Sanwa Electronic Instrument Co RM-Y822A Remote Control Transmitter User Manual manual
Sanwa Electronic Instrument Co Ltd Remote Control Transmitter manual
manual
4-097-333-21
© 2003 Sony Electronics.
Reproduction in whole or in part without written
permission is prohibited. All rights reserved. SAT-HD300
FCC ID:L73RM-Y822A
USER'S MANUAL
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
This product must not be exposed to dripping or splashing liquids. Objects filled with liquids, such as a vase, must not be placed on or above
the product.
NOTE TO CABLE/TV/SATELLITE DISH INSTALLER:
This reminder is provided to call the cable TV system/satellite dish installer’s attention to Article 820-40 of the National Electric Code (U.S.A.).
The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding sys-
tem of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION : FCC PART 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manu-
al, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFI-
CIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPOR-
TANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
WARNING:
TO REDUCE THE RISK OF ELECTRONIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
1
2
REGULATORY INFORMATION: FCC Part 68
Sony must make any necessary repairs to the modem portion of this equipment in order to maintain valid FCC registration. Do not attempt to
repair or service the modem.
This equipment cannot be used on public coin service provided by the Telephone Company. Connection to Party Line Service is subject to state
tariffs.
• This product complies with Part 68 of the FCC rules. On the back of this product is a label that contains, among other information, the FCC
registration number and Ringer Equivalent Number (REN) for this product. If requested, this information must be provided to the telephone
company.
• The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line
may result in the devices not ringing in response to an incoming call. Typically, the sum of the RENs should not exceed five (5). To be certain
of the number of devices that may be connected to the line (as determined by the total RENs) contact the local telephone company.
• If this product causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is necessary.
• The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the prod-
uct. If this happens, the telephone company will provide advance notice so you can make the necessary modifications to maintain uninter-
rupted service.
• Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission, or corpo-
rate commission for information.)
• If trouble is experienced with this product, for repair or warranty information, please contact Sony Electronics Inc. If the product is causing
harm to the telephone network, the telephone company may request that you disconnect the product until the problem is resolved.
• An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the tele-
phone network or premises wiring using a compatible modular jack which is Part 68 compliant. See installation instructions for details.
If you have questions about this Sony product, please contact the Sony Satellite System Information Center at 1-800-838-SONY(7669).
For questions about service, programming or billing, contact DIRECTV at 1-800-DIRECTV (347-3288).
CAUTION
DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY WITHOUT WRITTEN AUTHORIZATION FROM SONY ELECTRONICS CORPORATION.
UNAUTHORIZED MODIFICATION COULD VOID THE USER’S AUTHORITY TO OPERATE THIS PRODUCT.
THIS EQUIPMENT IS INTENDED TO RECEIVE AND DECODE SIGNALS TRANSMITTED ACCORDING TO ATSC DIGITAL TELEVISION STANDARD
A/53, DIRECTV®SPECIFICATION AND IS INTENDED TO BE USED WITH AN APPROPRIATE ANTENNA, DISH AND DISPLAY DEVICE THAT YOU
MUST PROVIDE.
Dolby Digital®
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.
Macrovision Information
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited pay-per-view uses unless oth-
erwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Declaration of Conformity
Trade Name: Sony
Model No.: SAT-HD300
Responsible Party: Sony Electronics Inc.
Address: 680 Kinderkamack Road, Oradell, NJ 07649
Telephone No.: 201-930-6972
As an ENERGY STAR®Partner,
Sony has determined that
this product or product models
meets the ENERGY STAR®
guidelines for energy
efficiency.
ENERGY STAR®is a U.S. registered mark.
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MAN-
UAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for
installation, use, and servicing.
This unit does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and
operating instructions should be read before the
product is operated.
2. Keep these instructions. - The safety, operating
and use instructions should be retained for future
reference.
3. Heed all warnings. - All warnings on the product
and in the operating instructions should be adhered
to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this apparatus near water. – For
example: near a bath tub, wash bowl, kitchen sink,
laundry tub, in a wet basement; or near a swimming
pool; and like.
6. Clean only with dry cloth. – Unplug this product
from the wall outlet before cleaning. Do not use liq-
uid cleaners.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
-
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The
openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in instal-
lation such as a bookcase or rack unless proper ven-
tilation is provided or the manufacturer’s instructions
have been adhered to.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other appa-
ratus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polar-
ized or grounding-type plug. A polarized plug
has two
blades with one wider than the other.
A grounding
type plug has two blades and a
third grounding prong. The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet, con-
sult an electrician for replacement of the obso-
lete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with apparatus. When a cart is used, use cau-
tion when moving the cart/ apparatus combi-
nation to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14.
Refer all servicing to qualified service person-
nel.
Servicing is required when the apparatus
has been damaged in any way, such as
power- supply cord or plug is damaged, liquid
has been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
IMPORTANT SAFETY INSTRUCTIONS
3
4
IMPORTANT INFORMATION
Due to copyright restrictions, you may not be able to view some high definition programs in
high definition format using this product. If HD viewing is prohibited due to copyright restric-
tions, you would need to connect SD interfaces to view the program.
In certain markets, access to local channels requires a DIRECTV®Multi-Satellite Dish Antenna.
For the most current information about the availability of local channels in your area, contact
your retailer or visit DIRECTV.com. For access to all High Definition programming, a triple LNB
Multi-Satellite dish antenna, including a Sat C LNB, is required, along with a High Definition
capable DIRECTV®HD Receiver and High Definition television. Satellite Dish Antenna Sold
Separately.
Activation of programming may be subject to credit approval and requires valid service
address, social security number and/or major credit card. Deposit or prepayment may be
required. Programming subject to change. You must be physically located in the U.S. to receive
DIRECTV service. DIRECTV services not available outside the U.S. DIRECTV programming is
sold separately and independently of DIRECTV System hardware. A valid programming sub-
scription is required to operate DIRECTV System hardware. Activate your DIRECTV program-
ming today at 1-800-DIRECTV (1-800-347-3288)
DIRECTV, the Cyclone Design logo and Advanced Program Guide™ are trademarks of DIRECTV,
Inc., a unit of Hughes Electronics Corp., and are used with permission.
Sony Hi-Scan and the Sony logo are registered trademarks of Sony.
Sony Software License Agreement
ATTENTION:USE OF THE SOFTWARE IS SUBJECT TO THE SONY SOFTWARE LICENSE TERMS
SET FORTH ON PAGE 121. USING THE SOFTWARE OR THE PRODUCT IN WHICH IT IS INCOR-
PORATED INDICATES USER’S ACCEPTANCE OF THESE LICENSE TERMS. IF THE USER DOES
NOT ACCEPT THESE LICENSE TERMS,THE USER SHOULD IMMEDIATELY RETURN THE ENTIRE
PRODUCT IN ITS ORIGINAL PACKAGING IN ORDER TO RECEIVE A FULL REFUND OF THE PUR-
CHASE PRICE.
5
TABLE OF CONTENTS
Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .3
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
1. Introduction 1-1. A New World of Digital Entertainment . . . . . . . . . . . . . . . .7
1-2. Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2. Important Overview 2-1. Sending Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2-2. TV Signal Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2-3. Display Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2-4. Normal and Wide Format Signals . . . . . . . . . . . . . . . .12-13
2-5. Audio Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
2-6. On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17
3. Setup and Connections 3-1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
3-2. Back Panel of the DIRECTV®HD Receiver . . . . . . . . . .20-21
3-3. General Recommendations . . . . . . . . . . . . . . . . . . . . . . . .22
3-4. Connecting to Antennas . . . . . . . . . . . . . . . . . . . . . . .23-26
3-5. TV Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27-30
3-6. VCR Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-32
3-7. Audio Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .33-34
3-8. Remote Control RF Antenna Connection . . . . . . . . . . . . . .35
4. Front Panel and 4-1. Using the Front Panel of the DIRECTV®HD Receiver . . . . .36
4-2. Using the Remote Control . . . . . . . . . . . . . . . . . . . . . .37-39
4-3. Programming the remote control . . . . . . . . . . . . . . . . . . . .40
4-4. Remote Control Codes for Other Components . . . . . . .41-42
5. Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
6. Basic Operation 6-1. Viewing the Channel Banner . . . . . . . . . . . . . . . . . . . .44-45
6-2. Surfing Favorite Channels . . . . . . . . . . . . . . . . . . . . . . . . .46
6-3. Freeze Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
6-4. Subscription to DIRECTV®programming and
ANT/CABLE-Only operation . . . . . . . . . . . . . . . . . . . . . . .48
6
7.
Advanced Program Guide™
7-1. About the Advanced Program Guide™ . . . . . . . . . . . . . . .49
7-2. Layout of the Advanced Program Guide™Screen . . . .50-51
7-3. Moving through the Advanced Program Guide™ . . . . .52-53
7-4. Selecting a Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
7-5. Getting More Program Information . . . . . . . . . . . . . . .55-56
7-6. Setting a Timer/Record Event for Future Viewing . . . . . . .57
7-7. Purchasing DIRECTV®Pay Per View Programs . . . . . . . . . .58
7-8. Searching for Programs by Category . . . . . . . . . . . . . .59-60
7-9. Searching for Programs by Keyword . . . . . . . . . . . . . . . . .61
8. Customization 8-1. Accessing the On-screen Menu . . . . . . . . . . . . . . . . . . . .62
8-2. The structure of the On-Screen Menu . . . . . . . . . . . . . . . .63
8-3. Managing Program Purchases . . . . . . . . . . . . . . . . . . . . .64
8-4. Checking the Messages . . . . . . . . . . . . . . . . . . . . . . . . . .65
8-5. Setting a Timer/Record Event . . . . . . . . . . . . . . . . . . . . . .66
8-6. Modifying a Timer/Record Event . . . . . . . . . . . . . . . . . . . .67
8-7. Initializing the System . . . . . . . . . . . . . . . . . . . . . . . . .68-75
8-8. Managing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . .76-79
8-9. Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80-81
8-10. Setting Default Signal Out . . . . . . . . . . . . . . . . . . . . . . .82
8-11. Hook-up Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
8-12. Setting the Audio . . . . . . . . . . . . . . . . . . . . . . . . . . .84-88
8-13. Choosing the Aspect Ratio . . . . . . . . . . . . . . . . . . . . .89-91
8-14. Setting Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . .92
8-15. Setting Digital Caption Style . . . . . . . . . . . . . . . . . . . . . .93
8-16. Setting Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . .94
8-17. Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
8-18. Running Auto Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
8-19. Setting Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97-102
8-20. Getting the System Information . . . . . . . . . . . . . . .103-106
8-21. Testing the System . . . . . . . . . . . . . . . . . . . . . . .107-109
8-22. Replace Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
8-23. VCR Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
8-24. Remote Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . .112
9. Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113-114
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116-119
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Software License Agreement . . . . . . . . . . . . . . . . . . . . . . . . .121
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
7
1-1. A New World of Digital Entertainment
Welcome to the SAT-HD300 DIRECTV®HD Receiver, an advanced digital satellite receiver that show-
cases a new generation of digital entertainment.
The DIRECTV HD Receiver delivers a variety of programs from DIRECTV and has a built-in HD Receiver
that serves as a digital receiver that makes it possible to view digital programs even on your analog TV.
The Advanced Program Guide™ delivered via satellite service also enables you to access and view
over-the-air broadcasts and cable as well as DIRECTV®programming.
1. INTRODUCTION
8
Ultimate Entertainment
•A Wide Variety of Programs
Hundreds of channels are available by subscription from DIRECTV.
•DIRECTV Advanced Program GuideTM
Instant access to up to seven days of program listings.
Ability to jump a day or 6 hours at a time.
Ability to search and tune by program title, keyword and category.
Technical Flexibility
•Seamless Tuning
Tune seamlessly to over-the-air, cable and satellite.
•Multiple Output Jacks
Multiple output jacks are provided on the back panel of the DIRECTV®HD Receiver ensuring
maximum connectively to a variety of display devices.
•Screen Format Adaptability
Various screen formats are available including 1080i, 720p, 480p, 480i, variable 1, variable 2,
variable 3, auto DVI, and true native modes.
•ANT/CABLE Only Mode
Viewing analog/digital broadcasting with an over-the-air antenna and cable service.
•Simultaneous 480i Display Output
Supporting simultaneous 480i Display Output for VCR-recording or viewing on an analog TV.
Superior Performance
•Crisp Picture
High-Definition or resolution with a 16:9 aspect ratio when connected to a high definition moni-
tor.
•Superior Sound
Sensational sound with Dolby Digital®5.1 channels when connected to a Dolby Digital®compati-
ble audio receiver system.
•DVI-HDTV Output
For an all-digital connection to DVI-HDTV monitors.
•RF Remote Control
Remote control access from outside a cabinet or even from another room within your home.
Convenient Use
•Help
Easy-to-use on-screen menus with instant spot help and brief on-screen user’s guide.
•Hook-up Help
The on-screen menus show connection schemes on the DIRECTV HD Receiver.
•Setup Wizard
Easy-to-use Wizard based System Setup
•Easy Recording to VCR
Up to seven days of program guide information from which shows can be quickly selected for
automatic VCR recording.
1-2. Main Features
2-1. Sending Signals
9
2. IMPORTANT OVERVIEW
Digital broadcasting is a new way of sending programs over the airwaves with superior qual-
ity video and audio. The DIRECTV®HD Receiver enables you to take full advantage of digital
broadcasting. To fully enjoy it, it is helpful understand the ways the program signals are sent.
There are two types of TV signal formats; analog (often called NTSC format; National Television
System Committee) and digital (ATSC format; Advanced Television System Committee). Digital
formats are classified into three categories: High Definition (HD), Enhanced Definition (ED), and
Standard Definition (SD) according to the resolution or digital picture quality.
There are also three ways that program signals can be received; over-the-air (NTSC, ATSC),
cable (analog and digital), and satellite.
This receiver contains a QAM tuner which should allow you to receive unscrambled QAM dig-
ital television programming via subscription service to a cable service provider. This receiver
will not be able to tune encrypted (scrambled) digital programming or advanced interactive
digital cable services. Contact your local cable service provider for further information regard-
ing the availability of unscrambled digital cable programming.
TV
HD Receiver
Phone
Jack
Digital
signal
Analog
signal
DIRECTV
Sat A 101 Sat B 110 Sat C 119
Satellite
Unscrambled
Analog Cable service
Unscrambled
Digital Cable service
Signal Format Analog Digital
SD HD
10
2-2. TV Signal Formats
The digital TV standards allow several different formats. Broadcasters can choose between
three formats:
• 480p - The picture is 704 x 480 pixels, sent at 60 complete frames per second (480i is
also possible).
• 720p - The picture is 1280 x 720 pixels, sent at 60 complete frames per second.
• 1080i - The picture is 1920 x 1080 pixels, sent at 60 interlaced frames per second (30
complete frames per second).
(The “p” and “i” designations stand for “progressive” and “interlaced.” In a progressive for-
mat, the full picture updates every sixtieth of a second. In an interlaced format, half of the pic-
ture updates every sixtieth of a second.)
The 480p and 480i formats are called the SD formats, and 480i is roughly equivalent to a nor-
mal analog TV picture. The 720p and 1080i formats are called the HD formats.
Some analog televisions can display a picture 720 pixels wide by 480 pixels high, that’s a total
of 345,600 pixels. HD digital signals can have a maximum resolution of 1920 x 1080, that’s
2,073,600 pixels, or six times more pixels than the older resolution. Pictures will be crisper and
cleaner, with more detail in every close-up and every panorama.
Standard Comparison Table
Active Lines 480i 480p 720p or 1080i
Sound Stereo (2 ch) Dolby Digital®(5.1 ch) Dolby Digital (5.1 ch)
MPEG Audio (2 ch)
Aspect Ratio 4 : 3 4 : 3 or 16 : 9 16 : 9
Resolution 720 x 480 640 x 480 1280 x 720
704 x 480 1920 x 1080
2. IMPORTANT OVERVIEW
11
2-3. Display Formats
The DIRECTV®HD Receiver provides several display formats. The FORMAT button in the front
panel changes the display format in the cycle of 1080i, 720p, 480p, 480i, native,
variable 1, variable 2, variable 3 and Auto DVI** modes. In 1080i, 720p, 480p and 480i
modes, all input signal formats are converted to the chosen display format. In native, vari-
able 1, variable 2 and variable 3 modes, output display format is automatically adapted
depending on input signal format. In Auto DVI mode, the output display format is automati-
cally adapted based on the preferred resolution format of the DVI-HDTV monitor. The format
may be converted from the original broadcast format.
* Only one of the YPbPr, RGB or DVI-HDTV jacks is available at any one time, depending on
the TYPE switch setting and DVI-HDTV connection status.
** Format available when using the DVI-HDTV output to connect to a DVI-HDTV monitor.
OUTPUT CONNECTION AVAILABLE FORMATS
YPbPr* 1080i/720p/480p/480i/native/variable 1/variable 2/variable 3
RGB* 1080i/720p/480p/native/variable 1/variable 2/variable 3
DVI-HDTV* 1080i/720p/480p/480i/native/variable 1/variable 2/
variable 3/Auto DVI**
Video 1 / 2 All formats converted to 480i
S Video All formats converted to 480i
RF Out to TV All formats converted to 480i
T
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
Pb
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DVI-HDTV OUT
(1080ii/720p/480p/480ii)
(
12
VIDEO OUT
S VIDEO
OUT
OUT TO TV
Display Format modes Input Signal format Output Signal format
1080i all formats 1080i
720p all formats 720p
480p all formats 480p
480i all formats 480i
native 1080i 1080i
720p 720p
480p 480p
480i 480i(Component, DVI), 480p(RGB)
variable 1 1080i 1080i
720p 720p
480p/480i 480p
variable 2 1080i/720p 1080i
480p/480i 480p
variable 3 1080i/720p 720p
1080i 480p
AUTO DVI** all formats changes according to monitor type
12
2-4. Normal and Wide Format Signals
When you view a high definition picture with 480i or 480p format setting, the WIDE MODE but-
ton on the remote control changes the wide mode in the cycle of Letterbox, Cropped, to
Squeezed.
When you view a standard definition picture with 720p or 1080i format setting, the WIDE
MODE button on the remote control changes the wide mode in the cycle of Normal, Wide,
Panorama, Zoom, to Cine-Zoom. (Refer to section 8-13, ‘Choosing the Aspect Ratio’)
Standard Definition
Standard Definition Output Format
No Adjustment Options
High Definition
WHEN YOU SET THE FORMAT TO SDTV (480i/480p)
Letter box
Choose when you want to view a
wide format (16:9) picture on a nor-
mal screen (4:3) without squeezing.
