Sargent Instructions For Installing 351 Series Door Closers With 'UH/HZ/HZA/PH9' Holder Arms A7341A
User Manual: Sargent Instructions for Installing 351 Series Door Closers with 'UH/HZ/HZA/PH9' Holder Arms Instruction Sheets
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
MODEL 351 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH "H" HOLDER ARMS 351 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE. FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477. 1 STANDARD & TOP JAMB APPLICATIONS STANDARD APPLICATION (TYPE 25-H ARM) USE PAGE 2 CLOSER MOUNTED ON HINGE SIDE OF DOOR DOOR WIDTH (INCHES) 24 30 32 36 40 42 44 46 48 OVER 48 NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREW FROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORS APPROXIMATE EXTERIOR DOORS DOOR WEIGHT (POUNDS) FACTORY SET 80 110 1-4 CW 115 1-5 CCW 130 4-7 CW 150 155 7-10 CW FACTORY SET 165 170 1-5 CW 10-12 CW 180 UP TO 18 CW AS REQ. 5 CW AND UP AS REQ. ADJUST SPRING POWER ACCORDING TO CHART* NOTE: FOR H8 ARM MOUNTING SEE DATA SHEETS ENCLOSED TOP JAMB APPLICATION (TYPE 25-H, 25-HZ, 25-HZA) + USE PAGE 3 - INCREASE POWER DECREASE POWER CLOCKWISE (CW) COUNTER CLOCKWISE (CCW) 5/8" SPRING POWER ADJUSTMENT NUT LEFT HAND DOOR PULL HINGE SIDE STOP (PUSH) SIDE CLOSER MOUNTED ON FRAME ON STOP SIDE OF DOOR PULL HINGE SIDE RIGHT HAND DOOR STOP (PUSH) SIDE PARALLEL APPLICATION ONLY PARALLEL ARM APPLICATION (TYPE 25-PH9) USE PAGE 4 CLOSER MOUNTED ON STOP SIDE OF DOOR DOOR WIDTH (INCHES) 24 30 32 36 40 42 44 46 48 OVER 48 NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT FROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORS APPROXIMATE DOOR WEIGHT (POUNDS) EXTERIOR DOORS 80 2-6 CW 110 115 6-8 CW 1-5 CCW 130 150 FACTORY SET 8-11 CW 155 165 170 180 11-13 CW 1-7 CW UP TO 18 CW AS REQ. 8 CW AND UP AS REQ. ADJUST SPRING POWER ACCORDING TO CHART* *IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS ARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING SPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW COUNTERCLOCKWISE. Copyright © 2007, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. A7341A 1 351 STANDARD APPLICATION INSTRUCTIONS IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING ARM TYPE MOUNTING MAX. DOOR OPENING DIM. A DIM. B DIM. "B" “H” HOLDER ARM STANDARD 110 9 1/2" 12 3/4" ALTERNATE 160 6 1/2" 9 3/4" DIM. "A" 1 1/8" 2 1/2" TOP OF DOOR IF BUTT, FRAME AND WALL CONDITIONS PERMIT DOOR WILL OPEN 180° 1 2 RIGHT HAND DOOR SHOWN. LEFT HAND DOOR OPPOSITE. 2 1/2" 9/16" THIS DIMENSION IS TAKEN FROM HINGE EDGE OF DOOR FOR INVISIBLE HINGES. 9" DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. SEE PAGE 6 FOR MORTISE NUTS. #12 x 3 WOOD SCREWS OR #12-24 X 2 1/4 FLAT HEAD MACHINE SCREWS CL OF HINGE PIVOT: BUTTS, OFFSET PIVOTS, SWING CLEAR, CENTER HUNG OR INVISIBLE HINGES A INSTALL DOOR CLOSER TO DOOR WITH SPRING ADJUSTMENT NUT AWAY FROM HINGE. NOTE: 351 CLOSER BODIES ARE NON HANDED. IT IS IMPORTANT THAT THE CLOSER BODY BE MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT HAND DOORS. RH RIGHT HAND DOOR SHOWN ATTACH FOOT TO FRAME AS SHOWN WITH NUT UP FOR RH DOOR OR DOWN FOR LH DOOR. C ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW. NUT FACES UP MAIN ARM 3 1 POSITION OF MAIN ARM WHEN ASSEMBLING TO SPINDLE 5 HOLD OPEN ARM RIGHT HAND DOOR LEFT HAND DOOR 4 RIGHT HAND DOOR 2 B ARM SCREW 90° INDEX MARK ON SPINDLE ROD NUT FACES DOWN Copyright © 2007, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. A7341A 2 351 TOP JAMB APPLICATION INSTRUCTIONS ARM TYPE REVEAL DEPTH DOOR OPENING “H” ARM 0" TO 2" 140 “HZ” ARM 2 1/8" TO 5" 140 “HZA” ARM 5 1/8" TO 8" 140 1 RIGHT HAND DOOR SHOWN, LEFT HAND DOOR OPPOSITE. 