then record them
●
4 Do not drop a disc or place heavy objects on it.
10
11
◆
Network Drive
1 Copy the network drive contents to the hard disk and then from the hard disk
to the CD-R/RW drive.
4 Disable the PC’s screen saver. If the screen saver activates while writing data,
the data tramsfer may become too slow, resulting in data writing errors.
5 Close all application programs except writing software.
◆
CD-ROM Drive
6 The CD-R/RW drive supports high-speed recording to High-speed CD-RW
discs. Discs above CD-RW 8X use different rewriting methods and can only be
via the CD-R/RW drive.
1 Clean the source CD, if necessary.
2 Create an image file and then copy the image file to the CD-R/RW drive.
3 Check the CD-ROM drive record speed.
7 When viewing CD-RW 2X properties or performing a full erase, the “WRITE
SPEED 4X DISPLAY” error is displayed unexpectedly. The CD-R/RW drive
has been operating continuously for 20 minutes after completing the full erase.
There are two recording methods :
● Low-speed (file by file)
● High-speed (transfer of an image file from the hard disk)
4 If the transfer speed of the CD-ROM drive is slower than the record speed,
reduce the record speed.
◆
Recommended Disc Types
Others
1 Before starting to record, determine the audio and transfer speeds by using
the [Tool/System Test] option in Easy CD Creator. Then, choose an
appropriate record speed. If the audio speed is less than 2X, first create an
image file on the hard disk.
CD-R
Fujifilm, Kodak, Maxell, Mitsubishi, Mitsui, Pioneer, Ricoh,
SKC, Sony, Taiyo Yuden, TDK, Yamaha
CD-RW
Mitsubishi, Ricoh, SKC
2 To perform a record test before copying to a CD, select the [Test/Copy]
option.
3 If the test fails, try recording on another disc.
12
13
Solving Technical Problems
Problem
Meaning / Solution
After installing the CD-R/RW
drive, the PC gets slower.
◆ Check that the power, audio and IDE cables are
correctly connected to the computer.
◆ Change the IDE cable and reconnect it to the computer.
Preferably, connect a second IDE cable to the CD-R/RW
drive in master mode; see page 7 for further details.
◆ Check the position of the jumper in the master/slave
select terminal.
The CD-R/RW drive is not
recognized by MS-DOS.
◆ Reinstall the device driver or update it with the latest
version by downloading it from the Samsung Web site.
The CD-R/RW drive is not
detected by Windows.
◆ This case may occur when there is a Windows
installation problem; reinstall Windows.
No sound is heard from an
audio CD.
◆ Check whether the audio cable is correctly connected
to the sound output terminal on the CD-R/RW drive and
the sound card CD-IN terminal.
◆ Check that the sound card is operational.
◆ Adjust the volume control.
The CD-R/RW drive is not
detected by the computer.
Technical Specifications
SAMSUNG continually strives to improve its products. Both the design
specifications and these user instructions are thus subject to change without
notice.
Item
Disc
A CD is not read or is read too
slowly.
◆ Install the latest version of the device driver.
◆ Check whether the CD is of good quality and clean it,
if necessary.
The disc compartment will not
open.
◆ Check that the power cable is correctly connected.
SW-216
Disc types supported CD-DA, CD-ROM mode 1, CD-ROM XA mode 2, Form 1, Form 2,
CD-Plus, CD-Extra, Photo-CD (Single, Multi-session), Video CD
in read mode
ready, Enhanced CD, CD-I/FMV, CD-R, CD-RW, CD-TEXT
Disc types supported CD-R, CD-RW
in write mode
Erasing disc types
CD-RW
Disc diameter
12 cm or 8 cm
Data transfer rate
300 KB/sec. (2X), 600 KB/sec. (4X)
1 200 KB/sec. (8X), 2400 KB/sec. (16X)
CR-RW (write mode) 300 KB/sec. (2X), 600 KB/sec. (4X),
1 500 KB/sec. (10X)
CD-R (write mode)
Read mode
4,800 KB/sec. (max.), PIO Mode 4,
DMA Mode 2
CD-RW : 120 ms (typical)
Access time (1/3 stroke)
Drive
Performance
CD
: 110 ms (typical)
Laser
Semiconductor laser
Slide mechanism
Stepping motor
Spindle motor
Brushless motor
◆ Power off and disconnect the PC. Insert a pin or
unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
Load mechanism
Tray. DC motor (Soft Eject).
Error rate
Mode 1: 1 block/1012, Mode 2: 1 block/109
When the MPEG software plays
a Video CD, the pictures are not
regular and the running speed is
too slow.
◆ Adjust the size of the replay screen.
Eject button
Auto eject or Auto inject
◆ After checking the display resolution, adjust it, if
necessary.
Indicator (LED)
Green when playing or recording a disc
Headphone output
Stereo mini-jack (Ø 3.6 mm) 0.60±20% (vrms) 33 Ω
The Disc is not in message is
displayed even though a disc
has been inserted.
◆ The computer may not recognize the disc if you start
playback too quickly after inserting the disc.
Open and close the disc compartment and try again.
◆ Clean the disc and try again.
The CD-R/RW drive is not
detected after it is connected to
a sound card.
◆ The interface mode of the sound card is AT-BUS.
You must therefore connect the CD-R/RW drive to the
IDE port on the PC mother board, rather than to the
sound card, or install an IDE-compatible sound card.
Front Panel
Dial type
Required power
+5 VDC: 1.5 A (max.), +12 VDC: 1.5 A (max.)
Interface connector ATAPI (EIDE)
Rear Panel
Operating
Environment
General
Reliability
14
Volume control
Audio output
Line out 0.70 ± 20% (vrms): 47 KΩ
Jumper block
Device configuration jumper
Operations
Temperature: 5~45°C
Humidity: 10~80%
Storage
Temperature: -25~55°C
Humidity: 10~90%
Dimensions
149 (W) x 42 (H) x 200 (D) mm (including bezel)
Net weight
MTBF
860 g
125 000 POH (20% duty)
15


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2001:04:18 09:20:18
Producer                        : Acrobat Distiller 4.0 for Macintosh
Creator                         : QuarkXPress E: LaserWriter 8 8.5.1
Author                          : ckm
Title                           : 01.SW-216-eng
Modify Date                     : 2001:04:18 09:20:28+09:00
Page Count                      : 9

EXIF Metadata provided by EXIF.tools