Sanwa Electronic Instrument Co RX-491 2.4GHz Radio Control System User Manual 670A02593A

Download:
Mirror Download [FCC.gov]
Document ID	4022232
Application ID	eobnfhnlUbgs/t7IXbh9KQ==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	160.73kB (2009114 bits)
Date Submitted	2018-09-28 00:00:00
Date Available	2018-09-28 00:00:00
Creation Date	2018-08-09 11:32:14
Producing Software	Adobe PDF library 7.77
Document Lastmod	2018-09-07 16:56:43
Document Title	670A02593A表
Document Creator	Adobe Illustrator CS2

Sanwa Electronic Instrument Co., Ltd
2.4GHz Radio Control System
670A02593A
Operation Manual
Thank you for your purchasing SANWA 2.4GHz Receiver “RX-491.”
This product manual explains correct uses, safe uses, and product notifications.
Please read the manual and follow steps and cautions before using.
If you read the manual, please keep it whenever you need to read.
PRECAUTIONS AND WARNINGS
●RX-491(２.４ＧＨｚ Spread spectrum transmission system receiver) is for compatible FH5 transmitter as M17.
Other AM/FM/2.4GHz transmitter cannot use.
●To combine with devices compatible with SSL can be changed setting by transmitter CODE AUX function.
●Analog servos is not compatible with SUR , SSR, SHR mode. You must use analog servos by
NOR mode. If using analog servos by SUR, SSR, SHR mode, the analog servos will be broken.
(Analog servos: Hyper ERG series, RS-995, SZ-165T, SPEC series)
BL-RACER/BL-FORCE/BL-sport, F3300, F3000, F2200, SBL-01/02/03CR cannot work by SUR, SSR,
and SHR mode. You MUST use the ESC by NOR mode.
●2.4GHz frequency band is not only for Radio Control. This frequency band is same as ISM (industrial,
scientific, and medical device) use. There are some possible of interfering by the other devices as
Microwave, wireless LAN, digital cordless phone, audio device, gaming device, and bluetooth device,
and VICS. Also, amateur radio uses same frequency band. Please take care of interfering form
other devices. In case of interfering to the radio station, please stop to use and avoid the interfere.
●Please check safe use and limit to use devices are possible to be interfered in RC circuit.
Also, please follow instructions by the facility manager.
●In case of running behind the building and steel tower, transmission function would be decline or
out of control. Please always operate in visible situation.
●If the 2.4GHz frequency band is saturated (too many transmitters on at once), as a safety precaution,
it may not pair when turned on. Once the frequencies have been cleared, or the saturation level has
dropped, your transmitter and receiver should pair when turned on without any problems.
NAME OF PARTS, LED CONDITION INDICATOR, AND ANTENNA CONDITION
Antenna
LED *Receiver condition can be checked by the LED condition
BIND Plug
SSL/BAT：BIND/SSL Port
*BIND/SSL port must connect with BIND plug,
Receiver battery, and compatible devices with SSL
CH4 : 4ch
CH3 : 3ch
CH2 : Throttle (FET Electric Speed Controller)
CH1 : Steering
LED condition indicator
Receiving RF Signal
Blue
No connection
None
Binding Operation
Blue Flash Slow
Blue Flash Fast
Flashing
Blue and Red
Battery Fail Safe Mode
No connection after
Battery Fail Safe
●Depending on the place receiver and antenna, reception distance may be different.
●Do not antenna tip is outside antenna pipe because of antenna protection.
Please put antenna in the pipe as right picture.
●MUST not hold antenna due to avoiding breaking of wire.
Do not pull off antenna. It will be caused failure inside receiver.
●Please place antenna as high as possible in your model.
●Do not cut off and bundle antenna due to avoiding to decline receiver sensitivity.
●Stand antenna vertically. Please place receiver apart from motor and
FET Speed Controller (include leads).
Flashing Red
Antenna Pipe
Antenna
SSL SYSTEM
●To combine with devices compatible with SSL can be changed setting by transmitter CODE AUX function.
●In case of using CODE AUX, please change AUX TYPE is [NOR] to [CODE5 or CODE10] in System.
To choose CODE5 or CODE10 depends on device which is compatible with CODE5 or CODE10.
●About CODE AUX, please refer SSL system explanation on our HP. (www.sanwa-denshi.com)
How to Bind with Transmitter
●About BIND : each 2.4GHz transmitter has ID Number. The bind is stored ID Number in receiver.
If receiver bind with transmitter, receiver will be worked by only the transmitter.
1. Please set [RF mode] is [FH5] in Transmitter System (Compatible with FH5 as M17)
2. Turn on the transmitter, and set for other devices as response mode. Then, enter [BIND] to be bind mode.
3. Connect BIND plug in RX-491 BIND/SSL port. Then, turn on receiver.
*When you bind transmitter with the receiver, please connect battery in empty port. (In case of EP car, speed controller connect in CH2 port)
4. After RX-491 LED will be changed fast flashing blue from slow flashing blue, please take off BIND plug and restart RX-491 (Turn off receiver, then turn on).
5. Please finish BIND mode on transmitter to use enter/back operation by touch pad. In case of binding with transmitter, LED on the receiver turn on blue.
Please operate device as servo to check BIND is completed.
