Samsung Electronics Co WSNFM400A00 NFC Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2256432
Application ID	n54yzLMYr6wQQXV0s3+UtA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.42kB (205216 bits)
Date Submitted	2014-05-01 00:00:00
Date Available	2014-10-28 00:00:00
Creation Date	2014-04-29 08:05:31
Producing Software	Acrobat Distiller 9.2.0 (Windows)
Document Lastmod	2014-04-29 08:05:31
Document Title	Microsoft Word - User Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Will

Manual for WSNFM400A00 NFC module
1. Introduction
WSNFM400A00 is applied to 13.56MHz contactless communication, including NFC functions.
The core chipsets are from TI, part number TRF7970A and MSP430F5529.
1. 1 Product Information
- Model name : WSNFM400A00
- Operation Temperature : -20℃ ~ +70℃
- Power : +5V ±10% (+4.5V ~ +5.5V)
2. Installation
This NFC module must be installed in a device and not allow the user to replace nor modify it.
5 Pin Connector
Version 1.0
Samsung Electronics
page 1 of 4
A HUB and dongle connected to
USB TO MINI USB cable
A HUB and dongle connected to 5pin cable
Version 1.0
Samsung Electronics
page 2 of 4
FCC approval
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable operation.
To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
Contains Transmitter module FCC ID: A3LWSNFM400A00
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
IC approval
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux deux
conditions suivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil doit accepter toute interférence, y
compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.
The host device must be labeled to display the Industry Canada certification number of the module.
Contains transmitter module IC: 649E- WSNFM400A00
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module.
Contient module émetteur IC : 649E- WSNFM400A00
Version 1.0
Samsung Electronics
page 3 of 4
User information
Caution: Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s
authority to operate this equipment.
Attention: Toute changé ou modifications non expressément approuvés par la partie responsable de la conformité
pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement.
IMPORTANT NOTE
This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device should
be installed and must not be co-located or operating in conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:
1)
The antenna must be installed such that 20 cm is maintained between the antenna and users,
2)
The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements with this module installed.
In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the
FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product including this module and obtaining separate FCC & IC authorizations.
NOTE IMPORTANTE
Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environnement non contrôlé. Cet
appareil doit être installé et ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou un autre
émetteur.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes :
1)
Ce module ne peut pas être co-localisés avec les autres émetteurs ou les antennes.
2)
Ce module ne peut pas être co-localisé avec d'autres émetteurs ou des antennes .
Aussi longtemps que deux conditions précitées sont remplies, le test du transmetteur supplémentaires ne seront pas tenus.
Toutefois, l'intégrateur OEM est toujours responsable de tester leurs produits finis pour toutes les exigences de conformité
supplémentaires avec ce module installé.
Dans le cas où ces conditions ne peuvent pas être remplies, alors la FCC et IC autorisations ne sont plus considérés
comme valides et l'ID de la FCC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera
responsable de réévaluer le produit final, y compris l'obtention de ce module et séparée de la FCC et IC autorisations
Version 1.0
Samsung Electronics
page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Will
Create Date                     : 2014:04:29 08:05:31+09:00
Modify Date                     : 2014:04:29 08:05:31+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - User Manual
Creator                         : Will
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Document ID                     : uuid:9b6bf54a-ca2b-4858-ba2b-8f6150c96493
Instance ID                     : uuid:fa13ee9f-a5a9-48a9-b4b1-c902ab7d4009
Page Count                      : 4

EXIF Metadata provided by EXIF.tools