Schneider Electric Connexium Ethernet Gateway Tsxetg100 Users Manual User's Guide

TSXETG100 to the manual 4dfe6a1d-2a0a-44e8-b6da-b1942a12cd73

2015-02-06

: Schneider-Electric Schneider-Electric-Connexium-Ethernet-Gateway-Tsxetg100-Users-Manual-526954 schneider-electric-connexium-ethernet-gateway-tsxetg100-users-manual-526954 schneider-electric pdf

Open the PDF directly: View PDF .
Page Count: 19

Download
Open PDF In Browser	View PDF

ENGLISH

Instruction Bulletin
ConneXium Ethernet Gateway TSXETG100

63230-319-211A1
2/2006

User’s Guide
Instrucciones en Español: página 19
Instructions en Français: page 39
Anweisungen auf Deutsch: Seite 59
Retain for future use.

TABLE OF CONTENTS

INTRODUCTION ........................................................................................ 2
Supported Ethernet Protocols..................................................................... 2
Hardware .................................................................................................... 2
Additional Resources .................................................................................. 3
ACCESSING THE ETG OVER A NETWORK............................................ 3
Logging into the ETG .................................................................................. 3
Logging Out ................................................................................................ 3
ETG USER INTERFACE OVERVIEW........................................................ 4
SETUP ........................................................................................................ 5
Ethernet and TCP/IP Settings..................................................................... 5
Duplicate IP Address Detection............................................................. 6
Serial Port ................................................................................................... 7
Device List .................................................................................................. 8
Master Mode Device List Setup ............................................................ 8
Slave Mode Device List Setup .............................................................. 9
User Accounts........................................................................................... 10
Web Page Access..................................................................................... 11
Modbus TCP/IP Filtering........................................................................... 12
SNMP Parameters .................................................................................... 13
DIAGNOSTICS ......................................................................................... 14
Statistics.................................................................................................... 14
Interpreting Statistics........................................................................... 15
Read Device Registers ............................................................................. 17
FIRMWARE .............................................................................................. 18
Finding the Firmware Version ................................................................... 18
Getting New Firmware .............................................................................. 18
Updating the Firmware File....................................................................... 18

ConneXium™ Ethernet Gateway
Introduction

INTRODUCTION

63230-319-211A1
2/2006

ENGLISH

This manual is to be used with a ConneXium™ ETG100 with firmware
version 2.0 or higher. For installation information, see the installation guide.
The ETG100 is a communications device that provides connectivity
between Ethernet (Modbus TCP/IP) and serial line devices, allowing
Modbus TCP/IP clients to access information from serial slave devices. It
also allows serial master devices to access information from slave devices
distributed across an Ethernet network.

Supported Ethernet Protocols

The ETG supports the following Ethernet protocols:

•

Modbus TCP/IP: Modbus TCP/IP is a combination of the Modbus
protocol, which provides master-slave communication between devices,
and TCP/IP, which provides communications over an Ethernet
connection. Modbus TCP/IP is used to exchange data between the ETG
and other compatible Modbus TCP/IP devices via TCP port 502.

•

Hypertext Transfer Protocol (HTTP): HTTP is a network protocol that
handles the delivery of files and data on the World Wide Web. It
provides web server functionality via TCP port 80. Remote configuration
of the ETG and the viewing of diagnostic data is possible using a web
browser.

•

File Transfer Protocol (FTP): FTP is a network protocol that provides
the ability to transfer files over the Internet from one computer to
another. FTP is used to transfer firmware updates to the ETG via TCP
port 21.

•

Simple Network Management Protocol (SNMP): Based on MIB2
format, SNMP provides the ability to store and send identifying and
diagnostic information used for network management purposes via UDP
port 161 .

•

Address Resolution Protocol (ARP): ARP is used to convert IP
addresses to Ethernet addresses. ARP requests are sent by the ETG to
determine if its address is a duplicate IP address (see “Duplicate IP
Address Detection” on page 6).

Hardware
RJ45 Ethernet port
Control power

LEDs for Ethernet
and serial
communications

Power and
Status LED

RS485 serial port

Bias, termination,
and 2-wire/4-wire
jumper switches
Reset
button
RS232 serial port
(RJ45 connector)

ConneXium™ Ethernet Gateway
Accessing the ETG Over a Network

Additional Resources

Documentation and Firmware: Go to www.telemecanique.com, select
Products > Products index > Systems and architectures > Connexium.