Cropped
Choose when you want to view a
picture filling the entire screen
while keeping the wide format.
Left and right portions of the pic-
ture will not be shown.
Squeezed
Choose when you want to view a full
picture filling the entire screen with
no black bars. The picture in a 16:9
format will be horizontally adjusted or
squeezed to fit the 4:3 ratio monitor.
This setting can also be useful when
used with 16:9 aspect ratio monitors
or with 4:3 aspect ratio monitors with
a “16:9 enhancement” feature.
antenna
Program Format
13
2. IMPORTANT OVERVIEW
2-4. Normal and Wide Format Signals
WHEN YOU SET THE FORMAT TO HDTV (1080i/720p)
Normal
Choose when you want to view a picture
with an original 4:3 aspect ratio on your
16:9 TV. Black or gray bars will show at the
left and right sides.
Wide
Choose when you want to evenly stretch the
width of a normal picture to fill the entire
screen.
Panorama
Choose when you want to evenly stretch the
edges of a normal picture to fill a wide
screen.
Zoom
Choose when you want to fill the entire
screen with the picture. The image will be
altered both horizontally (stretched) and
vertically (cropped). The top and bottom
portions of the picture will not be shown.
Zoom1 shows you the picture with a trade-
off between distortion and screen coverage.
CINE-Zoom
Choose when you want to adjust zooming.
Standard Definition
High Definition
*Three temporary adjustment options available
Adjustment
Required
antenna
Program Format High Definition Output Format
*Note.
The HDTV formats should always be broadcast in the 16:9 aspect ratio.
However, you may choose one of three temporary options to select for your
preference. The three options are Standard , Expand and Shrink.
14
2-5. Audio Signals
Dolby Digital Sound with 5.1 Channels
sub-woofer
right
speaker
left
speaker
center channel
speaker
surround
sound
speaker
surround
sound
speaker
Digital Audio Signals
The DIRECTV®HD Receiver will be the focal center of your home entertainment system comprising a
variety of components, such as TV, DVD, VCR, etc. and external audio systems. Since digital programs
being broadcast contain digital-quality audio, you can create a home theater by sending audio signals
from the DIRECTV HD Receiver to your audio system externally. HD digital signals use the Dolby
Digital®audio encoding system - the same digital sound used in many movie theaters, on DVDs, and
in many home theater systems.
When you tune to a channel, the DIRECTV HD Receiver can send signals either to a Dolby Digital®
decoder/receiver or to a PCM (normal digital) decoder. (* Refer to Section 3-7 Connection for Audio
for making the required external connections to your system.)
Dolby Digital®audio, formally known as Audio Coding 3rd Generation is a
coding technique that can provide up to five independent, full frequency
response audio channels (three in left, center, and right, two in rear left
and right,) and one low frequency effect for a sound you can feel.
GLOSSARY
15
The analog audio outputs may be used to drive an external Hi-Fi audio system instead of the
TV speakers. These stereo outputs are activated by setting the Analog Mode in the Audio
menu to Stereo.
If you set the Analog Mode to SAP (Second Audio Program), you can hear the program’s dia-
log in another language such as French or Spanish, if provided on the analog broadcast.
(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
(1080ii/720p/480p/480i
VIDEO OUT
Analog stereo amplifier
AUDIO IN
Audio cables
Analog Audio Signals
2-5. Audio Signals
2. IMPORTANT OVERVIEW
16
2-6. On-Screen Display
Advanced Program Guide™
The DIRECTV Advanced Program Guide™ is an on-screen listing of current and future pro-
grams that are available from DIRECTV. The DIRECTV®HD Receiver offers you a comprehen-
sive program list that contains information about programs with hundreds of channels, includ-
ing analog Antenna and digital (ATSC). If you do not subscribe to DIRECTV®programming, you
will not be able to see the Advanced Program Guide™.
Main Menu
You can adjust the setup through a user-friendly on-screen menu using the remote control.
While viewing a program, the on-screen menu will appear on your TV screen if you press the
MENU button on your remote control. The on-screen menu is operated using a simple,
straight-forward ‘Highlight and Select’ process. You just highlight a menu item by using
“DEF G ” on your remote control, and select it by pressing “ ”. The on-screen menu also
offers visual cues for easy guidance.
17
3. SETUP AND CONNECTIONS
2-6. On-Screen Display
Help
First, certain features and terminologies used in the on-screen menus require your basic
understanding to fully utilize their capabilities. The DIRECTV®HD Receiver provides a power-
ful feature called “Help” that describes highlighted menu item to help you understand the fea-
tures. Press and hold the “HELP” button to display the “Help”. Once you release the button,
the Help menu disappears from the screen.
Second, if you press the “HELP” button while you are viewing a program with no menus on -
screen, the DIRECTV HD Receiver provides a comprehensive on-screen user’s guide. It
describes how to use your receiver.
This is, in fact, an on-line version of this Operating Guide.
18
3-1. Unpacking
Make sure you have received all these items listed below with the DIRECTV®HD Receiver.
M
E
N
U
MUTING
TV
TV/VIDEO
FAVORITE
FLIP OPEN
FREEZE
CODE SET
SIGNAL WIDE
MODE
HELP CC
PREV CH
CHVOL
GUIDE
INFO
ENTER
PIC MODE
FUNCTION
SAT
SLEEP TV POWER
SAT
E
X
I
T
RM-Y822
S VIDEO Jack
Audio/Video Jacks
OUT TO TV
Phone Jacks
YPB
Component Jacks
DVI-HDTV Jack
PR
VCR
CONTROL
Remote Control Cables
Remote Control
RF Antenna
Batteries
AA
AA
Access Card
ACCESS
CARD
19
3. SETUP AND CONNECTIONS
3-1. Unpacking
DIRECTV®HD Receiver
The DIRECTV HD Receiver is capable of receiving signals from the satellite dish, cable, and/or over-the-air
antenna and sending the decoder signals to your TV.
Remote Control
In addition to the DIRECTV HD Receiver, the remote control can be programmed to control many other
devices.
Batteries
To install the batteries, slide open the battery compartment and insert the two AA batteries provided.
Component Out Jacks and Cables
Component Cables are used to connect the DIRECTV HD Receiver to an industry standard Y/Pb/Pr compat-
ible Monitor.
DVI-HDTV port and Cable
DVI cable is used to connect the DIRECTV HD Receiver to a DVI-HDTV compatible HD monitor.
S-Video Jack and Cable
An S-Video jack is provided on the DIRECTV HD Receiver and is used together with audio cables.
Remember to connect the left and right audio cables. An S-Video jack carries only the picture signals, not
the sound.
Audio/Video Jacks and Cables
The Audio/Video jacks provide good picture and sound quality. They are used for making most Audio/Video
connections between components. The Audio/Video jacks may be color coded (yellow for video, red for
right audio, and white for left audio). If your component has only one input for audio (mono), connect it to
the left (white L/mono) audio jack on the DIRECTV HD Receiver.
RF (Radio Frequency) Jacks and Coaxial Cables (F-type)
RF jacks are necessary for reception of over-the-air broadcasts, cable, and DIRECTV signals. These jacks
are also required for antenna or cable connections. The RF and coaxial jacks on the DIRECTV HD Receiver
are labeled Antenna, Cable, Satellite and OUT TO TV. An RG-6 type coaxial cable is required for satellite
signal distribution.
Telephone Jack and Cord
A telephone line cord is required to connect the DIRECTV HD Receiver to a phone line. If you choose to sub-
scribe to DIRECTV®programming, this phone line is required to be connected.
Access Card
The Access Card is the means by which DIRECTV controls the distribution of its service. The card must be
inserted into the access card slot (on the front of the DIRECTV HD Receiver) at all times to ensure recep-
tion of satellite signals.
Remote Control RF Antenna
The Remote Control RF Antenna can be used with the supplied remote control.
VCR Controller
The VCR Controller allows the Record function to automatically operate your VCR.
20
3-2. Back Panel of the DIRECTV®HD Receiver
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
Ant In
Is used to connect an over-the-air or terrestrial antenna.
Cable In
Is used to connect a coaxial cable coming from your cable TV service outlet or cable box.
Out to TV
Provides an RF connection between the DIRECTV HD Receiver and older TVs. All decoded signals are
provided on channel 3 or 4 as selected in the Output Channel section of the SETUP menu. When the
DIRECTV HD Receiver is in the standby mode, Cable or Antenna signals are passed through as chosen
in the Out to TV section of the Preference menu.
Video Out 1, 2
Is used to provide baseband composite video signal to a VCR or TV set. Video connection generally
provides picture quality that is superior to RF connections. For a better quality picture connection, use
the S-Video jack if it is available.
Component Out
Is used to connect to a Y/Pb/Pr-compatible monitor. Three video and two audio jacks for a Y/Pb/Pr
monitor need to be connected and the TYPE switch must be set to left position.
RGB/DVI-HDTV Out
Is used to connect to either an RGB compatible or DVI-HDTV monitor. Either an RGB port for an RGB
monitor or a DVI-HDTV port for a DVI-HDTV monitor need to be connected and the TYPE switch must
be set to right position.
Note : The DVI-HDTV port has a higher priority when both the RGB and DVI-HDTV ports are connected.
Note: For best access to High-Definition Programming from DIRECTV, connect the DVI-HDTV output to
a DVI-HDTV input on your high-definition TV or monitor. A DVI-HDTV input is one that is compliant
with EIA-861 and HDCP specifications. Check your TV or monitor’s user manual to find out if the TV or
monitor’s DVI input is compliant with these specifications.
21
3. SETUP AND CONNECTIONS
3-2. Back Panel of the DIRECTV®HD Receiver
Audio Out 1,2
Is used to provide analog audio signals to VCR, TV set, HD Monitor, or Hi-Fi System.
Digital Audio Out
Is used to connect a digital optical cable from the DIRECTV HD Receiver to the Dolby Digital®receiver
or decoder. Dolby Digital audio enables the viewer to experience theater-quality sound using up to 5.1
audio channels when available audio in the broadcast.
Data Port
Can be used to communicate with certain compatible devices, such as Personal Video Recorders.
VCR Control
Is used to connect the VCR Controller cable to your receiver.
RF Remote
Is used to connect the RF Remote control antenna to your receiver.
Phone Jack
Is used to connect a phone line.
Satellite In
Is used to connect a satellite dish antenna to your receiver.
22
3-3. General Recommendations
You can connect the DIRECTV®HD Receiver in a variety of configurations. The answers to the follow-
ing questions will determine the correct setup for you.
- What type of antennas do you have? Satellite dish, cable, and/or over-the-air antennas.
- What type of connectors does your TV or VCR have: Y/Pb/Pr, RGB, DVI-HDTV, S-VIDEO, A/V (RCA-
type), or RF coaxial?
- Do you have an external audio or audio/video system? Consider integrating the DIRECTV HD
Receiver into a home theater configuration to take advantage of the audio capabilities of your Dolby
Digital®System (Digital) or Hi-Fi System (Analog).
- Does your TV have Y/Pb/Pr connectors? Use it to connect your TV to the DIRECTV HD Receiver. An
Y/Pb/Pr connection provides a better picture than S-VIDEO, RCA-type video, or RF connections.
- Does your TV have an S-VIDEO jack? Use it to connect your TV to the DIRECTV HD Receiver.
An S-VIDEO connection provides a better picture than RCA-type video or RF connections.
- Does your TV have RCA-type A/V connectors, but no S-video jack? Use your TV’s A/V connectors to
connect your components. An A/V connection provides better picture and audio when compared to
an RF connection.
Although there are numerous connections possible for optimum video and audio performance, try to fol-
low the guidelines listed below when you hook up your components. Detailed hook-up instructions are
provided on the following pages.
Protect your components from power
surges by turning off the component and
unplugging power cords when you make
connections.
Protect your component from overheat-
ing by keeping the ventilation holes
open and not stacking components.
No Dish
Round Dish (Satellite A)
Oval Dish (Satellite A, B)
Oval Dish (Satellite A, B, C)
Analog TV
HD Monitor (Y/Pb/Pr type)
HD Monitor (RGB type)
HD Monitor (DVI-HDTV type)
VCR
Digital Audio System
Analog Hi-Fi System
23
24
25
26
27
28
29
30
31
33
34
To Antennas
To TV/Monitor
To A/V Systems
Connection Component Page
CAUTION: Make all connections before plugging the power supply cord into a standard 120V, 60Hz AC
power outlet.
23
3. SETUP AND CONNECTIONS
3-4. Connecting to Antennas - Non-Satellite Sources
Receiving Signals
1. Connect the “Antenna” to the “ANT IN” jack on the DIRECTV®HD Receiver using a coaxial
RF cable.
2. Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a
coaxial RF cable.
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
Antenna
Cable TV
wall jack
24
3-4. Connecting to Antennas - Round Dish (Satellite A)
Receiving Signals
1.
Connect the “Antenna” to the “ANT IN” jack on the DIRECTV
®
HD Receiver using a coaxial RF cable.
2.
Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a coaxial RF
cable.
3.
Connect the “Jack 1” of the dish antenna to the “SATELLITE IN” jack on the DIRECTV HD Receiver using
a coaxial RF cable. (For proper dish installation, refer to the “Installer’s Guide” provided with your satel-
lite dish antenna.)
4.
Connect the “Phone Wall Jack” to “PHONE JACK” on the DIRECTV HD Receiver using a phone cable.
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
LNB
Sat A
Dish
Jack 1
Phone wall jack
Antenna
Cable TV
wall jack
NOTE
While you are subscribing to a DIRECTV®pro-
gramming package, you can still view over-the-
air and cable TV programs, if you make con-
nections to the over-the-air and/or cable jacks.
NOTE
A triple LNB multi-satellite dish with a SAT
C LNB is required to receive all DIRECTV®
High-Definition programming, along with
this DIRECTV HD Receiver.
25
3. SETUP AND CONNECTIONS
3-4. Connecting to Antennas - Oval Dish (Satellite A, B)
Receiving Signals
1.
Connect the “Antenna” to the “ANT IN” jack on the DIRECTV
®
HD Receiver using a coaxial RF cable.
2.
Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a coaxial RF cable.
3.
Connect the “Jack 1” of the multi-switch to the “SATELLITE IN” jack on the DIRECTV HD Receiver using
a coaxial RF cable. (For proper dish installation, refer to the “Installer’s Guide” provided with your satellite
dish antenna.)
4.
Connect the “Phone Wall Jack” to “PHONE JACK” on the DIRECTV HD Receiver using a phone cable.
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
LNB
Sat B
LNB
Sat A
Dish
5x4 Multi-switch
Output
Phone wall jack
Antenna
Cable TV
wall jack
NOTE
While you are subscribing to a DIRECTV®
programming package, you can still view
over-the-air and cable TV programs, if you
make connections to the over-the-air and/or
cable jacks.
NOTE
A triple LNB multi-satellite dish with a SAT
C LNB is required to receive all DIRECTV®
High-Definition programming, along with
this DIRECTV HD Receiver.
26
3-4. Connecting to Antennas - Oval Dish (Satellite A, B, C)
Receiving Signals
1.
Connect the “Antenna” to the “ANT IN” jack on the DIRECTV
®
HD Receiver using a coaxial RF cable.
2.
Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a coaxial RF cable.
3.
Connect the “Jack 1” of the multi-switch to the “SATELLITE IN” jack on the DIRECTV HD Receiver using a
coaxial RF cable. (For proper dish installation, refer to the “Installer’s Guide” provided with your satellite dish
antenna.)
4.
Connect the “Phone Wall Jack” to “PHONE JACK” on the DIRECTV HD Receiver using a phone cable.
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
Phone wall jack
LNB
Sat B
LNB
Sat C
LNB
Sat A
Dish
5x4 Multi-switch*
Output
Antenna
Cable TV
wall jack
NOTE
While you are subscribing to a DIRECTV®program-
ming package, you can still view over-the-air and
cable TV programs, if you make connections to the
over-the-air and/or cable jacks.
NOTE
A triple LNB multi-satellite dish with a SAT
C LNB is required to receive all DIRECTV®
High-Definition programming, along with
this DIRECTV HD Receiver.
* Sat C may also be connected via a SAT B/SAT C combiner with a 4x4 multi-switch (not supplied by Sony).
27
3. SETUP AND CONNECTIONS
3-5. TV Connection - Analog TV
TV Viewing
1.
Connect the “OUT TO TV” jack on the DIRECTV
®
HD Receiver to the “ANT IN” jack on your TV using a coaxial
RF cable.
2.
Connect the “AUDIO OUT” and “VIDEO OUT” jacks on the DIRECTV HD Receiver to the “A/V IN” jack on your TV
using RCA-type cables.
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
Phone wall jack
L
Analog TV
ANT.IN V R
LNB
Sat B
LNB
Sat C
LNB
Sat A
Dish
5x4 Multi-switch
Output
Antenna
Cable TV
wall jack
28
3-5. TV Connection - HD Monitor (Y/Pb/Pr type)
TV Viewing
1.
Connect the “OUT TO TV” jack on the DIRECTV
®
HD Receiver to the “ANT IN” jack on your TV using a coaxial
RF cable.
2.
Connect the “COMPONENT OUT” jacks on the DIRECTV HD Receiver to the “COMPONENT IN” jacks of your TV
using RCA-type cables. (The “TYPE” switch must be set toward the “Y/Pb/Pr” jacks.)
3.
Connect the L/R “AUDIO OUT” jacks on the DIRECTV HD Receiver to the L/R “AUDIO IN” jacks on your TV using
RCA-type cables.
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
HD-Ready TV
ANT.IN Y Pb PrLR
Phone wall jack
LNB
Sat B
LNB
Sat C
LNB
Sat A
Dish
5x4 Multi-switch
Output
Antenna
Cable TV
wall jack
29
3. SETUP AND CONNECTIONS
3-5. TV Connection - HD Monitor (RGB type)
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
HD-Ready TV
ANT.IN Y Pb PrLR
Phone wall jack
LNB
Sat B
LNB
Sat C
LNB
Sat A
Dish
5x4 Multi-switch
Output
Antenna
Cable TV
wall jack
TV Viewing
1.
