Sanyo Vpc X1400 Instruction Manual

VPC-X1420 GX - Instruction Manual VPC-X1400_X1420 Free User Guide for Sanyo Camera, Manual

2015-08-20

: Sanyo Sanyo-Vpc-X1400-Instruction-Manual-796391 sanyo-vpc-x1400-instruction-manual-796391 sanyo pdf

Open the PDF directly: View PDF .
Page Count: 84

Download
Open PDF In Browser	View PDF

INSTRUCTION MANUAL
BASICS
Digital Camera

VPC-X1420EX
VPC-X1400
VPC-X1420GX
VPC-X1420PX

Important note
This manual explains how to safely operate the VPC-X1420EX, VPC-X1400,
VPC-X1420GX and VPC-X1420PX.
Any information regarding only one of these products will be labeled as such.
Please read these instructions carefully before using the camera.
Make sure to read and understand the separate booklet “SAFETY MANUAL”.
Keep this manual in a safe place for later reference.

Warning
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

kFOR AMERICAN USERS
The following advisory is included in accordance with the laws of the State of
California (USA):
WARNING:
This product contains chemicals, including lead, known to the State of
California to cause cancer, birth defects or other reproductive harm. Wash
hands after handling.
i This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
h Reorient or relocate the receiving antenna.
h Increase the separation between the equipment and receiver.
h Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
h Consult the dealer or an experienced radio/TV technician for help.
i Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Declaration of Conformity
Model number: VPC-X1400
Trade Name: SANYO
Responsible party: SANYO North America Corporation
Address: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.: (818) 998-7322
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.

English

FOR USERS IN THE USA
About the battery charger

IMPORTANT SAFETY
INSTRUCTIONS – SAVE THESE
INSTRUCTIONS
DANGER – TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE
INSTRUCTIONS
h For connection to a supply not in the U.S.A., use an attachment plug
adapter of the proper configuration for the power outlet.
h Power Supply Cord:
Use UL Listed detachable power supply cord - No. 18 AWG, two
conductors, rated 10 A, VW-1, 105 ºC, 125/250 V, minimum 1.8 m,
maximum 3 m long. Provided with a molded-on, non-polarized attachment
plug with a 15 A, 250 V (NEMA 2-15P) configuration or a 15 A, 125 V
(NEMA 1-15P) configuration and a molded-on connector which mates with
the Power Inlet.
Cord Type
Basic Cord Type

Other Suitable Types

TST

SP-2

SPE-2, SPT-2

SP-3

SPE-3, SPT-3

SVE, SVO, SVOO, SVT, SVTO, SVTOO

SJE, SJO, SJOO, SJT, SJTO, SJTOO

SE, SO, SOO, ST, STO, STOO

h This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

English

PARA LOS USUARIOS DE EE.UU.
Acerca del cargador de baterías

INSTRUCCIONES IMPORTANTE
SOBRE DE SEGURIDAD - GUARDE
ESTAS INSTRUCCIONES
PELIGRO - PARA REDUCIR EL
RIESGO DE INCENDIO O
DESCARGAS ELÉCTRICAS, SIGA
CUIDADOSAMENTE ESTAS
INSTRUCCIONES
h Para la conexión a una red de alimentación que no sea de EE.UU., utilice
el adaptador de enchufe apropiado para la toma de la red.
h Cable de alimentación:
Utilice el cable de alimentación UL desenchufable indicado en la lista - N.°
18 AWG, dos conductores, amperaje nominal de 10 A, VW-1, 105 ºC, 125/
250 V, mínimo 1,8 m, máximo 3 m de longitud. Provisto de enchufe
moldeado, adaptador de enchufe no polarizado con configuración de 15 A,
250 V (NEMA 2-15P), o configuración de 15 A, 125 V (NEMA 1-15P) y
conector moldeado que se adapta a la toma de corriente de la red.
Tipo de cable
Tipo de cable básico
TS
SP-2
SP-3
SV
SJ
S

Otros tipos adecuados
TST
SPE-2, SPT-2
SPE-3, SPT-3
SVE, SVO, SVOO, SVT, SVTO, SVTOO
SJE, SJO, SJOO, SJT, SJTO, SJTOO
SE, SO, SOO, ST, STO, STOO

h Este dispositivo cumple con lo estipulado en la Parte 15 de las Normativas
de la FCC. La operación está sujeta a las dos condiciones siguientes: (1)
este dispositivo no puede provocar interferencias nocivas, y (2) este
dispositivo debe aceptar las interferencias recibidas, incluidas las
interferencias que puedan provocar un funcionamiento no deseado.

iii

English

kFOR CANADIAN USERS
i This Class B digital apparatus complies with Canadian ICES-003.

kFOR EU USERS
The symbol mark and recycling systems described below apply to EU
countries and do not apply to countries in other areas of the world.
Your SANYO product is designed and manufactured with high quality
materials and components which can be recycled and/or reused.
The symbol mark means that electrical and electronic equipment, batteries
and accumulators, at their end-of-life, should be disposed of separately from
your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this chemical
symbol means that the battery or accumulator contains a heavy metal at a
certain concentration. This will be indicated as follows: Hg: mercury, Cd:
cadmium, Pb: lead
In the European Union there are separate collection systems for used
electrical and electronic equipment, batteries and accumulators.
Please, dispose of them correctly at your local community waste collection/
recycling centre.
Please, help us to conserve the environment we live in!

SANYO Sales & Marketing Europe GmbH
Stahlgruberring 4, D-81829 München, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan

kFOR RUSSIAN USERS
This product is certified by an official certification company
which is authorized by the Russian Federation.

English

HOW TO READ THIS MANUAL
This instruction manual for your camera is organized into the following
sections.
k SETUP
Before taking pictures with your camera, you will need to familiarize
yourself with a few of its functions and complete some setup steps.
k BASIC OPERATION
An explanation of the fundamental operation for capturing images and
viewing images.
k APPENDICES
The camera specifications are found here.

kSymbols used in this manual
HINT
CAUTION
(page xx)

Points giving some extended instructions or special points to pay
attention to.
Points that require special attention.
Refer to the page indicated for detailed information.

You may find the answers to questions or problems concerning camera
operation in the ADVANCED INSTRUCTION MANUAL.
For information concerning how to use the accompanying CD-ROM (SANYO
Software Pack), please see the file “SANYO Software Pack INSTRUCTION
MANUAL.”

kHow to view the “INSTRUCTION MANUAL:
ADVANCED” and “SANYO Software Pack
INSTRUCTION MANUAL” files
1 Insert the CD-ROM (SANYO Software Pack) that was included with
your camera in your computer’s CD-ROM drive.
2 Install the Adobe Reader 9 on your computer.
3 On the installation screen, click on “Instruction Manuals (PDF)”.
4 Click on the desired instruction manual.