ACCESSING THE ETG OVER A
NETWORK

After you set up the Ethernet parameters (see the installation guide), you
can access the ETG over an Ethernet LAN using Internet Explorer 6.0 or
higher.

ENGLISH

63230-319-211A1
2/2006

Logging into the ETG
Action

Result

1. Launch Internet Explorer 6.0 or higher.

Opens Internet Explorer.

2. In the Address text box, type the address
of your ETG (169.254.0.10 is the default),
then press Enter.

Opens the Login dialog box.

3. Type your user name (Administrator is the
default) and password (Gateway is the
default) into the text boxes, then click OK.

Enters the user name and password, then
opens the ETG home page.

4. Click Setup to access the ETG setup page, Opens the Setup or Diagnostics pages.
or click Diagnostics to access the ETG
diagnostics page.

Figure 1:

The ETG Home Page

Menu bar

Logging Out

We recommend logging out whenever you do not need access to the ETG.
To log out of the ETG configuration session, click Log Out to end your
session.

ConneXium™ Ethernet Gateway
ETG User Interface OVERVIEW

ENGLISH

ETG USER INTERFACE
OVERVIEW

63230-319-211A1
2/2006

The ETG ships with seven pre-installed web pages used for ETG setup and
configuration. See Table 1 for a description of each web page.
Table 1:

ETG static web pages

ETG Web Page

Description

See
Page

Setup
Ethernet & TCP/IP

Configure Ethernet and TCP/IP communication settings.

Serial Port

Set up or change serial communication parameters.

Device List

Identify serial devices on the daisy chain.

User Accounts➀

Create and edit groups and users.

Web Page Access➀

Select web page access rights for each user group.

Modbus TCP/IP Filtering➀

Set up which IP addresses can access the ETG through
Modbus TCP/IP.

SNMP Parameters➀

Enable and configure the Simple Network Management
Protocol (SNMP), which allows the ETG to identify itself
to network devices requesting SNMP data.

Statistics

Displays diagnostic data used to troubleshoot network
problems. This page also contains information about
your specific ETG, including the serial number,
manufacturing date, and Media Access Control (MAC)
address.

Read Device Registers

Allows ETG administrators to read register data from a
serial device connected to the ETG.

Diagnostics

➀Accessible

by administrator only

63230-319-211A1
2/2006

To access the Setup web page links, click Setup on the ETG menu bar.

ENGLISH

SETUP

ConneXium™ Ethernet Gateway
Setup

Ethernet and TCP/IP Settings
Action

Result

1. From the Setup page, click Ethernet &
TCP/IP.

Opens the Ethernet & TCP/IP page.

2. Select your frame format and media type.
Contact your network administrator if you
do not know.

Selects the frame format and media type.

3. Enter your IP address, subnet mask, and
default gateway address assigned to your
ETG by your network administrator.

Enters the Ethernet parameters for the ETG.

4. Click Apply.

Updates the ETG Ethernet and TCP/IP
settings.

NOTE: If you enter an IP address that is used
by another device, you will be prompted to
select a new IP address. See “Duplicate IP
Address Detection” on page 6.

* See Table 2 on page 5 for a list of options.

NOTE: After making changes to the Ethernet parameters and clicking
Apply, the ETG will reboot.
Figure 2:

Table 2:

Ethernet & TCP/IP Page

ETG Ethernet and TCP/IP Settings

Option

Description

Setting

Frame Format

Used to select the format for data sent over Ethernet II, 802.3 SNAP
an Ethernet connection.
Default: Ethernet II

Media Type

Used to define the physical Ethernet
connection or media type.

IP Address

Used to enter the static IP address of the
ETG.

0.0.0.0 to 255.255.255.255

Subnet Mask

Used to enter the Ethernet IP subnet mask
address of your network.

0.0.0.0 to 255.255.255.255

Default Gateway

Used to enter the gateway (router) IP
0.0.0.0 to 255.255.255.255
address used for wide area network (WAN)
Default: 0.0.0.0
communications.