Connect the “OUT TO TV” jack on the DIRECTV
®
HD Receiver to the “ANT IN” jack on your TV using a coaxial
RF cable.
2.
Connect the “RGB OUT” jack on the DIRECTV HD Receiver to the “RGB IN” jack of your TV using VGA-type connec-
tor. (The “TYPE” switch must be set toward the “RGB/DVI-HDTV” jacks.)
3.
Connect the L/R “AUDIO OUT” jacks on the DIRECTV HD Receiver to the L/R “AUDIO IN” jacks on your TV using
RCA-type cables.
Note : The RGB OUT jack supports 480p, 720p, and 1080i formats.
30
3-5. TV Connection - HD Monitor (DVI-HDTV type)
TV Viewing
1.
Connect the “OUT TO TV” jack on the DIRECTV
®
HD Receiver to the “ANT IN” jack on your TV using a coaxial
RF cable.
2.
Connect the “DVI-HDTV OUT” jack on the DIRECTV HD Receiver to the “DVI-HDTV IN” jack of your TV using
DVI -type connector. (The “TYPE” switch must be set toward the “RGB/DVI-HDTV” jacks.)
3.
Connect the L/R “AUDIO OUT” jacks on the DIRECTV HD Receiver to the L/R “AUDIO IN” jacks on your TV using
RCA-type cables.
Note: For best access to high-definition programming from DIRECTV, connect the DVI-HDTV output to a
DVI-HDTV input on your high-definition TV or monitor. A DVI-HDTV input is one that is compliant with
EIA-861 and HDCP specifications. Check your TV or monitor’s user manual to find out if the TV or moni-
tor’s DVI input is compliant with these specifications.
(1080i/720p/480p)(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
HD-Ready TV
ANT.IN L R
Phone wall jack
LNB
Sat B
LNB
Sat C
LNB
Sat A
Dish
5x4 Multi-switch
Output
Antenna
Cable TV
wall jack
DVI-HDTV IN
31
3. SETUP AND CONNECTIONS
3-6. VCR Connection
ANT.IN V L R
IN
(1080i/720p/480p)
(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080i
i
/720p/480p/480i
i
)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080i
i
/720p/480p/480i
i
)
PHONE
JACK
VIDEO OUT
Antenna
Cable TV
wall jack
VCR
Phone wall jack
LNB
Sat B
LNB
Sat C
LNB
Sat A
Dish
5x4 Multi-switch
Output
TV Viewing
Refer to Section 3-5, ‘TV Connection’.
VCR Recording
1. Connect the “OUT TO TV” jack on the DIRECTV®HD Receiver to the “ANT IN” jack on your VCR using a
coaxial RF cable.
2. Connect the “AUDIO OUT” and “VIDEO OUT” jacks on the DIRECTV HD Receiver to the “A/V IN” jack on your
VCR using a RCA-type cable. (If your VCR is equipped with an S-Video jack, use the “S-Video” jack)
Note: The OUT TO TV and VIDEO OUT(480i) 1,2 jacks are always available no matter what display format
is selected.
32
3-6. VCR Connection - VCR Controller
Connect the VCR Controller to allow the Timer and Rec feature to automatically operate your VCR. See “VCR Control
Setup “ on page 111 for information about setting up the Digital Satellite Receiver to work with your VCR.
1. Connect the VCR Controller to the VCR CONTROL jack on the DIRECTV®HD Receiver.
2. Place the VCR Controller under and in front of the VCR. The VCR controller must extend just in front of the
infrared sensor of the VCR.
Note: If the infrared sensor is not marked on your VCR, shine a flashlight into the front panel of the VCR to
locate the sensor.
(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
VCR (front view)
VCR (side view) 1/2" to 1"
IR Sensor
VCR Controller
33
3. SETUP AND CONNECTIONS
3-7. Audio Connection - Digital Audio System
Dolby Digital®Connection
1. Connect the “DIGITAL AUDIO OUT” jack on the DIRECTV®HD Receiver to the “SPDIF IN”
jack on your Dolby Digital or Pro Logic®decoder using a digital optical cable.
(A digital optical cable is not supplied.)
(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080ii/720p/480p/480ii)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080ii/720p/480p/480ii)
PHONE
JACK
VIDEO OUT
SPDIF IN
A/V Receiver
34
3-7. Audio connection - Analog Hi-Fi System
Hi-Fi System Connection
1. Connect the Left and Right “AUDIO OUT” jacks of the DIRECTV®HD Receiver to the Left
and Right “INPUT” jacks on your Hi-Fi audio system.
(1080i/720p/480p)
(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080i
i
/720p/480p/480i
i
)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
(1080i
i
/720p/480p/480i
i
)
VIDEO OUT
Analog stereo amplifier
AUDIO IN
Audio cables
35
3. SETUP AND CONNECTIONS
3-8. Remote Control RF Antenna Connection
The DIRECTV
®
HD Receiver can be used with the supplied remote control RF (radio frequency) antenna and
remote control that allow you to control your receiver from outside a cabinet or from another room within your
home.
RF Antenna connection
1.
Plug the remote control RF cable into the RF REMOTE connector on the DIRECTV Receiver rear panel.
2.
Extend the cable and place the antenna in the desired location
To achieve the best operating range from the remote control, position the antenna as high and as far away
from metal objects as possible.
3.
Before using the Remote Control RF Antenna, the Remote Control Setup menu must be set to “RF Type” (see
section 8-24).
Note : Do not place the RF antenna directly on top of the DIRECTV HD Receiver or any other metal object. For
best results, place the RF antenna in a visible location.
(1080i/720p/480p)
(1080i/720p/480p)
RGB OUT
DATA PORT
DVI-HDTV OUT
SATELLITE
IN
TYPE
CABLE IN
ANT IN
OUT TO TV
Y
COMPONENT OUT
(1080i
i
/720p/480p/480i
i
)
Pr
1
L2
R2R1
L1
2
AUDIO OUT
Pb
OPTICAL
DIGITAL
AUDIO
OUT S VIDEO
OUT
VCR
CONTROL
RF
REMOTE
(1080i
i
/720p/480p/480i
i
)
PHONE
JACK
VIDEO OUT
Remote Control RF Antenna
4. FRONT PANEL AND REMOTE CONTROL
36
4-1. Using the Front Panel of the DIRECTV®HD Receiver
Power
Turns the DIRECTV HD Receiver on or off.
Access Card and RESET button
The Access Card is the means by which DIRECTV controls the distribution of its services. The card must be inserted into
the access card slot at all times to enable reception of satellite signals. The RESET button resets the HD Receiver.
Display Window
Shows DIRECTV HD Receiver status : Current output format, interface type, and channel number. Also displays artist
and song information of satellite music-only channels.
Remote Control Sensor
Receives signals from the remote control.
FORMAT
Sets the output resolution to either native, 1080i, 720p, 480p, 480i, variable 1, variable 2, variable 3, or Auto DVI for-
mats. Choose the best display format for your TV. (Refer to Section 2-3, ‘Display Formats’)
INFO
Shows station and program information in the banner shown at the top of the screen. To remove the banner, press the
button again or wait for 10 seconds. You can also change the Audio language, when available, by pressing “FG”.
MENU
Shows the main menu on the screen. You can return to normal viewing by pressing the EXIT button.
GUIDE
Shows the DIRECTV Advanced Program Guide™ screen that shows you a program schedule containing a list of cur-
rent and future programs. You can also access the Advanced Program Guide™ via the main menu (DIRECTV Guide).
You can return to normal viewing by pressing the EXIT button. The Guide is only available with satellite service.
SELECT
If the main menu is displayed, pressing the SELECT button will activate the selected MENU item. If the SELECT
button is pressed while you are in normal viewing, the information banner will be displayed.
EXIT
Clears all on-screen displays and returns to normal viewing from any menu.
Arrow Key (CH +/-)
Allows you to navigate on-screen menus and to adjust the system settings and preferences. Use the arrow keys to
move to a menu option and then use the SELECT button to access it.
1
2
3
4
5
6
7
3
49
1
8
9
10
11
5678
11
2
10
1080i 720p 480p 480i DVI RGB YPBPR
Display format indicator
Standby mode indicator Multi function indicator
Display interface indicator
4. FRONT PANEL AND REMOTE CONTROL
37
4-2. Using the Remote Control
POWER buttons
Turn on and off the DIRECTV®HD Receiver and TV. To operate your
TV, you may need to first set up the remote control (see section 4-
4).
SLEEP button
Sets the TV to turn off automatically after a certain amount of time
(if your TV has a compatible Sleep feature). To operate your TV, you
may need to first set up the remote control (see section 4-4.).
MUTING button
Mutes the TV volume. Press again to restore the volume. To operate
your TV, you may need to first set up the remote control (see page 40.)
FUNCTION buttons
Select the equipment (TV or SAT) that you want to operate. The
indicators light up to show which device the remote control is
operating. To operate your TV, you may need to first set up the
remote control (see page 40.)
TV/VIDEO button
Switches between the various inputs of your TV. To operate your
TV, you may need to first set up the remote control (see page 40.)
PIC MODE button
Switches between the Picture Mode settings of compatible TVs. To
operate your TV, you may need to first set up the remote control
(see page 40.)
0-9 and ENTER buttons
Change channels directly and enter numerical values in on-screen
displays.
• (dot) button
Use with the 0-9 and ENTER buttons to select subchannels
(for example, 2-1, if available).
GUIDE button
Opens the Program Guide.
FAVORITE button
Opens the Favorite List.
INFO button
Opens the program information display for the current program.
M
E
N
U
MUTING
TV
TV/VIDEO
FAVORITE
FLIP OPEN
FREEZE
CODE SET
SIGNAL WIDE
MODE
HELP CC
PREV CH
CHVOL
GUIDE
INFO
ENTER
PIC MODE
FUNCTION
SAT
SLEEP TV POWER
SAT
E
X
I
T
RM-Y822
1
2
3
4
5
1
2
3
4
5
6
7
8
6
7
8
9
10
11
10 9
11
4-2. Using the Remote Control
MENU button
Opens the main Menu.
CH (channel) +/- buttons
Changes channels. When a program guide is open, pressing the CH button
pages through the guide channels.
Joystick (“ ”)
Moving the joystick up, down, left and right moves the highlight in on-
screen displays. Press the joystick to select the highlighted item.
VOL (volume) +/- buttons
Adjust the volume of your TV. To operate your TV, you may need to first set
up the remote control (see section 4-4.)
EXIT button
Closes on-screen displays.
PREV CH button
Changes channels to the previously tuned channel.
FREEZE button
Freezes the current image with digital sources. Pressing a second time
time enlarges the image. Pressing again restores the live video.
WIDE MODE button
Changes the aspect ratio options of the DIRECTV®HD Receiver. When you
view a picture with a wide (16:9) aspect ratio in 480i or 480p format, the
button changes the WIDE MODE options to Letterbox, Cropped or
Squeezed. When you view a picture with a standard (4:3) aspect ratio in
720p or 1080i format, the button changes the WIDE MODE options to
Normal, Wide, Panorama, Zoom or CINE- Zoom. When you view a picture
with a wide (16:9) aspect ratio in 720p or 1080i format, the button tem-
porarily changes the WIDE MODE options to Standard, Expand, or Shrink.
Detailed descriptions of WIDE MODE options are given in section 2-4 or in
the WIDE MODE section of the Preferences menu.
CC (Closed Caption) button
Changes the Digital Caption options and the Closed Caption options of the
DIRECTV HD Receiver. The digital caption mode and the closed caption
mode can also be selected in the Preferences menu. You can also change
the date of the Advanced Program Guide™ by pressing the CC button
when the Guide is displayed.
M
E
N
U
MUTING
TV
TV/VIDEO
FAVORITE
FLIP OPEN
FREEZE
CODE SET
SIGNAL WIDE
MODE
HELP CC
PREV CH
CHVOL
GUIDE
INFO
ENTER
PIC MODE
FUNCTION
SAT
SLEEP TV POWER
SAT
E
X
I
T
RM-Y822
12
13
14
15
16
17
19
20
18
38
15
14
13
12
16
17
18
19
20
4. FRONT PANEL AND REMOTE CONTROL
39
4-2. Using the Remote Control
HELP button
Opens the on-screen Help menu when no other on-screen displays are open.
You can also see the help description of a menu item when that menu is open
by pressing and holding the HELP button.
SIGNAL button
Shows the signal strength of the current digital channel or satellite channel. The
signal strength may be improved by adjusting the over-the-air antenna or satellite
dish antenna as directed by the antenna installation instructions.
CODE SET button
Allows you program the remote control to operate your TV and other
audio/video equipment (see page 40).
POWER button
Turns on and off other devices in your home theater selected with the
AV1/AV2/DVD/AMP switch. To operate other home theater devices, you may
need to first set up the remote control (see page 40).
VCR/DVD control buttons
Operate VCR and DVD basic functions such as play, pause, stop, fast wind,
rewind and record. To operate your VCR or DVD player, you may need to first
set up the remote control (see page 40).
AMP VOL (amplifier volume) +/- buttons
Adjust the volume of your audio receiver. To operate your audio receiver, you
may need to first set up the remote control (see page 40).
DVD navigation and select buttons
Allow you highlight and select items in DVD menus. To operate your DVD play-
er, you may need to first set up the remote control (see page 40).
DVD MENU button
Opens the menu system of the current DVD. To operate your DVD player, you
may need to first set up the remote control (see page 40).
FORMAT button
Changes the video format that is output from the DIRECTV®HD Receiver.
Depending on the type of monitor that the DIRECTV HD Receiver is connected
to, the available formats may include : native, 480i, 480p, 720p, 1080i, variable
1, variable 2, variable 3 and Auto DVI.
AV1/AV2/DVD/AMP switch
Sets the remote to operate other devices in your home theater. To operate
other home theater devices, you may need to first set up the remote control
(see page 40).
M
E
N
U
MUTING
TV
TV/VIDEO
FAVORITE
FLIP OPEN
FAVORITE
FREEZE
CODE SET
SIGNAL WIDE
MODE
HELP CC
PREV CH
CHVOL
GUIDE
INFO
ENTER
PIC MODE
FUNCTION
SAT
SLEEP TV POWER
SAT
MUTING SLEEP TV POWER
POWER
REC
DVD MENU
AMP
VOL
ENTER
FORMAT
SAT
E
X
I
T
RM-Y822
21
22
23
24
25
26
27
28
29
30
21
22
23
24
25
26
27
28
29
30
INSIDE PANEL
40
4-3. Programming the Remote Control
The RM-Y822 remote control is a universal remote control that can be programmed to control
most TV, VCR, DVD and Amp models of the brands that appear on section 4-4.
1. Find the code(s) for the brand of the device you want to operate with this remote
control.
You can find these codes on section 4-4.
2. Press the CODE SET button.
The function indicator begins flashing. If you are setting codes for more than one VCR type,
move the device switch to either the AV1 or AV2 position.
3. Press the 0-9 buttons to input the brand code, then press the ENTER button.
The function indicator goes off, and the remote is set up to operate that device.
4. Test the remote control.
Press the POWER button for that equipment, then press other operation controls such as
the CH+/- buttons. If the device does not respond to the remote control, repeat from step 2
and enter a different brand code in step 3.
Note: See page 112 for instructions on selecting IR or RF type control.
4. FRONT PANEL AND REMOTE CONTROL
41
4-4. Remote Control Codes for Other Components
TV Codes
Manufacturer Code
Sony 101
Admiral (M. Wards) 102, 114, 109
ABC 112
Bell & Howell (M. Wards) 114, 109, 138
Broksonic 103, 112
Craig 122, 123, 120, 121
Croslex 111
Curtis Mathis 103, 119, 123
Daewoo 135, 136, 103
Daytron 116 143
Dynasty 113
Emerson 122, 113, 120, 121, 123, 103, 115
Fisher 125
General Electric 102, 118, 103, 107
Goldstar 103, 113, 112, 130
Hitachi 131, 113, 103, 132
JCPenny 103, 102, 130, 107
JVC 128, 129
KTV 133, 113, 103, 123, 134
Loewe 111
LXI (Sears) 102, 103, 111, 125, 119, 112
Magnavox 111, 112, 113, 107
Mitsubishi/MGA 124, 103, 112
NEC 103, 112
Panasonic 118, 116, 117, 107
Philco 111, 118, 109
Philips 111
Pilot 103
Pioneer 137, 118, 119
Portland 103, 108
Quasar 110, 107
Radio Shack 102, 112, 124, 123
RCA/Proscan 102, 103, 104, 105, 106, 107, 108
Samsung 126, 112, 113, 103
Sanyo 125
Scott 123, 112
Sharp 114, 113, 115
Singnature 2000 (M. Wards) 114, 109
Sylvania 111, 112, 108
Symphonic 123, 139
Technika 109
Toshiba 119, 114
Vidtech 131, 103, 112
Wards 113, 103, 115, 112
Zenith 108, 110
VCR Codes
Manufacturer Code
Sony 301, 302. 303
Aiwa 338
Audio Dynamics 314, 347
Bell & Howell (M. Wards) 330, 343
Broksonic 317, 319
Canon 309, 308
Citizen 332
Curtis Mathis 304, 338, 309
Daewoo 341, 312, 309
DBX 314, 336, 337
Dimensia 304
Emerson 319, 320, 316, 317, 318, 341
Fisher 330, 334, 335, 333
Funai 338
General Electric 329, 304, 309
Go Video 322, 339, 340
Goldstar 332
Hitachi 306, 304, 305, 338
HQ 315
Instant Replay 309, 308
JCPenny 309, 305, 304, 330, 314, 336, 337
JVC 314, 336, 337
Kenwood 314, 336, 332, 337
LXI (Sears) 323, 305, 333, 334, 330, 335, 338
Magnavox 310, 308, 309
Marantz 314, 336, 337
Marta 332
Memorex 309, 335
Minolta 305, 304
Minolta 305, 304
Mitsubishi/MGA 323, 324, 325, 326
Multitech 325, 338, 321
NEC 314, 336, 337
Olympic 309, 308
Optimus 327
Panasonic 308, 309, 306, 307
Pentax 305, 304
Philco 308, 309
Philips 310, 308, 309
Pioneer 308
Quasar 306, 308, 309
RCAProscan 309, 305, 308, 309, 310, 311, 312, 313
42
4-4. Remote Control Codes for Other Components
VCR Codes (Continued)
Manufacturer Code
Realistic 309, 330, 328, 324, 338
Sansui 314
Singer 315
Samsung 322, 313, 321
Sanyo 330, 335
Scott 312, 313, 321, 335, 323, 324, 325, 326
Sharp 327, 325, 328
Shintom 315
Signature 2000 (M. Wards) 336, 327
Sylvania 310, 308, 309, 338
Symphonic 338
Tashiro 332
Tatung 314, 336, 337
Teac 314, 336, 338, 337
Technics 309, 308
Teknika 338, 342
Toshiba 312, 311
Wards 327, 328, 335, 331, 332
Yamaha 330, 314, 336, 336, 337
Zenith 331
DVD Codes
Manufacturer Code
Sony 601, 617, 621
JVC 606
Magnavox 603, 607, 608
Panasonic 604, 609, 610
Philips 603, 607, 611, 612
Pioneer 605, 613, 614
RCA 602
Samsung 615, 616
Toshiba 603, 618
Zenith 619, 620
AMP (Amplfier) Codes
Manufacturer Code
Sony 501, 521
Aiwa 524
Bose 522, 523, 524
B&K 525, 526
Carver 519, 538
Denon 516, 517, 518, 527, 528, 529
Fosgate 532
Haitai 504
Harmon Kardon 519, 530, 531, 532
JVC 506, 507, 508, 533
Kenwood 504, 505, 534, 535, 536
Magnavox 537, 538, 542
Marantz 537, 538, 539, 540, 541, 542
McIntosh 520
NAD 539
Nakamichi 543, 544, 545
Onkyo 512, 513, 546, 547, 548
Panasonic 549, 550, 551, 552
Pioneer 502, 503, 553, 554, 555, 556, 557, 558
Sansui 538
Sharp 534
Technics 509, 510, 511
Yamaha 514, 515, 559, 560, 561
IMPORTANT: Check your TV owner’s manual for the prefered or required video format. The
appropriate format should be set using the FORMAT button on the front panel of the
DIRECTV®HD Receiver. If the correct format is not selected, the on-screen display and video
may not appear correctly or may not appear at all. If an image does not appear, check the
Format setting (see section 2-3).