English

SHOOT, PLAY BACK AND SAVE
Install the battery pack

Use the supplied charger to charge the battery pack.
h The CHARGE indicator is lit during charging.
h The CHARGE indicator will turn off when the battery pack is fully charged.
h Charging takes approximately 120 min.
Battery pack charger
Battery pack
[J] mark

CHARGE indicator

To power outlet

Open the battery/card compartment cover, and insert the battery pack.
h The battery/card compartment cover is located on the bottom of the
camera.
h Press the ON/OFF button to turn the camera on.
ON/OFF button
[J] mark

English

SHOOT, PLAY BACK AND SAVE
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i Sanyo declines any claim for compensation for recorded contents etc. in case
of photographing or recording failure due to a chance camera or card flaw.

Shooting

Toggle the SET button to the left.
h The recording mode menu
appears.
Single-shot
High-speed sequential shots
Sequential shots
Video clip recording

Shutter button

SET
button

PHOTOGRAPH 1 IMAGE

2
3
4

vii

Toggle the SET button to the left or
right to select the recording mode.

Press the SET button.
h The recording mode is
indicated by an icon in the
upper left area of the monitor.
Press the shutter button.
Single-shot mode:
A still image is captured.
High-speed sequential shots
mode/sequential shots mode:
Shooting begins. Release the
shutter button to discontinue
shooting.
Video clip recording mode:
Recording begins. To stop
recording, press the shutter
button again.

English

s: Single-shot mode
: High-speed sequential shots mode
O: Sequential shots mode
X: Video clip recording mode

Playback
kStill image playback

Press the playback button [=].
h The display switches to the
Playback Screen.
h To view other images, toggle the
SET button to the left or right.
h If the playback button [=] is
pressed, the display returns to
the Shooting Screen.

ON/OFF button
Playback button
[=]

kVideo clip playback

Press the playback button [=].
h The display switches to the
Playback Screen.
h Toggle the SET button to the left
or right to display the video clip
you wish to play back.
Press the SET button.
h Playback of the selected video
clip begins.
h If the playback button [=] is
pressed again, the display
changes to the Shooting Screen.

SET button

SET PLAY

When you are finished taking pictures...
Press the ON/OFF button to turn the camera off.
HINT
i To record with the video size set to #, please make sure that a card is
installed in the camera. If there is no card installed, the # setting is not
available. In addition, please use a high-speed (write speed) card for
recording video clips.

English

viii

SHOOT, PLAY BACK AND SAVE
Copying files to a computer (Windows XP)

Install the software.
1 Insert the CD-ROM (SANYO Software Pack) that was included with
your camera in your computer’s CD-ROM drive.
h The installation screen appears.
2 Click on [ArcSoft MediaImpression 2] in the installation screen.
h Follow the messages on your computer screen to install the
software.
Use the supplied USB interface cable to connect your camera to the
computer.
h Connect the camera’s USB/AV terminal to the computer’s USB
connector.
h The USB Connection Screen appears on the camera’s monitor.

USB CONNECT ION
COMPUTER
PRINTER
CANCEL

To USB
connector on
the computer

SET OK
CANCEL

Supplied
dedicated USB
interface cable

To the USB/AV terminal

English

3
4

Select “COMPUTER”, and press the SET button.
h The screen to select the connection mode appears.
Select “CARD READER”, and press the SET button.
h The camera is connected in the card reader mode.
h If the Windows automatic playback screen appears on the computer
monitor, close it.
Double-click on the desktop [MediaImpression 2] icon to launch
MediaImpression 2.
h The MediaImpression 2 home page appears.
[Import]

English

SHOOT, PLAY BACK AND SAVE

Click on [Import].
h The files in the camera are shown on the import screen.
Files in the camera

[Destination Folder] field and [Subfolder Name] field
[Import]

English

HINT
You can specify which folder to copy the files to
i When you click on the folder icon in the [Destination Folder] field, the
screen to specify the copy destination appears.
i We suggest that you click on [{Today’s Date] in the [Subfolder Name] field
to select it. When [{Today’s Date] is selected, a subfolder named with the
current date is automatically created in the folder specified in the
[Destination Folder] field, and the files are copied to it.
Folder icon

7
8
9

Click on [Import].
h The files in the camera are copied to the computer.
When copying is completed, click on [Done].
h You are returned to the MediaImpression 2 home page.
Click on the close button to exit MediaImpression 2 and end the
program.

HINT
More about MediaImpression 2
i On the MediaImpression 2 home page, click on [Service & Support] for
more information.

English

xii

SHOOT, PLAY BACK AND SAVE
Dismounting the camera
CAUTION
i To disconnect your camera, be sure to follow the procedure below. Failure
to follow this procedure may cause faulty operation of your computer or
loss of card data.

1
2

Left-click on the icon for safely removing hardware.
h A list appears showing the devices connected to the computer’s USB
connectors.
Left-click on the camera drive (E:).
h The camera can now be disconnected.
hThe drive name (E:) may be different on your computer.

xiii

English

CAUTION
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
i Please connect the dedicated USB interface cable to your computer’s USB
connector. Do not connect it to the USB port on your monitor or keyboard,
or to the USB hub. Be especially careful when installing the driver
software. In some instances, it may not be possible to correctly install the
driver software.
To access the data in the camera’s internal memory...
i Remove the card from the camera.

English

xiv

CONTENTS
CHECKING THE INCLUDED ACCESSORIES ...................................... 3
Attaching the handstrap ..................................................................... 4
Media cards that can be used with this camera ................................. 4
What “card” means in this manual ..................................................... 4
Installing/removing the DC adaptor (Model VAR-A3:
sold separately) ............................................................................. 5

SETUP
PARTS NAMES ..................................................................................... 6
CHARGING THE BATTERY PACK ....................................................... 8
Charging the battery pack .................................................................. 9
INSTALL THE BATTERY PACK AND CARD ...................................... 12
Installation ........................................................................................ 12
To format a card .............................................................................. 14
Warning concerning battery pack temperature ................................ 15
TURNING THE CAMERA ON AND OFF ............................................. 16
Turning on the camera ..................................................................... 16
Turning off the camera ..................................................................... 16
About the auto power off function .................................................... 17
DATE AND TIME SETTING ................................................................. 18

BASIC OPERATION
BEFORE TAKING PICTURES ............................................................. 21
Switching between the recording mode and playback mode ........... 21
How to switch the recording mode ................................................... 22
Switching the display mode ............................................................. 23
Adjust the monitor brightness .......................................................... 24
Hints for taking pictures ................................................................... 25
CAPTURING AND PLAYING BACK STILL IMAGES .......................... 26
Shooting single shots ....................................................................... 26
Shooting sequential shots ................................................................ 28
Viewing still images ......................................................................... 30
12-image/20-image display playback .............................................. 31
Folder playback ............................................................................... 32
Magnifying (zooming in) the image .................................................. 33
Zoom jump playback ........................................................................ 34
Deleting files .................................................................................... 35
VIDEO CLIP RECORDING AND PLAYBACK ..................................... 37
Recording a video clip ..................................................................... 37
Playing back the video clip .............................................................. 38

