Schlage Electronic Security VIP Door Lock User Manual 57032 A

Schlage Electronic Security Door Lock 57032 A

Manual

Form 57032 Rev. A 01-05-2004VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUAL5100 CYLINDRICALLOCKSET - STANDARDThe VIP 5100 series lock is a microprocessor controlled, electromechanical locking system.It is an open architecture product designed to interface with 3rd party panels ecompassingall the features of the lock, reader, door status* and egress (rex/request to exit) indication inone fire-rated piece of hardware. The 5100 employs a heavy-duty mechanical design testedand complying with ANSI/BHMA grade 1 standards for performance and reliability. It is pow-ered by 12 or 24 volts DC with only four wires required - two for power and two for commu-nications. The lock communicates with a PIB (panel interface board) which communicateswith the panel as if it were separate components of an access control system.Operationally, the outside lever is normally locked and the inside lever always retracts thebolt to allow egress. Electronic access control is achieved by entering an”Access Credential”(magnetic stripe card or Prox fob or card). The panel controls the lock through the PIB.*Cylindrical model requires separate door status switch (included) to be installed in the doorand frame and connected to the VIP lock.Please refer to all instruction manuals involved in the installation before you begin. Functions:VIP 5196-FSA: Cylindrical, Fail Safe (unlocked)VIP 5196-FSE: Cylindrical, Fail Secure (locked)Models:MG: Magnetic stripe card readerPX: HID Prox card readerStandard Monitoring Switches:DSM: Provides door status via data link to panel interfaceKSM: Provides mechanical key use events via data link to panel interfaceREX: Provides indication of inside lever use for request to exit input via data link to panel interfaceOptions:T3: Track 3 card reader (data must be ABA track 2 format) - MG onlyEXT: exterior use option - MG only (PX model has this standard)KD: Keyed Different, includes Schlage Everest cylinderKA: Keyed Alike, includes Schlage Everest cylinderLC: Less CylinderSLB: 2-3/4” backset, 1/2” latch boltOLB: 2-3/8” backset, 1/2” latch boltELB: 2-3/4” backset, 3/4” latch boltBEFORE YOU BEGIN:Standard units are shipped from the factory to fit 1-3/4” doors. Verify thedoor thickness. If the door is not 1-3/4” thick, verify that the door thicknessoption was ordered or consult factory.PRE-INSTALLATION CHECK:AN OPEN ARCHITECTURE SYSTEM REQUIRES AT LEAST THREE COMPO-NENTS - A PANEL INTERFACE BOARD (PIB), AN ACCESS CONTROL PANEL(BY OTHERS) TO WHICH THE PIB IS CONNECTED AND THE VIP LOCK. SEEDOCUMENTATION FOR THE ACCESS CONTROL PANEL/SOFTWARE THISLOCK WILL BE USED WITH FOR ANY PRE-INSTALLATION TESTING REQUIRE-MENTS AND REMEDIES. REFER TO THE WIRING INFORMATION INCLUDEDWITH THE PIB FOR MORE INFORMATION.PIBPX MGDoor Thickness Kits:Available in 1/8” increments from 1-3/8” to 2-1/2”This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device maynot cause harmful interference, and (2) this device must accept any interference received, including any interference that maycause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate the equipment.