When you turn on the DIRECTV®HD Receiver for the first time, you will be asked if you want
to set up DIRECTV®programming.
If you have chosen to subscribe to DIRECTV programming (or service), you should initialize
the system according to section 8-7.
If you do not have a dish, you should select “NO”. This means you can receive only off-air
and cable broadcasts (analog & digital).
Although this setup process will be displayed only once, you can change your selection at
any time in the future using the DIRECTV Initial setup menu.
If you have chosen to subscribe to DIRECTV programming, you should contact DIRECTV at 1-
800-DIRECTV (or 1-800-347-3288) and order programming.
When you order programming, you need to know your access card number. To get this num-
ber, press MENU on the remote control, then select SYSTEM on the Menu. Select System
Test on the screen, and you will see the Access Card Identifier. Another way to find the num-
ber is by taking out the access card and referring to the number written on it.
43
5. INITIAL SETUP
6-1. Viewing the Channel Banner
6. BASIC OPERATION
The Channel Banner appears whenever you tune to a new channel or press the INFO button on
the remote control while viewing a program. It displays channel and program information in the
banner shown at the top of the screen. To remove the banner, press INFO again, EXIT or wait
for 10 seconds.
The icons in the Channel Banner represent the status or availability of important features. The
icons will be highlighted when the feature is active or available, as provided by the broadcast-
er and service provider. The information available on the Channel Banner is described below.
Time (Program start and finish(duration)) Channel Logo
Rating Channel Number
High-Definition
Message
Lock
Date
Program Description Input Source
44
Dolby Digital
Closed Caption
Alternate Audio
6. BASIC OPERATION
6-1. Viewing the Channel Banner
Input Source Icon (DIRECTV)
Indicates from which source the current program signal is being received. The DIRECTV®HD Receiver can
receive a signal from ANT, ANT/Digital, CABLE, CABLE/Digital or DIRECTV.
Lock Icon ( )
Indicates that the parental or spending limit lock system is activated (see section 8-19).
Alternate Audio ( )*
DIRECTV and digital channels sometimes provide multiple audio tracks, often in a different language. When
multiple audio tracks are available, the Alternate Audio icon changes its appearance to indicate that you can
select one of those audios by pressing “FG” buttons.
Message Icon ( )
Indicates that your DIRECTV HD Receiver has messages from DIRECTV. The message icon will appear in the
channel banner to indicate that a new message has arrived or there are unread messages in the box.
HD Icon ( )*
Indicates that the current program is broadcast in the HD format.
Doby Digital®Icon ( D )*
Indicates that the currently selected audio track is Dolby Digital®audio and may contain up to 5.1 channels
depending on the broadcast.
CC Icon ( )*
Indicates that the current program contains the closed caption data service.
Channel Logo
Displays the logo of the current satellite channel. If a channel logo is not available, the channel name will
be displayed instead.
Channel Number
Displays the current channel number.
Start and End Time*
Displays the start time and end time of the current program.
Rating*
Displays the rating of the current program.
Date
Displays the current date and time.
Program Description*
Displays a brief description of the current program (if available).
Category*
Displays the genre of the current program.
* Items are based on information provided by the broadcaster or service provider. Occasionally incorrect
information may be provided. For example, a service such as “HD” may be available even if the icon is not
highlighted, or a service such as “Alternate Audio” may not be available even if the Icon is highlighted.
CC
HD
ENGLISH
45
6-2. Accessing Favorite Channels
The favorite list appears on the TV screen when you press the FAVORITE button on the remote
control. It enables you to quickly access up to 50 favorite channels that were chosen in the Edit
Channel section of the Setup menu or directly added in the Favorite guide as described below.
The favorite list consists of the channel logos or channel numbers. If the logo of a certain chan-
nel is not available, the channel number is displayed instead.
You are also able to add or delete the logo of a channel on the favorite list by pressing the
INFO button on the remote. A dialog box will ask what you want to do with the highlighted logo
area: you can replace the highlighted logo area with the current channel, or delete it.
You can easily move the highlight on the favorite list using “DEF G ” on the remote control. The
next page is accessible by using CH +/– button on the remote. You can tune to a favorite chan-
nel by pressing “ ”. Or the EXIT button on the remote will clear the favorite list and take you
back to the current channel.
46
Scroll bar
47
6. BASIC OPERATION
6-3. Freeze Screen
Pressing the FREEZE button freezes the current image. Pressing the FREEZE button again
enlarges the digital video image. The image can then be scanned vertically and horizontally.
Pressing the FREEZE button once again returns the image to live video.
FREEZE Mode Screen
Multi-Freeze Mode Screen
NOTE
The Multi-Freeze mode is only available for
digital channels.
48
6-4. Subscription to DIRECTV®programming and ANT/CABLE-Only operation
The DIRECTV®HD Receiver is designed to receive signals from DIRECTV, ANT and/or CABLE
sources. If you are a DIRECTV customer, you can enjoy programming provided by DIRECTV.
You can also receive the analog and digital over-the-air broadcasts, with the benefit of the
Advanced Program Guide™ which is an integrated electronic program guide. The Advanced
Program Guide™ provides program listings and information on analog and digital channels
from over-the-air local stations as well as DIRECTV channels. You can easily navigate and
tune to hundreds of channels from various signal sources with the Advanced Program
Guide™.
If you don’t subscribe to DIRECTV®programming, however, the function of the DIRECTV HD
Receiver will be limited to receiving signals only from ANT and/or CABLE. You can still enjoy
HD services provided by over-the-air digital broadcast along with the conventional analog
broadcast. Without the DIRECTV service, however, no electronic program guide is available.
49
7-1. About the Advanced Program Guide™
7. ADVANCED PROGRAM GUIDE™
The DIRECTV Advanced Program Guide™ contains schedule and program information for all
DIRECTV®channels. The Advanced Program Guide™ also provides local over-the-air channels
information including both conventional analog and digital channels, if you receive satellite ser-
vice.
Helping you to find a program easily and conveniently, the Advanced Program Guide™ allows you
to view schedule and descriptive program information for the channels. The receiver offers 10
different channel lists: ALL, CUSTOM, FAVORITE and CATEGORY (MOVIES, SPORTS, SPECIALS,
SERIES, NEWS , MY CATEGORY 1 and MY CATEGORY 2). You may edit the CUSTOM and
FAVORITE channel lists to customize and design your favorite channels, respectively. In addition,
you can easily find specific programs by using the CATEGORY search of KEYWORD search func-
tions. An explanation of each channel list is described in Section 7-2.
You can bring up or exit the Advanced Program Guide™ in several ways.
To bring up the Advanced Program Guide™:
- Press the GUIDE button on your remote control.
or
- Press the MENU button on the remote control and select the DIRECTV menu. Several options
will appear. Choose the Guide option (MENU ➝DIRECTV ➝Guide)
To exit the Advanced Program Guide™:
- Press the EXIT button to return to the last channel you were tuned to.
or
- When any currently broadcasted program is highlighted, pressing “ ” will make the guide
screen disappear and tune to that channel.
In the Advanced Program Guide™, you can also show or hide Guide menu .
To show or hide Guide menu:
- Press the GUIDE button on your remote control in the Advanced Program Guide™. The panels
on the left disappear and you can see the Guide menu. The first press shows the Guide menu
at the far left. Pressing the button a second time makes the Guide menu disappear.
50
7-2. Layout of the Advanced Program Guide™ Screen
The on-screen guide maintains ten different channel lists, each of which shows you only those
channels and programs that belong to that channel list. The meaning and generation of each
channel list is described below
Note: When viewing the Program Guide, press the GUIDE button on the remote control to
view the items below in the Guide menu (see section 7-1).
ALL
Shows program listings for all channels to which you may subscribe. The guide shows
DIRECTV®channels that your dish antenna can receive, and over-the-air channels that you
have selected to add into the channel list during the initial setup procedure. Program details
for non-satellite channels may not be available depending on the satellite service provider.
CUSTOM
Shows the program listings that belong to the CUSTOM channel list. You can customize the
CUSTOM channel list by hiding channels from the ALL channel list that you do not wish to view
(see section 8-8).
FAVORITE ( )
Shows program listings only for those channels in the FAVORITE channel list. You can gener-
ate a FAVORITE channel list, which is a short list of channels you tune to most frequently, by
setting a favorite icon to the channels from the menu sequence MENU ➝SETUP ➝
Favorite/Ch. Edit (see section 8-8).
CATEGORY (MOVIES/SPORTS/SPECIALS/SERIES/NEWS)
Lists only Movies/Sports/Specials/Series/News programs from channels in the All chan-
nel list. The DIRECTV®HD Receiver generates the list automatically based on the catego-
ry information of each program identified in the Advanced Program Guide™.
MY CATEGORY 1/ MY CATEGORY 2
Shows only user-defined programs. You can edit MY CATEGORY 1 , MY CATEGORY 2 list
from the menu sequence GUIDE ➝MY CATEGORY ➝EDIT (see section 7-8).
51
7. ADVANCED PROGRAM GUIDE™
7-2. Layout of the Advanced Program Guide™ Screen
The guide screen also provides two search menus:
CATEGORY
Searches for programs that belong to a given category. The DIRECTV HD Receiver first
shows you currently applicable categories and allows you to search for programs in that
category (see section 7-8).
KEYWORD
Searches for programs that have or are related to a specific keyword. You can choose a
keyword for program titles or credit titles (for example, actor/actress, director, writer,
awards, etc.) (see section 7-9).
When accessing an on-screen guide, you will always return to the guide menu, one of
the ten channel lists or one of the two search menus, that you have previously viewed.
NOTE
After first installing satellite service, it may take several
hours bfore all program information is available in the
Advanced Program Guide™.
52
7-3. Moving through the Advanced Program Guide™
The Advanced Program Guide™ is operated based on a simple and straightforward “Highlight
and Select” process.
1. Use “DEF G ” on your remote control to navigate the guide screen.
2. Press “ ” to select or execute the highlighted menu or function.
The on-screen guide shows you program listings for six channels within an one and one half
hour time slot. For example: 6:00-7:30. In order to view a list of future programs or other chan-
nels, you may continuously press “DEF G ” to scroll horizontally or vertically. This may take a
while to reach a specific channel or program, if the channel or program is listed far from the
currently highlighted program. The Advanced Program Guide™ thus offers you shortcuts to min-
imize your effort in navigating channels and time slots.
Line Scrolling
You can reach other time slots or channels that are currently hidden from the screen using the
arrow buttons “DEF G ”. Move horizontally to reach other time slots and move vertically to
reach other channels.
Page Scrolling
You can move through channels faster by scrolling page by page with the CH +/– buttons on the
remote control. Each button stroke scrolls one page up or down.
Date Scrolling
You can scroll time slots day-by-day using the CC button on the remote control. Alternatively,
you can move the highlight to the Date Change Box and change the date to jump to the time slot
of that day. Pressing “FF” button will show you a previous 6 hours guide.
NOTE
Press the GUIDE button to return immediately to the
guide menus, the left-most column of the guide
screen. This is very useful when the highlight is
located far from the current time and you want to
return to the guide menus.
53
7. ADVANCED PROGRAM GUIDE™
7-3. Moving through the Advanced Program Guide™
Direct Jumping
You can quickly jump to a page that contains a specific channel by directly entering a channel
number using the digit buttons “0~9” on the remote control.
Pressing “ ” following the digit button strokes will move to the channel immediately.
Picture In Guide view
You can preview the highlighted channel in the Picture In Guide at left-top window.
You can also quickly jump to a Picture In Guide window by pressing PREV CH button on remote
control. The press moves the highlight to the Picture In Guide at the left-top. Pressing ‘CH +/-’
button take you to another TV channel. Pressing the ‘ ’ button take you to TV viewing.
NOTE
Press the GUIDE button to return immediately to the
guide menus, the left-most column of the guide
screen. This is very useful when the highlight is
located far from the current time and you want to
return to the guide menus.
54
7-4. Selecting a Program
The top region of the guide screen displays the schedule and program information of the cur-
rently highlighted program. You can also see other detailed information about the program by
pressing the INFO button.
When you select the highlighted program by pressing “ ”, what happens or appears next
depends on whether the highlighted program is currently on-air or scheduled in the future, and
whether or not it is a pay per view program.
Current Program / non Pay Per View
If the selected program is a current free-of-charge program, you will directly tune to the program.
Current Program / DIRECTV®Pay Per View
If the selected program is a current pay per view program, you will be asked if you want to pur-
chase this program.
Future Program / non Pay Per View
If the selected program is scheduled in the future and is not a PPV, you will be offered a dialog
box that enables you to reserve this program for watching. If you select Timer option in the Guide
menu, this program is put on the Timer/Record List and you will be reminded by a message at the
topleft corner of the screen 10 seconds before its airing time.
Future Program / DIRECTV®Pay Per View
If the selected program is a pay per view program scheduled in the future, you will also be asked
if you want to purchase this program. Once you confirm the purchase, this program is put on the
Purchase list. You can view the Purchase list from the menu sequence Menu ➝ DIRECTV ➝
Purchase List and cancel any purchase on the list anytime before its airing time.
A continuous connection to a land-based phone line is required to perform this function with your
remote control.
(Note: Pay per view programs can only be purchased within 24 hours of the program times.)
55
7. ADVANCED PROGRAM GUIDE™
7-5. Getting More Program Information
Pressing the INFO button will display available additional information about the highlighted program.
Depending on the broadcaster and service provider, information may include actor and role relationships,
original material, production studio, the date on which the program was first shown, and so on.
To display program details:
1.
Move the highlight to a desired program using “
DEFG
” on the remote control.
2.
Press the INFO button on the remote control to display the available additional information.
3.
To move the highlight to the left menu bar, press “
F
” on remote control. And to return to the additional infor-
mation box, press “
G
”.
4.
To view this TV program, move the highlight to the left menu bar, move the highlight to the “Tune” menu, locat-
ed on the left side of the additional information box, and press “ ”.
56
7-5. Getting More Program Information
5.
If you want to check any other broadcasting schedules for this same program, move the highlight to the
“Showings” menu, located on the left side of the additional information box, and press “ ”.
6.
To return to the previous guide screen, Move the highlight to the “Back” menu, located on the left side of the
additional information box, and press “ ”.
57
7. ADVANCED PROGRAM GUIDE™
7-6. Setting a Timer/Record Event for Future Viewing
If you want to view a program scheduled in the future, you can put that program on the Timer/Record
List so that program will be automatically tuned.
A timer event will automatically tune to the selected channel at the selected time. A Record event will
also turn on the DIRECTV®HD Receiver if it is turned off and will automatically control your VCR to
record the program if the VCR Controller is correctly set up (see sections 3-6 and 8-23).
Timer/Record Events may also be manually set through the menu (see section 8-5).
To schedule a future viewing :
1. Move the highlight to a future program you want to watch using “DEF G ” on the remote control.
2. Press the “ ” button on the remote control to display the available additional information.
3. Pressing “F” will move the highlight to the “Timer” menu, located on the left side of the additional
information box, and press “ ”.
4. A dialog box will appear for your review.
5. Move the highlight to the “OK” option in the dialog box and press “ ” to confirm.
6. The program name will be preceded by the Timer mark. If you want to cancel any reservation, execute
the menu sequence MENU ➝ DIRECTV ➝ Timer/Record List and press “ ” when the highlight is
on the reservation.
NOTE
A reminder message will appear at the top-left
corner of the screen 10 seconds before the
reserved program actually starts. The receiver
will automatically tune to the program if you do
not cancel it.
Pay per view programs can only be purchased
within 24 hours of the program times.
58
7-7. Purchasing DIRECTV®Pay Per View Programs
If you subscribe to DIRECTV®programming, you may preview pay per view movies on channel 200,
the DIRECTV promo channel, to determine if you would like to purchase them.
To purchase Pay Per View (PPV) programs:
1. From the program guide, press INFO button to see the detail information of selected program.
If this program is a pay per view program, “PURCHASE” menu will be appear at left-menu.
Selecting the “PURCHASE” menu will show you the dialog box.
2. Move the highlight to the right to “Buy” in the dialog box and press “ ”.
Another pop-up box will be displayed to verify your purchase.
(A continuous connection to a land based phone line is required to order PPV with your remote
control.)