English

USING THE SCENE FUNCTION .........................................................41
Capture a still image with a voice memo ..........................................43
How to use the best shot feature ......................................................44
How to create a panorama photo .....................................................45
How to use the face chaser feature ..................................................47
How to shoot using Smile Detection .................................................48
OTHER RECORDING FUNCTIONS ....................................................50
Using the zoom ................................................................................50
Flash setting .....................................................................................52
Self-timer ..........................................................................................54
Focus range .....................................................................................56
ACCESSING THE MENUS ..................................................................59
How to display the menus ................................................................59
How to operate the menus ...............................................................60

APPENDICES
SPECIFICATIONS ................................................................................61
Camera .............................................................................................61
Camera connectors ..........................................................................64
Battery life ........................................................................................64
Possible Number of Images/Video Recording Time/
Audio Recording Time .................................................................65
Supplied battery pack charger ..........................................................66
Supplied Li-ion battery pack .............................................................66
Others ...............................................................................................67
Before capturing those important shots, be sure to first
take a test shot to confirm that your camera is set up and
ready to go ...................................................................................68

English

CHECKING THE INCLUDED ACCESSORIES
i Handstrap: 1

i SANYO Software Pack
(CD-ROM): 1

i Lithium-ion battery pack
(battery pack): 1

i Lithium-ion battery pack
charger and power cord

i Dedicated USB interface cable:
1

i Dedicated AV interface
cable: 1

i SAFETY MANUAL
(safety precautions booklet)
Please read this booklet
carefully before using the
digital camera.

i QUICK GUIDE

i INSTRUCTION MANUAL
BASICS
(VPC-X1420EX,
VPC-X1420GX,
VPC-X1420PX only)

English

Attaching the handstrap

Media cards that can be used with this camera
The types of card that can be inserted into and used with this camera are:
i SD Memory Card
i SDHC Memory Card
i SDXC Memory Card

What “card” means in this manual
i In this manual, SD Memory Cards, SDHC Memory Cards and SDXC
Memory Cards that can be used in this digital camera are referred to as
“card”.

English

CHECKING THE INCLUDED ACCESSORIES
Installing/removing the DC adaptor (Model VAR-A3: sold separately)
Install in the camera’s battery slot, and connect the AC adaptor. Use in
conjunction with the AC adaptor.

Attaching the DC adaptor
1 Open the camera’s battery/card
compartment cover.

2 Insert the DC adaptor into the battery slot.
h Make sure that the DC adaptor is correctly oriented when inserting,
and insert it firmly all the way.

3 Close the battery/card
compartment cover.

4 Connect the AC adaptor.

Removing the DC adaptor
1 Turn off the camera.
2 Remove the AC adaptor.
3 Open the camera’s battery/card compartment cover, and remove the
DC adaptor.

English

SETUP

PARTS NAMES
Front
SCENE button
Shutter button
ON/OFF button

Flash
Lens

Self-timer indicator

Bottom

Battery/card compartment cover

Tripod stand hole
Speaker

English

PARTS NAMES
Rear
USB/AV terminal cover

Strap holder

Monitor

Zoom switch

Playback button [=]

SET button

MENU button

English

CHARGING THE BATTERY PACK
Please charge the supplied battery pack before using it.

Connect the supplied power
cord to the socket on the
battery pack charger.
h Insert the connector straight
and securely.

Battery pack charger
Power cord

Battery pack charger
Battery pack
[J] mark

Insert the battery pack in the
battery charger.
h Insert it in the direction
indicated by the [J] mark on
the battery pack.

CHARGE
indicator

To power outlet

Plug the power plug into a
power outlet (AC 100 V to
240 V).
h Charging begins.
h The CHARGE indicator is lit
during charging.
When the CHARGE indicator
turns off, unplug the power
cord from the power outlet,
and remove the battery pack
from the charger.

HINT
i Charging takes approximately 120 min.

English

CHARGING THE BATTERY PACK
Charging the battery pack
Be sure to fully charge the supplied or separately sold battery pack before
using it in your camera. For charging the battery pack, use the supplied
charger.
Charge the battery pack if it is being used for the first time, and recharge it
whenever the remaining charge is low.
Does the battery pack feel hot?
i During charging, the charger and battery pack will be warm. This is normal
and does not indicate a malfunction.
If there is interference to your TV or radio during charging...
i Move the battery pack and charger further away from the TV or radio.
Ambient temperature during charging
i It is recommended that the ambient temperature during charging be
between about 10 °C and 35 °C (50 °F and 95 °F). Due to the
characteristics of the battery pack, at temperatures below 0 °C (32 °F), it
may not be possible to sufficiently charge it.
i When the battery pack temperature is high, the safety function may be
activated and halt charging.
Charge a battery pack in the following cases
i A battery pack which has not been used for a long time
i Newly purchased battery pack
FOR AMERICAN USERS:
i Use a UL Listed, 1.8 to 3 m (6 to 10 ft.), Type SPT-2 or NiSPT-2, AWG
No.18 power supply cord, rated for 125 V 7 A, with a non-polarized NEMA
1-15P plug rated for 125 V 15 A.

English

About the CHARGE indicator
The CHARGE indicator shows the status of the battery pack and the charger.
Please refer to the following table if the indicator flashes abnormally.
CHARGE indicator
Not lit

Not connected properly
i To recharge the battery pack, the power cord of the
charger must be connected to a power outlet, and the
plug at the other end inserted in the charger’s power
socket (page 8).
i The battery pack is not installed, or it is not installed
correctly (page 8).
Charging finished

Lit

Charging

Flashing

Problem with the battery pack or battery pack charger
i Immediately remove the battery pack from the charger.
i Do not use an abnormal battery pack. (The usable life of
the battery pack has probably expired.)

CAUTION
Do not charge the battery pack immediately after the camera has been
in continuous use for a long time
i The battery pack becomes hot when the camera is used continuously for a
long time. If you attempt to charge the battery pack in this state, the safety
function may be activated and it may not be possible to charge the battery
pack. Wait until the battery pack has cooled down before attempting to
charge it.
Does the battery pack appear swollen?
i The lithium-ion battery used in this camera may expand slightly when
stored in a hot environment or repeatedly used, but this is not a safety
hazard.

