Satellite Electronic 18003 CEILING FAN REMOTE CONTROLLER User Manual TR256A MR181A AC120V FCC

Download:
Mirror Download [FCC.gov]
Document ID	4177022
Application ID	FQeC/lL299F7eWro4FTO0w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.49kB (156166 bits)
Date Submitted	2019-02-22 00:00:00
Date Available	2019-02-22 00:00:00
Creation Date	2019-01-03 14:45:22
Producing Software	Ultra PDF
Document Lastmod	2019-01-03 14:45:22
Document Title	TR256A+MR181A AC120V FCC.doc
Document Creator	TR256A+MR181A AC120V FCC.doc - WPS 2019
Document Author:	USER

CEILING FAN REMOTE CONTROLLER
OPERATION AND INSTALLATION INSTRUCTIONS
(Please keep this instruction pamphlet.)
IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT
KIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1. Read and save these instructions.
2. Please note that all fixed wiring appliances should be installed by a qualified electrician.
3. The supply to the remote control receiver should be connected through a mains switch, i.e.
existing wall switch.
4. Disconnect from power supply at wall switch before working on remote control receiver or
ceiling fan.
5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6. This unit is to be used for the control of ceiling fan and in an AC110V/120V 60Hz power
supply only.
7. Do not install in damp locations or immerse into water. (For indoor use only.)
8. Do not pull on or cut leads shorter.
9. Do not drop or bump the unit.
10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking
takes place as this will damage the transmitter. Dispose of used battery properly, keep the
battery out of reach of children.
11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any
variable (rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the
“Pull Switch” after installation.
2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket.
The canopy comes up to cover the receiver and bracket.
LEARNING PROCESS
1. After installing the unit and power on, open battery cover (with
batteriy, DC3V/CR20321pc, installed), press remote’s LEARN
key to control ceiling fan for learning process. Please note that
press any button within 1 minute after power on. If just replace
batteries, no need to re-learn.
2. Please note that the transmitter can learn in multiple receiver,
when doing learning process please make sure not learn in other
receiver.
CHANNEL SETTING
0: All handsets and receivers are factory pre-set to the same channel. You can operate the fan without
doing a channel setting above but we recommend that you set an individual channel for your fan.
1: This is to allow for each handset and receiver to be set on an individual channel.
LIGHT FUNCTION SELECT SWITCH
If installed energy light onto ceiling fan, please set the “light function select switch” “light function select switch” to
on/off position,” O”. If installed tungsten light onto ceiling fan, please set the “light function select switch” to dimmer
position,” D”.
FUNCTIONS OF TRANSMITTER
:Turn on the fan at high speed
: Turn on the fan at medium speed
: Turn on the fan at low speed
: Turn off the ceiling fan.
ON/OFF- Press and release immediately to turn on or off the light
DIMMER- Press and hold on to dimmer or brighten the light. (For the tungsten bulb and “light function select
switch” is at D position.)
Installation of transmitter wall
mount holder with two screws.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult
the dealer or an experienced radio/TV technician for help.
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority
to operate the equipment.
FCC ID：2AQZU-18003
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Modify Date                     : 2019:01:03 14:45:22+08:00
Create Date                     : 2019:01:03 14:45:22+08:00
Title                           : TR256A+MR181A AC120V FCC.doc
Author                          : USER
Creator                         : TR256A+MR181A AC120V FCC.doc - WPS 2019
Producer                        : Ultra PDF

EXIF Metadata provided by EXIF.tools