59
7. ADVANCED PROGRAM GUIDE™
7-8. Searching for Programs by Category
You can search for specific programs by their categories. The category information of each program is provided
by the Advanced Program Guide™ so that you can choose one of them to search for matching programs. You can
also set a search range to One Day or One Week. In the search result, one program may have multiple showings
in different channels and/or in different time slots.
Note : You can also specify an user-defined category using “MY CATEGORY”.
To search programs by Category :
1.
While viewing the Program Guide, press the GUIDE button on the remote control to view the Guide menu.
2.
Highlight the SEARCH in the guide menu. Pressing “ ” will show search sub-menu. Select Category sub-menu and
press “ ”. The Category Search screen consist of two columns: the first column from the left shows the category
names, and the right column lists programs resulting from a category search.
3.
Move the highlight to the category column. If a category has sub-category , the arrow (
G
) mark will be displayed at
the left side. Pressing “ “ will move to the sub-category list. When the highlight is on the selected category name,
pressing “ “ will move the highlight to ‘Search’ button. Pressing “ ” again will start the searching process.
4.
The program resulting from the search will be listed in the right column. The highlight goes to the top program on the
list and its program information will be displayed at the top region of the guide screen. You can see program infor-
mation on each program by moving the highlight using “
DE
”.
5.
In the result column, pressing “
D
” will move the highlight to the top-most tab. You can select one of tab menus
(Program, Channel and Adver. tab ). Selecting Program tab will show searched programs, selecting Channel tab will
show searched Channels and selection Adver. tab will show searched Advertisements.
(Note : If the result list is too big and it is difficult to navigate the list, press FAVORITE button on the remote control.
It will show the ‘Quick Jump’ pop-up box, and is easy to move to some location of the total list.)
6.
If you choose a program and press “ ”, the detailed information screen will be displayed.
60
7-8. Searching for Programs by Category
When you search for programs by category, you can also use an user-defined category in “MY CATEGORY” menu.
You may specify two user-defined categories. One is the “MY CATEGORY1” and the other is the “MY CATEGO-
RY2”. These categories can also be modified in the EDIT menu (in the guide menu->My CATEGORY->EDIT).
Note : You can also specify an user-defined category using “MY CATEGORY”.
To search programs by MY CATEGORY :
1.
While viewing the Program Guide, press the GUIDE button on the remote control to view the Guide menu.
2.
Highlight the MY CATEGORY in the guide menu. Pressing “ ” will show search sub-menu. Select EDIT sub-menu
and press “ ”. The My Category Edit screen consist of two columns: the first column from the left shows the cate-
gory names, and the right column shows the selected category name.
3.
Select the MY CATEGORY1 or MY CATEGORY2 using “
FG
”. And move the highlight to the category column. If a cat-
egory has sub-category , the arrow (
G
) mark will be displayed at the left side. Pressing “ ” will move to the sub-
category list. When the highlight is on the selected category name, pressing “ ” will move the highlight to ‘Save’
button. Pressing “ ” again will modify the “MY CATEGORY1” or the “MY CATEGORY2”.
4.
If you select the “MY CATEGORY1” or the “MY CATEGORY2”, the guide screen will list only user-defined programs in
the All channel list.
61
7-9. Searching for Programs by Keyword
You can also search for programs by keywords which can be found in program titles or credit titles such
as actor/actress name, director name, etc.
To search programs by keyword:
1.
While viewing the Program Guide, press the GUIDE button on the remote control to view the Guide menu.
2.
Highlight the SEARCH in the guide menu. Pressing “ ” will show the search sub-menu. Select the
“Keyword” sub-menu and press “ ”. The Keyword Search screen consists of two columns: the first col-
umn from the left is the key input box, and the right column lists programs resulting from a keyword search.
3. Enter a word using the on-screen keyboard. Highlight a letter first and press “ ” to type it in.
4. While entering a word, the ‘Candidate’ pop-up box will show eight candidate keywords. Press 0-9 but-
ton on the remote control to enter a word quickly.
5. When a word is completed or even when only a partial word is typed in, you may move the highlight
to the Search button with “G”. And press “ ” to begin searching.
6. The programs resulting from the search will be listed in the right column. Program information will be
displayed at the top region of the guide screen. You can see program information on each program by
moving the highlight using “DE”.
7.
In the result column, pressing “D” will move the highlight to the top-most tab. You can select one of tab
menus (Program, Channel and Adver. tab ). Selecting Program tab will show searched programs, selecting
Channel tab will show searched Channels and selecting Adver. tab will show searched Advertisements.
8. If you choose a program and press “ ”, the detail information screen will be displayed.
62
8-1. Accessing the On-screen Menu
8. CUSTOMIZATION
In the menu system, there are several ways to customize the settings provided. To navigate the
menu levels, you will see “ ” or “G” on the right side of the menu label to help you go to the
next level.
To bring up and exit the Menu:
Press the MENU button on the remote control to bring up the menu. A second press of the
MENU button or a press of the EXIT button will take you back to TV viewing.
To go to the next level:
Press “ ” or “G” on the remote control.
To go back to the previous level:
Press “F” or MENU button on the remote control.
63
8-2. The Structure of the On-Screen Menu
DIRECTV
SETUP
AUDIO
PREFERENCE
LOCK
SYSTEM
Guide
Purchase List
Messages
Timer/Record
Timer/Record List
Initial Setup
Auto Program
Manual Ch. Add
Favorite/Ch. Edit
Clock
Out to TV
Hook-up Help
Digital Output
Audio Mode
Audio Language
Dolby Digital
Wide Mode
DTV Caption
DTV Caption Style
Closed Caption
Advanced
Auto Demo
Lock System
Block Channel
Movie Rating
TV Rating – Children
TV Rating – General
Spending Limit
System Info
System Test
Replace Card
VCR Control Setup
Remote Control
64
8-3. Managing Program Purchases
Purchase List
Shows a history of recently purchased programs and displays upcoming DIRECTV®Pay Per View pur-
chases.
Upcoming DIRECTV®Pay Per View purchases can be canceled. You may do this by selecting the pro-
gram. A pop-up screen will ask you if you want to cancel the program.
If you select a past DIRECTV®Pay Per View purchase, you can see each charge of the PPV programs
you purchased and viewed.
To review programs in the Purchase List:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ”on the remote control.
3.
Scroll down to the Purchase List using “
E
”.
4.
Move the highlight to the right with “
G
” to scroll the purchase list.
5.
Press “
F
” to return to the previous level or press the
EXIT
button on the remote control to return to TV
viewing.
NOTE
CAM: Conditional Access Module, usually referred to as the access
card. A removable, electronic subassembly provides conditional
access control of the subscriber terminal.
CAM Slot No: The CAM slot number indicates which slot the purchase
occupied. A satellite service provider customer service representative
may use these slot numbers to help resolve billing issues.
8. CUSTOMIZATION
65
8-4. Checking the Messages
Allows you to view the messages that are sent from DIRECTV. For example, you may receive a mes-
sage requesting your attention to a new service or special program offering.
To check the Messages:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ” on the remote control.
3.
Scroll down to the
Messages
menu using “
E
”.
4.
Move the highlight to the right with “
G
” to select a mail item from the list.
5.
Press “ ” and the full text of the mail will be displayed in the pop-up dialogue box.
6.
Select “Delete” on the pop-up box if you want to delete it.
7.
Press “
F
” to return to the previous level or press the
EXIT
button on the remote control if you want to
return to TV viewing.
NOTE
The Message icon will be displayed in the
Channel Banner only when at least one
unread message is in the mail list.
66
8. CUSTOMIZATION
8-5. Setting a Timer/Record Event
Allows you to set up a timer or record event manually. You can see the event list in the
Timer/Record List menu (DIRECTV ➝ Timer/Record List). You can also set a one time
Timer/Record event in the Guide (see section 7-6).
A Timer event will automatically tune to the selected channel at the selected time. A
Record event will also turn on the DIRECTV®HD Receiver if it is turned off and will auto-
matically control your VCR to record the program if the VCR Controller is correctly set up
(see sections 3-6 and 8-23).
To add a program to the Timer/Record List
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ” on the remote control.
3.
Scroll down to the Timer/Record menu using “
E
”.
4.
Press “
G
” or “ ”. The pop-up dialogue box will be displayed.
5.
Select a Type option , either Timer or Record.
Then select a Channel, Date, Time, Duration and Repeat options.
6.
Pressing “ ” will show the confirm dialogue box. Press “ ” again.
7.
After adding a program, you can check the new item in the Timer/Record List (see next page
‘8-6. Modifying a Timer/Record Event’. )
8.
Press MENU button to return to the previous level or press the EXIT button on the remote
control if you want to return to TV viewing.
67
8-6. Modifying a Timer/Record Event
The Timer/Record List shows the programs you have reserved in the Guide menu or in
the Timer/Record menu. You may cancel any program in the list by selecting the pro-
gram. You may also modify any event in the list that was created in the Timer/Event
menu.
To modify or delete a program in the Timer/Record List:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ”on the remote control.
3.
Scroll down to Timer/Record List using “
E
”.
4.
Move the highlight to the right with “
G
” to select a program from the list.
5.
Press “ ” and the pop-up dialogue box will be displayed.
6.
Select “Delete” in the pop-up box if you want to cancel, then the highlight will return to the
list.
Or
Select “Modify” in the pop-up box if you want to modify type, channel, date, time, duration
and repeat options. The Timer/Record dialogue will appear for modification.
(Note : If the program was reserved in the Guide menu, “Modify” can not be selected.)
7.
Press “
F
” to return to the previous level or press the EXIT button on the remote control if
you want to return to TV viewing.
68
8. CUSTOMIZATION
8-7. Initializing the System
About Initial Setup
The DIRECTV®HD Receiver is capable of receiving three types of signals; ANT, CABLE and
DIRECTV®programming (if you are a DIRECTV®customer). Initial Setup lets you
initialize your system to function properly with your dish antenna.
Setup Wizard
Will provide a guided sequence from dish selection (step1) to channel setup (step 5).
Step 1. Dish Setup
As a first step, you should select one of three dish setup modes ( Manual Selection / Auto
Detection /No Dish ).
Manual Selection allows you to select the correct dish type among three different types avail-
able; Round Dish for Satellite Network A only, Oval Dish for Satellite Networks A and B, or
Oval Dish for Satellite Networks A, B, and C. For advice on selecting a dish that will provide
the services that you desire, contact DIRECTV (1-800-DIRECTV) or your local DIRECTV retail
expert. If you already have a dish, refer to its user’s guide to determine its type. To receive all
available HD programming, you should install and select the Oval dish type (Oval dish (Sat
A,B) or Oval dish (Sat A, B, C)).
The Auto Detection feature will help you select your dish if you are unsure of your dish type.
If you are not a DIRECTV customer and want to view programming only from Antenna/Cable,
then select the No Dish Mode.
69
8-7. Initializing the System
To Select your dish type in Manual Selection:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ” on the remote control.
3.
Scroll down to Initial Setup using “
E
”.
4.
Move the highlight to the right with “
G
” to choose Setup Wizard.
5.
Select the Manual Selection option and press “ ”.
6.
In the Manual Selection screen, select your dish type using “
D
”,”
E
”.
7.
Press “ ” to move to the next step of the initial setup.
Step 2. Dish Positioning
Your Location provides the coordinates of elevation, azimuth, and tilt based upon your zip
code. Elevation is the up/down angle of the dish. Azimuth is the side-to-side direction, while
tilt is the circular rotation of the dish itself around the pointing axis. Full instructions for the
installation of your dish are provided with your satellite dish antenna.
To Select your dish type in Manual Selection:
1.
Enter your zip code using the digit buttons on the remote control.
2.
Press “ ” to show the elevation, azimuth and tilt.
Point your dish properly with the azimuth, elevation and tilt values given.
3.
Press “ ” to move to the next step of the initial setup.
70
8. CUSTOMIZATION
8-7. Initializing the System
Step 3. Signal Strength
Depending on the Dish Type you have selected, the Signal Strength menu shows you up to
three signal strength bars for Satellite Networks A, B, and C, in order to help you adjust the
dish to the correct position with the elevation, azimuth, and tilt values obtained from the Your
Location menu. While the maximum signal strength is 100, there will be no apparent differ-
ence in picture quality between signal strengths of 60 to 85. The higher the signal, the less
likely you are to experience degradation when it rains or snows.
A transponder is a receiver/transmitter on the satellite. It receives signals from DIRECTV and
retransmits them to your dish. The DIRECTV®HD Receiver is capable of displaying the signal
strength of most transponders by using the following method.
To see the signal strength:
1.
Move the highlight to select the desired transponder using “
FG
”.
2.
Set an each value using “
DE
”
3.
Press “ ” to move to the next step of the initial setup.
NOTE
Depending on your location in the United States, certain transponders
may not be available. It is normal for the signal strength level of a few
transponders to be at zero.
71
8-7. Initializing the System
Step 4. Add Local Network
Adds program information for channels available over the air (terrestrial) in a selected local area as
defined by the satellite service provider. You can select two distinct areas by Zip code to view the
channels being broadcast from both areas. This is useful if you live between two major broadcast cen-
ters and are capable of receiving signals from both. After this Channel Setup process, the channel list
of over the air stations will be added to the guide.
To Add Local Network:
1.
If you want to add over the air digital and analog channels to your guide, select “YES”.
Note: If you select “NO”, you don’t need to do the following process.
2.
Press “ ” if your zip code is correct for the primary local channels. The channel search progress will be
shown.
3.
If the zip code is missing or incorrect, select the zip code for your city using “E”and pressing “ ”.
4.
If you want to add secondary local channels from another area, enter a secondary zip code using the digit
buttons on the remote control and press “ ”.
5.
Repeat steps 2 to 4.
6.
Press “ ” to move to the next step of the initial setup.
7.
Press “
F
” to return to the previous level or press the EXIT button on the remote control if you want to
return to TV viewing.
Note : The Add Local Network feature only adds station and program information to the guide. Depending on
your location, such stations may be received by connecting an antenna to the ANT IN jack (see section 3-4).
If off-air digital and analog channel data is selected “YES”, then some local analog (NTSC) and digital
(ATSC) channels may appear in the GUIDE for which reception may be poor or not viewable. To hide these
channels, refer to section 8-8 Managing Channels and section 7-2 Advanced Program Guide™.
72
8. CUSTOMIZATION
8-7. Initializing the System
Step 5. Create Channel list
The Setup wizard will show the summary screen of the setup sequence.
The next page will create the channel list automatically.
After the Setup Wizard process is completed, press the “ ” button on the remote control to
finish the Initial Setup.
73
8-7. Initializing the System
Dish Setup Status
Shows the dish type and up to two distinct areas by Zip code.
To see the dish setup status:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ” on the remote control.
3.
Scroll down to the Initial Setup menu using “
E
”.
4.
Move the highlight to the right with “
G
” to select Dish Setup Status.
5.
Move the highlight to Dish Setup Status and press “ ” . The Dish Information dialogue box will be
displayed.
6.
Press “
F
” to return to the previous menu.
74
8. CUSTOMIZATION
8-7. Initializing the System
Dish Positioning
Provides the coordinates of elevation, azimuth, and tilt based upon your zip code. Elevation is
the up/down angle of the dish. Azimuth is the side-to-side direction, while tilt is the circular
rotation of the dish itself around the pointing axis. Full instructions for the installation of your
dish are provided with your satellite dish antenna.
To enter your location:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ” on the remote control.
3.
Scroll down to Initial Setup using “
E
”.
4.
Move the highlight to the right with “
G
” to select Dish Positioning.
5.
Move the highlight to Dish Position and press “ ” . The positioning dialogue box will be dis-
played.
6.
Enter your zip code using the digit buttons on the remote control.
7.
Press “ ” to show the elevation, azimuth and tilt.
Point your dish properly with the azimuth, elevation and tilt values given.
8.
Press “
F
” to return to the previous menu.
75
8-7. Initializing the System
Signal Strength
Depending on the Dish Type that is selected, the Signal Strength menu shows you up to three sig-
nal strength bars for Satellite Networks A, B, and C, in order to help you adjust the dish to the cor-
rect position with the elevation, azimuth, and tilt values obtained from the Your Location menu.
While the maximum signal strength is 100, there will be no apparent difference in picture quality
between signal strengths of 60 to 85. The higher the signal, the less likely you are to experience
picture quality degradation during adverse weather conditions such as heavy rain or snow.
A transponder is a receiver/transmitter on the satellite. It receives signals from DIRECTV and
retransmits them to your dish. The DIRECTV®HD Receiver is capable of displaying the signal
strength of most transponders by using the following method.
To see the signal strength:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Select the DIRECTV
®
menu by pressing “ ” on the remote control.
3.
Scroll down to Initial Setup menu using “
E
”.
4.
Move the highlight to the right with “
G
” to select Signal Strength.
5.
When the highlight is on the Signal Strength , press “ ” . The signal strength dialogue box will be
displayed.
6.
Move the highlight to select the desired transponder.
7.
Press “
F
” to return to previous menu.
NOTE
Depending on your location in the United States, certain transpon-
ders may not be available. It is normal for the signal strength level of
a few transponders to be at zero.
76
8. CUSTOMIZATION
8-8. Managing Channels
Auto Program (Channel Search)
Automatically finds all channels (both analog and digital) available through the antenna and
cable inputs, and stores all the active channels in the channel list. Inactive or weak channels
may not appear in the list. In that case, add missing channels manually in the Manual Ch. Add
menu. The channel list created here can be seen in the Favorite/Ch. Edit menu.
To scan the channels with the antenna:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Setup
menu by pressing “ ”.
4.
Auto Program will be automatically highlighted.
5.
Move the highlight to the right with “
G
” to display the channel find box.
6.
Select “Start” button and press “ ” and the moving yellow bar will indicate the progress scan-
ning the channels. When the scanning process begins, “Start” will change to “Next”. If you press
“Next”, the scanning of the current signal source will be ignored and the scanning of the next sig-
nal source will proceed.
7.
When the scanning is completed, the scanned result will be displayed.
8.
Press the
EXIT
button on the remote control if you want to return to TV viewing.
77
8-8. Managing Channels
Manual Ch. Add
Manually adds a channel to your channel list without rescanning all the channels again.
Auto Program may not pick up every channel that is available on Air and Cable. Therefore, it
may be necessary for you to add channels manually using this feature.
Note :The Manual Channel Add feature is not available in ANT/CABLE mode. Use the Auto
Program and Favorite/Ch Edit menus to add channels in the ANT/CABLE mode.
