Se Jin Electron SMB-200F1 RF Mouse User Manual users manual 2
Se Jin Electron Inc RF Mouse users manual 2
Contents
- 1. users manual 1
- 2. users manual 2
- 3. users manual 3
users manual 2
b MOUSE UNiI' (TOP SIDE — i. Left button : used for execute programs — 2. Right button 1 usually used for invoke menu — 3. Scroll Wneei 1 used to scroll window at any time without click scroll bar b KEYBOARD LNIT HOP SIDE) — lamp : used for notiw user working status and power— on blinking P Mouse UNIT (sorrom SIDE) — 1. Ball cover : open to clean bail and roller when movement is not correct — 2. Battery cover: open to out or replace batieriestcheck correct direction) — 3. Fools : 2 tools let user move mouse smoothly and softly WS—200 b MOUSE UN” 0 OP SIDE) — i. Lelt button 1 used for execute programs — 2. Right button 2 usually used for invoke menu — 3. Scroll wheel : used to scroll window at any ime without click scroll bar b KEYBOARD LNIT (to SIDE) — i. Fn keys :if press these keys with pressed Fn key, function inside box is executed — All function is possible with this 100 keys b RECEIVE! UNIT (TOP SIDE) — LED lamp 1. Mouse 1 used for notify user working status and power—on blinking 2. Keyboard : used for notify user working status and power—on blinking 3. NumLock. Capstock. ScrollLock: power—on blinking and toggle function if press each key 4. P512 cable : Keyboard and mouse cable is for PS/2 port and very similar each other. So check carefully before plug in > MOUSE UNtr (BOTTOM srpE) — 1. Ball cover 1 open to clean ball and roller when movement is not correct — 2. Battery cover 1 open to put or replace batteries (check correct direction) — 3. Fools: 2 tools let user move mouse smoothly and softly b MOUSE KEYBOARD UNIT (BOTTOM SIDE) — l. LEG : there is 2 [£65 to adjust angle of keyboard, so user can tix it to favorite angle — 2. Battery cover: open to out or replace batteries (check correct direction) Cuddlonofreoemrmlt WM—200 1. Turn the power off of your lBM compatible PC 2. Plug connector of receiver unit into PS/2 portlkeyboard and mouse is very similar, so be oaretut not to plug in wrong position) 3. Turn the power on of your PC, 4. lamp on receiver unit blink for some seconds (blnking time is difter from the system) 5. ‘WlNG MOUSE is automatically detected by the system. 6. Put 2 AAA batteries in ‘WING MOUSE‘. ll mouse does not work. remove batteries and out again after 10 seconds. If it does not work alter 2 or3 times trial. check battery. 7. After Wrndows°boot. movement of mouse 5 can be easily checked by the lamp of receiver unit. WS—200 1. Turn the power off of your IBM compatible PC(it you must plug during power—on. you must plug mouse cable first) 2. Plug connector of receiver unit into PS/2 portlkevboara and mouse is very similar. so be careful not to plug in wrong position) 3. Turn the power on of your PC. 4. LED lamp on receiver unit blink for some seconds [blinking time is differ from the system) 5. ‘WING MOUSE‘ and WING—KEYBOARD‘ is automatically detected by the system. 6. Put 2 AAA batteries in ‘WlNG lleUSE‘. lt mouse does not work, remove batteries and put again after to seconds. If it does not work after 2 or3 times trial, check battery. 7. Put 2 AA batteries in ‘WlNG KEYBOARD‘. lf keyboard does not work, remove batteries and put again after to seconds. If it does not work al'ter2 or 3 times trialcheck battery. 8. AtlertMndows ® boot, movement of mouse and key press can be easily checked by the LED lamp of receiver unit, 0 Caution when ushg WING MOUSE 1. Don‘t let receiver unit on the floor. Cable can be damaged or some water or dust can damage receiver unit. 2. When using mouse on steel desk, RF antenna sensitivity can be reduced. 3. Use mouse pad for smooth movement and to protect mouse from dust. 4, Place receiver unit as close as possible to the mouse.(within 6 feels] 0 Cleaning mouse ball For smooth and correct movement and for long life, cleaning is important like car. i. Open ball cover from bottom side of mouse 2, Take out ball from mouse 3. Remove dust from ball with velvet or soft cloth 4. Remove dust from roller with thin alcoholic cotton stick [do not use benzene, thinner, acetone) 5. Put ball in mouse and close ball cover 6. Remove dust from foot with soft tooth brush x75
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2001:06:13 12:01:11-04:00 Create Date : 2001:06:13 12:00:51-04:00 Author : ±èÀçÈ« Creator : Microsoft Word 9.0 Producer : Acrobat Distiller 4.05 for Windows Page Count : 3EXIF Metadata provided by EXIF.tools