English

CHARGING THE BATTERY PACK
HINT
About the internal backup battery
i This camera’s internal battery serves to maintain the date and time
settings, as well as the shooting settings. The backup battery will be fully
charged when the battery pack is kept in the camera continuously for about
2 days. In the fully charged state, the backup battery will maintain the
camera settings for about 7 days.
When not using the camera for a long time, remove the battery pack
i A small amount of power is still used even if the digital camera is turned off,
and it is therefore recommended that the battery pack be removed from the
camera if it is not going to be used for a long time. Note that when the
battery pack is removed for a long period, the time and date settings may
be cleared. Before using your camera again, be sure to confirm that the
camera settings are correct.
To prolong the life of the battery pack
i Although the battery pack is an expendable item, you can maximize the life
of the battery by heeding the following suggestions.
h Do not leave the battery under the hot summer sun or exposed to other
high-temperature environments.
h Do not continually recharge the battery when it is already fully charged.
After fully charging it once, for example, use it for a while to partially
discharge it before charging it again.
h When the battery is not to be used for a long time, if possible store the
partially charged (not fully charged) battery in a cool environment.

English

INSTALL THE BATTERY PACK AND CARD
Installation
i Make sure that the battery pack and card orientation are correct.
i The card can be used after it has been formatted with the camera.

[J] mark

Open battery/card compartment cover
on the bottom of the camera.

Insert the card all the way until it
clicks.

Close the battery/card compartment
cover.

To remove...

1 Open

1 Open
2 Push

2 Push down
3 Pull out

3 Pull out

English

INSTALL THE BATTERY PACK AND CARD
CAUTION
Do not remove the battery pack outer covering or label
i Do not use the battery with the outer covering or label removed, as doing
so may result in malfunction.
Be careful when removing the card
i Do not attempt to forcibly remove the card.
i Never remove the card when the camera is connected to a computer or
printer, or when the self-timer indicator is flashing quickly. In doing so, you
risk losing the data stored in the card.
Keep your finger on the card until it is completely inserted or released
i If you remove your finger too soon, the card may spring out and become
lost or hit someone in the eye.
HINT
Shooting without a card installed
i When a card is installed, images are recorded to and played back from the
card. When no card is installed, images are recorded to and played back
from the camera’s internal memory. When the camera is turned on with no
card installed, the internal memory icon
is shown on the monitor to let
you know that the images you capture will be saved to the camera’s
internal memory.

English

To format a card

Install the card in the camera. Turn
on the camera (pages 12 and 16).

Display the menu (page 59).

Display the Option Menu (page 60).

Select “FORMAT” and press the
SET button.
h The Format Screen appears.
Follow the instructions on the
screen to format the card.

MENU button

RECORDING MENU 1/2
RESOLUTION
10M
COMPRESSION
PHOTO STABILIZER
FOCUS MODE
EXP MEASURE
ISO
SET OK

English

INSTALL THE BATTERY PACK AND CARD
Warning concerning battery pack temperature
i If the battery pack in the camera becomes too hot, a blinking temperature
warning icon \ will appear on the monitor. If the blinking icon does
appear, the camera should be turned off as soon as possible and the
battery pack allowed to cool before the camera is turned on again.
i Note that the camera will turn off automatically if it continues to be used
with the battery pack temperature elevated.

English

TURNING THE CAMERA ON AND OFF
Turning on the camera
In the recording mode

Press the ON/OFF button.
h The camera turns on.
h The camera turns on in the
recording mode that was active
before it was last turned off.

ON/OFF button

In the playback mode

Press the playback button [=] for
at least one second.
h The Playback Screen appears on
the monitor (pages 30 and 38).

Playback button [=]

Turning off the camera

Press the ON/OFF button.
h The camera turns off.

h When the playback button [=] or ON/OFF button is pressed, the
camera turns off.

English

TURNING THE CAMERA ON AND OFF
About the auto power off function
In order to preserve battery pack power when, for example, the camera has
accidentally been left on, the camera is furnished with an “auto power off”
function by which the camera automatically turns off after a certain period of
inactivity (about 1 minute during shooting or about 3 minutes during playback
[factory default settings]).
i If the auto power save function has operated to turn the camera off, press
the ON/OFF button to turn it back on.
i You can change the setting for the time elapsed before the camera
automatically turns off.
i When the camera is connected to a computer or printer using the
dedicated USB interface cable, the auto power save function is disabled,
and the camera turns off after about 12 hours.
HINT
If the K icon appears...
i When a picture is taken, the date and time it was captured is recorded with
it. When the date and time cannot be recorded with the image because the
date and time have not yet been set (page 18), the K icon appears. To
have the date and time recorded with images, please make this setting
before capturing images.

English

DATE AND TIME SETTING
The camera will record the date and time an image or audio recording is
taken so that you can display them during playback. Therefore, before
capturing images, make sure the correct date and time are set.
hTo correct the date and time setting, please see under HINT on page 20.
Example: To set the clock to 7:30 p.m. on December 24, 2010

Turn on the camera (page 16), and
press the SET button.
h The Clock Set Screen appears.
h Follow the procedures below to
enable or disable the date display
during playback, to set the display
format for the date, and to set the
date and time.
h To display the Recording or
Playback Screen, press the
MENU button 2 times.
Set the date.
1 Select “DATE”.
2 Press the SET button.
h The Set Date Screen appears.
3 Set the date to “2010/12/24”.
h The date is set in the following
order: Set the year → Set the
month → Set the day.
h Toggle the SET button left or
right to select year, month or
day.
Toggle the SET button up or
down to increase or decrease
the number.
4 Press the SET button.

CLOCK SET
2010/01/01
00:00
Y/M/D

DATE
TIME
DISP

SET OK

CLOCK SET
DATE

2010/12/24

SET OK

English

DATE AND TIME SETTING

Set the clock.
1 Select “TIME”.
2 Press the SET button.
h The Set Time Screen appears.
3 Set the time to “19:30”.
h The time is set in the following
order: Set the hour → Set the
minute.
h A 24-hour clock is used for the
time display.
4 Press the SET button.
Set the order in which the date is
displayed during playback.
1 Select “DISP”.
2 Press the SET button.
h The Set Date Format Screen
appears.
3 Toggle the SET button up or down.
h The date display format
changes.
4 Press the SET button.

English

CLOCK SET

TIME

19:30

SET OK

CLOCK SET

DISP
SET OK

Y/M/D

Press the MENU button.
h The date and time setting is completed.
h To display the Recording or Playback Screen, press the MENU button.

HINT
About the settings backup
i Under normal conditions, while the battery pack is being replaced, an
internal battery will maintain the date and time settings. However, there is a
small chance the settings may be lost (the backup will last for about
7 days). It is recommended to check that the date and time settings are still
correct after replacing the battery pack and before shooting or recording of
any type (follow step 1).
To correct the date and time settings
1 Turn on the camera, and press the MENU button.
2 Select the [E] tab, and press the SET button.
3 Select “CLOCK SET” and press the SET button.
h The screen to set the date and time appears.
h The current date and time settings are shown.
4 Select the line you wish to change, and make the correction.