To add the channels missed in your channel list:
1.
Press the
MENU
button on the remote control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Setup
menu by pressing “ ”.
4.
Scroll down to
Manual Ch. Add
using “
E
”.
5.
Move the highlight to the right with “
G
” to display the channel add box.
6.
Enter the channel number desired using the digit buttons on the remote control.
7.
Press “ ” and the pop-up box of the result will be displayed.
8.
Press the
EXIT
button on the remote control to return to TV viewing.
Note : Over-the-air local digital channels (ATSC) may have different channel assignments
than their analog (NTSC) broadcast counterparts.
78
8. CUSTOMIZATION
8-8. Managing Channels
Favorite/Ch. Edit
The default channel list is made in the Auto Program menu. Favorite/Ch. Edit allows you to create two other
types of channel lists; custom list and favorite list. A custom list can be created by toggling each channel
on or off with
“”
. Once a channel is highlighted, you will be able to see whether the channel is current-
ly shown or hidden by referring to the small window at the top-left corner of the screen.
To create your own favorite list, with up to 50 favorite channels, press the FAVORITE button on the remote
control when a channel is highlighted.
To edit the channel list:
1.
Press the
MENU
button on the remote control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the Setup menu by pressing “ ”.
4.
Scroll down to Favorite/Ch. Edit using
“E“.
5.
Press “
G
” to display the channel editing screen.
To create a custom list:
1. Use “
DEFG
” to move the highlight on the channel editing menu.
2. Choose “Shown” or “Hidden” by pressing “ ”.
The screen shown at the top left will indicate if the highlighted channel is shown or hidden.
To create a favorite list:
1. Use “
DEFG
” to move the highlight on the channel editing menu.
2. Choose “Favorite” or “No Favorite” using the FAVORITE button on the remote control.
6.
Press the
MENU
button to return to the previous screen or press the
EXIT
button on the remote control to
return to TV viewing.
NOTE
Use the
“
Show All” button to show all the channels.
Use the “Hide All” button to hide all the channels.
79
8-8. Managing Channels
80
8. CUSTOMIZATION
8-9. Setting the Clock
Clock (Auto)
Enables adjustment of the time zone and activation of daylight savings time. Normally, your
clock is set using signals transmitted by DIRECTV.
To set auto clock:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Setup
menu by pressing “ ”.
4.
Scroll down to Clock using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Select your time zone by pressing “
G
” continuously.
7.
Scroll down to Daylight Saving and press “
G
” to switch daylight saving on or off.
8.
If you want to reset the clock, scroll up again to “Auto Set” and press “ ”.
9.
Press the MENU button to return to the previous menu or Press the EXIT button on the remote
control to return to TV viewing.
81
8-9. Setting the Clock
Clock (Manual)
Enables you to set the time manually in the ANT/CABLE Only Operation.
To set manual clock:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Setup
menu by pressing “ ”.
4.
Scroll down to Clock using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Use “
DE
” to move the highlight in the entry boxes.
7.
Enter the number by using the digit buttons on the remote control.
8.
Press “
F
” to return to the previous screen or
press the
EXIT
button on the remote control to return to TV viewing.
82
8. CUSTOMIZATION
8-10. Setting Default Signal Out
Output Channel
If you use the OUT TO TV jack, select channel 3 or 4 to send RF signal from your DIRECTV®
HD Receiver to your TV. Your TV must be tuned to the selected channel to display the pic-
ture.
Loop Through
A signal from CABLE IN or ANT IN jacks is passed through to the OUT TO TV jack when
your HD receiver is in the standby (power off) mode.
To set Out to TV settings of the DIRECTV HD Receiver:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Setup
menu by pressing “ ”.
4.
Scroll down to
Out To TV
using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Select your output channel to Channel 3 or Channel 4 by pressing “
FG
” .
Select your default signal source to Antenna or Cable by pressing “
FG
”.
7.
Press the MENU button to return to the previous menu or press the EXIT button on the
remote control to return to TV viewing.
83
8.11 Hook-up Help
Graphically depicts possible ways to connect the DIRECTV®HD Receiver to your dish antenna and
other components. Since the connection that is best for you depends on the components in your sys-
tem, keep in mind that an alternative connection may also be possible.
To see Hook-up Help:
1.
Press the MENU button on the remote control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Setup
menu by pressing “ ”.
4.
Scroll down to Hook-up Help using “
E
”.
5.
Press “
G
” to display the Hook-up Help diagrams.
Seven possible hook-up connections will be shown.
6.
Scroll up and down the hook-up figure options shown to determine the correct connections for your sys-
tem.
7.
Press the MENU button to return to the previous screen or press the
EXIT
button
on the remote control to return to TV viewing.
84
8. CUSTOMIZATION
8-12. Setting the Audio
Digital Output
If you are using an external audio system that supports Dolby Digital®audio, select Dolby
Digital audio mode. If you are using an external audio system that has a PCM only decoder,
select PCM (Digital). If you are not using an external audio system, select OFF.
An external Digital Output other than Dolby Digital and PCM may create a high pitched
noise and cause damage.
To set the digital audio mode:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Audio
menu by pressing “ ”.
4.
Digital Output will be automatically highlighted.
5.
Move the highlight to the right with “
G
”.
6.
Select one of the three options and press “ ” to return to the previous level.
7.
Press the
EXIT
button on the remote control to return to TV viewing.
85
8-12. Setting the Audio
PCM (Digital)
Pulse Code Modulation (PCM) decoders support L/R stereo only. If selected, audio outputs are
decoded and transmitted to the Digital Output (SPDIF) in PCM mode.
Dolby Digital®
Dolby Digital®audio, formally known as Audio Coding 3rd Generation or 5.1 channel audio, is
a coding technique that provides up to five independent, full frequency response audio chan-
nels and one low frequency bass channel. Dolby Digital signals are available only when pro-
vided by the broadcaster.
NOTE
Refer to section 2-5 to see more
detailed information.
NOTE
Please make sure that your A/V ampli-
fier supports Dolby Digital decoding,
as not all A/V amplifiers support 5.1
decoding.
86
8. CUSTOMIZATION
8-12. Setting the Audio
Audio Mode
Allows you to choose the default audio mode when a program is broadcasting in analog
format.
When you view a program broadcast in mono, you will hear only mono sound, even though
Stereo mode is set. When Second Audio Program “SAP” mode is set, the program’s sec-
ond audio program is broadcast in mono, if provided.
To Set the Analog Audio Mode:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Audio
menu by pressing “ ”.
4.
Scroll down to Audio Mode using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Select one of the three options and press “ ” to return to the previous level.
7.
Press the
EXIT
button on the remote control to return to TV viewing.
87
8-12. Setting the Audio
Audio Language
If available, allows you to hear a program in other languages if the program is broadcast in
digital format. You may select a language while you are viewing a program by selecting an
option on the audio language box in the channel banner and pressing
“
DE
”
repeatedly to
select the desired language.
To set the digital audio language:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Audio
menu by pressing “ ”.
4.
Scroll down to
Audio Language
using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Select one of the eight language options and press “ ” to return to the previous level.
7.
Press the
EXIT
button on the remote control to return to TV viewing.
88
8. CUSTOMIZATION
8-12. Setting the Audio
Dolby Digital®
Allows you to choose Dolby Digital®mode according to which analog audio output port you
use to adjust the adequate audio level. If you connect audio line output to your TV, select ‘Line
Mode’. If you use the OUT TO TV port to connect to your TV, select ‘RF Mode’.
To set the Dolby Digital
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the Audio menu by pressing “ ”.
4.
Scroll down to Dolby Digital using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Select the Line Mode or RF Mode option and press “ ” to return to the previous level.
7.
Press the EXIT button on the remote control to return to TV viewing.
89
8-13. Choosing the Aspect Ratio
Allows you to choose the screen format. When you view a high-definition picture using the video
480i or 480p output format, you can choose Letterbox, Cropped or Squeezed.
When you view a standard-definition picture using the 720p or 1080i output format, you can choose
Normal, Wide, Panorama, Zoom or Cine-Zoom. When you view a high-definition picture using the
720p or 1080i output format, you can temporarily choose Standard, Expand , Shrink.
(Refer to section 2-4 Normal and Wide Format Signals)
Choosing the screen format of your TV:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Preference
menu by pressing “ ”.
4.
Wide Mode will be automatically highlighted.
5.
Move the highlight to the right with “
G
”.
6.
Select one of the options and press “ ” to return to the previous level.
7.
Press the
EXIT
button on the remote control to return to TV viewing.
Note : The WIDE MODE button on the remote control may also be used to toggle through the
available aspect ratio settings of the current content and output format.
90
8. CUSTOMIZATION
8-13. Choosing the Aspect Ratio
Modes for viewing high definition content (16:9) WHEN OUTPUT FORMAT IS 480i
OR 480p MODE :
Letter Box
Use for a picture with an original 16:9 aspect ratio (in a wide format). Letterbox mode will
shrink the picture to fill the screen, with black/gray (or blank) bars appearing at the top and
bottom of the screen.
Cropped
Use for a picture filling the entire screen by cropping (removing) the left and right portions of
the picture.
Squeezed
Use for a full picture filling the entire screen with no black/gray bars. The picture in a 16:9
format will be horizontally adjusted or squeezed to fit the 4:3 ratio monitor. This setting can
also be useful when used with 16:9 aspect ratio monitors or with 4:3 aspect ratio monitors
that have a “16:9 enhancement” feature.
Modes for viewing standard definition content (4:3) WHEN OUTPUT FORMAT IS
720p OR 1080i MODE :
Normal
Use for a picture with an original 4:3 aspect ratio on your 16:9 monitor, with black/gray bars
appearing at the left and right sides.
Wide
Use for a picture adjusted horizontally (in a linear proportion) to fill the entire screen.
Panorama
Use to adjust a picture in a non-linear proportion (more at both sides) to create a spectacular
view.
Zoom
Use when you want to fill the entire screen with no black/gray bars appearing. The image
will be altered both horizontally (stretched) and vertically (cropped). The top and bottom por-
tions of the picture will be cut.
CINE-Zoom
Use to adjust zooming. The picture will be enlarged like the cinema screen.
NOTE
The correct aspect ratio for programming in the 480i and 480p formats from the Video
1/2, S-Video and Component outputs can be automatically set by Sony Hi-Scan™ TVs
when using the TV’s 16:9 Enhanced feature (ID1).
91
8-13. Choosing the Aspect Ratio
Modes for temporarily viewing high definition content (16:9) WHEN OUTPUT FOR-
MAT IS IS 720p OR 1080i MODE :
Standard
Choose when you want to view a picture with no adjustment.
Expand
Choose when you want to view a picture in the 16:9 ratio size. The picture will be horizontal-
ly adjusted or expended to fit 16:9 ratio. Left and right portions of the picture will not be
shown.
Shrink
Choose when you want to view a picture in the 4:3 ratio size. The picture will be horizontally
adjusted or squeezed to fit 4:3 ratio. Black or gray bars will show at the left and right side
Aspect Ratio Summary
Program Format Output Format Available Aspect Ratio
SD(480i/p) 4 x 3 SD(480i/p) 4 x 3 No Adjustment Options
HD(720p/1080i) 16 x 9 SD(480i/p) 4 x 3 Letter Box, Cropped, Squeezed
SD(480i/p) 4 x 3 HD(720p/1080i) 16 x 9 five Aspect Ratio controls
(Normal, Wide, Panorama,
Zoom, Cine-Zoom)
HD(720p/1080i) 16 x 9 HD(720p/1080i) 16 x 9 three temporary Aspect Ratio
controls (Standard, Expand,
Shrink)
NOTE
The aspect ratio setting changes both the high-definition outputs (Component,
RGB/DVI-HDT) and the standard-definition outputs (Video 1/2, S-Video, Out to TV).
When using a VCR or PVR to record programming from the standard definition outputs,
make sure the correct aspect ratio is selected.
92
8. CUSTOMIZATION
8-14. Setting Digital Caption
Allows you to select a mode for displaying Digital Caption Data. In the Digital Caption
Service, Services 1-6 typically represent different Language Services, if available.
Service 1
Service 1 is designated as the Primary Caption Service. This service contains the verbatim,
or near-verbatim captions for the primary language being spoken in the accompanying pro-
gram audio.
Service 2
Service 2 is designated as the Secondary Language Service. This service contains captions
in a secondary language which are translations of the captions in the Primary Caption
Service.
Services 3-6
The other services are not pre-assigned. It is up to the discretion of the individual caption
provider to utilize the remaining service channels.
To set Digital Caption:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the Preference menu by pressing “ ”.
4.
Scroll down to Digital Caption using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Select one of options and and press “ ” to return to the previous level.
7.
Press the EXIT button on the remote control to return to TV viewing.
NOTE
If both digital caption and
closed caption are selected,
only the digital caption will be
selected. The digital caption
can also be selected using the
CC button on the remote con-
trol .
93
8-15. Setting Digital Caption Style
Allows you to customize the caption style to your preference by allowing you to change: Font,
Edge Type, Color, etc.
Note : If the Style setting is “Set By Program” the captions will appear as defined by the pro-
gram provider.
To set DTV Caption Style:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the Preference menu by pressing “ ”.
4.
Scroll down to DTV Caption Style using “
E
”.
5.
Move the highlight to the right with “
G
” to move to the caption style box.
6.
Select each value from Style to Edge Color.
Move the highlight using “
ED
”, and Select a value of each option with “
FG
”.
7. Press the MENU button on the remote control to return to the previous level.
Press the EXIT button on the remote control to return to TV viewing.
94
8. CUSTOMIZATION
8-16. Setting Closed Caption
Allows you to select a mode for displaying analog Closed Caption Data. In the Analog Caption
Service, Captions 1-4 display program’s dialog, and Text 1-4 display for a data service information.
(Note : Closed Captions will appear only when they are provided by the broadcaster.)
Caption1 (CC1)
CC1 is the primary caption service that synchronizes the captioning language with the sound, used
by most broadcasters. The captioning is displayed in the same language as the program’s dialog.
Caption2 (CC2)
CC2 is the special non-synchronous caption service that does not need to be in sync with the sound
and may provide simplified captioning, which is usually delayed.
Caption3 (CC3)
CC3 serves as an alternate captioning service channel. The captioning is often a secondary lan-
guage translation such as French, Spanish, simplified English or displayed at a slower rate.
Caption4 (CC4)
CC4 is another special non-synchronous caption service that does not need to be in sync with the
sound and may provide simplified captioning, usually delayed.
Text1-4
Text1-4 usually display information at the bottom position and is used for a data service, generally
not program related.
To set Closed Caption:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Preference
menu by pressing “ ”.
4.
Scroll down to Closed Caption using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Select one of options and and press “ ” to return to the previous level.
7. Press the EXIT button on the remote control to return to TV viewing.
NOTE
If both digital caption and
closed caption are selected,
only the digital caption will be
selected. The closed caption
can also be selected using the
CC button on the remote con-
trol .
95
8-17. Advanced
Advanced Setup
Allows you to configure special settings such as the background matte color for wide aspect
ratio programming, the channel banner time-out period and the contrast range of DVI output.
To set advanced Setup Menu:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Preference
menu by pressing “ ”.
4.
Scroll down to Advanced using “
E
”.
5.
Press “
G
” to display the Advanced Setup Menu screen.
6.
Select your default background Matte Color which appears with certain aspect ratio settings
with “
FG
”.
And
Select a time-out duration of Information banner between ‘Short’ and ‘Long’.
Or
Select a Banner style of “Small”, “Medium” or “Large” to be displayed when changing channels
or pressing the INFO button.
Or
Select each DVI Level between ‘Standard’ which is recomended for most TVs and ‘Expand’ which
is recommended for most digital monitors.
7.
Press the MENU button on the remote control to return to the previous level.
Press the EXIT button on the remote control to return to TV viewing.
96
8-18. Running Auto Demo
Shows you how to navigate through the on-screen menus of the DIRECTV®HD Receiver.
To run Auto Demo:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Preference
menu by pressing “ ”.
4.
Scroll down to Auto Demo using “
E
”.
5.
Press “
G
” to display the Auto Demo screen.
The screen will run automatically.
6.
Press “
F
” anytime to return to the previous screen or press the
EXIT
button on the
remote control to return to TV viewing.
8. CUSTOMIZATION
97
8-19. Setting Locks
Lock System
Allows you to set up specific channels, ratings and spending limits through blocking schemes.
Also allows you to activate or disable all of the lock schemes previously set up. A password
is required to gain access to this menu if the lock system is activated. You can change the
password by inputting a new password twice. When the system is unlocked, the Channel,
Program Rating and Spending Limits are not effective.
To activate or deactivate the Lock System:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Lock
menu by pressing “ ”.
4.
If unlocked, Lock System will be automatically highlighted, otherwise requires a password.
To lock the system:
1. Move the highlight to the right with “G” in Lock On/Off box.
2. Switch On or Off by using “G” Whenever you switch the lock system on,
you need to enter the password as a reminder.
To set the password:
1. Move the highlight to the Set Password with “E”.
2. Enter the password by using the digit buttons on the remote control.
3. Enter the password again to verify the number.
5.
Press “
F
” to return to the previous screen or
press the
EXIT
button on the remote control to return to TV viewing.
98
8-19. Setting Locks
Block Channel
Blocks any channels that you do not want to view or that you do not want your kids to watch. If you tune
in a blocked channel, a black screen with a pop-up screen will appear. You will have to enter the cor-
rect password to view the channel. Once you turn off the DIRECTV®HD Receiver, Block Channel will
automatically be reactivated.
To block channels:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the Lock menu by pressing “ ”.
4.
Scroll down to Block Channel using “
E
”.
5.
Press “
G
” to display the Block Channel screen.
6.
Use “
DEFG
” to move the highlight in the channel editing screen.
7.
Toggle Blocked or Unblocked by pressing “ ”.
The screen shown at the top left will indicate if the highlighted channel is blocked or unblocked.
8.
Press “
F
” to return to the previous screen or press the EXIT button on the remote control to return to TV
viewing.
NOTE
When you tune to the blocked channel,
the password is required for access.
The Channel Block feature should not
be used as the only parental control.
Since station assignments may change
from time to time, controls such as rat-
ing and spending limits should always
be used as the primary parental control.
Additionally, the Channel Block settings
may be reset if there is an interruption
to the AC power (such as if set is
unplugged or there is a power failure).