Form 57032 Rev. A 01-05-20042VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUALWIRE RACEWAY REQUIRED:It is best to have the wire race way prepared at the door andframe manufacturer. If this has not been done there are twosuggested preparation methods for making wire paths for theFSE and FSA models in the field. Select method A or B;depending on the door and frame circumstances, one may bebetter than the other. Consult door manufacturer with any ques-tions regarding agency listings with respect to fire integrity.METHOD A:1. Prep door and frame according to standard template.2. Determine location of standard 1 inch wire harness throughhole and mark centerline of hole on hinge side of door.3. Using appropriate drilling jig and drill bits, drill 3/8” or 1/2”wire race from edge of hinge side into standard wire harnessthrough hole.4. Install electric hinge or door cord and run wires.METHOD B:1. Prep door and frame according to standard template.2. Using a 1” drill bit, continue the 1” latch hole through retractorhole to a depth of 5”. This will allow room for the wiring to passaround the retractor.3. Using appropriate drilling jig and drill bits, drill 3/8” or 1/2”wire race from the latch hole through the door toward the hingeside. It is not necessary to continue drilling the hole through thehinge side.4. Measure up 3 inches from the center of the 2 1/8” retractorhole and drill a 1 inch through hole on center as shown below.5. Using a 3/8 inch drill bit, place the tip of the drill into the 1”wire hole drilled in step 3 and aim at the angles shown. Drilldown and toward the hinge side to intersect the 1” latch hole(where it was continued in step 2.4. Install electric hinge or door cord andrun wires.Note: this method offers the advantage ofnot having holes exiting the door edges.If a door cord is used the door cord wirehole can be cross drilled into the longwire race.WIRE RACEWIRE RACESTANDARD WIREHARNESS THROUGHHOLEMETHOD B:METHOD A:FSE & FSA HARD WIRED MODELSREQUIRE WIRING TO BE RUN TOTHE LOCK PREP FROM THE HINGESIDE. BELOW IS A SUGGESTEDMETHOD TO DO THIS. A DOOR CORDOR ELECTRIC HINGE OR POWERTRANSFER DEVICE IS USED TOROUTE WIRING FROM FRAME TODOOR. NOTE THAT WHEN USING ANELECTRIC HINGE IT IS RECOM-MENDED THAT THE POWER WIRESBE DOUBLED OR TRIPLED UP (ONBOTH THE POSITIVE AND GROUNDLEGS) TO AVOID SIGNIFICANT VOLT-AGE DROP THROUGH THE THINWIRES IN THE HINGE.
Form 57032 Rev. A 01-05-20043VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUAL1. PREP DOOR AND FRAME:A. Determine door hand and correct backset.B. Mark the horizontal and vertical centerlines for the lockset, latch and strike.C. Place template on inside of door (opposite the side that the keypad/reader will be on). Line up the correct reference lineson the template with the edge of the door. The centerline on the door should line up with the vertical centerline of the tem-plate.D. Drill holes as described by template.DOOR EDGE (LATCH) FRAME (STRIKE)DOOR FACE (LAY OUT ON INSIDE)
Form 57032 Rev. A 01-05-20044VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUAL2. INSTALL CYLINDER (IF NOT ALREADY DONE), GASKET AND STANDOFFS:A. Install cam onto cylinder (if not already done.) Cam must be a straight 11/16” design. See below for recommended cams.B. Insert mortise cylinder into outside escutcheon from front (keypad/reader) side with keyway down.C. Slide lock washer onto cylinder (tab on top facing out, as shown below.)D. Using nut tool (provided) tighten nut onto cylinder.E. Line up nearest notch on nut with tab on lock washer and bend tab using nut tool so nut is secure. F. Install exterior gasket (if used).G. Install standoffs.TEST KEY OPERATION NOW: Turning key clockwise until it stops (about 1/2 turn) should allow the lever to turn retractor.CYLINDERRECOMMENDED CAMS:SCHLAGE EVEREST: P/N B502-948SCHLAGE CLASSIC: P/N B502-191NUT TOOLRETRACTOR ASSEMBLYLOCK WASHERNUTSTANDOFFSEXTERIOR GASKETTABNOTE:BLOCKING RING REQUIRED FOR CYLINDERLENGTH GREATER THAN 1-1/8”.THICKNESS = CYLINDER LENGTH - 1 1/8”
Form 57032 Rev. A 01-05-20045VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUAL3. CHANGE HAND (IF NECESSARY):NOTE: The locks are shipped handed as ordered from factory. follow the steps below to reverse the handing:A. Remove retractor by loosening two 9/64” socket cap screws which attach it to the outside escutcheon.B. Remove outside spindle.C. Loosen 5/32” socket cap screw which secures handle to escutcheon.D. Remove, rotate and re-install handle (NOTE: some handle designs have an adapter.)E. Re-install outside spindle, making sure that the round end faces the handle, and the spindle is positioned with its edgesvertical and horizontal as shown in detail below. Note that the cam (inside the escutcheon assembly) must be positionedsuch that the dot on it faces the 6 O’Clock position (see detail below).F. Rotate retractor and re-install it.G. Change the hand of the handle on the inside escutcheon (not shown) the same way. Note that the inside escutcheon hasno retractor.OUTSIDE ESCUTCHEONOUTSIDE SPINDLE(ROUND SIDE TOWARD LEVER)9/64” SOCKET CAPSCREW5/32” SOCKET CAPSCREWRETRACTOROUTSIDE HANDLEDOT - FACESDOWNOUTSIDESPINDLEPOSITIONCAMDETAIL
Form 57032 Rev. A 01-05-20046VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUAL4. INSTALL STRIKE BOX, STRIKEAND DOOR SWITCH MAGNET:5. INSTALL LATCH AND DOOR STATUS SWITCH:A. Install latch into edge of door. Be sure to install it with the beveled edge facing door jamb.B. Install switch as shown, passing switch wires through to the inside of the door.