English

BASIC OPERATION

BEFORE TAKING PICTURES
Switching between the recording mode and
playback mode
Switch between shooting and playing.

1
2

Press the ON/OFF button to turn
the camera on.

ON/OFF button
Playback button
[=]

Press the playback button [=].
h Each time the playback button is
pressed, the camera switches
between the recording mode and
the playback mode.

149

100-0001

2010.12.24

HINT
To turn the camera on in the playback mode
i Press the playback button [=] for at least 1 second, and the camera will
turn on in the playback mode.

English

How to switch the recording mode
Your camera can capture single still photos (single-shot mode), record video
clips (video clip recording mode), and also capture a series of still photos
(sequential shots mode).

1
2

3
4

Press the ON/OFF button to
turn the camera on.

ON/OFF button

Toggle the SET button to the
left.
h The screen to set the
recording mode and the selftimer appears.
Toggle the SET button to the
right to select the recording
mode.
Press the SET button.
h The selected recording mode
is set.
h An icon in the upper left area
of the monitor indicates the
active recording mode
setting.

SET button

149

s: Single-shot mode
: High-speed sequential shots mode
O: Sequential shots mode
X: Video clip recording mode

English

BEFORE TAKING PICTURES
Switching the display mode
In the recording mode, you can select the either the “settings display mode”
which allows you to confirm the shooting settings on the monitor while you
shoot, or the “normal display mode” in which the setting indications are turned
off, providing a full view of the subject.

1
2

Press the ON/OFF button to turn
the camera on.

ON/OFF button
SET button

Press the SET button.
h Each time the SET button is
pressed, the camera switches
between the settings display
mode and the normal display
mode.

149

English

Adjust the monitor brightness
The brightness of the monitor is adjustable. Adjust the brightness to the
optimum readability in the ambient light.

1
2

3
4

Press the ON/OFF button to
turn the camera on.
Press the MENU button for at
least 1 second.
h The monitor brightness menu
appears.

ON/OFF button
SET button

Toggle the SET button to the
left or right to adjust the
brightness.
Press the MENU button.
h The monitor brightness is
set, and the monitor
brightness menu is canceled.
MENU button

HINT
i You can also adjust the monitor brightness by selecting “BRIGHTNESS”
from the Option Menu.

English

BEFORE TAKING PICTURES
Hints for taking pictures
Muting the camera sounds
i The operation sounds that are generated, for example, when the shutter
button, MENU button or SET button is pressed, can be muted.
Where is the image data saved?
i All the image and sound data is recorded in the camera’s internal memory
or on the card installed in the camera.
i When a card is installed in the camera, the data is recorded on the card. If
no card is installed, the data is recorded in the camera’s internal memory.
Taking pictures in backlight conditions...
i When taking pictures with the light coming from behind the subject, due to
the characteristics of the CCD, light lines or ghost patterns (flare effect)
may appear in the captured image. In this situation, it is recommended that
you avoid taking pictures with the subject lit from behind.
Switching the guidance display ON/OFF
i Toggle the SET button to the right. Each time the SET button is toggled to
the right, the guidance display switches between ON and OFF.

149

149
Push to
the right

Half-press shutter
button to focus

HINT
i Images captured in the still image shooting mode can be rotated when
they are played back.
i When the optical zoom is used or when the autofocus is operating, the
image may appear to waver, but this is not a malfunction.

English

CAPTURING AND PLAYING BACK STILL IMAGES
There are two modes for capturing still images. In the single-shot mode, one
image is captured each time the shutter button is pressed. In the sequential
shots mode, when you press the shutter button, several successive images
are captured. For more information about taking sequential shots, please see
page 28.

Shooting single shots

1
2

Set the camera to the singleshot mode (page 22).

Shutter button

Rest your finger on the
shutter button.
h Engage the autofocus by
pressing the shutter button
halfway (focus lock).

Gently press the shutter
button.
h Press the shutter button
gently, taking care not to
move the camera.
h The image that was
captured appears on the
monitor as long as the
shutter button is kept
pressed (post view).

F5.2
1/102
Single-shot icon

English

CAPTURING AND PLAYING BACK STILL IMAGES

Release your finger from the shutter button.
h The captured image is recorded.

HINT
Focus indicator
About the target mark
Target mark
i A target mark & on the monitor shows
the area the camera is focusing on.
i The camera automatically determines
the correct focus by measuring from 9
different focus points within the
shooting area. If the target mark is at a
position that is different from the point
you wish to focus on, you can refocus,
F5.2
for example, by changing the shooting
1/102
angle.
i The large target mark appears when
Shutter speed
the camera focuses on a wide area in
Aperture
the center of the screen.
About the focus indicator
Motion alert icon
i A green focus indicator appears when
the subject is successfully focused, or
a red focus indicator when the camera
was not able to focus the subject.
The shutter speed and aperture are
displayed
i The shutter speed and aperture
settings are also displayed on the
F5.2
monitor. You can use them as a
1/2
reference when shooting.
If the motion alert icon appears...
i During still image shooting, if the shutter speed is slow and the possibility
that the image may be blurred due to camera shake becomes high, the
motion alert icon may appear on the monitor. In this case, use a tripod to
stabilize the camera when shooting, or set the flash operation mode to
automatic (page 52).
i When shooting with the fireworks H scene function, the motion alert icon
always appears, but this is normal.

English

Shooting sequential shots
When the shutter button is pressed, still images are captured in succession.

Set the camera to the sequential
shots mode or the high-speed
sequential shots mode (page 22).

O: Sequential shots icon
: High-speed sequential
shots icon

143

Press the shutter button to start
shooting.
h Shooting sequential shots begins.
J Estimated maximum number of
sequential shots

Resolution

Max. no. of shots

Resolution

Max. no. of shots

Approx. 3 shots

Approx. 19 shots

Approx. 3 shots

E
D

Approx. 3 shots
Approx. 5 shots

Approx. 9 shots

Approx. 18 shots

[

Approx. 100 shots

h The quantities indicate the number of shots when the compression
rate is set to j.
h The maximum number of sequential shots will differ depending on the
subject.
h Note that if the shutter button is released during shooting, shooting
stops immediately.
h When shooting sequential shots with the resolution set to <, the
compression rate is fixed at 0.

English

CAPTURING AND PLAYING BACK STILL IMAGES
HINT
About the focus when shooting sequential shots
i When sequential shots are captured, the autofocus operates when the
focus lock is activated, fixing the focus.
Can the self-timer and/or flash be used?
i The self-timer and flash do not operate when shooting sequential shots.
i The following scene functions cannot be set.
\]H_a5n

English

Viewing still images
The steps for viewing both single shots and sequential shots are the same.