8. CUSTOMIZATION
99
8-19. Setting Locks
Movie Rating
Blocks movies according to the movie ratings limit, as defined by the Motion Picture Association of
America, so children cannot view certain movies. You can set the ratings limit by blocking out all the
movies with the ratings above a specified level. Keep in mind that the movie ratings limit applies only to
movies shown on TV, not TV programs such as soap operas.
To block movie programs:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Lock
menu by pressing “ ”.
4.
Scroll down to
Movie Rating
using “
E
”.
5.
Select the level you want using “
DE
” and press “ ” to return to the previous level.
6.
Press the
EXIT
button on the remote control to return to TV viewing.
NOTE
MOVIE/MPAA rating
G: General Audiences
All ages admitted.
PG: Parental Guidance Suggested.
Some material may not be suitable for children.
PG-13: Parents Strongly Cautioned
Some material may not be appropriate for children
under 13.
R: Restricted Under 17 requires accompanying par-
ent or adult guardian.
NC-17: No one 17 and under admitted.
X: No one 17 and under admitted.
NOTE
The Lock feature relies on correct rating information to be provided by broadcaters and
service providers. If broadcast rating information is missing or incorrect, the Lock fea-
ture cannot function as designed.
100
8-19. Setting Locks
TV Rating for Children’s Programs
Keeps children from watching certain children’s TV programs according to the ratings limit as
defined by the TV Parental Guidelines Monitoring Board. This rating applies only to TV programs
for children. Unless you block TV programs intended for mature audiences in the TV Rating –
General menu, your children may view those programs.
To block TV programs:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Lock
menu by pressing “ ”.
4.
Scroll down to TV Rating-Children using “
E
”.
5.
Select Age or Content, if you want to lock a TV program based on age or content.
6.
Select the level you want using “
DE
” and press “ ” to return to the previous level.
7.
Press the
EXIT
button on the remote control to return to TV viewing.
NOTE
TV Rating Children Programs
TV-Y: All Children.
This program is designed to be appropriate for all children.
TV-Y7: Directed to Older Children.
This program is designed for children age 7 and above.
8. CUSTOMIZATION
101
8-19. Setting Locks
TV Rating for General Programs
Blocks TV programs that you and your family do not wish to watch, based on the rating scheme defined
by the TV Parental Guidelines Monitoring Board.
To block TV programs:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Lock
menu by pressing “ ”.
4.
Scroll down to TV Rating-General using “
E
”.
5.
Select Age or Content, if you want to lock a TV program based on age or content.
6.
Select the level you want using “
DE
” and press “ ” to return to the previous level.
7.
Press the
EXIT
button on the remote control to return to TV viewing.
NOTE
TV Rating for General Programs
TV-G: General Audience.
Most parents would find this program suitable for all ages.
TV-PG: Parental Guidance Suggested.
This program contains material that parents may find unsuit-
able for younger children.
TV-14: Parents Strongly Cautioned.
This program contains some material that many parents would
find unsuitable for children under 14 years of age.
TV-MA: Mature Audience Only.
This program is specifically designed to be viewed by adults
and therefore may be unsuitable for children under 17.
102
8-19. Setting Locks
Spending Limit
Sets the spending limit of each PPV program. After a spending limit is set and the system is
locked, you must enter the password to purchase a PPV program that costs more than your
spending limit allows. The system will temporarily unlock the limit you previously set. Once
the receiver is turned off and then turned back on, the lock will be reactivated.
To set the spending limit of each PPV program:
1.
Press the
MENU
button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the
Lock
menu by pressing “ ”.
4.
Scroll down to
Spending Limit
using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
Enter the maximum amount of money to be spent on each PPV program.
7.
Press “ ” to return to the previous level.
8.
Press the
EXIT
button on the remote control to return to TV viewing.
8. CUSTOMIZATION
103
8-20. Getting the System Information
General Info
Shows you general information of your DIRECTV®HD Receiver.
To view General information in the HD receiver:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
System Info will be automatically highlighted.
5.
Move the highlight to the right with “
G
” to display the information option box.
6.
General Info will be automatically highlighted.
7.
Press “ ” and the general information dialogue box will be displayed.
8.
Press the EXIT button on the remote control to return to TV viewing.
104
8-20. Getting the System Information
Feature List
When in Satellite mode, allows you to see which major features are available for your
DIRECTV®HD Receiver.
To view Feature list in the HD receiver:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
System Info will be automatically highlighted.
5.
Move the highlight to the right with “
G
” to display the information option box.
6.
Scroll down using “
E
” on the remote control to select Feature List.
7.
Press “ ” and the pop-up dialogue box will be displayed.
8.
You can see the feature list on the right side of the menu.
9.
Press the EXIT button on the remote control to return to TV viewing.
8. CUSTOMIZATION
105
8-20. Getting the System Information
Tuner List
When in Satellite mode, shows you what kind of tuners are built in your DIRECTV®HD
Receiver.
To view Tuner list in the your HD receiver:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
System Info will be automatically highlighted.
5.
Move the highlight to the right with “
G
” to display the information option box.
6.
Scroll down using “
E
” on the remote control to select Tuner List.
7.
Press “ ” and the pop-up dialogue box will be displayed.
8.
You can see the Tuner list on the right side of the menu.
9.
Press the EXIT button on the remote control to return to TV viewing.
106
8-20. Getting the System Information
System Upgrade
When in Satellite mode, shows you the current software version. If there is a software upgrade
planned, you will be notified by a pop-up box on your TV screen and the pop-up box will ask you
if you want to upgrade your system.
To upgrade the software in the DIRECTV®HD Receiver:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
System Info will be automatically highlighted.
5.
Move the highlight to the right with “
G
” to display the information option box.
6.
Scroll down to System Upgrade using “
E
”.
7.
Press “ ” , then you can see the current software version on the right side of the menu.
The next version will be seen if DIRECTV plans to upgrade the software.
8. Press the EXIT button on the remote control to return to TV viewing.
The DIRECTV HD Receiver is able to receive upgrades or modifications to some of its features and func-
tions. These modifications will automatically be made, usually at times when the receiver would like-
ly be turned off. If your receiver is on when an upgrade or modification is sent, you may experience a
disruption in reception for a minute or two. Your reception should return to normal after the modifica-
tion is complete. Your receiver must be plugged in to receive any upgrades. Please consult the Upgrade
Menu to find a schedule of upgrades or modifications planned by DIRECTV.
(Note: Do not unplug your receiver while an upgrade is in progress. )
8. CUSTOMIZATION
107
8-21. Testing the System
Basic Test
When in Satellite mode, diagnoses essential system components of your HD receiver. Once
the Basic System Test is done, your HD receiver’s status will be displayed. If any problems are
detected, a short message will be displayed.
To test basic items in DIRECTV HD Receiver :
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
Scroll down to System Test using “
E
”.
5.
Move the highlight to the right with “
G
”.
6.
“Basic Test” Info will be automatically highlighted.
7.
Press “ ” and the pop-up dialogue box will be displayed.
8.
Press “ ” to activate the System Basic test.
It will run automatically from DIRECTV Tuner to Phone Connection and if there is any problem in
your system, the pop-up box will be displayed.
9.
Press the EXIT button on the remote control to return to TV viewing.
108
8-21. Testing the System
Satellite Dish Antenna (Outdoor Unit) Test
When in Satellite mode, diagnoses the Satellite Dish Antenna (LNB and Satellite Antenna) con-
nected to the HD receiver. Once the Satellite Dish Antenna (Outdoor Unit) Test is done, Satellite sig-
nal status will be displayed. If any problems are detected, a short message will be displayed.
To test the Outdoor Unit :
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
F
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
Scroll down to System Test using “
E
”.
5.
Move the highlight to the right with “
G
” to display the system test option box.
6.
Scroll down to Outdoor Unit Test using “
E
” on the remote control.
7.
Press “ ” and the pop-up dialogue box will be displayed.
8.
Press “ ” to activate the system outdoor unit test.
It will run automatically and if there is any problem in your system, the pop-up box will be displayed.
9.
Press the EXIT button on the remote control to return to TV viewing.
8. CUSTOMIZATION
109
8-21. Testing the System
Transponder Test
When in Satellite mode, diagnoses all transponder signals of each Satellite. Once the
Transponder Test is done, all transponder signal status of the selected Satellite will be dis-
played.
To test the Transponder:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
Scroll down to System Test using “
E
”.
5.
Move the highlight to the right with “
G
” to display the system test option box.
6.
Scroll down to Transponder Test using “
E
” on the remote control.
7.
Press “ ” and the pop-up dialogue box will be displayed.
8.
Select one of SAT A/SAT B/SAT C with “
FG
”.
9.
Move the highlight to the Start Button and press “ ” to activate the system transponder test.
It will run automatically and if there is any problem in your system, the pop-up box will be dis-
played.
10.
Press MENU button to return to the previous level or press the EXIT button on the remote con-
trol to return to TV viewing.
Note : Depending on your location in the United States, certain transponders may not be
available. It is normal for the signal strength level of a few transponders to be at zero.
110
DIRECTV may issue you a replacement access card periodically, if you are a DIRECTV customer when in
Satellite mode. This menu enables you to transfer information, such as the record of your purchases,
from the old card onto a new one. The access card fits into the slot on the front panel of the DIRECTV®
HD Receiver.
Once you proceed past “Read the old card”, replace card cannot be cancelled.
To replace the card :
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
Scroll down to Replace Card using “
E
”.
5.
Pressing “ ”. Replace Card Wizard will be displayed.
6.
If you want the process to proceed, follow the instructions in the Replace Card Wizard.
7.
Press the EXIT button on the remote control to return to TV viewing.
8-22. Replace Card
8. CUSTOMIZATION
111
Allows you to set up the DIRECTV®HD Receiver to control with your VCR for automatic recording when
used with the Record feature (see section 8-5).
To set up the VCR Control:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
Scroll down to VCR Control Setup using “
E
”.
5.
Pressing “ ”. VCR Control Setup Wizard will be displayed.
6.
If you want the process to proceed, follow the instructions in the VCR Control Setup Wizard.
7.
Press the EXIT button on the remote control to return to TV viewing.
8-23. VCR Control Setup
8. CUSTOMIZATION
112
8-24. Remote Control Setup
Your DIRECTV®HD Receiver’s remote control can send signals to the HD Receiver in two ways.
Standard IR (Infrared) control allows the Remote Control to send signals to the HD Receiver
within a line of sight. RF (Radio Frequency) to send signals from outside a cabinet or even from
another room within your home. The Remote Control RF Antenna must be connected to use the
RF Remote feature (see section 3-8).
You can also choose to assign one of two remote ID’s for IR Control or one of sixteen remote
ID’s for RF Control. This can be useful if you have more than one Sony satellite receiver in your
home.
To choose the Remote Control type:
1.
Press the MENU button on the Remote Control to display the on-screen menu.
2.
Scroll down using “
E
” on the remote control.
3.
Select the System menu by pressing “ ”.
4.
Scroll down to Remote Control using “
E
”.
5.
Pressing “ ”. Remote Control Setup Wizard will be displayed.
6.
Choose the IR type or RF type using “
DE
”.
If you want the process to proceed, follow the instructions in Remote Control Setup Wizard.
7.
Press the EXIT button on the remote control to return to TV viewing.
8. CUSTOMIZATION
113
9-1. Help
9. Help
The Help feature is designed to let you understand each function of the Menu and Advanced
Program Guide™ in an easy and convenient way. When you navigate through the Menu and
the Advanced Program Guide™, press and hold the
“
HELP
”
button on your remote control if
you want information about the highlighted item. The information will be displayed on the
right side of the TV screen.
Simply press and hold the
“
HELP
”
button to see the helpful information.
NOTE
Pressing the “HELP” button on your remote control
independently will activate the overall Help feature.
However, when the MENU or the Advanced Program
Guide™ is already displayed, pressing the “HELP”
button will activate the specific Help feature.
114
9. Help
9-1. Help
The Help is an on-line version of this Operating Guide. You can review many features of the
DIRECTV®HD Receiver by navigating through a simple structure. It contains a brief overview of
the DIRECTV HD Receiver, the use and programming of the remote control, a functional expla-
nation of the front and back panel, and an instructive note about the Menu and the Advanced
Program Guide™.
The see the Help feature:
1.
Press the “
HELP
” button on the remote control to display the Help screen.
2.
Scroll up and down to select Help menu items using “
E
” on the remote control.
3.
Move the highlight using “
DEF G
”.
The explanations of the highlighted item will be displayed on the right side or at the bottom of the
screen.
4.
Press the
EXIT
button on the remote control if you want to return to TV viewing.
115
PRODUCT SPECIFICATIONS
Television System NTSC, Analog American Standard (480i)
ATSC, Digital TV standard (1080i, 720p, 480p, 480i)
DIRECTV
Channel Coverage
Digital TV 1-69
VHF 2-13
UHF 14-69
Unscrambled Analog CATV 1-125
Unscrambled Digital CATV 1-135
DIRECTV variable
Inputs/Output
ATSC/NTSC RF Inputs Antenna (1), Cable TV (1) (ATSC 8-VSB and QAM over CATV or Terrestrial)
RF Output Out To TV (1) (selectable Channel 3 or 4)
DIRECTV RF Input Satellite In (1)
DVI-HDTV Output DVI-HDTV Out (1), DVI-D Single Link connector
1080i, 720p, 480p, 480i digital RGB
EIA-861 Compliant, HDCP 1.0 Compliant
RGB Output 15-pin Connector (1)
1080i, 720p, 480p RGB
Component Video Output Component Out (1), Phono Jack connector
1080i, 720p, 480p, 480i YPbPr
S-Video Output S-Video Out (1), 4-pin Mini-DIN
480i Y/C
Video Output Video Out (2), Phono Jack connector
480i Composite NTSC
Digital Audio Optical (selectable Dolby Digital®audio or PCM output)
Analog Audio Audio Out (2) (Fixed Output Level)
Access Card Smart Card (Slot on the front)
Data Port 9-pin Serial Port (1)
VCR Control IR blaster (1)
RF Remote RF Remote Controller (1)
Supplied Accessories
Remote Control RM-Y822
Batteries AA type Batteries (2)
Cables DVI-D Single Link Cable (1)
Component Cable (1)
S-Video Cable (1)
Audio/Video Cable (1)
RF Cable (1)
Telephone Cable (1)
VCR Controller (1)
Remote Control RF Antenna (1)
Dimension 430mm (W) x 69mm (H) x 326mm (D) (Excluding Feet)
Mass 3.84kg
Power Requirements AC 120V, 60Hz
Power Consumption 40W (Maximum)
20W (Standby: Single LNB)
Design and specifications are subject to change without notice.
116
TROUBLESHOOTING
Sony and DIRECTV are dedicated to providing you with quality support and customer service. If you have questions or
difficulties that you cannot resolve using the tips in this troubleshooting section, consult your dealer or call DIRECTV at
1-800-DIRECTV (1-800-347-3288) regarding DIRECTV
®
Service problems and contact the Sony Satellite System
Information Center at 1-800-838-7669 regarding problems with your DIRECTV
®
HD Receiver.
SYMPTOMS SOLUTIONS
No power.
No signal.
No picture.
- Macroblocking in picture
- No Signal OSD/VFD
- Scrambled Channel
- Searching for satellite signal.
Please standby OSD/VFD
- Is the AC power cord plugged in?
- Check your antenna input or location.
- Check your cable input.
- Check your satellite input.
- Make sure that the correct format is selected.
- Press the FORMAT button on the front panel to change formats. (see
section 4-1)
- Make sure that the right component type is selected.
If the DIRECTV
®
HD Receiver is connected to your monitor or TV via
Y/Pb/Pr port on the back panel, the “TYPE” switch must be flipped to the
left. Otherwise, you may not be able to see a picture. (see section 3-5)
If the DIRECTV HD Receiver is connected to your monitor or TV via
RGB/DVI-HDTV port on the back panel, the “TYPE” switch must be
flipped to the right. Otherwise, you may not be able to see a picture. (see
section 3-5).
- Make sure the Initial Setup process has been performed (see section
8-7).
- Select the Auto Channel Scan or Manual Channel Add functions if you
have not already done so (see section 8-8).
- If you are only receiving a few satellite channels, you may need to call
your service provider to have your programming activated.
- Check to make sure all the cables are installed correctly and that the
proper source is selected on your TV. For example, channel 3 or 4, 480i.
- The satellite or digital TV signal strength may be low. Check the signal
strength and adjust the satellite dish or TV antenna as recommended by
the dish or antenna installation instructions (see section 8-7).
- Make sure the broadcaster or service provider is supplying programming
on the selected channel use the SIGNAL button to check for digital video
signals (see section 4-2).
- You may be trying to access a pay per view program. Follow the
on-screen instructions to order the program.
- Due to copyright restrictions, you may not be able to view some high def-
inition programs in the high definition format.
- Make sure the Access Card is inserted correctly.
- For more information about connections, please refer to Section 3 of this
manual.
- No further changes.
117
SYMPTOMS SOLUTIONS
The Program Guide shows channels
I don’t receive.
Cannot receive high-definition chan-
nels.
Normal picture but no sound.
Picture is distorted.
Available channels are missing.
A previously available channel is no
longer available.
4:3 Aspect ratio cannot be selected.
- Contact your service provider to subscribe to all available channels.
- Adjust your antenna or satellite dish to receive all available channels.
(see section 3-4)
- Use the Custom Guide feature to select channels that you receive. (see
section 7-2)
- Whenever you access the GUIDE, make sure you select the CUSTOM
guide (see 7-2) to show only channels not HIDDEN (see 8-8). In order to
ensure that you do not miss any new channel additions or special pro-
gramming, when entering the GUIDE, it will default to ALL.
- Make sure that a multi-sat dish is used for HD satellite service (see sec-
tion 3-4).
- Make sure there is a good signal strength on available satellites (see
section 8-7).
- Check volume levels.
- Make sure the TV is not muted.
- Check that the DIRECTV
®
HD Receiver is connected properly.
- Make sure the proper format is selected. (see section 2-3)
- Make sure the proper aspect ratio is selected. (see section 2-4)
- Make sure the video output is connected to the TV. (see section 3-5)
- Adjust the aspect ratio setting of your TV or monitor if available.