•
•
•
•
•

10T/100Tx Auto
10BaseT-HD
10BaseT-FD
100BaseTX-HD
100BaseTX-FD

Default: 10T/100Tx Auto

Default: 169.254.0.10
Default: 255.255.0.0

ConneXium™ Ethernet Gateway
Setup

Duplicate IP Address Detection

63230-319-211A1
2/2006

ENGLISH

While connected to your network, the ETG publishes its IP address. To
avoid any duplicate IP address conflicts, the ETG uses the Address
Resolution Protocol (ARP) to see if any other device on your network is
using the same IP address. Table 3 below explains how the ETG handles a
duplicate IP address when it is detected.
Table 3:

Duplicate IP Detection Scenarios

Scenario

Duplicate IP Detected

Boot Process /
Power Restore

Reverts to the default ETG IP
Four blinks, pause pattern
address, subnet mask, and gateway
address. ARP requests are sent every
15 seconds until the IP address is
available. When the IP address
becomes available, the ETG will use
it.

Ethernet Link Detected

Power/Status LED

Manual Address Change ETG keeps it’s previous IP address
and displays a message indicating
that the IP address is already in use
by another device.
Receives an ARP request Reverts to the default ETG IP
address, subnet mask, and gateway
address if a connected device sends
four ARP requests for the ETG’s IP
address. The ETG will send ARP
requests every 15 seconds until the
IP address is available again. When
the IP address becomes available,
the ETG will use it.

Four blinks, pause pattern

63230-319-211A1
2/2006

ConneXium™ Ethernet Gateway
Setup

Serial Port
Result

ENGLISH

Action
1. From the Setup page, click Serial Port.

Opens the Serial Port page.

2. Select your mode, physical interface,
transmission mode, baud rate, parity, and
response timeout (see Table 4 on page 7).

Selects the serial port options.

3. If you select Slave mode, enter the IP
addresses for the remotely connected
devices (see Table 4 on page 7).

Enters the IP addresses of the remote devices.

4. Click Apply.

Updates the ETG Serial Port settings.

Figure 3:

Serial Port Page

Table 4:

Serial Port Settings

Option
Mode

Description
Used to select how the COM port on the
ETG is utilized (master or slave).

Setting
Master, Slave
Default: Master

NOTE: When the Mode is changed, the
ETG reboots.
Physical Interface

Used to select how the ETG serial port is
physically wired.

RS485 4-wire, RS485 2-wire,
or RS232

Transmission
Mode

Used to select how data is transmitted over Modbus RTU, Modbus ASCII
a serial connection.
Default: Modbus RTU

Baud Rate

Used to select the data transmission speed 2400, 4800, 9600, 19200,
over a serial connection.
38400, 56000*, 57600*

Parity

Used to select if data is checked for
accuracy using a parity bit.

Default: RS485 2-wire

Default: 19200
Even, None
Default: Even

Response Timeout Used to select how long the ETG will wait 0.1 to 10 seconds
to receive a response from a serial device. Default: 3 seconds
Used to define a list of Modbus TCP/IP
Remote Modbus
addresses for the ETG to use during slave
TCP/IP
mode communications.
Connections
(Slave mode only)

—

* Available only if the physical interface and transmission mode is RS232/Modbus ASCII.

ConneXium™ Ethernet Gateway
Setup

Device List

63230-319-211A1
2/2006

Before you begin, keep in mind the following:

ENGLISH

For master mode usage of the COM port:

•

Master Mode Device List Setup

Modbus devices do not have to be defined in the Device List, but it helps
you manage your system.

Figure 4:

Master Mode Topology

Ethernet
Connection

ETG in
master
mode
RS485 connection

Up to 128 serial
slave devices
using repeaters

Serial Slave Devices

If you selected Master mode on the Serial Port page, follow the steps below
to set up the device list:
Action

Result

1. From the Setup page, click Device List.

Opens the Device List page.

2. Select the number of viewable devices (1 to Selects the number of viewable locations that
128), then click Apply.
can be used to define serial slave devices
connected to the ETG.
3. In the Local ID text box, type the local ID
(address) of the serial slave device.

Enters the local address of the device.

4. Repeat step 3 until all of the devices are
entered.

Enters all of the connected devices.