01-05-20047VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUALForm Form 57032 Rev.DETAILProngs on latch mustengage with retractor.6. INSTALL OUTSIDE ESCUTCHEON ASSEMBLY:A. Remove latch guard from retractor.B. If the door is less than 1-3/4” thick, install spacer plate provided.C. Install outside escutcheon onto door (see detail for latch engagement). Pass wiring harness through wire hole.D. Re-install latch guard onto retractor.7. INSTALL INSIDE BASEPLATE ASSEMBLY:SPACER(FOR DOORS LESS THAN 1-3/4”)SPACER(FOR DOORS LESS THAN 1-3/4”)SOCKET CAP SCREW,WASHERSDATA/POWER WIRES COMEFROM HERE IF WIRINGMETHOD “B” WAS USED.PASS THE WIRES THROUGHTHIS HOLE. (IF A SPACER ISUSED DRILL A HOLE IN THESPACER PLATE FOR WIRES TOPASS THROUGH.)OUTSIDE ESCUTCHEONWIRING HARNESSLATCH GUARDPHILLIPS HEADSCREWS
Form 57032 Rev. A 01-05-20048VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUALFIELD WIRING FROMPANEL AND POWERSUPPLY.DOOR SWITCHREX INPUT(PLUG IN WHEN INSIDEESCUTCHEON ISINSTALLED)8. MAKE WIRING HARNESS CONNECTIONS :A. Plug MAIN WIRING HARNESS into PC board.B. Plug MAKE FIELD CONNECTIONS TO TERMINAL BLOCK.C. Pug in DOOR STATUS SWITCH as shown.D. Verify correct lock type setting (FSE/FSA) - see dip switch setting. Note: as ordered from the factory.E. If lock is the one farthest away from PIB set termination resistor to “on”. All others should be in the “off/parked” position.F. Test operation of inside lever to make sure that latch retracts fully.IMPORTANT! See PIB manual for additional connecting instructions.SHIELDDATA BDATA AGROUNDV+ 1.0A @ 12VDC0.5A @ 24VDCOUTSIDEMAIN HARNESSCONNECTION OFF(PARKED)ONTERMINATIONRESISTOR:1: LOCK ADDRESS (SEE CHART)2: LOCK ADDRESS (SEE CHART)3: ALWAYS SET TO OFF4: ALWAYS SET TO OFF5: OFF = FAIL SECURE (FSE)ON = FAIL SAFE (FSA)6: OFF = ALL MG LOCKSON = ALL PX LOCKS7: NOT USED8: NOT USED9: NOT USED10: NOT USEDLOCKADDRESS1LOCKADDRESS2 LOCKADDRESS3 LOCKADDRESS4 DIP SWITCH1OFF ON OFF ONDIP SWITCH2 OFF OFF ON ONDIPSWITCHNUMBER:Note:Lock addresses must be used in sequence and cannotbe the same for any two locks connected to a PIB. Forexample, if the system has three locks, use addresses1, 2, and 3 (but not 4). Lock address will correspond topanel address on the PIB.
Form 57032 Rev. A 9VIP 5100 OPEN ARCHITECTURE CYLINDRICAL LOCKINSTALLATION MANUAL01-05-20049. INSTALL INSIDE ESCUTCHEON:Install inside escutcheon assembly onto inside baseplateusing four screws.IMPORTANT!1. MAKE SURE THAT INSIDE SPINDLE ISINSTALLED. 2. PLUG REX SWITCH IN TO BOARD.3. DO NOT PINCH WIRES BETWEEN PARTS.10. SEE PIB MANUAL AND SYSTEM/PANEL MANUAL FOR SET UP PROCEDURES.INSIDE SPINDLEPLUG REX SWITCHINTO PC BOARDDO NOT PINCH WIRESFOR REX SWITCHBETWEEN PARTS

Navigation menu