3 THIS DIMENSION IS TAKEN FROM HINGE EDGE OF DOOR FOR INVISIBLE HINGES. 4 DOOR OPENING TO 180 IS POSSIBLE IF DEPTH OF REVEAL IS NOT GREATER THAN 2" DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. SEE PAGE 6 FOR MORTISE NUTS. 5 3/8" 2 1/8" 9" 1 1/2" 2 1/2" SINGLE RABBETED FRAME 6" 3 3/8" 1" MOUNTING PLATE 13/16" FRAME DOOR 351-A TOP OF DOOR DEPTH OF REVEAL 2 5/16" 7/16" 1" 8 7/8" CL OF PIVOT HINGE #12 X 1 1/2" WOOD SCREWS OR #12-24 X 5/8" FLAT HEAD MACHINE SCREW 2 1/2" 351-A MOUNTING PLATE REQUIRED FOR DOUBLE RABBETED DOOR. 3 3/8" 1" 1 3/4" MIN. 1" C L OF PLATE MOUNTING SCREWS 7/16" DEPTH OF REVEAL DOUBLE RABBETED FRAME WITH REQUIRED 351-A MOUNTING PLATE A INSTALL DOOR CLOSER TO FRAME/MOUNTING PLATE WITH SPRING ADJUSTMENT NUT AWAY FROM HINGE. B NOTE: 351 CLOSER BODIES ARE NON HANDED. IT IS IMPORTANT THAT THE CLOSER BODY BE MARKED WITH “RH” SYMBOL AT TOP, FOR LEFT HAND DOORS. “LH” SYMBOL AT TOP FOR RIGHT HAND DOORS. ATTACH FOOT TO DOOR WITH NUT UP FOR LH, DOWN FOR RH NUT FACES UP LH RIGHT HAND DOOR SHOWN RIGHT HAND DOOR RIGHT HAND DOOR NUT FACES DOWN C INSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN. INSERT ROD END INTO MAIN ARM AND TIGHTEN ARM SCREW. ARMS ARE HANDED AND MUST BE THE SAME HAND AS DOOR. LEFT HAND DOOR RIGHT HAND DOOR 1 5 POSITION OF MAIN ARM WHEN ASSEMBLING TO SPINDLE 90° INDEX MARK ON SPINDLE 2 3 ARM SCREW MAIN ARM HOLD OPEN ARM ARM SCREW 90° 4 HOLD OPEN ARM ROD VIEW LOOKING UP WHEN ASSEMBLING ARM TO SPINDLE ROD Copyright © 2007, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. POSITION OF MAIN ARM WHEN ASSEMBLING TO SPINDLE A7341A 3 351 PARALLEL ARM APPLICATION INSTRUCTIONS DIM. A MAX. DOOR OPENING C OF L HINGE PIVOT (BUTT HINGE SHOWN) DIM. B 2 1/2" 5/16" 120 9 7/8" 10 1/4" 180 7" 7 3/8" #12 WOOD SCREWS OR #12-24 x 5/8 FLAT HEAD MACHINE SCREWS 1 1/4" DOOR TOP VIEW 1/2" LEFT HAND DOOR SHOWN. RIGHT HAND DOOR OPPOSITE. 1 7/8" DIM. B DO NOT USE THIS MOUNTING FOR “SWING CLEAR” HINGES. 2 TOP OF DOOR DIM. A THIS DIMENSION IS TAKEN FROM HINGE EDGE OF DOOR FOR INVISIBLE HINGES. 3 2 3/8" DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. SEE PAGE 6 FOR MORTISE NUTS. STOP 2 1/2" #12 x 3 WOOD SCREWS OR #12-24 X 2 1/4" MACHINE SCREW 9" C OF L HINGE PIVOT A B INSTALL DOOR CLOSER TO DOOR WITH SPRING ADJUSTMENT NUT AWAY FROM HINGE. ATTACH FOOT BRACKET TO FRAME STOP AND MOUNT HOLD OPEN ARM TO BRACKET WITH ADJUSTING NUT FACING DOWN FOR LEFT HAND, FACING UP FOR RIGHT HAND DOOR. RIGHT HAND DOOR SHOWN RH NOTE: 351 CLOSER BODIES ARE NON HANDED. IT IS IMPORTANT THAT THE CLOSER BODY BE MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT HAND DOORS. NUT FACES DOWN NUT FACES UP USING WRENCH ON BOTTOM END OF SPINDLE, ROTATE SPINDLE 45 AND ASSEMBLE MAIN ARM TO CLOSER AS SHOWN, AND THEN INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW POSITIONING ARM 1/2" AWAY FROM DOOR. INDEX MARK ON SPINDLE INDEX MARK ON SPINDLE 45° 2 PRELOAD APPROX. 