5. Click Apply.

Updates the Device List settings.

Figure 5:

Device List Page in Master Mode

63230-319-211A1
2/2006

ConneXium™ Ethernet Gateway
Setup

Figure 6:

Serial port slave mode allows serial Modbus master devices to access
information from serial slave devices across a TCP/IP network. Figure 6
below illustrates how the devices are connected using the device list
settings in Figure 7.

ENGLISH

Slave Mode Device List Setup

Slave Mode Topology
Ethernet
Connection

ETG in master
mode

ETG in
master mode

IP address:
169.254.0.28

IP address:
169.254.0.75

RS485
connection

ETG in
slave mode

RS232 or RS485
connection

RS485
connection

Up to 16 remote IP connections
with up to 128 serial slave devices
are possible

Serial Slave Devices

If you selected Slave mode on the Serial Port page, follow the steps below
to set up the device list:
Action
1. From the Setup page, click Device List.

Result
Opens the Device List page.

2. Select the number of viewable devices (1 to Selects the number of viewable locations that
128), then click Apply.
can be used to define remote Modbus TCP/IP
devices.
3. In the Local ID text box, type the local ID
(address) of the serial slave device.

Enters the address of the device that the local
Modbus master device will use to access the
remote device.

4. In the Remote ID text box, type the remote Enters the serial slave address of the remotely
ID (address) of the serial slave device.
connected device.
5. Select the Connection.

Selects the Modbus TCP/IP address to
associate with the remote ID.

6. Repeat steps 3 through 5 until all of the
devices are entered.

Enters all of the mapping information for the
ETG to communicate to the remote devices.

7. Click Apply.

Updates the Device List settings.

Figure 7:

Device List Page in Slave Mode

ConneXium™ Ethernet Gateway
Setup

User Accounts

63230-319-211A1
2/2006

ENGLISH

ETG users are assigned user names and passwords. Each user belongs to
a group, and each group has access rights to the ETG Web pages assigned
by the ETG administrator.
NOTE: There are two default user accounts: Administrator (password is
Gateway) and Guest (password is Guest).
Action

Result

1. From the Setup page, click User
Accounts.

Opens the User Accounts page.

2. If you want to change a group name, type a Enters a new group name.
new name in one of the Groups text boxes
(the Administrator group name cannot be
changed).
3. In the Users section, enter a Name (1 to 24 Enters the name and password for a user.
characters) and Password (0 to 12
characters) for a new user.
NOTE: User names and passwords are
case-sensitive and can contain only
alphanumeric characters.
4. Select a group and the default language for Selects the group and language for a user.
the new user.
5. Repeat steps 3 and 4 for each additional
user you want to add.

Continues adding users.

6. Click Apply.

Saves all of the user account settings.

Table 5:

ETG accounts and passwords
Account
Gateway

Guest

User-defined accounts (up to 11 accounts possible)

No default –Password is user-defined

Figure 8:

Default Password

Administrator

User Accounts Page

63230-319-211A1
2/2006

ConneXium™ Ethernet Gateway
Setup

Web Page Access
Result
Opens the Web Page Access page.

2. In the Ethernet & TCP/IP row, select the
See Table 6 below for an explanation of access
access level (None, Read-only, or Full) that levels for each group.
each user group will have for the Ethernet &
TCP/IP web page.
Allows the default Guest group to access the
3. To allow Guest access to the web page,
select Read-only under the Guest column. web page.
NOTE: If the Guest group is Read-only,
other groups may only be set to Read-only
or Full.
4. Repeat steps 2 and 3 for the Serial Port,
Device List, Statistics, and Read Device
Registers rows.

Selects the access level for each web page.

5. Click Apply.

Saves the password settings.

Table 6:

Group Access

Group

Access

Administrator

Full access to all web pages
NOTE: We recommend that you change the default administrator
password for system security the first time you log in.

Guest

Read-only access to selected web pages.

Three user-defined
groups

Choosing from the following options, the administrator assigns web
page access for each group. Access levels are as follows:
•
•
•

Figure 9:

None: a group has no access to selected web page
Read-only: password grants a group read-only access to the
selected web page
Full: a group has the same access as the Administrator group to the
selected web page

Web Page Access Page

ENGLISH

Action
1. From the Setup page, click Web Page
Access.

