Samsung Electronics Co WDG720M Wi-Fi Transmitter Module User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	2379628
Application ID	AS6k14j2gu0GxBqOBPvX/A==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.02kB (162753 bits)
Date Submitted	2014-09-05 00:00:00
Date Available	2015-03-04 00:00:00
Creation Date	2014-06-10 13:56:18
Producing Software	Acrobat Distiller 9.2.0 (Windows)
Document Lastmod	2014-06-10 13:56:18
Document Title	Microsoft Word - WDG720M_User Manual for FCC_IC__Rev1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Will

Manual For WDG720M
SAMSUNG ELECTRONICS CO., Ltd.
Wi-Fi module(2.4GHz, 5GHz, a/b/g/n)
- Model name : WDG720M
- Operation Temperature : -10℃ ~ +70℃
- Power : +5V ±5% (+4.75V ~ +5.25V)
1. Introduction
WDG720M is a USB embedded module compliant with IEEE802.11n standard.
Thecore chipset is from MTK, part number is RT3572L.
2. Operational Description
WDG720M is the 802.11a/b/g/n RF Module, that acts as a communication hub for users of a
wirelessdevice to connect to a wired LAN.
MIMO type
Product type: WLAN (11b mode: 1TX, 1RX, 11g mode: 1TX, 1RX, 11n mode: 2TX, 2RX)
Time base of the transmission frequency
For IF and RF frequency, Crystal is a clock reference.
Synthesizer
Synthesizer inside Transceiver. Internal voltage controlled oscillator (VCO) provides the desired
LOsignal base on the phase-locked loop (PLL) with a relatively wide tuning range for this
application.
Transmission
Base-band Processing (BBP) IC has DSSS (BPSK/QPSK/CCK) and OFDM
(BPSK/QPSK/16QAM/64QAM) modulation function, it provides transmission data rate are 1, 2,
5.5, 11Mbps on DSSS and 6, 12, 18, 24, 36, 48, 54 Mbps on OFDM. Digital data signal will be
converted toanalog (TX IQ) signals through DAC in BBP IC, TX IQ pass through to low pass
filter. TX I/Q signaluse direct conversion (zero-IF) architecture converter to generate carrier
frequency signal. TransceiverIC and internal PA magnify output power.
Receiver
Reverse direction isolation of LNA inside Transceiver IC suppresses unwanted radiation. Then
RFsignal will bedirectly down to IF signal (RX IQ) and high frequency spurious emissions are
suppressed by LPF. Atlast RX IQ signal will be demodulated digital data.
Base band Processing
1. Channel selection is controlled by BBP IC to support data modulation:
- DSSS (BPSK/QPSK/CCK)
- OFDM (BPSK/QPSK/16QAM/64QAM)
Power Control Level
It uses closed-loop power control function to limit RF output power level.
Transmit/Receive Switch
EUT has Transmit/Receive Switch and Antenna switch. End user can’t select any power setting.
Channel Selection Restriction
For product available in the USA/Canada/Taiwan market, only channel 1~11 can be operated.
Selectionof other channels is not possible. But product also could be available in the
Europe/Japan market,channel 1~13 can be operated under the manufacturer change the different
driver.
Data Rate Control
The operation date rate is changing during data transfer base on the optimization of driver.
Discontinue Transmitting with absence of Data or operational failure states
“The device shall automatically discontinue transmission in case of either absence of information
totransmit or operational failure. These provisions are not intended to preclude the transmission
of controlor signaling information or the use of repetitive codes used by certain digital
technologies to completeframe or burst intervals. Applicants shall include in their application for
equipment authorization adescription of how this requirement is met.” Data transmission is
always initiated by software, which isthen passed down through the MAC, through the digital and
analog baseband, and finally to the RF chip.
Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. These are the only
waysthe digital baseband portion will turn on the RF transmitter, which it then turns off at the end
of thepacket. Therefore, the transmitter will be on only while one of the aforementioned packets
is beingtransmitted.
Product Details
> Data Modulation OFDM (BPSK / QPSK / 16QAM / 64QAM)
> Frequency : 2.4GHz and 5GHz
> 802.11 a/b/g/n MIMO Type
>Power : +5V ±5% (+4.75V ~ +5.25V)
Approval Statement
CE Statement
Hereby, we declare that this device is in compliance with the essential requirements and other relevant provisions
of directive 1999/5/EC.
FCC approval
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable
operation.
To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
Contains Transmitter module FCC ID: A3LWDG720M
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
IC approval
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise
aux deux conditions suivantes:
(1) cet appareil ne peut causer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l'appareil.
The host device must be labeled to display the Industry Canada certification number of the module.
Contains transmitter module IC:649E-WDG720M
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module.
Contient module émetteur IC :649E-WDG720M
IMPORTANT NOTE
This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This
device should be installed and must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device is intended only for OEM integrators under the following conditions:
1) This module may not be co-located with any other transmitters or antennas.
2) The antenna must be installed such that 20cm is maintained between the antenna and users.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator
is still responsible for testing their end-product for any additional compliance requirements with this module
installed.
In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered
valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product including this module and obtaining separate FCC & IC
authorizations.
Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environnement non
contrôlé. Cet appareil doit être installé et ne doit pas être co-localisées ou opérant en conjonction avec une autre
antenne ou un autre émetteur.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes :
1 ) L' antenne doit être installée de telle sorte que 20 cm est maintenue entre l'antenne et les utilisateurs .
2 ) Ce module ne peut pas être co-localisé avec d'autres émetteurs ou des antennes .
Aussi longtemps que deux conditions précitées sont remplies, le test du transmetteur supplémentaires ne seront
pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leurs produits finis pour toutes les
exigences de conformité supplémentaires avec ce module installé.
Dans le cas où ces conditions ne peuvent pas être remplies, alors la FCC et IC autorisations ne sont plus
considérés comme valides et l'ID de la FCC ne peut pas être utilisé sur le produit final. Dans ces circonstances,
l'intégrateur OEM sera responsable de réévaluer le produit final, y compris l'obtention de ce module et séparée
de la FCC et IC autorisations
User Information
Caution: Any changed or modifications not expressly approved by the party responsible for compliance could
void the user`s authority to operate this equipment.
Attention: Toute changé ou modifications non expressément approuvés par la partie responsable de la
conformité pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement.
This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band.
Cet appareil est restreint à l'utilisation à l'intérieur seulement dans la bande 5.15 ~ 5.25GHz.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Will
Create Date                     : 2014:06:10 13:56:18+09:00
Modify Date                     : 2014:06:10 13:56:18+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Title                           : Microsoft Word - WDG720M_User Manual for FCC_IC__Rev1
Creator                         : Will
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Document ID                     : uuid:5bf318da-1277-448f-9223-97aca32c9ad9
Instance ID                     : uuid:abf715b5-0618-4149-a795-e0273b44823c
Page Count                      : 4

EXIF Metadata provided by EXIF.tools