Press the playback button
[=].
h If the playback button [=]
was pressed to turn the
camera on, however, press the
playback button [=] for at
least 1 second.
h The image most recently
captured appears on the
monitor.

Playback button [=]

View other images.
h Toggle the SET button to the
left or right to display the
previous or next image.
To display the previous image:
Toggle the SET button to
100-0001
the left.
To display the next image:
Toggle the SET button to
the right.
h To return to the Shooting
Screen, press the playback
button [=].

h When the playback button [=] or ON/OFF button is pressed, the
camera turns off.

When you are finished viewing images...
i Press the ON/OFF button to turn the camera off.
HINT
For still images with voice memo (pages 42 and 43)...
i When the shutter button is pressed, the voice memo is played back.

English

CAPTURING AND PLAYING BACK STILL IMAGES
12-image/20-image display playback

1
2

Press the playback button
[=].

Zoom switch [W]/[T]

Press [W] ([P]) on the
zoom switch.
h The 12-image display
appears.
Select the image to play
back.
h Toggle the SET button left,
right, up or down to move
the orange frame to the
desired image, and press
the SET button.
Instead of pressing the
SET button, you can press
[T] ([]]) on the zoom
switch to show the image
full screen.
h If [W] ([P]) on the zoom
switch is pressed while the
12-image display is shown,
the display changes to the
20-image display.

SET button

Video clip

Audio recording
Still image

100
0001

0002

0003

0004

0005

0006

0007

0008

0009
Orange frame
Folder number

English

Image number

Folder playback
A convenient way to search through multiple folders, or to search for an image
that was recorded using Screen Capture.

1
2

Access the 12-image display screen (page 31).
Press [W] ([P]) on the zoom
switch 2 times.
h The screen to select the playback
folder appears.
h If [T] ([]]) on the zoom switch is
pressed, the camera changes to
the 20-image display (page 31).

SELECT FOLDER

100SANPH
101SANPH
102SANPH
SET OK

Select the desired folder, and press
the SET button.
h The first image in the selected
folder is displayed.
h At this time, if you press [W] ([P])
on the zoom switch, the images in
the selected folder are shown in the
12-image display.

English

CAPTURING AND PLAYING BACK STILL IMAGES
Magnifying (zooming in) the image

1
2

Display the image that you want to magnify.
Press [T] ([]]) on the zoom
switch.
h Magnification is enabled.
h The image is magnified, and the
central portion of image is
displayed.
h Toggle the SET button left, right, up
or down to view different parts of
the magnified image.
To magnify:
Magnification increases with each
press of [T] ([]]) on the zoom
switch.
To go back:
Magnification decreases with each
press of [W] ([P]) on the zoom
switch.
h Press the SET button to return to
the normal (100%) view.

107%

Press shutter to save
100% Move

HINT
The magnified portion of the image can be saved as a separate image
i Press the shutter button. The magnified portion is saved as a new still
image.

English

Zoom jump playback
You can magnify a portion of a still image to check the accuracy of the focus.

1
2

Display a still image to view
using zoom jump playback.

Zoom switch [W]/[T]

Press the SET button.
h The image is magnified.
h If the magnified view appears
to be in focus, then the
overall image will be in focus.
Toggle the SET button left,
right, up or down to move to
the part you wish to magnify,
and press [T] ([]]) on the
zoom switch.
h The displayed area is further
magnified.
To magnify further:
Magnification increases with
each press of [T] ([]]) on the
zoom switch.
To go back:
Magnification decreases with
each press of [W] ([P]) on the
zoom switch.
h Press the SET button again
to return to the normal size
(100%) screen.

SET button

223%

Press shutter to save
Move
100%

English

CAPTURING AND PLAYING BACK STILL IMAGES
Deleting files
You can delete files if you no longer need them. You can delete the files one
at a time, or all at once.

To delete files from the card, perform the delete procedure with the
card installed in the camera. To delete files from the camera’s
internal memory, remove the card before performing the delete
procedure.
Set the camera to the playback
mode, and toggle the SET button
up.
h The Delete Screen appears.
DELETE SINGLE:
Deletes one file at a time.
DELETE ALL:
Deletes all the files.

DELETE

DELETE SINGLE
DELETE ALL

SET OK

Delete the files.

1 Toggle the SET button to the left or right to display the file you wish to
delete.
2 Toggle the SET button up or down to select “DELETE SINGLE”.
h There is no confirmation screen when deleting single files. Before
pressing the SET button in step 3, please make sure that the
displayed image is one you wish to delete.
3 Press the SET button.
h The currently displayed file is deleted.
h To delete other files, repeat steps 1 to 3.

English

1 Toggle the SET button to the left or right to view the images and
check if it is OK to delete all the files.
2 Toggle the SET button up or down to select “DELETE ALL”.
3 Press the SET button.
h The Delete Confirmation Screen appears. To delete the files,
select “YES”, and press the SET button. When the file delete is
completed, “No image” is shown.
CAUTION
About protected images
i Files that are protected from accidental delete cannot be deleted. To delete
protected files, set the protect setting for the file to off, and then follow the
file delete procedure.

English

VIDEO CLIP RECORDING AND PLAYBACK
Recording a video clip

1
2

Set the camera to the video
clip recording mode
(page 22).

Shutter button

Press the shutter button.
h Video clip recording
begins. During recording,
the length of the video clip
and the remaining
recording time available
are shown on the monitor.
h It is not necessary to
continue pressing the
shutter button while
recording.
End the recording.
h Press the shutter button
again to stop recording and
save the video clip.

Recorded length (time) of
video clip
Remaining recording time
available

Video clip recording icon

English

00:45:00
00:00:30

Playing back the video clip

Press the playback button
[=].
h If the playback button [=]
was pressed to turn the
camera on, however, press
the playback button [=] for
at least 1 second.
h The video clip just recorded
appears on the monitor.

Playback button [=]

Press the SET button.
h Video clip playback begins.
h To stop playback, toggle the
SET button down.
SET button

SET PLAY

English

VIDEO CLIP RECORDING AND PLAYBACK
Outline of playback operation
To do this...
Stop playback
Pause
To extract a still image
To play back
one image
at a time
(singleframe step)
Slow
playback

Forward

While playback is paused, toggle the SET
button to the right.

Reverse

While playback is paused, toggle the SET
button to the left.

Forward
Reverse

Forward
To
accelerate
playback

Reverse

Return to normal playback
speed
Adjusting the volume

English

Do this
During playback, toggle the SET button down.
During playback, press the SET button.
During accelerated or slow playback, toggle
the SET button up.
While playback is paused, press the shutter button.