ConneXium™ Ethernet Gateway
Setup

Modbus TCP/IP Filtering

63230-319-211A1
2/2006

ENGLISH

This function allows the administrator to specify Modbus TCP/IP client
devices that have or do not have access to serial slave devices connected
to the ETG.
NOTE: There is an anonymous Modbus TCP/IP address (***.***.***.***) that
can be set to Read-only or None. Setting it to Read-only allows any
Modbus TCP/IP client not in the filtered list to access serial slave devices
with read-only access. Setting it to None blocks all Modbus TCP/IP clients
not in the filtered list.
Action

Result

1. From the Setup page, click Modbus
TCP/IP Filtering.

Opens the Modbus TCP/IP Filtering page.

2. Check Enable Filtering.

Activates filtering.

3. In the IP address column, enter the
Modbus TCP/IP client address

Enters an IP address for a Modbus TCP/IP
client that will have access to the serial devices
connected to the ETG.

4. In the Access Level column, select Readonly or Full.

Selects the access level for the corresponding
IP address. When set to Read-only, only the
following Modbus TCP/IP function codes are
allowed:
Decimal: 1, 2, 3, 4, 7, 8, 11, 12, 17, 20, 24,
43, 100
Hexadecimal: 01, 02, 03, 04, 07, 08, 0B, 0C,
11, 14, 18, 2B, 64

5. Repeat steps 3 and 4 to add more IP
addresses.

Continues adding IP addresses for filtering.

6. Click Apply.

Saves the Modbus TCP/IP address filtering list.

Figure 10:

Modbus TCP/IP Filtering Page

SNMP Parameters

ConneXium™ Ethernet Gateway
Setup

The ETG supports SNMP, allowing a network administrator to remotely
access an ETG with an SNMP manager and view the networking status and
diagnostics in the MIB2 format.
Action
1. From the Setup page, click SNMP
Parameters.

Result
Opens the SNMP Parameters page.

2. Check Enable SNMP to turn ON the simple Activates SNMP.
network management protocol.
NOTE: If you uncheck Enable SNMP and
click Apply, the ETG will reboot and SNMP
functionality will be turned OFF.
3. Enter the system contact, system name,
Enters the SNMP system information and
system location, read-only community
community access names.
name, and the read-write community name.
4. Click Apply.

Figure 11:

Saves the SNMP settings.

SNMP Parameters Page

ENGLISH

63230-319-211A1
2/2006

ConneXium™ Ethernet Gateway
Diagnostics

DIAGNOSTICS

63230-319-211A1
2/2006

ENGLISH

To access the Diagnostics web page links, click Diagnostics on the ETG
menu bar.

Statistics
Action

Result

1. From the Diagnostics page, click
Statistics.

Opens the Statistics page (see Figure 12).

2. View the data.

See “Interpreting Statistics”below.

3. Click Reset.

Resets the ETG cumulative diagnostic data to
0.

NOTE: The Statistics page displays data based
on the mode selected in “Serial Port” on
page 7.

NOTE: This page will show accumulated readings since the ETG was last
activated. If power to the ETG is lost, all cumulative values reset to zero.
Figure 12:

Statistics Page
Reading with Serial Port in MASTER MODE

Reading with Serial Port in SLAVE MODE

63230-319-211A1
2/2006

ConneXium™ Ethernet Gateway
Diagnostics

Interpreting Statistics
Description

Ethernet
Link Status

A status string that represents the speed and
duplex setting being used to communicate with
the linking partner.

Frames Transmitted OK

A counter that increments each time a frame is
successfully transmitted.

Collisions

A counter that increments each time a frame is
retransmitted due to collision detection.

Excessive Collisions

A counter that increments each time a frame is
not able to be sent due to reaching the
maximum collision status based on the
Truncated Binary Exponential Backoff
algorithm.

Frames Received OK

A counter that increments each time a frame is
successfully received.

CRC Errors

A counter that increments each time a frame is
received that has a checksum/CRC that does
not match what is calculated.

Alignment Errors

A counter that increments each time a frame is
received that has a checksum/CRC error and
does not end on an 8-bit frame boundary.