* In case of turning off LED in the process or did not complete BIND setting, please reset binding form 2. in bind process.
Receiver LED Condition
BIND Plug
Turn on Battery Switch!
Connect Bind Plug
to the Bind Port
Binding operate (Flash for a second)
・・・・・・・・・・・・・・・・・・
Turn on receiver or
speed controller switch
・・・・・
BIND Complete (Fast Flashing for 0.1 second)
⇒
*Did not connect anything above picture
but please connect device as servos or
FET speed controller (except motor)
when you bind
・・・・・・・・・・・・・・・・・
Take off BIND Plug
and restart receiver
Finish Bind Mode
on transmitter (M17)
Turn on LED
ENTER
●About RX-491
RX-491 can store 2 transmitter ID Number. It is able to combine using individual transmitter which is different setting in endurance race .
If you bind with 2 different transmitter, the receiver store the different transmitter and can operate by transmitters without re-bind.
*CANNOT operate by the 2 different transmitter at the same time. 2 ID store system is only compatible with M17.
- Throttle neutral position or operation quantities might be different each transmitter. Please adjust each transmitter setting to fit chassis linkage.
- MUST set fail-safe setting on each transmitter.
- Please set same RF mode and response mode as 1st transmitter when you bind 2nd transmitter. If it was different mode, cannot bind with 2 transmitters.
*If 2nd transmitter was different RF node and response mode from 1st transmitter, 1st transmitter ID No. is deleted and only write 2nd transmitter.
*If you bound 3rd transmitter, 1st transmitter ID No. will be deleted.
！
WARNING
■ Default is not bind with transmitter. Please bind with transmitter before using.
■ MUST use the receiver with bound transmitter.
PRECAUTION FOR SAFE USE
● Please mount the antenna of receiver as high as possible in your model.
● Do NOT cut off the antenna and bundle the antenna.
● Stand antenna vertically. Please place receiver apart from motor and FET Speed Controller (include leads).
● Please check surely connection devices as servos and switch with the receiver. In case of loosing connection during running,
it is possible to be out of control.
● The receiver is weak in extreme vibration, shock, and water. Please take care of vibration, shock, and water.
● Please mount the receiver apart from carbon and metal chassis.
● Metal to metal contact in your model will generate to noise. It will interfere the receiver ability and is possible to be out of control.
● Please take noise killer condenser to brushless motor for RC car. If not taking noise killer condenser to brushless motor for RC car,
noise will be generated. It is possible to be out of control.
● Please use transmitter, servos, FET speed controller made by SANWA.
*in case of combine to use with the devices except SANWA devices, we could not take responsibility for any failures.
WARRANTY AND SERVICE INFORMATION
Your RX-491 is warranted against manufacture defects in materials and workmanship.
This warranty does not cover suitability for specific application, components worn by use or improper voltage,
tampering, modification, misuse, abuse, improper wiring, reverse polarity, moisuture damage or acts of Gods.
For warranty and service information, please contact the SANWA distributors in your region.
For a list of distributors in your region, please visit www.sanwa-denshi.com/rc/distributors.html.
SANWA Electronic Instrument CO., LTD
1-2-50 Yoshida-Honmachi
Higashi Osaka, 578-0982 JAPAN
Telephone : 81-72-962-1277
FACSIMILE: 81-72-964-2831
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-701
Format                          : application/pdf
Title                           : 670A02593A表
Creator Tool                    : Adobe Illustrator CS2
Create Date                     : 2018:08:09 11:32:14+10:00
Modify Date                     : 2018:09:07 16:56:43+08:00
Metadata Date                   : 2018:09:07 16:56:43+08:00
Thumbnail Width                 : 184
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 18773 bytes, use -b option to extract)
Document ID                     : uuid:C3080A677C9BE8119BDDA69CAF49D4C2
Instance ID                     : uuid:496d0f1b-b8c7-46e8-bf7b-be9d75f11211
Derived From Instance ID        : uuid:5d926934-d84e-489b-bdb4-490b2625bf2c
Derived From Document ID        : uuid:A20645F0A29AE811933E819E8C8B3D13
Startup Profile                 : Print
Type                            : Document
Producer                        : Adobe PDF library 7.77
Has XFA                         : No
Page Count                      : 3
Creator                         : Adobe Illustrator(R) 12.0
For                             : rc09, ���W�R���Z�p
Bounding Box                    : 0 0 596 842
Container Version               : 9
Creator Version                 : 12
AI Creator Version              : 12.0.0
AI Build Number                 : 198
AI Color Usage                  : Color
AI Ruler Units                  : Millimeters
AI Color Model                  : CMYK
AI Target Resolution            : 800
AI Num Layers                   : 1
Image Height                    : 842
Image Width                     : 596
Image Size                      : 596x842
Megapixels                      : 0.502

EXIF Metadata provided by EXIF.tools