45° OPTIONAL FOOT BRACKET FLUSH TRANSOMS. SEE DATA SHEET ENCLOSED. PH4 BRACKET 4 1 45° 2 MAIN ARM 5 3 5 1 RIGHT HAND DOOR SHOWN RIGHT HAND VIEW OF INDEX LEFT HAND VIEW OF INDEX 3 C LEFT HAND DOOR SHOWN POSITION OF MAIN ARM WHEN ASSEMBLING TO SPINDLE 4 MAIN ARM CAUTION: DOOR CLOSER WILL NOT OPERATE PROPERLY IF ARM IS NOT INDEXED CORRECTLY. RIGHT HAND DOOR 1/2" LEFT HAND OPPOSITE MAIN ARM SWIVEL ARM HOLD OPEN ARM ARM SCREW FOOT BRACKET Copyright © 2007, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. A7341A 4 FINAL ADJUSTMENT AND REGULATING PROCEDURE BACKCHECK VALVE OPTIONAL DELAYED ACTION VALVE DELAYED ACTION RANGE DOOR SPEED VALVE CLOSING SPEED RANGE BACKCHECK RANGE LATCHING SPEED VALVE A LATCHING SPEED RANGE B REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED. USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR MOVEMENT. FASTER (+) C TO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVE CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE CHECKING. CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT IS DAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT. NEVER USE BACKCHECK AS A DOOR STOP. ALWAYS USE A DOOR STOP TO STOP THE DOOR. SLOWER (–) FOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE REGULATING BACKCHECK D “DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGH DELAYED ACTION RANGE TURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR MOVEMENT ADJUSTMENT OF HOLD OPEN ARM. SLIGHT TIGHTENING OR LOOSENING OF HOLD OPEN NUT CHANGES HOLDING POSITION OF DOOR. NOTE: TO PROTECT WALL, TRIM AND CLOSER, USE A DOOR STOP LOCATED 10 BEYOND HOLD OPEN USE 15/16" POSITIONS BUT NOT WRENCH TO ADJUST BEYOND THE MAX. NUT DOOR OPENING SHOWN ON INSTRUCTIONS. HOLD OPEN NUT E INSTALL COVER WITH TWO SCREWS AS SHOWN. INSERT IS REMOVABLE. PLACE IN UNUSED OPENING. Copyright © 2007, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. A7341A 5 USING MORTISE NUTS WITH SARGENT DOOR CLOSER 1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODY AND FOOT ON DOOR AND FRAME. 2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR. 3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT SHOWN FOR MOUNTING THE CLOSER BODY. 4. FOR DOORS 2 1/4" THICK: MORTISE NUT SHOWN FOR 1 3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS. DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTS ARE TIGHTENED. SARGENT 1430 SERIES CLOSER SHOWN. (OTHER SERIES SIMILAR) SEE NOTE #1 BELOW FOR DIMENSION INFORMATION. IF A DIMENSION LESS THAN 7/8" IS USED. THE DOOR STOP MUST BE CUT TO CLEAR THE MORTISE NUT HEAD OR THE MORTISE NUT HEAD MUST BE RECESSED. (SEE ENLARGED VIEW "Y") FRAME DOOR STOP COVER MORTISE NUT HEAD DOOR DRILL 3/8" DIA. HOLE FOR MORTISE NUT BODY. DRILL 1/4" DIA. HOLE FOR MOUNTING SCREWS 1/8" SHORTEN MORTISE NUT BODY TO THIS LENGTH 5/8" DIA. HOLE FRAME DOOR STOP DOOR 351 DOOR CLOSER SHOWN (TRACK ASSEMBLY MOUNTING IS SIMILAR) 1/4" DIA. DRILLED HOLE #12-24 THREAD MORTISE NUT MORTISE NUT HEAD 3/8" DIA. HOLE 9/16" DIA. 7/64" 1 11/16" FOR 1 3/4" THICK DOOR 1 5/16" FOR 1 3/8" THICK DOOR (SEE NOTE #4 FOR 2 1/4" THICK DOORS) Copyright © 2007, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. A7341A 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 6 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments Creator : QuarkXPress(R) 7.31 Modify Date : 2008:07:03 08:53:01 Create Date : 2008:07:03 08:53:01 Producer : QuarkXPress(R) 7.31 Title : Layout 1EXIF Metadata provided by EXIF.tools