Frames Too Long

A counter that increments each time a frame is
received that is larger than the allowed
maximum size defined in the standards (frames
larger than 1518 bytes).

Frames Too Short

A counter that increments each time a frame is
received that is smaller than the allowed
minimum size defined in the standards (frames
smaller than 64 bytes).

Modbus TCP/IP
Frames Sent

A counter that increments each time a frame is
sent.

Frames Received

A counter that increments each time a frame is
received.

Protocol Errors

A counter that increments each time an
ill-formed message is received.

Active Connectionsc

A status value that represents the number of
connections that are active at the moment the
diagnostics page is refreshed. A maximum of
32 connections are supported. Clicking Active
Connections opens a new window with a list of
all of the active client connections.

Accumulative Connectionsc

A counter that increments each time a
connection is made to the ETG.

Maximum Connectionsc

A status value that represents the maximum
number of connections that were active at any
given moment.

Inbound Read Messagesc

A counter that increments each time a read
request message is received.

Outbound Read Messagesd

A counter that increments each time a read
request message is sent.

Inbound Write Messagesc

A counter that increments each time a write
request message is received.

Outbound Write Messagesd

A counter that increments each time a write
request message is sent.

Inbound Reply Messagesd

A counter that increments each time a reply
message is received.

Outbound Reply Messagesc

A counter that increments each time a reply
message is sent.

c
d

Available when the serial port is in Master mode.
Available when the serial port is in Slave mode

ENGLISH

Statistic

ConneXium™ Ethernet Gateway
Diagnostics

63230-319-211A1
2/2006

Statistic

Description

ENGLISH

Serial Port
Frames Sent

A counter that increments each time a frame is
sent.

Frames Received

A counter that increments each time a frame is
received.

CRC Errors

A counter that increments each time a
message is received that has a CRC that does
not match what is calculated. Typically the
result of wiring issues.

Protocol Errors

A counter that increments each time an illformed message is received.

Timeouts

A counter that increments each time a request
message is sent without receiving a
corresponding response message within the
allowed time. Timeouts are typically the result
of configuration errors or a non-responsive
device.

Inbound Read Messagesd

A counter that increments each time a read
request message is received.

Outbound Read Messagesc

A counter that increments each time a read
request message is sent.

Inbound Write Messagesd

A counter that increments each time a write
request message is received.

Outbound Write Messagesc

A counter that increments each time a write
request message is sent.

Gateway Information
Firmware Version

The firmware version that is installed on the
ETG.

System Idle Time

A percentage from 0% to 100% indicating the
average processor time that is not being used.

MAC Address

The unique Ethernet hardware address of an
ETG.

Serial Number

The serial number of the ETG.

Model Number

The ETG model number (100).

Hardware Version

ETG hardware version.

Manufacture Date

Date the ETG was manufactured.

c
d

Available when the serial port is in Master mode.
Available when the serial port is in Slave mode

63230-319-211A1
2/2006

ConneXium™ Ethernet Gateway
Diagnostics

Read Device Registers
Result
Opens the Read Device Registers page.

2. Enter the device ID, starting register
number, and the number of registers to
read.

Enters the values to begin reading registers for
the specified device.

3. Click Read Holding Registers or Read
Input Registers.

Displays the values for the listed registers.

4. To change how the data is displayed in the Selects how the data values are displayed.
Value column, select Decimal,
Hexadecimal, Binary, or ASCII.

Table 7:

ETG Read Device Register Settings

Option

Description

Device ID

The address of the device that registers are read.

Starting Register

The first register to read.

1
1000

Number of Registers

The number of registers to read (1 to 10).

Lists the register numbers

—

Value column

Lists the data stored in a register.

Decimal, Hexadecimal, Select an option to specify how the Value column
Binary, or ASCII options data is displayed.

Figure 13:

Default

—
Decimal

Read Device Registers Page

ENGLISH

Action
1. From the Diagnostics page, click Read
Device Registers.

ConneXium™ Ethernet Gateway
Instruction Bulletin

FIRMWARE

63230-319-211A1
2/2006

ENGLISH

Firmware on the ETG can be updated using File Transfer Protocol (FTP).
Check www.telemecanique.com or with your local sales representative for
the latest firmware update.