While playback is paused, press and hold the
SET button to the right.
While playback is paused, press and hold the
SET button to the left.
During forward playback, toggle the SET
button to the right.
iThe playback speed changes each time the
SET button is toggled to the right, as
follows:
Normal playback → 2× → 5× → 10× → 15×
Toggle the SET button to the left to resume
normal playback speed.
During forward playback, toggle the SET
button to the left.
iThe playback speed changes each time the
SET button is toggled to the left, as follows:
15× ← 10× ← 5×
Toggle the SET button to the right to resume
normal playback speed.
Press the SET button.
Louder: During playback, press [T] on the
zoom switch.
Softer: During playback, press [W] on the
zoom switch.

When you are finished viewing video clips...
i Press the ON/OFF button to turn the camera off.
CAUTION
How to save one frame from a video clip as a still image
1 Play back the video clip. Pause the playback at the point you wish to
“snap” a photo.
2 Press the shutter button.
i The currently displayed frame is saved as a still image.
The data for a video clip is very large
i Therefore, be aware that if the video clip is uploaded to a computer to be
played back, the computer may not be able to play back the video fast
enough, making it appear jerky. (The video will always be displayed
properly on the camera monitor.)
If video clip recording stops even when there is card memory
remaining…
i Depending on the card you are using, recording may stop even if there is
remaining memory in the card.
i For video clip recording, it is recommended that a high-speed memory
card be used.
If no audio is heard...
i The audio is not played back when the video clip is played back in the
frame-by-frame, slow playback, fast playback or reverse playback mode.
Does video clip playback stop when you adjust the volume?
i If you adjust the volume during video clip playback, the playback may
temporarily pause. This is not a malfunction.

English

USING THE SCENE FUNCTION
You can select from a variety of preset settings (aperture, shutter speed, etc.)
for specific shooting conditions.

Set the camera to the recording
mode (page 21), and press the
SCENE button.
h The screen to select a scene
function appears.

AUTO

Use auto settings

Toggle the SET button left, right, up
or down to select the desired
setting.

Scene function

Features

Recording mode setting
s

Enhance the threedimensional feel of the
subject by blurring the
background. (With face
chaser function)

\
Landscape

For beautiful shots of distant
scenery.

]
Night view
portrait

Photograph the subject while
keeping the background
night scenery.

n
Smile detection

Capture a photo at the
instant the subject smiles.

H
Fireworks

For capturing fireworks at
night.

X
Auto

The camera makes the
optimum settings.

Y
Sports

Capture a split-second image
of a fast-moving subject.

G
Portrait

English

Scene function

Recording mode setting

Features

Four successive still images
are captured as the exposure
changes.

=
Panorama

Three images are captured
to create a panorama photo.

r
Face chaser

The subject’s face is kept in
focus and the exposure adjusted
as the image is captured.

8
Monochrome

Create black-and-white
photos.

9
Sepia

Create sepia-tone photos.

@
Vivid

Accentuates the colors in the
image.

_
Lamp

Photograph in low-light
conditions.

a
Still image with
audio

Shoot a still image and add a
voice memo.

5
Best shot

m: Available n: Not available
*
: Disabled during recording

Press the SET button.
h This completes the scene select
setting.
h The display returns to the Shooting
Screen.
h The scene function setting is shown
on the monitor.

Scene function setting
(X is not displayed)

English

USING THE SCENE FUNCTION
Capture a still image with a voice memo
With the still-image-plus-audio a scene function, you can add an audio
track (about 10 seconds maximum) to a captured still image. This audio track
is called a “voice memo”.

1
2

On the screen to select a scene function (page 41), select a, and
press the SET button.
Press the shutter button to take the
picture, then speak into the
microphone.
h During recording, be careful not to
obstruct the microphone with your
fingers, for example.
h Audio recording begins. During
recording, the length of the audio
track and the remaining recording
time available are shown on the
monitor.
h The maximum recording time for a
voice memo is about 10 seconds.
h To end the recording before
10 seconds has elapsed, press the
shutter button.

English

Recorded length of
audio track
Remaining recording time
available

00:00:02
00:00:08

How to use the best shot feature

1
2

Set the camera to the single-shot mode; on the screen to select a
scene function (page 41), select 5; and press the SET button.
Press the shutter button.
h While the settings change, four still
images are shot in sequence.
h After the images are captured, the
four still images are displayed on
the monitor.

h With all four images showing on the
monitor, press the MENU button.

SELECT

SAVE ALL

Toggle the SET button left, right, up or down to move the orange
frame to the image you wish to save.
h For a full-size view of the selected image, press the SET button.
h With the full-size view active, you can toggle the SET button to the left
or right to view the previous or next image.
h To return to the screen in step 2, press the MENU button.
With the full-size view of the image
you wish to save, select “YES”, and
press the SET button.
h The image currently displayed is
saved, and the other images are
deleted.

Delete other images?

YES
EXIT
SET
OK

HINT
i When the resolution is set to <, the j compression rate is not
available.

English

USING THE SCENE FUNCTION
How to create a panorama photo

Set the camera to the single-shot
mode, display the screen to select a
scene function (page 41), select
=, and press the SET button.
h The screen to select a panning
direction appears.

149

SET Select record method

2
3

Toggle the SET button left or right to select the desired panning
direction, and press the SET button.
h The screen to shoot the first image appears.
Press the shutter button to capture
the image.
h The screen to shoot the second
image appears.
h Positioning lines (red and black)
appear on the screen to mark
where the images will be joined.
h When the SET button is pressed,
the captured image is saved.

Red line

Black line

SET

English

Move the camera in the panning
direction you selected in step 2.
h One of the positioning lines (black)
moves as you reposition the
camera.

Line up the black line with the red
line.
h Match the lines exactly.
h When the lines match exactly, the
line changes to green.

Red line

Black line

Changes to green

The shutter releases automatically when the lines match.
h Position the camera for the third image in the same way.
h To create a panorama photo from two images, after capturing the
second image, press the SET button.
The shutter releases automatically when the lines match.
h When the third image is captured, the three images are combined and
saved.

HINT
i The digital zoom is not available.
i The flash and self-timer cannot be used.

English

USING THE SCENE FUNCTION
How to use the face chaser feature
To attain the best possible face shots, the camera automatically focuses on
the face and adjusts the exposure.

1
2

3
4

On the screen to select a scene function (page 41), select r, and
press the SET button.
Aim the camera lens at the subject.
h The camera searches for the
subject’s face. When it detects the
face, a green frame appears.
h Do not touch the shutter button while
the camera is searching. The
camera cannot search when the
autofocus is activated.

Green frame

1432

The focus locks on the subject (page 26).
h The camera focuses on the subject and the exposure is adjusted.
h When the face is in focus, the green frame changes to orange.
Press the shutter button.
h The image is captured.

CAUTION
i The digital zoom is disabled.
i The face chaser function does not work when zooming in or out.
i The face chaser function may not work when the subject’s face in the
monitor is relatively small or appears dark.
For images captured using the face chaser feature
i On the Playback Screen, when zooming in, the face that was defined by
the double frame during capture becomes the zoom center.