- If you are a DIRECTV customer, you can add a channel by running the
“Manual Ch. Add” from the SETUP menu or find all available channels by
running the “Auto Program” in the SETUP menu. (see section 8-8)
- Otherwise, if the DIRECTV Receiver is in the ANT/CABLE mode, you can
find available channels by running the “Auto Program” in the SETUP
menu. (see section 8-8)
- Digital channels can be dynamically changed by broadcasters and service
providers. A channel that may have been available in the past may have
been moved or deleted. Consult your local broadcaster or service
provider.
- Aspect ratio depends on both the incoming program format and the FOR-
MAT setting. Once the button for the format is set to a standard defini-
tion (480i/480p) and the incoming program is standard definition, the
aspect ratio can not be adjusted and a warning message will appear on
the screen. (see section 8-13)
118
SYMPTOMS SOLUTIONS
Aspect Ratio setting is re-set after
the channel is changed.
The remote control is not responding.
The timer does not work.
You forget your password.
If a white bar is shown at the top
position on the display device
Weak Sound
Conflicting digital channel numbers.
Cannot tune to a station
Additional problems.
Channel content does not match
that shown displayed in the GUIDE
or INFO banner.
- When the Format is set to a high-definition setting (720p/1080i) and the
incoming program is in high-definition, the Aspect Ratio setting can only
be adjusted temporarily.
- Make sure the batteries are fresh and installed properly.
- Point the remote control unit at the remote control sensor.
- Check if the correct function (TV or SAT) on the remote control is
selected.
- Make sure the correct Remote Control type and code are set for both the
remote and receiver. (see section 8-24)
- Make sure the clock is set properly. (see section 8-9)
- If you subscribe to satellite service, contact your service provider to
arrange for the password to be re-set
- If you do not subscribe to satellite service and the DIRECTV HD Receiver
is in the ANT/CABLE mode, enter the master password “7777”.
- Use the Component Output.
- Adjust the scan range of your display device.
- If connected to a TV using the “OUT TO TV” jack, set RF mode of “Dolby
Digital” menu. (MENU
➝
Audio
➝
Dolby Digital)
- Press the SIGNAL button on the remote control, the physical channel
number will be shown.
- Press the INFO button on the remote control, the logical channel number
will be shown in the channel banner.
- If you receive more than one station with the same channel number
(such as channel 8 from satellite and channel 8 from over-the-air) enter-
ing “8” the first time will tune to satellite channel 8, entering “8” a sec-
ond time will tune to analog channel 8, and so on.
- Press the RESET button (see section 4-1).
- Please confirm that the Dish mode is set to the correct type using AUTO
DETECT to confirm dish type (see section 8-7)
(this is the “BBCAmerica” wrong channel effect seen when Manual
Selection default of Triple Sat is used with a dual sat dish, etc.)
- Please confirm that the Dish mode is set to the correct type using Auto
Detection for Dish type (see 8-7) or confirm your dish connections
(see 3-4).
TROUBLESHOOTING
119
SYMPTOMS SOLUTIONS
Closed captions are not displayed.
Two sets of overlapping captions
appear.
Closed captions are not shown
using my custom styles.
Cannot receive audio with 5.1 chan-
nels.
Control of this product using
PVR/DVR Hard Disk Recorder some-
times misses channels, when tun-
ing.
Programming which appears to
exceed my Lock settings is not
blocked.
- Most recent TVs also include captioning capability, which you may inde-
pendently set (see TV manual for details). If the captions are ON for both
TV and this product, you may see overlapping captions. In this case,
please turn off captioning on the TV or this product (see 8-14).
- When using the DVI-HDTV or RGB connections, captioning must be dis-
played using this product (see 8-14). This may also be necessary, when
FORMAT is set to modes other than 480i for YPbPr connection.
- Depending on broadcast provider, different types of captioning may be
available. According to your preferences, you will need to set your
Caption settings for Analog and Digital modes.
- By selecting both Analog on (for instance, CC1) and Digital CC on (for
instance Service1) by pressing the CC button on the remote or by access-
ing settings outlined in 8-14 to 8-16), both types captioning will be dis-
played automatically, based on broadcast provider information.
- Custom styles (described in 8-15) only are applied to some digital broad-
casts with Digital Captions. Depending on the broadcast, you may need
to set the Analog captions to OFF to view the Digital Captions.
- Dolby Digital 5.1 audio requires the use of the digital audio output con-
nection with a compatible Dolby Digital A/V Receiver (see 3-7).
- Confirm that you have set the Audio > Digital Output setting to Dolby
Digital mode (see 8-12).
- Availability of 5.1 audio will depend on the broadcast provider and is not
available for analog broadcast sources. Although Dolby Digital can sup-
port up to 5.1 channels, some broadcasts may only be available in
stereo.
- Confirm that the IR Controller is located near the Remote Control Sensor
(see 4-1 item 4) in accordance with your DVR Manual.
- For the most reliable control, connect to your PVR/DVR using the Data
Port connection (see 3-2).
- Please confirm Lock has been enabled with your preferred limits
(see 8-19).
- Depending on broadcast provider, not all programming may contain rat-
ing information necessary to block certain programming.
TROUBLESHOOTING
120
Limited Warranty
Digital Satellite Receivers
SONY ELECTRONICS INC. (“SONY”) warrants this Product
against defects in material or workmanship as follows:
1. Labor: For a period of 90 days from the original date of
purchase, if the Products is determined to be defective,
SONY will repair or replace the Product at no charge. After
this 90 day period, you must pay for all labor charges.
2. Parts: For a period of one year from the original date of
purchase, SONY will supply, at no charge, new or rebuilt
replacements in exchange for defective parts. Any replace-
ments will be warranted for the longer of the remainder of
the original warranty period or 90 days from the installa-
tion of the parts by a Sony authorized DIRECTV®System
installer or facility.
To obtain warranty service:
- If the Product was installed by a SONY authorized
DIRECTV System installer, contact that installer for
instructions.
- If the Product was not installed by a SONY authorized
DIRECTV System installer, you must take the Product or
deliver the Product in either its original packaging or
packaging affording an equal degree of protection (with
freight prepaid), to a SONY authorized DIRECTV
System service facility. To locate the closest such facility,
please call the telephone number listed below.
This warranty does not cover customer instruction, installation,
set up adjustments or signal reception problems. This warranty
does not cover cosmetic damage or damage due to acts of God,
accident, misuse, abuse, negligence, commercial use, or modi-
fication of, or to any part of the Product. This warranty does
not cover improper installation (if not installed by a SONY
authorized DIRECTV System installer), loss of use of the
Product malfunction. This warranty does not cover damage due
to improper operation or maintenance, connection to improper
voltage supply, or attempted repair by anyone other than a
facility authorized by SONY to service the Product. This war-
ranty does not cover Products sold AS IS or WITH ALL
FAULTS. This warranty is valid only in the United States.
Proof of purchase in the form of a bill of sale or receipted
invoice which is evidence that the Product is within the
Warranty period must be presented to obtain warranty service.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER. SONY SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY
ON THIS PRODUCT. IN NO EVENT SHALL SONY BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES WHATSOEVER ARISING OUT OF THE USE
OR INABILITY TO USE THE PRODUCT. UNDER NO CIR-
CUMSTANCES SHALL SONY’S LIABILITY, IF ANY,
EXCEED THE PURCHASE PRICE PAID FOR THE PROD-
UCT. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PUR-
POSE ON THIS PRODUCT IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.
This warranty is invalid if the factory applied serial number has
been altered or removed from the Product. Some states do not
allow the exclusion or limitation of incidental or consequential
damages, or allow limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not apply to
you. In addition, if you enter into a service contract with the
SONY Partnership within 90 days of the date of sale, the limi-
tation on how long an implied warranty lasts does not apply to
you. This warranty gives you specific legal rights, and you may
have other right which vary from state to state.
For your convenience, SONY ELECTRONICS INC. has
established telephone numbers for frequently asked questions:
For assistance with installation, contact the dealer from whom
you purchased your Digital Satellite Receiver.
For product information or operation, for service assistance or
for resolution of a service problem, call:
SONY SATELLITE SYSTEM INFORMATION CENTER
1-800-838-SONY (7669)
For an accessory or part not available from your authorized
dealer, call:
1-800-488-SONY (7669)
121
Software License Agreement
License and Restrictions
Sony Electronics Inc.(“Sony”) grants User a license to Use one
copy of the software which is provided to you as part of this
Sony product(“software”). “Use”means storing, loading,
installing, executing or displaying the Software. Use may not
copy, modify the Software or disable any licensing or control
features of the Software. No portion of the Software may be
reproduced in any form, or by any means, without prior written
permission from Sony. User is not permitted to modify, distrib-
ute, publish, transmit or create derivative works of any
Software included for any public or commercial purposes. In
consideration of this authorization, User agrees that any copy
of this Software which User makes shall retain all copyright
and other proprietary notices in the same form and manner as
on the original. Except as specified above, nothing contained
herein shall be construed as conferring by implication, estoppel
or otherwise any license or right under any patent, trademark or
copyright of Sony, its affiliates or any third party licensor.
User may not in any way sell, lease, rent, license, sublicense or
otherwise distribute the Software. The software may only be
accessed by the functionality of the Sony product in which the
Software is incorporated by Sony (the “Product(s)”), and a
User shall not intentionally make the Software directly accessi-
ble to others or to hardware other than the Products, or other-
wise expose an API. Nothing in this Agreement grants User
any rights, license or interest with respect to source code of the
Software. User shall not modify, translate, reverse engineer,
decompile or disassemble the Software or any part thereof or
otherwise attempt to derive source code or create derivative
works therefrom, and shall not authorize any third party to do
any of the foregoing provide to User updates and other support
services for the licensed Software. All updates provided to User
shall constitute licensed Software under this License, and such
updates shall be governed by the terms hereof.
Intellectual Property
The Software is owned and copyrighted by Sony, its affiliates
or its third party licensors. User’s license confers no title or
ownership in the Software and is not a sale of any rights in the
Software. Sony’s affiliates and/or third party suppliers may
protect their rights directly in the event of any User’s violation
of this Agreement. The trademarks, tradenames, Product
designation, logos and service marks (“Marks”) displayed with
this Software are the property of Sony, its affiliates or third
party licensors, and User shall acquire no rights of any kind in
or to any Mark under which the Software and/ or Products are
marketed. User is not permitted to use these Marks without the
prior written consent of Sony, its affiliates or the applicable
third party licensor which may own the Mark.
“Sony” is a registered trademark of Sony Corporation. User
agrees not to remove, alter or destroy any patent, trademark or
copyright markings or notices placed upon or contained within
the Software, User Manuals or documentation. User further
agrees to insert and maintain with the Software and any docu-
mentation a copyright notice in User’s name.
Termination
User’s license will automatically terminate upon any transfer of
the Product. Upon transfer, User must deliver the software,
including any copies and related documentation, to the transfer-
ee. The transferee must accept these License Terms as a condi-
tion to the transfer. Otherwise, Sony does not authorize the
transfer and the User and transferee will be in violation of this
Agreement should the transferee use the Product. This license
will automatically terminate upon User’s failure to comply
with any of these License Terms. Upon termination, User must
stop using the Product and immediately destroy the Software,
together with all copies, adaptations and merged portions in
any form and/ or return it to Sony.
Export Requirements and U.S. Government
Restricted Rights
User may not export or re-export the Software or any copy or
adaptation in violation of any applicable laws or regulations.
The Software and documentation have been developed entirely
at private expense and are provided as “Commercial Computer
software - Restricted Rights” in accordance with FAR 52.227-
19 (1987) or limited rights provided for such Software and
documentation by the applicable FAR or DFARS clause or this
Sony Software License Agreement.
Limited Warranty
Sony warrants to User that the Software will not fail to execute
its programming instructions due to defects in material and
workmanship for a period equal to the warranty period provid-
ed for the Product when properly installed and used. Warranty
does not apply to defects resulting from (a) improper or inade-
quate maintenance, (b) software, interfacing, parts or supplies
not supplied by Sony, (c) unauthorized modification of the
Software or the Product, or (d) improper site preparation or
maintenance. If Sony receives notice of a covered defect(s)
during the warranty period, Sony will replace Software that
does not execute its programming instructions due to such
defect(s). Sony does not warrant that the operation of the
Software and / or Product will be uninterrupted or error free. If
Sony is unable, within a reasonable time, to repair or replace
any Software to a condition as warranted, User shall be entitled
to a refund of the purchase price upon prompt return of the
Product. EXCEPT AS SPECIFICALLY STATED ABOVE,
THE SOFTWARE IS PROVIDED “AS IS” WITHOUT
WARRANTY AND SONY, IT S AFFILIATES AND ITS
THIRD PARTY LICENSORS DISCLAIM ANY IMPLIED
WARRANTY OF NON INFRINGEMENT, MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. THE REMEDIES IN THIS WARRANTY
STATEMENT ARE USER’S SOLE AND EXCLUSIVE
REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO
EVENT WILL SONY, ITS AFFILIATES OR ANY OF ITS
THIRD PARTY LICENSORS BE LIABLE FOR LOSS OF
DATA OR FOR DIRECT, INDIRECT, SPECIAL, INCI-
DENTAL, CONSEQUENTIAL (INCLUDING LOST
PROFIT), EXEMPLARY, OR OTHER DAMAGE,
WHETHER BASED IN CONTRACT, TORT, OR OTHER-
WISE, EVENT IF SUCH PARTY HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. IN NO
EVENT WILL SONY OR ANY OF ITS AFFILIATES OR
THIRD PARTY LICENSOR’S LIABILITY UNDER
AGREEMENT, WHETHER IN CONTRACT, TORT OR
OTHERWISE, EXCEED THE COST OF THE PRODUCT.
General
This Agreement shall be deemed to have been made and exe-
cuted in the State of California and both parties agree that any
dispute arising hereunder related to this Agreement or the
Product will be governed by laws of the State of California,
exclusive of its conflicts of law principles and that the courts in
the County of San Diego, California will have exclusive juris-
diction over all such disputes. FURTHER THE PARTIES
HEREBY WAIVE TRIAL BY JURY IN CONNECTION
WITH ANY ACTION OR SUIT ARISING UNDER THIS
AGREEMENT OR OTHERWISE ARISING FROM THE
RELATIONSHIP BETWEEN THE PARTIES HERETO. This
Agreement shall be binding upon the parties’ authorized suc-
cessor and assignees. Neither party’s waiver of any breach or
failure to enforce any of the provisions of this Agreement at
any time shall in any way affect, limit or waive such party’s
right thereafter to enforce and compel strict compliance with
every other provision. No modification of this Agreement shall
be effective unless in Writing signed by both parties.
122
Index
A
Access Card 19, 35, 109
Advanced Program Guide™ 15, 49-60
Advanced Setup 94
Analog Audio Signals 13
Analog TV Connection 27
ANT IN Jack 23, 25-31
Antennas Connection 23-26
Arrow Keys, on front panel 36
Aspect Ratio Setting 88-90
ATSC 9
Audio Connection 33, 34
Audio Language 87
Audio Mode 85
Audio Out Jacks 28-31, 34
Audio Setting 83-87
Auto DVI 11
Auto Program 75
Azimuth 68-69, 73-74
B
Back Panel 20, 21
Batteries 18, 19
Block Channel 97
C
Cable In Jack 20, 23-26
Cables 18, 19
Category Search 59
Keyword Search 60
CC button 37, 51
Channel Banner 44, 45
Channel Setup 71
Clock Setting 79, 80
Closed Caption Setting 91, 92
Component Out Jack 11, 19, 20, 28
Connecting to Analog TV 27
Connecting to Antennas 23-26
Connecting to Audio System 33, 34
Connecting to HD Monitor(DVI type) 30
Connecting to HD Monitor(RGB type) 29
Connecting to HD Monitor(Y/Pb/Pr type) 28
Connecting to VCR 31, 32
Connection Overview 22
D
Data Port 21
Digital Audio Out (Optical) Jack 21, 33
Digital Audio Out Setting 83, 84
Digital Audio Signals 14
DTV Caption 92
Digital Output 83
Dish Selection 67
Display Formats 11
Dolby Digital 14, 33, 83, 84, 86
DVI-HDTV Port, Cables 18, 19
E
Elevation 73
F
Favorite Channel 46
Favorite Channel Edit 77
FCC Regulations 1
Features 8
FORMAT button, front panel 36
FORMAT button, remote control 39
Format setting 11
1080i Format 11, 28, 29, 30
720p Format 11, 28, 29, 30
480p Format 11, 28, 29, 30
Variable 1/2/3 Format 11
Auto DVI Format 11
480i Format 11, 27, 31
Front Panel 36
Freeze Screen 47
Future Viewing 57
G
Guide 61
H
Help 8, 17, 112, 113
Hook-up Help 8, 17, 82, 113
I
Initial Setup 43, 67-74
L
Limited Warranty 119
Location 73
Locks Setting 96-101
Lock System 96
M
Messages Checking 64
Movie Rating 98
N
NTSC 9
Native 10
O
Output Channel Setting 81
Out to TV Jack 20, 27-31
Out to TV Setting 81
P
PCM (Digital) 14, 83, 84
Purchase List Managing 63
Purchasing DIRECTV®Pay Per View programs 58
R
Receiving Signals 23-26
Remote Control, buttons and functions
37–39
Remote Control Codes for Other Components
41, 42
Remote Control Programming 40
Replace Card 109
RF Antenna 18, 19
RF Jacks, Cables 18, 19
RGB/DVI-HDTV Out Ports 20
Reset 36, 117
S
SAP 15, 85
Satellite In Jack 21, 24-31
Signal Strength 74
Software License Agreement 120
Specifications 114
Spending Limit 101
S-Video Jack 19-20
System Test 106-108
System Upgrade 105
T
Telephone Jack 19
Testing the System 106-108
Tilt 73
Timer/Record List 65
Troubleshooting 115-117
TV Connection 27-30
TV Rating 99, 100
TV Signal Formats 10
U
Unlocking System 96
V
VCR Connection 31
VCR Controller 32
Video Out Jacks 19, 20
Y
YPbPr (component) out jack 11, 18, 19, 20, 28
W
Warranty 119
Wide Mode 12, 13, 88, 89
Z
Zip Code 73
Printed in KOREA
Contact DIRECTV with questions about
service, programming or billing:
1-800-DIRECTV (347-3288)
www.DIRECTV.com
Contact Sony with questions about your
Digital Satellite Receiver:
1-800-838-SONY (7669)
www.sony.com/support