Finding the Firmware Version
Action

Result

1. Log into the ETG.

Opens the ETG home page.

2. Locate the firmware version on the
bottom-left corner of the page.

Determines the firmware version of the ETG.

NOTE: If you recently updated your
firmware, press F5 to refresh the web page
and update the displayed firmware number.
3. Alternatively, you can select Diagnostics > Also determines the firmware version of the
Statistics to find the firmware version in the ETG.
Gateway Information section.

Getting New Firmware
Action

Result

1. Launch Internet Explorer, type
www.telemecanique.com in the Address
text box, then press Enter.

Opens the Telemecanique web site.

2. Select Products, then click Product Index. Opens the Products page.
3. Select Systems and architectures.

Displays the Systems and architectures card.

4. Click ConneXium.

Opens the ConneXium systems and
architectures page.

5. Click Software/firm.

Opens the software/firmware page.

6. Click the firmware file link (eg#####.bin,
Opens the File Download dialog box, then
where ##### is the firmware number), then saves the firmware file.
click Save.

Updating the Firmware File
Action

Result

1. Launch Internet Explorer, type ftp:// and the Opens the Log On As dialog box.
IP address of the ETG in the Address text
box (for example, ftp://169.254.0.10), then
press Enter.
2. Type the user name Administrator and the
administrator password in the text boxes,
then click Log On.

Opens an FTP session with the ETG.

3. Locate the saved firmware file on your
computer, select it, then press CTRL+C.

Copies the firmware file to the clipboard.

4. Right-click in the Internet Explorer window, Copies the firmware to the ETG, and the ETG
then click Paste.
reboots.
NOTE: Instead of copying and pasting the
firmware file, you can drag-and-drop the
firmware file into Internet Explorer.
5. Click the Close button on the Internet
Explorer window.

Closes Internet Explorer and ends the FTP
connection to the ETG.

6. To verify that the firmware version was
Verifies the updated firmware version.
updated successfully, follow the steps in
“Finding the Firmware Version” on page 18.

www.schneider-electric.com
www.telemecanique.com

Electrical equipment should be installed, operated, serviced, and maintained only by
qualified electrical personnel. No responsibility is assumed by Schneider Electric for
any consequences arising out of the use of this material.

ConneXium™ Ethernet Gateway
Handbuch

63230-319-211A1
2/2006

Maßnahme

Ergebnis

5. Schließen Sie das Internet ExplorerFenster.

Schließen von Internet Explorer und Beenden
der FTP-Verbindung zum ETG

6. Um zu kontrollieren, ob die FirmwareVersion erfolgreich aktualisiert wurde,
befolgen Sie die Schritte unter „FirmwareVersion feststellen“ auf Seite 77.

Überprüfung der aktualisierten Firmwareversion

DEUTSCH
www.schneider-electric.com
www.telemecanique.com

eine Marke von

Elektrisches Gerät sollte stets von qualifizierten Elektrikern installiert, betrieben und
gewartet werden. Schneider Electric übernimmt keine Verantwortung für jegliche
Konsequenzen, die sich aus der Verwendung dieses Gerãts ergeben könnten.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2006:02:09 16:54:11Z
Modify Date                     : 2006:04:18 08:33:57-05:00
Page Mode                       : UseOutlines
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Mod Date                        : 2006:04:18 08:33:57-05:00
Creation Date                   : 2006:02:09 16:54:11Z
Author                          : Brian Wilkins
Creator Tool                    : FrameMaker 7.1
Metadata Date                   : 2006:04:18 08:33:57-05:00
Document ID                     : uuid:d6d4114d-a46e-4d29-8be1-a0e55cacfc69
Instance ID                     : uuid:8d7f04c0-bb0a-4e98-a069-a2e232ebc144
Format                          : application/pdf
Title                           : Ethernet Gateway TSXETG100 User's Guide
Creator                         : Brian Wilkins
Page Count                      : 19
Has XFA                         : No

EXIF Metadata provided by EXIF.tools

Schneider Electric Connexium Ethernet Gateway Tsxetg100 Users Manual User's Guide

TSXETG100 to the manual 4dfe6a1d-2a0a-44e8-b6da-b1942a12cd73

Navigation menu

Versions of this User Manual:

Views

Navigation