English

How to shoot using Smile Detection
Capture a photo at the instant the subject smiles.

Normal shooting

1
2

On the screen to set the scene function (page 41), select n, and
press the SET button.
Aim the camera lens at the subject.
h The camera searches for the subject’s face. When it detects the face,
a green frame appears. The image is automatically captured when the
subject smiles.

Selecting the shooting area of the desired subject
From the multiple faces, select the area that frames the targeted face, and
capture the image when the selected subject smiles.

1
2
3

On the screen to set the scene function (page 41), select n, and
press the SET button.
Aim the camera lens at the subject.
Press the SET button.
h An orange frame appears, and the screen for you to select the area
that encompasses the target subject’s face appears.

English

USING THE SCENE FUNCTION

4
5

Toggle the SET button left, right, up or down to move the orange
frame to the area that encompasses the target subject’s face.
Press the SET button.
h The orange frame changes to yellow, and the Smile Detection area is
fixed.
h The camera adjusts the focus and exposure for the framed face.
h When the face is in focus, the green frame changes to a double frame.
h The image is automatically captured when the subject in the selected
area smiles.

HINT
The camera can’t detect the smiling face?
i The camera cannot detect the subject’s smile when zooming in or out.
i Smile Detection may not work accurately when the face in the monitor
appears small or dim.
For best results with Smile Detection
i Smile Detection works best when the subject is directly facing the camera
and showing his/her teeth when smiling.
Can’t use the self-timer?
i The self-timer cannot be used with Smile Detection.
To cancel Smile Detection...
i Select a different scene function.

English

OTHER RECORDING FUNCTIONS
Using the zoom
Your camera has two zoom functions: optical zoom and digital zoom.

1
2

Set the camera to the recording
mode (page 21), and point the
camera lens at the subject.
Press the zoom switch to
compose the desired image.
[T]: Zoom in on the subject.
[W]: Zoom out.
h When the zoom switch is
pressed, the zoom bar appears
on the monitor.
h When the optical zoom factor is
at maximum, zooming stops
temporarily. When [T] on the
zoom switch is pressed again,
the mode changes to the digital
zoom mode and zooming
continues.
Take the picture.

Zoom switch [W]/[T]

When both optical
and digital zoom
are enabled

Zoom bar
Pointer

Optical zoom
Digital zoom (yellow)
When optical zoom
only is enabled

English

OTHER RECORDING FUNCTIONS
HINT
Can’t access the digital zoom?
i The digital zoom cannot be used when the face chaser r, smile
detection n or portrait mode G scene function is active, or the focus
mode is set to AF seeker p.
Can’t access the optical zoom?
i When the focus range is set to pan o or during video clip recording, the
optical zoom cannot be used.

English

Flash setting
The flash is used not only for taking pictures where there is insufficient light,
but also when the subject is in shade or in backlight conditions. Your camera’s
flash has four modes of operation (auto mode, forced flash mode, flash off
mode and red-eye reduction mode). Select the flash mode that is appropriate
for the surrounding conditions. The flash can be enabled only when taking
single-shot still images.

Set the camera to the single-shot
mode (page 22), and toggle the
SET button up.
h The flash menu appears.

SET button

k: The camera will detect the
subject brightness and use the
flash only when required. In a
backlight situation, if only the
center of the image is very dark,
the flash will operate to
compensate (auto).
m: The flash will operate with every
image captured regardless of the
conditions. Use this setting
under backlight conditions, when
the subject is in shade, under
fluorescent lighting conditions,
etc. (forced flash).
l: The flash will not operate even in
FLASH
dark situations. Use this setting
AUTO
when capturing an image in a
location where flash
photography is prohibited, or
when shooting a night landscape
Flash menu
scene (flash off).
J: The digital camera will detect the subject brightness and use the
flash only when required. At this time the flash will operate in a
manner that reduces the red reflection (“red-eye”) in the subject’s
eyes (red-eye reduction).

English

OTHER RECORDING FUNCTIONS

2
3

Toggle the SET button up or down to select the desired flash mode,
and press the SET button.
Press the shutter button.
h The picture is snapped and the flash operates according to the
selected mode.

HINT
When auto is selected...
i The k icon indicating the flash setting is not shown on the Shooting
Screen.
When auto or red-eye reduction is selected...
i When the shutter button is pressed, if the camera determines that the flash
is necessary, a k or J icon appearing on the monitor indicates that
the flash will operate.

English

Self-timer
Self-timer photography is available in the single-shot mode.

Set the camera to the single-shot
mode (page 22), and toggle the
SET button to the left.
h The self-timer menu appears.

SET button

y: The image is captured about
2 seconds after the shutter
button is pressed.
x: The image is captured about
10 seconds after the shutter
button is pressed.

Toggle the SET button up or
down to select the desired selftimer setting, and press the SET
button.
h The self-timer is set, and you are
returned to the Shooting Screen.
1
PHOTOGRAPH 1 IMAGE

Self-timer menu

English

OTHER RECORDING FUNCTIONS
HINT
i The countdown time until shutter
release is shown graphically on the
monitor.

To pause or cancel the self-timer function...
i If the shutter button is pressed again before the shutter is released, the
self-timer countdown temporarily stops. Press the shutter button one more
time to restart the self-timer.
i To cancel self-timer photography, set the self-timer setting to off s.
i After the self-timer picture is snapped, the self-timer is automatically reset
to off.
When x is selected...
i When the shutter button is pressed,
the self-timer indicator flashes for
approximately 10 seconds, after
which shooting begins.
i About 3 seconds before shooting,
the self-timer indicator flashes
faster.

English

Self-timer indicator

Focus range

Set the camera to the recording
mode (page 21), and toggle the
SET button down.
h The focus range menu appears.

SET button

o: The focus operates within the
ranges shown below (pan).

i 2.5 m (8.20 ft.) to ∞

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2010:01:18 10:07:16Z
Creator Tool                    : FrameMaker 7.2
Modify Date                     : 2010:01:18 10:30:17+09:00
Metadata Date                   : 2010:01:18 10:30:17+09:00
Format                          : application/pdf
Title                           : 
Creator                         : .
Document ID                     : uuid:ebd1eda4-eb73-48cb-bde7-0d37bf3edfa5
Instance ID                     : uuid:ceb3ac61-42ac-4f1c-b954-7144e114f68f
Page Count                      : 84
Page Layout                     : TwoPageRight

EXIF Metadata provided by EXIF.tools

Sanyo Vpc X1400 Instruction Manual

VPC-X1420 GX - Instruction Manual VPC-X1400_X1420 Free User Guide for Sanyo Camera, Manual

Navigation menu

Versions of this User Manual:

Views

Navigation