Samsung Electronics Co WRGN44M WiFi module User Manual WRG N44M x

Samsung Electronics Co Ltd WiFi module WRG N44M x

User Manual

1 SAMSUNG ELECTRONICS Co., Ltd. SAMSUNG ELECTRONICS Co., Ltd.
2 SAMSUNG ELECTRONICS Co., Ltd. Contents 1 Introduction 2 Wireless Module Specification 2.1 General 2.2 Electric 2.3 Mechanical 2. Hardware Configuration 3 Antenna Spec 3.1 Antenna Type 3.2 Mechanical Structure 3.3 Operating Frequency & S Parameter 3.4 Antenna Pattern & Gain 4 Regulatory Notice 4.1 United States (FCC Notice) 4.2 Canada (IC Notice) 4.3 Installation Procedure
3 SAMSUNG ELECTRONICS Co., Ltd. 1 Introduction This document is manual for WRG-N44M Wireless Module 2 Wireless Module We can control Wireless Module via External Controller PCB including digital appliance (for example, Air conditioner, Washer, Dryer, Refrigerator, Dryer, Oven) Wireless operation is possible by using internal chip (2.4 GHz IEEE802.11) 2.1 General General Model Wireless Module P/N WRG-N44M Host Interface UART Communication IEEE 802.11 b/g/n20/n40 Accessories Case MCU RTL8196C RF IC RTL8188 Antenna Type PIFA
5 SAMSUNG ELECTRONICS Co., Ltd. 2. Hardware Configuration Top View Bottom View 5-Pin Connector Status LED: WiFi Connection Indicator (On/Off)
6 SAMSUNG ELECTRONICS Co., Ltd. 3 ANTENNA SPEC 3.1 Antenna Type PIFA Antenna 3.2 Mechanical Structure
7 SAMSUNG ELECTRONICS Co., Ltd. 3.3 Operating Frequency & S Parameter - Operating Frequency : 2.45 GHz - S Parameter BW1 = 140 MHz (2.36~2.5 GHz) at 10 dB RL BW2 = 740 MHz (2.35~3.09 GHz) at 10 dB RL S21 = -7.25 dB at 2.45 GHz
8 SAMSUNG ELECTRONICS Co., Ltd. 3.4 Antenna Pattern and Gain
9 SAMSUNG ELECTRONICS Co., Ltd. 4 Regulatory Notice 4.1 United States (FCC Notice) FCC ID: A3LWRGN44M In accordance with FCC Part 15, the A3LWRGN44M is listed as a Modular Transmitter Device. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC STATEMENT: This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a different circuit from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. FCC RADIATION EXPOSURE STATEMENT: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
10 SAMSUNG ELECTRONICS Co., Ltd. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains FCC ID: A3LWRGN44M ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 4.2 Canada (IC Notice) IC: 649E-WRGN44M The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IC RADIATION EXPOSURE STATEMENT: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains IC : 649E-WRGN44M ".
11 SAMSUNG ELECTRONICS Co., Ltd. 4.3 Installation Procedure 1. Be sure to use the proper antistatic handling techniques. 2. Insert the module into the case and fix it by bracket. Side view Top view

Navigation menu